Get Before Driving -> Seat Belts and Child Restraint Systems Guide for Suzuki Grand Vitara SUV Second Generation (2005-2015)

2-26

BEFORE DRIVING

79K21-03E

64J091

2) Pull down the seat cushion until it locks

into place.

64J092

3) Raise the seatback until it locks into

place.

After returning the seat, try moving the

seat and seatback to make sure they are

securely latched.

Seat Belts and Child Restraint

Systems

65D231S

WARNING

When returning the rear seat cushion

to the normal position, be careful that

your finger is not caught between the

lock and the floor.

CAUTION

• When returning the rear seat cush-

ion to the normal position, make

sure that there is nothing around

the striker. Any foreign materials

prevent the seat cushion from

being locked securely.

• When returning the rear seat cush-

ion to the normal position, make

sure that there is nothing under the

seat cushion. This prevents dam-

age to the seat cushion.

WARNING

An air bag supplements, or adds to,

the frontal crash protection offered

by seat belts. The driver and all pas-

sengers must be properly restrained

by wearing seat belts at all times,

whether or not an air bag is mounted

at their seating position, to minimize

the risk of severe injury or death in

the event of a crash.

Seat Belts and Child Restraint Systems: 14

2-27

BEFORE DRIVING

79K21-03E

65D606 65D201 65D199

WARNING

• Never allow persons to ride in the

cargo area of a vehicle. In the event

of an accident, there is a much

greater risk of injury for persons

who are not riding in a seat with

their seat belt securely fastened.

• Seat belts should always be

adjusted as follows:

– the lap portion of the belt should

be worn low across the pelvis,

not across the waist.

– the shoulder straps should be

worn on the outside shoulder

only, and never under the arm.

– the shoulder straps should be

away from your face and neck,

but not falling off your shoulder.

(Continued)

Above the pelvis

WARNING

(Continued)

• Seat belts should never be worn

with the straps twisted and should

be adjusted as tightly as is com-

fortable to provide the protection

for which they have been designed.

A slack belt will provide less pro-

tection than one which is snug.

(Continued)

Across the pelvis

WARNING

(Continued)

• Pregnant women should use seat

belts, although specific recommen-

dations about driving should be

made by the woman’s medical advi-

sor. Remember that the lap portion

of the belt should be worn as low

as possible across the hips, as

shown in the diagram.

• Make sure that each seat belt

buckle is inserted into the proper

buckle catch. It is possible to cross

the buckles in the rear seat.

(Continued)

as low as possible

across the hips

Seat Belts and Child Restraint Systems: 14

2-28

BEFORE DRIVING

79K21-03E

Lap-Shoulder Belt

Emergency Locking Retractor (ELR)

The lap-shoulder seat belt has an emer-

gency locking retractor (ELR), which is

designed to lock the seat belt only during a

sudden stop or impact. It also may lock if

you pull the belt across your body very

quickly. If this happens, let the belt go back

to unlock it, then pull the belt across your

body more slowly.

Automatic Locking Retractor (ALR)

The front passenger’s seat belt and the

rear seat belts have emergency locking

retractors (ELRs) that can be temporarily

converted to function as automatic locking

retractors (ALRs). The ALR mode should

be used if you need to secure a child

restraint system in the seat. Refer to the

“Child Restraint Systems” section for

details.

WARNING

(Continued)

• Do not wear your seat belt over

hard or breakable objects in your

pockets or on your clothing. If an

accident occurs, objects such as

glasses, pens, etc. under the seat

belt can cause injury.

• Never use the same seat belt on

more than one occupant and never

attach a seat belt over an infant or

child being held on an occupant’s

lap. Such seat belt use could cause

serious injury in the event of an

accident.

• Periodically inspect seat belt

assemblies for excessive wear and

damage. Seat belts should be

replaced if webbing becomes

frayed, contaminated, or damaged

in any way. It is essential to replace

the entire seat belt assembly after it

has been worn in a severe impact,

even if damage to the assembly is

not obvious.

• Children age 12 and under should

ride properly restrained in the rear

seat, if equipped.

(Continued)

WARNING

(Continued)

• Infants and small children should

never be transported unless they

are properly restrained. Restraint

systems for infants and small chil-

dren can be purchased commer-

cially and should be used. Make

sure that the system you purchase

meets Federal Motor Vehicle Safety

Standards. Read and follow all the

directions provided by the manu-

facturer.

