Get Mirrors -> Auto-dimming mirror/compass with HomeLink (if equipped) Guide for Subaru XV SUV Third Generation (2022-2026)

(221,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

3. To adjust for compass zone variance:

(1) Find your current location and

zone number on the map.

(2) Press and hold the “

” switch for

more than 6 seconds or until a zone

number appears in the display.

(3) Once the zone number appears in

the display, toggle the “

” switch

again until your current location zone

number appears. After you stop press-

ing the switch, your new zone number

will be saved. Within a few seconds,

the display will show a compass direc-

tion.

4. If the vehicle’s magnetics have chan-

ged or if the compass appears inaccurate,

recalibrate the compass. Press and hold

the “

” switch for more than 9 seconds or

until a “C” appears in the display. Once a

“C” appears in the display, slowly drive the

vehicle in circles until compass is cali-

brated.

& Auto-dimming mirror/com-

pass with HomeLink

(if

equipped)

S03AP07

1) Display

2) HomeLink Buttons

3) Switch

During nighttime driving, the auto-dimming

feature senses distracting glare from

vehicle headlights behind you and auto-

matically dims to eliminate the glare and

preserve your vision.

! To Operate the Auto-Dimming Fea-

ture

S03AP0705

Press the “ ” switch to turn the auto-

dimming feature on/off. The auto-dimming

feature is enabled when the switch’s green

LED indicator is on. The auto-dimming

feature will default to on with each ignition

cycle.

! To Operate the Compass Feature

S03AP0706

1. To turn the compass feature on/off,

press and hold the “

” switch for more

than 3 seconds or until the display turns

on/off. The compass feature will default to

on with each ignition cycle.

2. If the display reads “C”, slowly drive the

vehicle in circles until compass is cali-

brated.

Compass calibration zones

3. To adjust for compass zone variance:

(1) Find your current location and

zone number on the map.

(2) Press and hold the “

” switch for

more than 6 seconds or until a zone

number appears in the display.

(3) Once the zone number appears in

– CONTINUED –

Instruments and controls/Mirrors

3-83

(222,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

the display, toggle the “ ” switch

again until your current location zone

number appears. After you stop press-

ing the switch, your new zone number

will be saved. Within a few seconds,

the display will show a compass direc-

tion.

4. If the vehicle’s magnetics have chan-

ged or if the compass appears inaccurate,

recalibrate the compass. Press and hold

the “

” switch for more than 9 seconds or

until a “C” appears in the display. Once a

“C” appears in the display, slowly drive the

vehicle in circles until compass is cali-

brated.

! HomeLink

Wireless Control Sys-

tem

S03AP0704

The HomeLink

Wireless Control System

provides a convenient way to replace up to

three hand-held radio-frequency remotes

used to activate devices such as gate

operators, garage door openers, entry

door locks, security systems, even home

lighting. The below steps are generic

programming instructions; for Genie and

Sommer garage door openers please go

directly to the HomeLink website. Addi-

tional information and programming vi-

deos can be found at

www. and

www.

CAUTION

. Before programming HomeLink

to a garage door opener or gate

operator, make sure that people

and objects are out of the way of

the device to prevent potential

harm or damage.

. When programming a garage

door opener, it is advised to park

outside of the garage.

. Do not use HomeLink with any

garage door opener that lacks

safety stop and reverse features

as required by U.S. federal safety

standards (this includes any gar-

age door opener model manufac-

tured before April 1, 1982). A

garage door that cannot detect

an object signaling the door to

stop and reverse does not meet

current U.S. federal safety stan-

dards.

. It is also recommended that a new

battery be placed in the hand-

held remote (garage door opener

remote) of the device for quicker

and more accurate training.

. Some vehicles may require the

ignition switch to be turned to the

“ON” or “ACC” position for pro-

gramming and/or operation of

HomeLink.

. Keep the hand-held remote (gar-

age door opener remote) of the

device you are programming for

use in other vehicles as well as

for future HomeLink program-

ming. It is also suggested that

upon the sale of the vehicle, the

programmed HomeLink buttons

be erased for security purposes.

Refer to “Erasing HomeLink But-

tons” F3-87.

! Programming a New HomeLink

Button

S03AP070409

1) Indicator Light

2) HomeLink Buttons

Instruments and controls/Mirrors

3-84

(223,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

1. Press and release the HomeLink but-

ton that you would like to program. The

HomeLink indicator light will flash orange

slowly (if not, refer to “Erasing HomeLink

Buttons” F3-87).

1) Garage door opener remote

2. Position the hand-held remote (garage

door opener remote) 1 to 3 inches (2 to 8

cm) away from the HomeLink button that

you would like to program.

NOTE

Some hand-held remotes (garage door

opener remotes) may actually train

better at a distance of 6 to 12 inches

(15 to 30 cm). Keep this in mind if you

have difficulty with the programming

process.

3. While the HomeLink indicator light is

flashing orange, press and hold the hand-

held remote button. Continue pressing the

hand-held remote button until the

HomeLink indicator light changes from

orange to green. You may now release

the hand-held remote button.

