Get Inspection and Maintenance -> Bulb Replacement Guide for Suzuki Baleno 4 Door Second Generation (2015-2021)

7-28

INSPECTION AND MAINTENANCE

81A283

Headlight Aiming

Since special procedures are required, we

recommend you take your vehicle to your

authorised Maruti Suzuki workshop for

headlight alignment.

Bulb Replacement

WARNING

Always be sure to replace a blown

fuse with a fuse of the correct amper-

age. Never use a substitute such as

aluminum foil or wire to replace a

blown fuse. If you replace a fuse and

the new one blows in a short period

of time, you may have a major electri-

cal problem. Have your vehicle

inspected immediately by your

authorised Maruti Suzuki workshop.

BLO W NOK

CAUTION

• Light bulbs can be hot enough to

burn your finger right after being

turned off. This is true especially

for halogen headlight bulbs.

Replace the bulbs after they

become cool enough.

• The headlight bulbs are filled with

pressurized halogen gas. They can

burst and injure you if they are hit

or dropped. Handle them carefully.

• To avoid injury by sharp-edged

parts of the body, wear gloves and

a long-sleeved shirt when replacing

light bulbs.

NOTICE

The oils from your skin may cause a

halogen bulb to overheat and burst

when the lights are on. Grasp a new

bulb with a clean cloth.

NOTICE

Frequent replacement of a bulb indi-

cates the need for an inspection of

the electrical system. This should be

carried out by your authorised Maruti

Suzuki workshop.

7-29

INSPECTION AND MAINTENANCE

Headlights

Discharge headlights

Since special procedures are required, we

recommend you take your vehicle to your

authorised Maruti Suzuki workshop for

bulb replacement.

Halogen headlights

68PH00726

(1) Headlight (High/Low Beam)

68PH00727

Open the engine food. Disconnect the cou-

pler (1). Remove the sealing rubber (2).

Push the retaining spring (3) forward and

unhook it. Then remove the bulb. Install a

new bulb in the reverse order of removal.

68PH00728

NOTE:

You can see the position of retaining spring

from the hole of headlight.

WARNING

Never attempt to replace the bulb of a

discharge headlight, or you could

suffer an electric shock from the

high-voltage circuit in the headlight

system. Always have a discharge

headlight bulb replaced by an autho-

rised Maruti Suzuki workshop.

(1)

(2)

(1)

(3)

WARNING

Don’t twist/shake the bulb coupler

while removing as it may disturb the

terminal gap leading to loose connec-

tion and sparking causing subse-

quent coupler melting/ fire.

7-30

INSPECTION AND MAINTENANCE

Side Turn Signal Light (on fender)

(if equipped)

68PH00729

1) Remove the light housing (1) by sliding

to left with your finger.

68PH00760

2) Turn the bulb holder (2) clockwise and

pull it out from the light housing.

68PH00761

(4) Removal

(5) Install

3) To remove and install the bulb of the

side turn signal light (3), simply pull out

or push in the bulb.

(1)

(2)

(3)

(4)

(5)

EXAMPLE

7-31

INSPECTION AND MAINTENANCE

Front turn signal light and

front position light

Vehicle with the halogen headlights

68PH00730

(1) Front turn signal light

(2) Front position light

Vehicle with the discharge headlights

68PH00731

(1) Front turn signal light

68PH00732

1) Open the engine hood. To remove the

bulb holder of the front turn signal light

or the front position light from the light

housing, turn the holder counterclock-

wise and pull it out.

(1)

(2)

(1)

EXAMPLE

7-32

INSPECTION AND MAINTENANCE

68PH00733

(3) Removal

(4) Installation

2) To remove the bulb of the front turn sig-

nal light (1) from the bulb holder, push

in the bulb and turn it counterclockwise.

To install a new bulb, push it in and turn

it clockwise.

To remove and install the bulb of the

front position light (2), simply pull out or

push in the bulb.

Front Fog Light (if equipped)

1) Start the engine. Turn the steering

wheel to the opposite side of the replac-

ing fog light to replace the bulb easily.

Then turn off the engine.

68PH00734

2) Remove the clips (1).

68PH00735

3) Open the end of the cover inside the

fender.

(1)

(2)

(3)

(4)

EXAMPLE

(1)

EXAMPLE

7-33

INSPECTION AND MAINTENANCE

68PH00736

4) Disconnect the coupler by pushing the

lock release. Turn the bulb holder coun-

terclockwise and remove it.

Rear combination light

68PH00737

1) Remove the bolts (1) and pull the light

housing (2) straight.

68PH00738

2) Remove the wire (3) from a clamp (4).

EXAMPLE

(1)

(2)

(4)

(3)

7-34

INSPECTION AND MAINTENANCE

68PH00739

3) To remove the bulb holder of the rear

turn signal light (5) or the reversing light

(6) from the light housing, turn the

holder counterclockwise and pull it out.

68PH00740

(7) Removal

(8) Installation

4) To remove the bulb of the rear turn sig-

nal light (5) from the bulb holder, push

in the bulb and turn it counterclockwise.

To install a new bulb, push it in and turn

it clockwise.

To remove and install the bulb of the

reversing light (6), simply pull out or

push in the bulb.

68PH00741

NOTE:

When reinstalling the light housing, check

that the clips are properly attached.

(6)

(5)

(6)

(7)

(8)

EXAMPLE

7-35

INSPECTION AND MAINTENANCE

License Plate Light

68PH00742

1) Turn the cover (1) counterclockwise to

remove it.

68PH00743

2) To remove and install the bulb of the

license plate light (2), simply pull out or

push in the bulb.

Interior Light

Remove the lens by using a flat blade

screwdriver covered with a soft cloth as

shown. To install it, simply push it back in.

Front (if equipped)

68PH00744

(1)

(2)

7-36

INSPECTION AND MAINTENANCE

Center

68PH00745

Luggage compartment (if equipped)

68PH00746

Courtesy light (if equipped)

68PH00747

Glove Box Light (if equipped)

Since special procedures are required, we

recommend you take your vehicle to your

authorised Maruti Suzuki workshop for

bulb replacement.

68PH00748

1) Press inward on both sides of the glove

box and pull frontward and then

unclamp it.

EXAMPLE

7-37

INSPECTION AND MAINTENANCE

68PH00749

2) To remove and install the bulb of the

glove box light (1), simply pull out or

push in the bulb.

Wiper Blades

54G129

If the wiper blades become brittle or dam-

aged, or make streaks when wiping,

replace the wiper blades.

To install new wiper blades, follow the pro-

cedures below.

NOTE:

Some wiper blades may be different from

the ones described here depending on

vehicle specifications. If so, consult your

authorised Maruti Suzuki workshop for

proper replacement method.

For windshield wipers:

70G119

1) Hold the wiper arm away from the win-

dow.

NOTE:

When raising both of the front wiper arms,

pull the driver’s side wiper arm up first.

When returning the wiper arms, lower the

passenger’s side wiper arm first. Other-

wise, the wiper arms may interfere with

each other.

(1)

EXAMPLE

NOTICE

To avoid scratching or breaking the

window, do not let the wiper arm

strike the window while replacing the

wiper blade.

Inspection and Maintenance -> Bulb Replacement for Your Suzuki Baleno 4 Door Second Generation (2015-2021)

Related Topics

Popular Owner Manuals

Latest Owner Manuals