• Avoid contamination of seat belt

webbing by polishes, oils, chemi-

cals and particularly battery acid.

Cleaning may safely be carried out

using mild soap and water.

• For children, if the shoulder belt

irritates the neck or face, move the

child closer to the center of the

vehicle.

• All seatbacks should always be in

an upright position when driving,

or seat belt effectiveness may be

reduced. Seat belts are designed to

offer maximum protection when

seatbacks are in the upright posi-

tion.

Seat Belts and Child Restraint Systems: 14

2-29

BEFORE DRIVING

79K21-03E

Safety reminder

60A038

60A040

To reduce the risk of sliding under the belt

during a collision, position the lap portion

of the belt across your lap as low on your

hips as possible and adjust it to a snug fit

by pulling the shoulder portion of the belt

upward through the latch plate. The length

of the diagonal shoulder strap adjusts itself

to allow freedom of movement.

60A036

To fasten the seat belt, sit up straight and

well back in the seat, pull the latch plate

attached to the seat belt across your body

and press it into the buckle until you hear a

“click”.

Sit up straight and

fully back

Low on hips

Seat Belts and Child Restraint Systems: 14

2-30

BEFORE DRIVING

79K21-03E

78K126

NOTE:

The word “CENTER” is molded into the

buckle for the rear seat center belt. The

buckles are designed so a latch plate can-

not be inserted into the wrong buckle.

60A039

To unfasten the belt, push the red

“PRESS” button on the buckle and allow

the belt to retract.

Seat Belt Reminder

Driver’s seat belt reminder light

79K117

Front passenger’s seat belt reminder

light

66J243

When the driver and front passenger don’t

buckle their seat belts, the driver’s seat belt

EXAMPLE

Seat Belts and Child Restraint Systems: 14

2-31

BEFORE DRIVING

79K21-03E

reminder light in the instrument cluster and

the front passenger’s seat belt reminder

light in the center of the instrument panel

will come on and a buzzer will sound as a

reminder to the driver and front passenger

to buckle their seat belts.

The seat belt reminder functions as shown

in the figure below. There are some differ-

ences between the driver’s seat belt

reminder and the front passenger’s seat

belt reminder. For more details, refer to the

explanation below.

WARNING

It is absolutely essential that the

driver and passengers wear their seat

belts at all times. Persons who are

not wearing seat belts have a much

greater risk of injury if an accident

occurs. Make a regular habit of buck-

ling your seat belt before putting the

key in the ignition.

Flow chart

52D219

Reminder 1 – 3

For each reminder 1 – 3, the reminder light comes on for about 20 seconds, then blinks for

about 55 seconds. When the reminder light first comes on, a buzzer sounds intermittently

for about 6 seconds.

Ignition Switch “ON”

Seat belt is

buckled

30 sec.

Reminder 1

Vehicle speed:

increase to 8 km/h

Seat belt is

unbuckled

Vehicle speed:

below 8 km/h

Vehicle speed:

over 8 km/h

Reminder 3

No reminder

3 min.

Reminder 2

No reminder

Seat belt is

unbuckled

Vehicle speed:

below 8 km/h

Vehicle speed:

over 8 km/h

Seat Belts and Child Restraint Systems: 14

2-32

BEFORE DRIVING

79K21-03E

Driver’s seat belt reminder

If the driver’s seat belt remains unbuckled

with the ignition key in the “ON” position,

the driver’s seat belt reminder works as fol-

lows:

1) The driver’s seat belt reminder light will

come on for about 20 seconds when

the ignition key is turned to the “ON”

position then will blink for about 55 sec-

onds. When the light comes on, a

buzzer will also sound intermittently for

about 6 seconds (Reminder 1).

2) If the vehicle is driven (vehicle speed >

8 km/h), Reminder 2 will operate about

30 seconds after Reminder 1 has fin-

ished.

If the vehicle is not driven (vehicle

speed < 8 km/h), Reminder 2 will oper-

ate when driving starts (vehicle speed >

8 km/h).

3) Reminder 3 will operate about 3 min-

utes after Reminder 2 has finished.

4) Even if the driver’s seat belt remains

unbuckled after Reminder 3, there will

be no further reminders.

If the driver has buckled his or her seat belt

and later unbuckles the seat belt, the

reminder system will be activated from

Reminder 1 or Reminder 2 according to

the vehicle speed. (Refer to the flow chart.)

