Get Inspection and Maintenance Guide for Suzuki Grand Vitara SUV Second Generation (2005-2015)

INSPECTION AND MAINTENANCE

79K21-03E

60G410

INSPECTION AND MAINTENANCE

Maintenance Schedule ....................................................... 7-2

Periodic Maintenance Schedule ........................................ 7-3

Maintenance Recommended under Severe Driving

Conditions ........................................................................... 7-7

Drive Belt ............................................................................. 7-9

Engine Oil and Filter ........................................................... 7-10

Engine Coolant .................................................................... 7-13

Air Cleaner ........................................................................... 7-16

Spark Plugs ......................................................................... 7-16

Gear Oil ................................................................................ 7-17

Clutch Pedal ........................................................................ 7-20

Automatic Transmission Fluid ........................................... 7-20

Brakes .................................................................................. 7-22

Steering Wheel .................................................................... 7-24

Tires ...................................................................................... 7-25

Battery .................................................................................. 7-36

Fuses .................................................................................... 7-36

Headlight Aiming ................................................................. 7-39

Bulb Replacement ............................................................... 7-40

Wiper Blades ....................................................................... 7-46

Windshield Washer Fluid ................................................... 7-49

Air Conditioning System .................................................... 7-49

7-1

INSPECTION AND MAINTENANCE

79K21-03E

60A187S

WARNING

You should take extreme care when

working on your vehicle to prevent

accidental injury. Here are a few pre-

cautions that you should be espe-

cially careful to observe:

• To prevent damage or unintended

inflation of the air bag system, be

sure the battery is disconnected

and the ignition switch has been in

the “LOCK” position for at least 90

seconds before performing any

electrical service work on your

SUZUKI. Do not touch air bag sys-

tem components or wires. The

wires are wrapped with yellow tape

or yellow tubing, and the couplers

are yellow for easy identification.

(Continued)

WARNING

(Continued)

• Do not leave the engine running in

garages or other confined areas.

• When the engine is running, keep

hands, clothing, tools and other

objects away from the moving fan

and fan belt.

• When it is necessary to do service

work with the engine running, make

sure that the parking brake is set

fully and the transmission is in

Neutral (for manual transmission

vehicles) or Park (for automatic

transmission vehicles).

• Do not touch ignition wires or other

ignition system parts when starting

the engine or when the engine is

running, or you could receive an

electric shock.

• Be careful not to touch a hot

engine, exhaust manifold and

pipes, muffler, radiator and water

hoses.

• Do not allow smoking, sparks or

flames around fuel or the battery.

Flammable fumes are present.

• Do not get under your vehicle if it is

supported only with the portable

jack provided in your vehicle.

(Continued)

WARNING

(Continued)

• Be careful not to cause accidental

short circuits between the positive

and negative battery terminals.

• Keep used oil, engine coolant and

other fluids away from children and

pets. Dispose of used fluids prop-

erly; never pour them on the

ground, into sewers, etc.

7-2

INSPECTION AND MAINTENANCE

79K21-03E

NOTICE (for U.S.A.)

Maintenance, replacement or repair of

the emission control devices and sys-

tems may be performed by any automo-

bile repair establishment or individual

using any part which has been certified

under the provisions in the Clean Air

Act sec. 207. (a) (2).

Maintenance Schedule

The following table shows the times when

you should perform regular maintenance

on your vehicle. This table shows in miles,

kilometers and months when you should

perform inspections, adjustments, lubrica-

tion and other services. These intervals

should be shortened if driving is usually

done under severe conditions (refer to

“Maintenance Recommended Under

Severe Driving Conditions”).

WARNING

SUZUKI recommends that mainte-

nance on items marked with an aster-

isk (*) be performed by your

authorized SUZUKI dealer or a quali-

fied service technician. If you are

qualified, you may perform mainte-

nance on the unmarked items by

referring to the instructions in this

section. If you are not sure whether

you can successfully complete any of

the unmarked maintenance jobs, ask

your authorized SUZUKI dealer to do

the maintenance for you.

CAUTION

Whenever it becomes necessary to

replace parts on your vehicle, it is

recommended that you use genuine

SUZUKI replacement parts or their

equivalent.

WARNING

The shock absorbers are filled with

high pressure gas. Never attempt to

disassemble them or throw them into

a fire. Avoid storing them near a

heater or heating device. When

scrapping the absorber, the gas must

be released from the absorber safely.

Ask your dealer for assistance.

Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10

7-3

INSPECTION AND MAINTENANCE

79K21-03E

Periodic Maintenance Schedule

R: Replace or change

I : Inspect, clean, adjust, lubricate or replace as necessary

#2: Be sure to perform the engine coolant level check under the daily inspection in “OPERATING YOUR VEHICLE” section.

If you replace the engine coolant other than the SUZUKI LLC: Super (Blue), follow the schedule of SUZUKI LLC: Standard (Green).

Interval: This interval should be judged by

odometer reading or months, whichever comes

first.

miles (x 1000) 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75

km (x 1000) 12.5 25 37.5 50 62.5 75 87.5 100 112.5 125

months 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75

ENGINE & EMISSION CONTROL

1. Drive belt

Inspect for damage – – – I – – – I – –

*2. Valve lash (clearance) (for 2.4 L engine) – – – – – – – I – –

3. Engine oil and oil filter R R R R R R R R R R

*4. Cooling system hoses and connections – – – I – – – I – –

5. Engine coolant SUZUKI LLC: Standard (Green) – – – R – – – R – –

SUZUKI LLC: Super (Blue) (#2) First time only: Replace at 150000 km (90000 miles) or 90 months

Second time and after: Replace every 75000 km (45000 miles) or 45 months

*6. Exhaust pipes and mountings – – – I – – – I&(R) – –

*7. EVAP canister Replace every 250000 km (150000 miles) or 180 months

*8. Emission-related hoses & tubes – – – – – – – I – –

9. Spark plugs – – – – – – – R – –

*10. Ignition coil (Plug cap) – – – I – – – I – –

*11. Fuel tank & cap – – – I – – – I – –

12. Air cleaner filter element – – – R – – – R – –

*13. Fuel filter – – – – – – – – – –

*14. Fuel lines and connections – – – I – – – I – –

*15. Canister air suction filter Replace every 250000 km (150000 miles) or 180 months

Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10

7-4

INSPECTION AND MAINTENANCE

79K21-03E

R: Replace or change

I : Inspect, clean, adjust, lubricate or replace as necessary

#1: Inspect at 250000 km (150000 miles) or 180 months.

#2: Be sure to perform the engine coolant level check under the daily inspection in “OPERATING YOUR VEHICLE” section.

If you replace the engine coolant other than the SUZUKI LLC: Super (Blue), follow the schedule of SUZUKI LLC: Standard (Green).

NOTE:

The maintenance services enclosed with rectangle are recommended maintenance items.

Item 6 (R) is applicable to the exhaust mounting rubber only.

Interval: This interval should be judged by

odometer reading or months, whichever comes

first.

miles (x 1000) 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150

km (x 1000) 137.5 150 162.5 175 187.5 200 212.5 225 237.5 250

months 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150

ENGINE & EMISSION CONTROL

1. Drive belt

Inspect for damage – I – – – I – – – I

*2. Valve lash (clearance) (for 2.4 L engine) – – – – – I – – – –

3. Engine oil and oil filter R R R R R R R R R R

*4. Cooling system hoses and connections – I – – – I – – – I

5. Engine coolant SUZUKI LLC: Standard (Green) – R – – – R – – – R

SUZUKI LLC: Super (Blue) (#2) First time only: Replace at 150000 km (90000 miles) or 90 months

Second time and after: Replace every 75000 km (45000 miles) or 45 months

*6. Exhaust pipes and mountings – I – – – I&(R) – – – I

*7. EVAP canister Replace every 250000 km (150000 miles) or 180 months

*8. Emission-related hoses & tubes – – – – – I – – – I

9. Spark plugs – – – – – R – – – –

*10. Ignition coil (Plug cap) – I – – – I – – – I

*11. Fuel tank & cap – I – – – I – – – I (#1)

12. Air cleaner filter element – R – – – R – – – R

*13. Fuel filter – – – – – – – – – R

*14. Fuel lines and connections – I – – – I – – – I (#1)

*15. Canister air suction filter Replace every 250000 km (150000 miles) or 180 months

The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform recom-

mended maintenance items enclosed with a rectangle will not nullify the emission warranty or limit recall liability prior to the completion

of the vehicle’s useful life. SUZUKI, however, urges that all recommended maintenance services be performed at the indicated inter-

vals and the maintenance recorded.

Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10

7-5

INSPECTION AND MAINTENANCE

79K21-03E

R: Replace or change

I : Inspect, clean, adjust, lubricate or replace as necessary

Interval: This interval should be judged by

odometer reading or months, whichever comes

first.

miles (x 1000) 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75

km (x 1000) 12.5 25 37.5 50 62.5 75 87.5 100 112.5 125

months 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75

CHASSIS AND BODY

1. Clutch (for manual transmission)

Pedal and fluid level – I – I – I – I – I

*2. Brake discs and pads (front, rear) – I – I – I – I – I

Brake drums and shoes (if equipped) – I – I – I – I – I

*3. Brake hoses and pipes – I – I – I – I – I

4. Brake fluid level check, *replacement – I – I – I – R – I

5. Brake pedal stroke check, *adjustment – I – I – I – I – I

6. Parking brake lever and *cable

Lever movement check, *adjustment – I – I – I – I – I

7. Tires (including tire rotation) I I I I I I I I I I

*8. Wheel discs I I I I I I I I I I

*9. Wheel bearings – I – *I – I – *I – I

*10. Suspension system – I – I – I – I – I

*11. Propeller shafts/Drive shafts – I – I – I – I – I

*12. Manual transmission oil I – – R – I – R – I

13. Automatic transmission (A/T) Fluid level – I – I – I – I – I

*Fluid change Replace every 175000 km (105000 miles)-----4-speed A/T or 5-speed A/T

*Fluid hose – – – – – I – – – –

*14. Transfer oil I – – I – I – R – I

*15. Differential & Extension (for 2WD) oil R – – I – I – I – I

16. Steering system

Steering wheel movement, *linkage I I I I I I I I I I

*17. Power steering (if equipped) I I I I I I I I I I

18. All Latches, Hinges and Locks I I I I I I I I I I

19. Air conditioner filter (if equipped) – I – R – I – R – I

Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10

7-6

INSPECTION AND MAINTENANCE

79K21-03E

R: Replace or change

I : Inspect, clean, adjust, lubricate or replace as necessary

NOTE:

This table shows the service schedule up to 250000 km (150000 miles).

Beyond 250000 km (150000 miles), perform the same services at the same intervals shown in the chart.

Beyond 250000 km (150000 miles), the maintenance services enclosed with a rectangle are required.

Item 9 *I - inspect for wear.

Interval: This interval should be judged by

odometer reading or months, whichever comes

first.

miles (x 1000) 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150

km (x 1000) 137.5 150 162.5 175 187.5 200 212.5 225 237.5 250

months 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150

CHASSIS AND BODY

1. Clutch (for manual transmission)

Pedal and fluid level – I – I – I – I – I

*2. Brake discs and pads (front, rear) – I – I – I – I – I

Brake drums and shoes (if equipped) – I – I – I – I – I

*3. Brake hoses and pipes – I – I – I – I – I

4. Brake fluid level check, *replacement – I – I – R – I – I

5. Brake pedal stroke check, *adjustment – I – I – I – I – I

6. Parking brake lever and *cable

Lever movement check, *adjustment – I – I – I – I – I

7. Tires (including tire rotation) I I I I I I I I I I

*8. Wheel discs I I I I I I I I I I

*9. Wheel bearings – *I – I – *I – I – I

*10. Suspension system – I – I – I – I – I

*11. Propeller shafts/Drive shafts – I – I – I – I – I

*12. Manual transmission oil – R – I – R – I – R

13. Automatic transmission (A/T) Fluid level – I – I – I – I – I

*Fluid change Replace every 175000 km (105000 miles)-----4-speed A/T or 5-speed A/T

*Fluid hose – I – – – – – I – –

*14. Transfer oil – I – I – R – I – I

*15. Differential & Extension (for 2WD) oil – I – I – I – I – I

16. Steering system

Steering wheel movement, *linkage I I I I I I I I I I

*17. Power steering (if equipped) I I I I I I I I I I

18. All Latches, Hinges and Locks I I I I I I I I I I

19. Air conditioner filter (if equipped) – R – I – R – I – R

Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10

7-7

INSPECTION AND MAINTENANCE

79K21-03E

Maintenance Recommended under Severe Driving Conditions

If the vehicle is usually used under the conditions corresponding to any severe condition code given below, it is recommended that appli-

cable maintenance operation be performed at the particular interval shown in the chart below.

Severe condition code

A – Repeated short trips

B – Driving on rough and/or muddy roads

C – Driving on dusty roads

D – Driving in extremely cold weather and/or on salted roads

E – Repeated short trips in extremely cold weather

H – Towing a trailer

Severe

Condition Code

Maintenance

Operation

Maintenance Interval

A – C D E H Engine oil and oil filter R

Every 5000 km (3000 miles)

or 3 months

A B – D – H Exhaust pipes and mountings I

Every 10000 km (6000 miles)

or 6 months

– – C – – – Air cleaner filter element *1

Every 5000 km (3000 miles)

or 3 months

Every 25000 km (15000 miles)

or 15 months

– – C – – – Canister air suction filter R

Every 100000 km (60000 miles)

or 60 months

ABC––H

Brake discs and pads (front)

Brake drums and shoes (rear)

Every 10000 km (6000 miles)

or 6 months

– B – D E H Propeller shafts/Drive shafts I

Every 10000 km (6000 miles)

or 6 months

– B – – E H Manual transmission oil R

Every 25000 km (15000 miles)

or 15 months

Maintenance Recommended under Severe Driving Condi-

tions: 1, 2, 3, 4, 5, 6, 9, 10

7-8

INSPECTION AND MAINTENANCE

79K21-03E

NOTE:

I – Inspect, clean, adjust, lubricate or replace as necessary

T – Tighten to the specified torque

R – Replace or change

L – Lubricate

*1 Inspect more frequently if the vehicle is used under dusty conditions.

*2 Clean more frequently if the air flow from the air conditioner decreases.

Severe

Condition Code

Maintenance

Operation

Maintenance Interval

– B – – E H Automatic transmission (A/T) fluid R

Every 25000 km (15000 miles)

or 15 months

– B – – E H Transfer, Differential and Extension oil R

Every 25000 km (15000 miles)

or 15 months

– B – – – – Bolts and nuts on suspension T

Every 10000 km (6000 miles)

or 6 months

– B C D – – Drive belt (Engine accessory) I

Every 25000 km (15000 miles)

or 15 months

– – C D – – Air conditioner filter element *2

Every 10000 km (6000 miles)

or 6 months

Every 50000 km (30000 miles)

or 30 months

Maintenance Recommended under Severe Driving Condi-

tions: 1, 2, 3, 4, 5, 6, 9, 10

7-9

INSPECTION AND MAINTENANCE

79K21-03E

Drive Belt

Check the accessory drive belt only for

damage. You do not need check it for ten-

sion as it has an automatic tensioner.

If you need to replace or adjust the belt

have it done by your SUZUKI dealer.

WARNING

When the engine is running, keep

hands, hair, clothing, tools, etc. away

from the moving fan and drive belts.

79K041

→: 100 N (22 lbs, 10 kg) press

ADB: Accessory drive belt

GE: Generator

PS: Power steering pump

AC: Air conditioner compressor

L4 2.4 L

ADB

V6 3.2 L

ADB

Drive Belt: 1, 2

Engine Oil and Filter: 1, 2

7-10

INSPECTION AND MAINTENANCE

79K21-03E

Engine Oil and Filter

Specified Oil

79K096

Use engine oil with the American Petro-

leum Institute Certified For Gasoline

Engines “Starburst” symbol.

We highly recommend you use SAE 5W-

30 oil.

Oil Level Check

Engine oil dipstick

52D030

It is important to keep the engine oil at the

correct level for proper lubrication of your

vehicle’s engine. Check the oil level with

the vehicle on a level surface. The oil level

indication may be inaccurate if the vehicle

is on a slope. The oil level should be

checked either before starting the engine

or at least 5 minutes after stopping the

engine.

52D084

The handle of the engine oil dipstick is col-

ored yellow for easy identification.

Pull out the oil dipstick, wipe oil off with a

clean cloth, insert the dipstick all the way

into the engine, then remove it again. The

oil on the stick should be between the

upper and lower limits shown on the stick.

If the oil level indication is near the lower

limit, add enough oil to raise the level to the

upper limit.

CAUTION

Failure to use the recommended oil

can result in engine damage.

“Starburst”

EXAMPLE

FULL

ADD

Engine Oil and Filter: 1, 2

7-11

INSPECTION AND MAINTENANCE

79K21-03E

Refilling

81A147

Remove the oil filler cap and pour oil slowly

through the filler hole to bring the oil level

to the upper limit on the dipstick. Be careful

not to overfill. Too much oil is almost as

bad as too little oil. After refilling, start the

engine and allow it to idle for about a

minute. Stop the engine, wait about 5 min-

utes and check the oil level again.

Changing Engine Oil and Filter

60G306

Drain the engine oil while the engine is still

warm.

1) Remove the oil filler cap.

2) Remove the engine under cover.

3) Place a drain pan under the drain plug.

4) Using a wrench, remove the drain plug

and drain out the engine oil.

5) Reinstall the drain plug and gasket.

Tighten the plug with a wrench to the

specified torque.

6) Reinstall the engine under cover.