NOTE

Some devices may require you to re-

place this “Programming a New

HomeLink Button” step 3 with proce-

dures noted in the “Gate Operator /

Canadian Programming” section. Refer

to “Gate Operator / Canadian Program-

ming” F3-87.

1) Indicator Light

4. Press the HomeLink button that you

would like to program and observe the

indicator light.

. If the indicator light remains constant

green, your device should operate

when the HomeLink button is pressed.

At this point, if your device operates,

programming is complete.

. If the indicator light rapidly flashes

green, firmly press, hold for two sec-

onds and release the HomeLink button

up to three times to complete the

programming process. At this point if

your device operates, programming is

complete. If the device does not

operate, continue with the next step

of the programming instructions.

– CONTINUED –

Instruments and controls/Mirrors

3-85

(224,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

1) “Learn” button

5. At the garage door opener motor,

(security gate motor, etc.) locate the

“Learn”, “Smart”, or “Program” button. This

can usually be found where the hanging

antenna wire is attached to the motor-head

unit (see the device’s manual to identify

this button). The name and color of the

button may vary by manufacturer.

NOTE

A ladder and/or second person may

simplify the following steps.

6. Firmly press and release the “Learn”,

“Smart”, or “Program” button. You now

have 30 seconds in which to complete step

7. Return to the vehicle and firmly press,

hold for two seconds and release the

HomeLink button up to three times. At this

point programming is complete and your

device should operate when the HomeLink

button is pressed and released.

1) Status Indicators

8. If status indicator arrows appear next

to the indicator light, please refer to

“Garage Door Two-Way Communication”

F3-87.

In the event that there are still program-

ming difficulties or questions, additional

HomeLink information and programming

videos can be found at

www. and

www. For

Genie and Sommer garage door openers

please go directly to the HomeLink web-

site.

Instruments and controls/Mirrors

3-86

(226,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

Range may be reduced by obstacles such

as houses or trees. You may have to slow

your vehicle speed to successfully receive

the garage door opener communication.

! Programming Two-Way Commu-

nication

S03AP070414

1) Status Indicators

Within five seconds after programming a

new HomeLink button, both of HomeLink’s

garage door status indicators will flash

rapidly green indicating that the garage

door two-way communication has been

enabled. If your garage door status in-

dicators flashed, two-way communication

programming is complete.

If the garage door status indicators do not

flash, additional HomeLink information

and programming videos can be found

online at www. and

www.

! Using Two-Way Communication

S03AP070415

1) Status Indicators

Recall and display (at any time) the last

recorded garage door status message

communicated to HomeLink by simulta-

neously pressing HomeLink buttons 1 and

2 for two seconds. HomeLink will display

the last recorded status for three seconds.

1) Garage Door Opener CLOSING (Blinking

Orange)

2) Garage Door Opener CLOSED (Solid

Green)

3) Garage Door Opener OPENING (Blink-

ing Orange)

4) Garage Door Opener OPENED (Solid

Green)

If two-way communication programming is

successful, HomeLink will display the

status of your garage door opener with

arrow indicators.

! Certification

S03AP070416

In the event that there are still program-

ming difficulties or questions, additional

HomeLink information and programming

videos can be found at

www.,

www. or

Instruments and controls/Mirrors

3-88

(227,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

by calling the toll-free HomeLink-hotline at

1-800-355-3515.

. U.S.-spec. models

CAUTION

FCC WARNING

Changes or modifications not ex-

pressly approved by the party re-

sponsible for compliance could void

the user’s authority to operate the

equipment.

. Canada-spec. models

– CONTINUED –

Instruments and controls/Mirrors

3-89

(228,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

HomeLink

and the HomeLink

house are

registered trademarks of Gentex Corpora-

tion.

WARNING

. When programming the

HomeLink

Wireless Control Sys-

tem, you may be operating a

garage door opener or other

device. Make sure that people

and objects are out of the way of

the garage door or other device

to prevent potential harm or da-

mage.

. Do not use the HomeLink

Wire-

less Control System with a gar-

age door opener that lacks the

safety stop and reverse feature

as required by applicable safety

standards. A garage door opener

which cannot detect an object,

signaling the door to stop and

reverse, does not meet these

safety standards. Using a garage

door opener without these fea-

tures increases risk of serious

injury or death. For more infor-

mation, consult the HomeLink

website at www. or

call 1-800-355-3515.

& Outside mirrors

S03AP03

! Convex mirror (passenger side)

S03AP0301

WARNING

Objects look smaller in a convex

mirror and farther away than when

viewed in a flat mirror. Do not use the

convex mirror to judge the distance

of vehicles behind you when chan-

ging lanes. Use the inside mirror (or

glance backwards) to determine the

actual size and distance of objects

that you view in convex mirror.

! Remote control mirror switch

S03AP0302

: Select side to adjust

: Direction control

Instruments and controls/Mirrors

3-90

Mirrors -> Auto-dimming mirror/compass with HomeLink (if equipped) for Your Subaru XV SUV Third Generation (2022-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals