Get Emergency Service Guide for Suzuki Baleno 4 Door Second Generation (2015-2021)

EMERGENCY SERVICE

60G411

EMERGENCY SERVICE

Tire Changing Tool ............................................................. 8-1

Jacking Instructions ........................................................... 8-1

Changing Wheels ................................................................ 8-4

Jump Starting Instructions ................................................ 8-5

Towing .................................................................................. 8-6

If the Starter Does Not Operate .......................................... 8-7

If the Engine is Flooded ...................................................... 8-7

If the Engine Overheats ...................................................... 8-8

Warning Triangle ................................................................. 8-9

8-1

EMERGENCY SERVICE

Tire Changing Tool

61MM0B100

(1) Jack

(2) Wheel brace

(3) Jack handle

The tire changing tools are stowed in the

luggage compartment.

Refer to “Luggage Compartment” in the

“ILLUSTRATED TABLE OF CONTENTS”

section.

68PH00801

To remove the spare tire, turn the bolt (1)

counterclockwise and remove it.

Jacking Instructions

68PH00802

1) Place the vehicle on level, hard ground.

2) Set the parking brake firmly and shift

into “P” (Park) if your vehicle has a

CVT, or shift into “R” (Reverse) if your

vehicle has a manual transaxle.

(3)

(2)

(1)

(

)

(

)

(

)

EXAMPLE

WARNING

After using the tire changing tools, be

sure to stow them securely or they

can cause injury if an accident

occurs.

CAUTION

The jack should be used only to

change wheels. It is important to read

the jacking instructions in this sec-

tion before attempting to use the

jack.

(1)

WARNING

• Be sure to shift into “P” (Park) for a

CVT vehicle, or into “R” (Reverse)

for a manual transaxle vehicle

when you jack up the vehicle.

• Never jack up the vehicle with the

transaxle in “N” (Neutral). Other-

wise, unstable jack may cause an

accident.

EXAMPLE

8-2

EMERGENCY SERVICE

3) Turn on the hazard warning flasher if

your vehicle is near traffic.

4) Block the front and rear of the wheel

diagonally opposite of the wheel being

lifted.

5) Place the spare wheel near the wheel

being lifted as shown in the illustration

in case that the jack slips.

54G253

68PH00803

68PH00804

6) Position the jack at an angle as shown

in the illustration and raise the jack by

turning the jack handle clockwise until

the jack-head groove fits around the

jacking bar beneath the vehicle body.

7) Continue to raise the jack slowly and

smoothly until the tire clears the

ground. Do not raise the vehicle more

than necessary.

EXAMPLE

WARNING

• Use the jack only to change wheels

on level, hard ground.

• Never jack up the vehicle on an

inclined surface.

• Never raise the vehicle with the

jack in a location other than the

specified jacking point (shown in

the illustration) near the wheel to

be changed.

• Make sure that the jack is raised at

least 50 mm (2 inch) before it con-

tacts the flange. Use of the jack

when it is within 50 mm (2 inch) of

being fully collapsed may result in

failure of the jack.

• Never get under the vehicle when it

is supported by the jack.

• Never run the engine when the

vehicle is supported by the jack

and never allow passengers to

remain in the vehicle.

8-3

EMERGENCY SERVICE

To Raise the Vehicle with a Garage

Jack

• Apply the garage jack to one of the

points indicated below.

• Always support the raised vehicle with

jack stands (commercially available) at

the points indicated below.

Front jacking point for garage jack (1)

68PH00805

Rear jacking point for garage jack (2)

68PH00806

Application point for jack stand (3)

or two-column lift

68PH00807

(1)

EXAMPLE

(2)

EXAMPLE

(3) (3)

EXAMPLE

8-4

EMERGENCY SERVICE

NOTE:

For more details, please contact an autho-

rised Maruti Suzuki workshop.

Changing Wheels

To change a wheel, use the following pro-

cedure:

1) Clear all passengers and luggage from

the vehicle.

2) Remove the jack, tools and spare

wheel from the vehicle.

3) Loosen, but do not remove the wheel

nuts.

4) Jack up the vehicle.

5) Remove the wheel nuts and wheel.

6) Before installing the new wheel, clean

any mud or dirt off from the surface of

the wheel and hub with a clean cloth.

Clean the hub carefully; it may be hot

from driving.

7) Install the new wheel and replace the

wheel nuts with their cone shaped end

facing the wheel. Tighten each nut

snugly by hand until the wheel is

securely seated on the hub.

68PH00808

Tightening torque for wheel nut

100 Nm (10.2 kg-m, 74.0 lb-ft)

8) Lower the jack and fully tighten the nuts

in a crisscross fashion with a wrench as

shown in the illustration.