CloseOpen

EXAMPLE

WARNING

The engine oil temperature may be

high enough to burn your fingers

when the drain plug is loosened. Wait

until the drain plug is cool enough to

touch with your bare hands.

EXAMPLE

WARNING

New and used oil and solvent can be

hazardous. Children and pets may be

harmed by swallowing new or used

oil or solvent. Repeated, prolonged

contact with used engine oil may

cause skin cancer. Brief contact with

used oil or solvent may irritate skin.

• Keep new and used oil and solvent

away from children and pets.

• Wear a long-sleeve shirt and water-

proof gloves.

• Wash with soap if oil or solvent

contacts your skin.

Tightening torque specification

35 Nm (25.3 lb-ft, 3.5 kg-m)

Engine Oil and Filter: 1, 2

7-12

INSPECTION AND MAINTENANCE

79K21-03E

Replace the Oil Filter

2.4 L engine

78K055

1) Using an oil filter wrench, turn the oil fil-

ter counterclockwise and remove it.

2) Using a clean rag, wipe off the mount-

ing surface on the engine where the

new filter will be seated.

3) Smear a little engine oil around the rub-

ber gasket of the new oil filter.

4) Screw on the new filter by hand until the

filter gasket contacts the mounting sur-

face.

54G093

(1) Oil filter

(2) 3/4 turn

5) Tighten the filter 3/4 turn from the point

of contact with the mounting surface (or

to the specified torque) using an oil filter

wrench.

6) Reinstall the engine under cover.

NOTE:

• When it is difficult to remove the oil filter,

we recommend you take your vehicle to

your SUZUKI dealer for oil filter replace-

ment.

• For 3.2 L engine, since special proce-

dures are required, we recommend you

take your vehicle to your SUZUKI dealer

for oil filter replacement.

Refill with Oil and Check for Leaks

1) Pour oil through the filler hole and

install the filler cap.

For the approximate capacity of the oil,

refer to the “Capacities” item in the

“SPECIFICATIONS” section.

2) Start the engine and look carefully for

leaks at the oil filter and drain plug. Run

the engine at various speeds for at least

5 minutes.

3) Stop the engine and wait about 5 min-

utes. Check the oil level again and add

oil if necessary. Check for leaks again.

CAUTION

To tighten the oil filter properly, it is

important to accurately identify the

position at which the filter gasket

first contacts the mounting surface.

EXAMPLE

Tightening torque specification

14 Nm (10.1 lb-ft, 1.4 kg-m)

CAUTION

To prevent oil leakage, make sure

that the oil filter is tight, but do not

overtighten it.

CAUTION

When replacing the oil filter, it is rec-

ommended that you use a genuine

SUZUKI replacement filter. If you use

an after-market filter, make sure it is

of equivalent quality and carefully fol-

low the manufacturer’s instructions

and precautions.

Engine Oil and Filter: 1, 2

7-13

INSPECTION AND MAINTENANCE

79K21-03E

83E010

Engine Coolant

64J151

60A208

Selection of Coolant

To maintain optimum performance and

durability of your engine, use SUZUKI

Genuine Coolant or equivalent.

NOTE:

If you replace the engine coolant other

than the SUZUKI LLC: Super (Blue), follow

the schedule of SUZUKI LLC: Standard

(Green). To see the detail of the mainte-

nance schedule, refer to “Periodic Mainte-

nance Schedule” in this section.

This type of coolant is best for your cooling

system as it:

• Helps maintain proper engine tempera-

ture.

• Gives proper protection against freezing

and boiling.

• Gives proper protection against corro-

sion and rust.

Failure to use the proper coolant can dam-

age your cooling system. Your authorized

SUZUKI dealer can help you select the

proper coolant.

CAUTION

Oil leaks from around the oil filter or

drain plug indicate incorrect installa-

tion or gasket damage. If you find any

leaks or are not sure that the filter

has been properly tightened, have

the vehicle inspected by your SUZUKI

dealer.

EXAMPLE

FULL

LOW

CAUTION

SUZUKI LLC: Super (Blue) coolant;

SUZUKI LLC: Super (Blue) coolant is

already diluted to the proper percent-

age. Do not dilute with distilled water

additionally. Doing so may result in

the possibility of freezing coolant

and/or overheating.

Gear Oil: 6, 10

7-14

INSPECTION AND MAINTENANCE

79K21-03E

Engine Coolant Level Check

Check the engine coolant level at the

reserve tank, not at the radiator. With the

engine cool, the engine coolant level

should be between the “FULL” and “LOW”

marks.