The driver’s seat belt reminder will be auto-

matically canceled when the driver’s seat

belt is buckled or the ignition switch is

turned off.

Front passenger’s seat belt reminder

The front passenger’s seat belt reminder

will activate only when there is a passen-

ger sitting in the front seat. In some situa-

tions, however, such as when you place

heavy objects in the front seat, the seat

belt reminder can be activated as if there

were a passenger present. The front pas-

senger’s seat belt reminder works in the

same manner as the driver’s seat belt

reminder, except that it is not activated

until 10 seconds after the ignition switch is

turned to the “ON” position.

Shoulder anchor height adjuster

(if equipped)

64J198

Adjust the shoulder anchor height so that

the shoulder belt rides on the center of the

outside shoulder. To upward, slide the

anchor up. To downward, slide the anchor

down while pulling the lock knob out. After

adjustment, make sure that the anchor is

securely locked.

WARNING

Be sure that the shoulder belt is posi-

tioned on the center of the outside

shoulder. The belt should be away

from your face and neck, but not fall-

ing off your shoulder. Misadjustment

of the belt could reduce the effective-

ness of the safety belt in a crash.

EXAMPLE

Seat Belts and Child Restraint Systems: 14

2-33

BEFORE DRIVING

79K21-03E

Seat Belt Inspection

65D209

Periodically inspect the seat belts to make

sure they work properly and are not dam-

aged. Check the webbing, buckles, latch

plates, retractors, anchorages and guide

loops. Replace any seat belts which do not

work properly or are damaged.

Child Restraint Systems

60G332

Infant restraint - rear seat only

65D202

EXAMPLE

WARNING

Be sure to inspect all seat belt

assemblies after any collision. Any

seat belt assembly which was in use

during a collision (other than a very

minor one) should be replaced, even

if damage to the assembly is not

obvious. Any seat belt assembly

which was not in use during a colli-

sion should be replaced if it does not

function properly, it is damaged in

any way or the seat belt pretension-

ers were activated (that is, if the front

air bags were activated).

EXAMPLE

Seat Belts and Child Restraint Systems: 14

2-34

BEFORE DRIVING

79K21-03E

Infant restraint - rear seat only

65D584

Booster seat

65D203

SUZUKI highly recommends that you use

a child restraint system to restrain infants

and small children. Many different types of

child restraint systems are available; make

sure that the restraint system you select

meets Federal Motor Vehicle Safety Stan-

dards.

All child restraint systems are designed to

be secured in vehicle seats by either seat

belts (lap belts or the lap portion of lap-

shoulder belts) or by special rigid lower

anchor bars built into the seats. Whenever

possible, SUZUKI recommends that child

restraint systems be installed on the rear

seat. According to accident statistics, chil-

dren are safer when properly restrained in

rear seating positions than in front seating

positions.

If you must use a front-facing child restraint

in the front passenger’s seat, be sure to

move the front passenger’s seat as far

back as possible.

EXAMPLE

WARNING

Children could be endangered in a

crash if their child restraints are not

properly secured in the vehicle.

When installing a child restraint sys-

tem, be sure to follow the instruc-

tions below. Be sure to secure the

child in the restraint system accord-

ing to the manufacturer’s instruc-

tions.

WARNING

In an accident or sudden stop, the

rear seat armrest (if equipped) could

fall forward. If there is a child in a

rear-facing child restraint in the cen-

ter seating position, the falling arm-

rest could injure the child. Make sure

the armrest is back in the seat and

locked when not in use.

Seat Belts and Child Restraint Systems: 14

2-35

BEFORE DRIVING

79K21-03E

65D607 65D608

65D609

Installation with Lap-Shoulder Seat

Belts (Child Restraint with No Top

Strap)

NOTE:

There are two types of lap-shoulder belts

depending on the vehicle’s specification,

A-ELR (Automatic-Emergency Locking

Retractor) type and ELR (Emergency

Locking Retractor) type.

The A-ELR type belts have emergency

locking retractors (ELRs) that can be tem-

porarily converted to function as automatic

locking retractors (ALRs).

The ELR type belts have ELRs that cannot

be converted to function as ALRs.

To identify the belt is the A-ELR type or the

ELR type, slowly pull all of the shoulder

webbing out of the retractor. Then let the

webbing retract a little and pull it out, and

repeat this a few times. If the belt is locked

each time you pull the belt, the belt is the

A-ELR type. If the belt is not locked, the

belt is the ELR type.