NOTICE

Never apply a garage jack to the

exhaust pipe, side under spoiler (if

equipped), engine undercover or rear

torsion beam.

WARNING

Use genuine wheel nuts and tighten

them to the specified torque as soon

as possible after changing wheels.

Incorrect wheel nuts or improperly

tightened wheel nuts may come

loose or fall off, which can result in

an accident. If you do not have a

torque wrench, have the wheel nut

torque checked by an authorised

Maruti Suzuki workshop.

Loosen

Tighten

EXAMPLE

8-5

EMERGENCY SERVICE

Full Wheel Cover (if equipped)

68PH00809

(1) or (2) Flat end tool

Your vehicle includes two tools, a wheel

brace and a jack crank, one of which has a

flat end.

Use the tool with the flat end to remove the

full wheel cap, as shown above.

68PH00810

When installing the cover, make sure that it

is positioned so that it does not cover or

foul the air valve.

Jump Starting Instructions

When Jump Starting Your Vehicle,

Use the Following Procedure:

1) Use only a 12-volt battery to jump start

your vehicle. Position the good 12-volt

battery close to your vehicle so that the

jump leads will reach both batteries.

When using a battery installed on

another vehicle, DO NOT LET THE

VEHICLES TOUCH. Set the parking

brakes fully on both vehicles.

2) Turn off all vehicle accessories, except

those necessary for safety reasons (for

example, headlights or hazard lights).

EXAMPLE

WARNING

• Never attempt to jump start your

vehicle if the battery appears to be

frozen. Batteries in this condition

may explode or rupture if jump

starting is attempted.

• When making jump lead connec-

tions, be certain that your hands

and the jump leads remain clear

from pulleys, belts, or fans.

• Batteries produce flammable

hydrogen gas. Keep flames and

sparks away from the battery or an

explosion may occur. Never smoke

when working in the vicinity of the

battery.

• If the booster battery you use for

jump starting is installed in another

vehicle, make sure the two vehicles

are not touching each other.

• If your battery discharges repeat-

edly, for no apparent reason, have

your vehicle inspected by an

authorised Maruti Suzuki work-

shop.

• To avoid harm to yourself or dam-

age to your vehicle or battery, fol-

low the jump starting instructions

below precisely and in order.

If you are in doubt, call for qualified

road service.

NOTICE

Your vehicle should not be started by

pushing or towing. This starting

method could result in permanent

damage to the catalytic converter.

Use jump leads to start a vehicle with

a weak or flat battery.

8-6

EMERGENCY SERVICE

68PH00811

3) Make jump lead connections as follows:

1. Connect one end of the first jump

lead to the positive (+) terminal of

the flat battery (1).

2. Connect the other end to the positive

(+) terminal of the booster battery

(2).

3. Connect one end of the second jump

lead to the negative (–) terminal of

the booster battery (2).

4. Make the final connection to an

unpainted, heavy metal part (i.e.

engine mount bracket (3)) of the

engine of the vehicle with the flat

battery (1).

4) If the booster battery you are using is

fitted to another vehicle, start the

engine of the vehicle with the booster

battery. Run the engine at moderate

speed.

5) Start the engine of the vehicle with the

flat battery.

6) Remove the jump leads in the exact

reverse order in which you connected

them.

Towing

If you need to have your vehicle towed,

contact a professional service. Your dealer

can provide you with detailed towing

instructions.

2-Wheel Drive (2WD) CVT

CVT vehicles may be towed using either of

the following methods.

1) From the front, with the front wheels

lifted and the rear wheels on the

ground. Before towing, make sure that

the parking brake is released.

2) From the rear, with the rear wheels

lifted and a dolly under the front wheels.

(2)

(1)

(3)

EXAMPLE

WARNING

Never connect the jump lead directly

to the negative (–) terminal of the dis-

charged battery, or an explosion may

occur.

CAUTION

Connect the jump lead to the engine

mount bracket securely. If the jump

lead disconnects from the engine

mount bracket because of vibration

at the start of the engine, the jump

lead could be caught in the drive

belts.

NOTICE

To help avoid damage to your vehicle

during towing, proper equipment and

towing procedures must be used.

NOTICE

Towing the 2WD vehicle with the

front wheels on the ground can result

in damage to the CVT.

8-7

EMERGENCY SERVICE

2-Wheel Drive (2WD) Manual Tran-

saxle

Manual transaxle vehicles may be towed

using either of the following methods.

1) From the front, with the front wheels

lifted and the rear wheels on the

ground. Before towing, make sure that

the parking brake is released.

2) From the rear, with the rear wheels

lifted and the front wheels on the

ground, provided the steering and

drivetrain are in operational condition.