Adding Engine Coolant

If the engine coolant level is below the

“LOW” mark, more engine coolant should

be added. Remove the reserve tank cap

and add engine coolant until the reserve

tank level reaches the “FULL” mark. Never

fill the reserve tank above the “FULL” mark.

CAUTION

To avoid damaging your cooling sys-

tem:

• Always use a high quality ethylene

glycol base phosphate type coolant

diluted with distilled water at the

correct mixture concentration.

• Make sure that the proper mix is 50/

50 coolant to distilled water and in

no case higher than 70/30. Concen-

trations greater than 70/30 coolant

to distilled water will cause over-

heating conditions.

• Do not use straight coolant nor

plain water (except SUZUKI LLC:

Super (Blue)).

• Do not add extra inhibitors or addi-

tives. They may not be compatible

with your cooling system.

• Do not mix different types of base

coolants. Doing so may result in

accelerated seal wear and/or the

possibility of severe overheating

and extensive engine/automatic

transmission damage.

CAUTION

• The mixture you use should con-

tain 50% concentration of anti-

freeze.

• If the lowest ambient temperature

in your area is expected to be –35

°C (–31°F) or below, use higher

concentrations up to 60% following

the instructions on the antifreeze

container.

• When putting the cap on the

reserve tank, line up the arrow on

the cap and the arrow on the tank.

Failure to follow this can result in

coolant leakage.

WARNING

Engine coolant is harmful or fatal if

swallowed or inhaled. Do not drink

antifreeze or coolant solution. If swal-

lowed, do not induce vomiting. Imme-

diately contact a poison control

center or a physician. Avoid inhaling

mist or hot vapors; if inhaled, remove

to fresh air. If coolant gets in eyes,

flush eyes with water and seek medi-

cal attention. Wash thoroughly after

handling. Solution can be poisonous

to animals. Keep out of the reach of

children and animals.

Gear Oil: 6, 10

Automatic Transmission Fluid: 10

7-15

INSPECTION AND MAINTENANCE

79K21-03E

Engine Coolant Replacement

66J151

1) When the engine is cool, remove the

radiator cap by turning it slowly to the

left until a “stop” is felt. Do not press

down while turning the cap. Wait until

any pressure is released, then press

down on the cap and continue turning it

to the left.

66J191

2) Remove the reservoir by lifting it up,

and drain the reservoir completely.

64J191

3) Loosen the drain plug attached to the

lower part of the radiator and drain the

engine coolant into a suitable container.

4) Reinstall the reservoir and fill it with

engine coolant to the “FULL” line.

5) Tighten the drain plug on the radiator,

fill the radiator with engine coolant and

install the radiator cap.

6) After filling, let the engine idle for about

2 – 3 minutes to get rid of air in the

cooling system. Then, stop the engine.

7) Check the engine coolant level in the

radiator again. If the level has gone

down, add more engine coolant.

Open

WARNING

It is hazardous to remove the radiator

cap when the engine coolant temper-

ature is high, because scalding fluid

and steam may be blown out under

pressure. Wait until the engine cool-

ant temperature has lowered before

removing the cap.

CAUTION

The engine coolant must be replaced

with the vehicle on level ground.

EXAMPLE

Automatic Transmission Fluid: 10

Engine Coolant: 1, 2

7-16

INSPECTION AND MAINTENANCE

79K21-03E

Air Cleaner

66J167

If the air cleaner is clogged with dust, there

will be greater intake resistance, resulting

in decreased power output and increased

fuel consumption.

Check and clean periodically according to

the following procedure:

1) Take off the air cleaner case cover.

Remove the element from the air

cleaner case cover.

2) This air cleaner element is of dry type.

Remember that it needs cleaning

according to the following method.

3) Blow off dust on cleaner element by

compressed air from inside the ele-

ment, or replace the element as neces-

sary.

Spark Plugs

78K056

NOTE:

For 3.2 L engine, to approach the spark

plugs, you need to remove the bolts shown

in the illustration.

EXAMPLE

CAUTION

The air cleaner element should be

replaced every 50000 km (30000

miles). More frequent replacement is

necessary when you drive under

dusty conditions.

Engine Coolant: 1, 2

7-17

INSPECTION AND MAINTENANCE

79K21-03E

65D434

You should inspect spark plugs periodically

for carbon deposits. When carbon accu-

mulates on a spark plug, a strong spark

may not be produced. Remove carbon

deposits with a wire or pin and adjust the

spark plug gap.

To access the spark plugs:

1) Remove the engine cover.