Please note that the methods to secure the

child restraint system with the ELR lap-

shoulder belt and with the A-ELR lap-

shoulder belt are different.

WARNING

Do not install a rear-facing child

restraint in the front passenger’s

seat. If the passenger’s air bag

inflates, a child in a rear-facing child

restraint could be seriously injured.

The back of a rear-facing child

restraint would be too close to the

inflating air bag.

CAUTION

Before installing a child restraint sys-

tem in the rear seat, raise the head

restraint to the most upper position.

Seat Belts and Child Restraint Systems: 14

2-36

BEFORE DRIVING

79K21-03E

ELR type belt

65D233

Install your child restraint system accord-

ing to the instructions provided by the child

restraint system manufacturer.

Make sure that the seat belt is securely

latched.

Try to move the child restraint system in all

directions to make sure it is securely

installed.

A-ELR type belt

83E031

Install your child restraint system accord-

ing to the instructions provided by the child

restraint system manufacturer. If you install

the child restraint system in the front seat,

be sure to slide the seat to the rearmost

position. After making sure that the seat

belt is securely latched:

A-ELR type

83E035

1) Pull all of the remaining webbing out of

the retractor. You will hear a click, which

means that the emergency locking

retractor (ELR) has converted to func-

tion as an automatic locking retractor

(ALR).

EXAMPLE EXAMPLE

EXAMPLE

Seat Belts and Child Restraint Systems: 14

Supplemental Restraint System (air bags): 3, 9, 12

2-37

BEFORE DRIVING

79K21-03E

A-ELR type

83E032

2) Allow the extra webbing to retract, and

pull the webbing toward the retractor to

take up any slack. Make sure that the

lap portion of the belt is tight around the

child restraint system and the shoulder

portion of the belt is positioned so that it

cannot interfere with the child’s head or

neck.

A-ELR type

83E036

3) Make sure that the retractor has con-

verted to the ALR mode by trying to pull

webbing out of the retractor. If the

retractor is in the ALR mode, the belt

will be locked.

A-ELR type

65D234

A-ELR type

65D235

4) Try moving the child restraint system in

all directions, to make sure it is securely

installed. If you need to tighten the belt,

pull more webbing toward the retractor.

EXAMPLE

WARNING

If the retractor is not in the ALR

mode, the child restraint system can

move or tip over when your vehicle

turns or stops abruptly.

EXAMPLE EXAMPLE

Move to check

EXAMPLE

Pull to tighten

Supplemental Restraint System (air bags): 3, 9, 12

2-38

BEFORE DRIVING

79K21-03E

To revert from ALR to ELR

65D267

When you unbuckle the seat belt and allow

it to retract to a certain length, the retractor

will automatically revert back to the normal

ELR mode.

Installation with the LATCH System

66J162

Rear seat

64J027

Your vehicle is equipped with lower

anchors for securing up to two standard

LATCH-type child restraints in the rear

seats. (LATCH stands for Lower Anchors

and Tethers for Children.) The anchors are

located where the rear of the seat cushion

meets the bottom of the seatback.

Install a LATCH-type child restraint system

according to the instructions provided by

the child restraint system manufacturer.

After installing the child restraint system,

try moving it in all directions, especially for-

ward to make sure the flexible straps or

rigid connecting bars are securely latched

to the anchors.

NOTE:

Although there are three second row seat-

ing positions, you cannot install three

LATCH type child restraints in the rear

seat. You can install one or two LATCH

restraint(s). Be sure to install the LATCH

type child restraint(s) in the outboard seat-

ing positions.

If your LATCH restraint has flexible lower

connecting straps, these general instruc-

tions apply:

1) If possible, fold the seatback rearward

for easier installation.

2) Place the child restraint in the rear seat.

EXAMPLE

Rigid lower connecting

bar type

Flexible lower connecting

strap type

Supplemental Restraint System (air bags): 3, 9, 12

2-39

BEFORE DRIVING

79K21-03E

65D340

3) Snap the strap hooks to the anchors.

Take care not to pinch your fingers.

65D341

4) Return the seatback to the normal,

upright position. Tighten the lower

straps as described in the child restraint

owner’s manual. Attach the top tether

strap, if applicable.

65D342

5) Make sure the child restraint is securely

fastened by trying to move the child

restraint system in all directions, espe-

cially forward.