Before towing, make sure that transaxle

is in neutral, the steering wheel is

unlocked (vehicle without keyless push

start system - the ignition key should be

in the “ACC” position) (vehicle with key-

less push start system - the ignition

mode is “ACC”), and the steering wheel

is secured with a clamping device

designed for towing service.

If the Starter Does Not

Operate

1) Try turning the ignition switch to the

“START” position or try pressing the

engine switch to change the ignition

mode to “START” with the headlights

turned on to determine the battery con-

dition. If the headlights go excessively

dim or go off, it usually means that

either the battery is flat or the battery

terminal contact is poor. Recharge the

battery or correct battery terminal con-

tact as necessary.

2) If the headlights remain bright, check

the fuses. If the reason for failure of the

starter is not obvious, there may be a

major electrical problem. Have the vehi-

cle inspected by your authorised Maruti

Suzuki workshop.

If the Engine is Flooded

If the engine is flooded with fuel, it may be

hard to start. If this happens, press the

accelerator pedal all the way to the floor

and hold it there while cranking the engine.

• For petrol engine model, do not operate

the starter motor for more than 12 sec-

onds.

• For diesel engine model, do not operate

the starter motor for more than 30 sec-

onds.

NOTE:

If the engine refuses to start, the starter

motor automatically stops after a certain

period of time. After the starter motor has

automatically stopped or there is anything

abnormal in the engine starting system,

the starter motor runs only while the

engine switch is pressed/ignition switch is

in “on” position.

NOTICE

The steering column is not strong

enough to withstand shocks trans-

mitted from the front wheels during

towing. Always unlock the steering

wheel before towing.

8-8

EMERGENCY SERVICE

If the Engine Overheats

The engine could overheat temporarily

under severe driving conditions. If the

engine coolant temperature gauge indi-

cates overheating during driving:

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and

park.

3) Let the engine run at the normal idle

speed for a few minutes until the indica-

tor is within the normal, acceptable tem-

perature range between “H” and “C”.

If the temperature indication does not

come down to within the normal, accept-

able range:

1) Turn off the engine and check that the

water pump belt and pulleys are not

damaged or slipping. If any abnormality

is found, correct it.

2) Check the coolant level in the reservoir.

If it is found to be lower than the “LOW”

line, look for leaks at the radiator, water

pump, and radiator and heater hoses. If

you locate any leaks that may have

caused the overheating, do not run the

engine until these problems have been

corrected.

3) If you do not find a leak, carefully add

coolant to the reservoir and then the

radiator, if necessary. (Refer to “Engine

Coolant” in the “INSPECTION AND

MAINTENANCE” section.)

NOTE:

If your engine overheats and you are

unsure what to do, contact your authorised

Maruti Suzuki workshop.

79J007

65D350d

WARNING

If you see or hear escaping steam,

stop the vehicle in a safe place and

immediately turn off the engine to let

it cool. Do not open the hood when

steam is present. When the steam

can no longer be seen or heard, open

the hood to see if the coolant is still

boiling. If it is, you must wait until it

stops boiling before you proceed.

EXAMPLE

8-9

EMERGENCY SERVICE

Warning Triangle

MHO07001

In case of vehicle break-down or during

emergency stopping, where, your vehicle

could become a potential traffic hazard,

keep the warning triangle, provided with

your vehicle, on the road free from any

obstacles behind your vehicle so as to

warn the approaching traffic, at an approxi-

mate distance of 50-100 m. The reflecting

side of the triangle should face the on com-

ing traffic. Please activate the hazard

warning lamps before alighting the vehicle

to keep the warning triangle.

MHO07014

• Remove the warning triangle carefully

from the cover as shown by arrow 1.

• Open both the reflector arms as shown

by arrow and lock the arms with each

other with the clip provided in the right

arm. Open the bottom stand in counter

clock-wise direction as shown by arrow

3. Position the warning triangle behind

the vehicle on a plain surface.

• Reverse the removal procedure for keep-

ing inside the cover.

MHO07015

WARNING

• It is hazardous to remove the radia-

tor cap (or degassing tank cap for a

diesel engine) when the water tem-

perature is high, because scalding

fluid and steam may be blown out

under pressure. The cap should

only be taken off when the coolant

temperature has lowered.

• To help prevent personal injury,

keep hands, tools and clothing

away from the engine cooling fan

and air-conditioner fan (if

equipped). These electric fans can

automatically turn on without warn-

ing.

EXAMPLE

Emergency Service for Your Suzuki Baleno 4 Door Second Generation (2015-2021)

Related Topics

Popular Owner Manuals

Latest Owner Manuals