2) Disconnect the coupler (1) while push-

ing the release lever.

3) Remove the bolt.

4) Pull the ignition coil out.

80G093

Gear Oil

Specified Gear Oil

When replacing gear oil, use gear oil with

the appropriate viscosity and grade as

shown in the charts below. We highly rec-

ommend you use SAE 75W-90 gear oil

(SAE 80W-90 for front differential oil, rear

differential oil and transfer gear oil).

Transmission/Extension case

54G095

Differential/Transfer case

65D594

CAUTION

When replacing spark plugs, you

should use the brand and type speci-

fied for your vehicle. For the speci-

fied plugs, refer to the

“SPECIFICATIONS” section at the

end of this book. If you wish to use a

brand of spark plug other than the

specified plugs, consult your SUZUKI

dealer.

1.0 – 1.1 mm

(0.039 – 0.043 in.)

Engine Coolant: 1, 2

Windshield Washer Fluid: 3

7-18

INSPECTION AND MAINTENANCE

79K21-03E

Manual transmission

52D087

Transfer case

66J005

(1) Oil filler and level plug

(2) Oil drain plug

Extension case (2WD)

66J165

(1) Oil filler and level plug

(2) Oil drain plug

API GRADE

Transmission/

Extension case

GL-4

Transfer case

GL-5

(Hypoid gear oil)

Differential

Front

Rear

(1)

(2)

(1)

Windshield Washer Fluid: 3

Air Cleaner: 1, 2

7-19

INSPECTION AND MAINTENANCE

79K21-03E

Front differential

79K133

Rear differential

79K134

(1) Oil filler and level plug

(2) Oil drain plug

Gear Oil Level Check

The manual transmission, transfer gears,

extension case and differentials (front and

rear) are lubricated with gear oil. To check

the gear oil level in any of the above loca-

tions, use the following procedure:

1) Park the vehicle on a level surface. Set

parking brake and stop the engine.

2) Remove the oil filler plug (1).

3) Check the inside of the hole with your

finger. If the oil level comes up to the

bottom of the plug hole, the oil level is

correct. If so, reinstall the plug.

4) If the oil level is low, add gear oil

through the filler plug hole (1) until the

oil level reaches the bottom of the filler

hole, then reinstall the plug.

Gear Oil Replacement

To change the gear oil in the manual trans-

mission, transfer case, extension case or

differential(s), use the following procedure:

1) Remove the oil filler plug (1).

2) Remove the drain plug (2), drain the oil

and reinstall the drain plug.

3) Pour new gear oil of the specified type

through the filler hole until the oil level

reaches the bottom of the filler hole.

4) Reinstall the filler plug.

(1)

(2)

(1)

(2)

WARNING

After driving the vehicle, gear oil tem-

perature may be high enough to burn

you. Wait until the oil filler plug is

cool enough to touch with your bare

hands before inspecting or replacing

gear oil.

CAUTION

When tightening these plugs, apply

sealing compound “SUZUKI Bond

No. 1217G” or equivalent to the plug

threads to prevent oil leakage and

tighten them to the specified torque

shown below.

Spark Plugs: 1, 2

Brakes: 6

7-20

INSPECTION AND MAINTENANCE

79K21-03E

Tightening torque

Clutch Pedal

64J154

Check the clutch pedal for smooth opera-

tion and clutch fluid level from time to time.

If clutch dragging is felt with the pedal fully

depressed, have the clutch inspected by

your SUZUKI dealer. If the clutch fluid level

is near the “MIN” line, fill it up to the “MAX”

line with DOT3 brake fluid.

Automatic Transmission

Fluid

Specified Fluid

Use an automatic transmission fluid

SUZUKI ATF 3317 or Mobil ATF 3309.

Fluid Level Check

You must check the fluid level with the

automatic transmission fluid at normal

operating temperature.

To check the fluid level:

1) To warm up the transmission fluid, drive

the vehicle or idle the engine until the

temperature gauge indicates normal

operating temperature.

2) Then drive for ten more minutes.

Oil Filler

Plug

Oil Drain

Plug

Manual

transmission

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

Tra nsfer

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

Extension

case

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

Front

differential

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

Rear

differential

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

23 Nm

(17.0 lb-ft)

(2.3 kg-m)

CAUTION

Driving with too much or too little

fluid can damage the transmission.

CAUTION

Be sure to use the specified auto-

matic transmission fluid. Using auto-

matic transmission fluid other than

SUZUKI ATF 3317 or Mobil ATF 3309

may damage the automatic transmis-

sion of your vehicle.