If your LATCH restraint has rigid lower con-

necting bars, these general instructions

apply:

1) If possible, fold the seatback rearward

for easier installation.

2) Place the child restraint in the rear seat,

inserting the connecting bars through

the slots in the seat cushion or the slots

in the seatback bottom.

54G183

3) Use your hands to carefully align the

connecting bar tips with the anchors.

Take care not to pinch your fingers.

EXAMPLE

WARNING

The seatback should always be

securely latched in a fairly upright

position when any type of child seat

is installed. An unlatched or reclined

seatback will reduce the intended

effectiveness of the child restraint

system.

EXAMPLE

Supplemental Restraint System (air bags): 3, 9, 12

2-40

BEFORE DRIVING

79K21-03E

54G184

4) Push the child restraint toward the

anchors so that the connecting bar tips

are partially hooked to the anchors.

Use your hands to confirm the position.

54G185

5) Grasp the front of the child restraint and

push the child restraint forcefully to

latch the connecting bars. Make sure

they are securely latched by trying to

move the child restraint system in all

directions, especially forward.

6) Return the seatback if folded. Attach

the top tether strap, if applicable.

Installation-Child Restraint with Top

Strap

Rear seat

79K026

Some child restraint systems require the

use of a top strap. Top strap anchor brack-

ets are located on the back of the rear seat

as shown in the illustration. Install the child

restraint system as follows:

1) Remove the luggage compartment

cover.

2) Secure the child restraint on the rear

seat using the procedure described

above for securing a restraint system

that does not require a top strap.

3) Hook the top strap to the anchor

bracket and tighten the top strap

according to the instructions provided

by the child restraint system manufac-

turer. Be sure to attach the top strap to

the corresponding anchor located

directly behind the child restraint. Do

EXAMPLE

WARNING

The seatback should always be

securely latched in a fairly upright

position when any type of child seat

is installed. An unlatched or reclined

seatback will reduce the intended

effectiveness of the child restraint

system.

EXAMPLE

Front

Supplemental Restraint System (air bags): 3, 9, 12

2-41

BEFORE DRIVING

79K21-03E

not attach the top strap to the luggage

restraint loops (if equipped).

86G032

4) When routing the top strap, be sure to

pass it between the head restraint and

the rear seatback as shown. (Refer to

“Head Restraints” section for details on

how to raise or lower the head

restraint.)

5) Make sure that cargo does not interfere

with routing of the top strap.

Seat Belt Extender

65D613

(1) Center of body

(2) Less than 152 mm (6 inches)

(3) Open end of extender buckle

If a seat belt cannot be fastened securely

because it is not long enough, see your

authorized SUZUKI dealer for a seat belt

extender. Seat belt extenders are available

for each seating position except for the

rear center position. After inspecting the

relationship between the seat belt length,

the occupant’s body size, and the seat

adjustment (the driver’s seat should always

be adjusted as far back as possible while

still maintaining control of the vehicle, and

other adjustable seats should be adjusted

as far back as possible), your dealer can

select the appropriate seat belt extender.

• A seat belt extender should only be used

for the person, vehicle and seating loca-

tion it was provided for.

• When using the extender, ensure that

both ends are latched securely. Do not

use the extender if the open end of the

extender’s buckle is within 152 mm (6

inches) of the center of the occupant’s

body (See diagram). Use of the extender

when the buckle is too close to the cen-

ter of the body could increase the risk of

abdominal injury in the event of an acci-

dent, and could cause the shoulder belt

to be positioned incorrectly.

• Make sure to use the correct buckle cor-

responding to your seating position.

• Seat belt extenders are not intended for

use by pregnant women, and should

only be used upon approval by their

medical advisors.

• Remove and stow the extender when it

is not being used.

WARNING

Do not attach the child restraint top

strap to the luggage restraint loops

(if equipped). Incorrectly attached top

strap will reduce the intended effec-

tiveness of the child restraint system.

Type 2

Type 1

Supplemental Restraint System (air bags): 3, 9, 12

2-42

BEFORE DRIVING

79K21-03E

Seat Belt Pretensioner System

(for front seat belt only)

52D011

Your vehicle is equipped with a seat belt

pretensioner system at the front seating

positions. You can use the pretensioner

seat belts in the same manner as ordinary

seat belts.

The seat belt pretensioner system works

with the SUPPLEMENTAL RESTRAINT

SYSTEM (advanced air bags). The crash

sensors and the electronic controller of the

air bag system also control the seat belt

pretensioners. The pretensioners are trig-

gered only when the air bags are triggered

and the seat belts are fastened. If the seat

belts are not fastened, the respective pre-

tensioner system will not be activated. For

precautions and general information

including servicing the pretensioner sys-

tem, refer to the “Supplemental Restraint

System (air bags)” section in addition to

this “Seat Belt Pretensioner System” sec-

tion, and follow all those precautions.

The pretensioner is located in each front

seat belt retractor. The pretensioner tight-

ens the seat belt in the event of a frontal

crash or a rollover. The retractors will

remain locked after the pretensioners are

activated. Upon activation, some noise will

occur and some smoke may be released.

These conditions are not harmful and do

not indicate a fire in the vehicle.

The driver and all passengers must be

properly restrained by wearing seat belts

at all times, whether or not a pretensioner

is equipped at their seating position, to

help minimize the risk of severe injury or

death in the event of a frontal crash or a

rollover.

Sit fully back in the seat; sit up straight; do

not lean forward or sideways. Adjust the

belt so the lap portion of the belt is worn

low across the pelvis, not across the waist.

Please refer to the “Seat Adjustment” sec-

WARNING

Failure to follow these instructions

may increase the risk of injury in a

crash.

• Only use an extender for the per-

son, vehicle and seating position it

was provided for.

• Do not use if open end of

extender’s buckle is within 152 mm

(6 inches) of center of occupant’s

body (See diagram).

• Remove and stow the extender

when it is not being used.

WARNING

This section of the owner’s manual

describes your SUZUKI’s SEAT BELT

PRETENSIONER SYSTEM. Please

read and follow ALL these instruc-

tions carefully to minimize your risk

of severe injury or death.

Supplemental Restraint System (air bags): 3, 9, 12

2-43

BEFORE DRIVING

79K21-03E

tion and the instructions and precautions

about the seat belts in this “Seat Belts and

Child Restraint Systems” section for details

on proper seat and seat belt adjustments.

Please note that the pretensioners along

with the front air bags will activate in

severe frontal collisions. Also, the preten-

sioners along with the side curtain air bags

will activate in severe rollovers. They are

not designed to activate in rear impacts,

side impacts, or minor frontal collisions.

The pretensioners can be activated only

once. If the pretensioners are activated

(that is, if the front air bags and/or the side

curtain air bags are activated), have the

pretensioner system serviced by an autho-

rized SUZUKI dealer as soon as possible.

If the “AIR BAG” light on the instrument

cluster does not blink or come on briefly

when the ignition switch is turned to the

“ON” position, stays on for more than 10

seconds, or comes on while driving, the

pretensioner system or the air bag system

may not work properly. Have both systems

inspected by an authorized SUZUKI dealer

as soon as possible.

Service on or around the pretensioner sys-

tem components or wiring must be per-

formed only by an authorized SUZUKI

dealer who is specially trained. Improper

service could result in unintended activa-

tion of pretensioners or could render the

pretensioner inoperative. Either of these

two conditions may result in personal

injury.

To prevent damage or unintended activa-

tion of the pretensioners, be sure the bat-

tery is disconnected and the ignition switch

has been in the “LOCK” position for at least

90 seconds before performing any electri-

cal service work on your SUZUKI. Do not

touch pretensioner system components or

wiring. The wires are wrapped with yellow

tape or yellow tubing, and the couplers are

yellow. When scrapping your SUZUKI, ask

your SUZUKI dealer, body repair shop or

scrap yard for assistance.

Supplemental Restraint

System (air bags)

54G022

Your vehicle has advanced front air bags

and side air bags for the driver and right

front passenger. Your vehicle also has side

curtain air bags.

WARNING

This section of the owner’s manual

describes the protection provided by

your SUZUKI’s SUPPLEMENTAL

RESTRAINT SYSTEM (air bags).

Please read and follow ALL these

instructions carefully to minimize

your risk of severe injury or death in

the event of a collision.

EXAMPLE

Supplemental Restraint System (air bags): 3, 9, 12

Before Driving -> Seat Belts and Child Restraint Systems for Your Suzuki Grand Vitara SUV Second Generation (2005-2015)

Related Topics

Popular Owner Manuals

Latest Owner Manuals