Brakes: 6

7-21

INSPECTION AND MAINTENANCE

79K21-03E

NOTE:

Do not check the fluid level if you have just

driven the vehicle for a long time at high

speed, if you have driven in city traffic in

hot weather, or if the vehicle has been pull-

ing a trailer. Wait until the fluid cools down

(about 30 minutes), or the fluid level indica-

tion will not be correct.

3) Park your vehicle on level ground.

4) Apply the parking brake and then start

the engine in “P” (Park). Let it idle for

two minutes and keep it running during

the fluid level check.

5) With your foot on the brake pedal, move

the gearshift lever through each gear,

pausing for about three seconds in

each range. Then move it back to the

“P” (Park) position.

60A205

The handle of the A/T fluid dipstick is col-

ored red for easy identification.

65D109

6) Remove the dipstick, clean it and push

it back in until the cap seats. Pull out

the dipstick and read the fluid level.

The fluid level should be between the

two marks in the “HOT” range on the

dipstick.

7) Add just enough specified fluid through

the dipstick hole to fill the transmission

to the proper level.

Changing Oil

Since special procedures, materials and

tools are required to change the automatic

transmission oil, it is recommended that

you trust this job to your authorized

SUZUKI dealer.

WARNING

Be sure to depress the brake pedal

when moving the gearshift lever, or

the vehicle can move suddenly.

EXAMPLE

FULL HOT

LOW HOT

CAUTION

After checking or adding oil, be sure

to insert the dipstick securely.

Brakes: 6

7-22

INSPECTION AND MAINTENANCE

79K21-03E

Brakes

Brake Fluid

64J154

Check the brake fluid level by looking at

the reservoir in the engine compartment.

Check that the fluid level is between the

“MAX” and “MIN” lines. If the brake fluid

level is near the “MIN” line, fill it up to the

“MAX” line with DOT3 brake fluid.

65D477

WARNING

Failure to follow the guidelines below

can result in personal injury or seri-

ous damage to the brake system.

• If the brake fluid in the reservoir

drops below a certain level, the

brake warning light on the instru-

ment panel will come on (the

engine must be running with the

parking brake fully disengaged.)

Should the light come on, immedi-

ately ask your SUZUKI dealer to

inspect the brake system.

• A rapid fluid loss indicates a leak in

the brake system which should be

inspected by your SUZUKI dealer

immediately.

• Brake fluid can harm your eyes and

damage painted surfaces. Use cau-

tion when refilling the reservoir.

(Continued)

WARNING

(Continued)

• Do not use any fluid other than

DOT3 brake fluid. Do not use

reclaimed fluid or fluid that has

been stored in old or open contain-

ers. It is essential that foreign parti-

cles and other liquids are kept out

of the brake fluid reservoir.

WARNING

Brake fluid is harmful or fatal if swal-

lowed, and harmful if it comes in con-

tact with skin or eyes. If swallowed,

do not induce vomiting. Immediately

contact a poison control center or a

physician. If brake fluid gets in eyes,

flush eyes with water and seek medi-

cal attention. Wash thoroughly after

handling. Solution can be poisonous

to animals. Keep out of the reach of

children and animals.

CAUTION

The brake fluid should be replaced

according to the maintenance sched-

ule. Have the brake fluid replaced by

your SUZUKI dealer.

Steering Wheel: 6

Clutch Pedal: 6

7-23

INSPECTION AND MAINTENANCE

79K21-03E

NOTE:

With disc brakes, the fluid level can be

expected to gradually fall as the brake

pads wear.

Brake Pedal

79K138

With the engine running and the parking

brake set, measure the distance between

the brake pedal and floor carpet when the

pedal is depressed with approximately 300

N (66 lbs, 30 kg) of force. The minimum

distance required is as specified. Since

your vehicle’s brake system is self-adjust-

ing, there is no need for pedal adjustment.

If the pedal to floor carpet distance as

measured above is less than the minimum

distance required, have your vehicle

inspected by your SUZUKI dealer.

NOTE:

When measuring the distance between the

brake pedal and floor wall, push in the floor

carpet as far as it goes and measure the

distance between the carpet surface and

the brake pedal.

60G104

Pedal to floor carpet minimum distance

“a”

80 mm (3.1 in.)

“a”

Floor carpet

WARNING

If you experience any of the following

problems with your vehicle’s brake

system, have the vehicle inspected

immediately by your SUZUKI dealer.

• Poor braking performance

• Uneven braking (brakes not work-

ing uniformly on all wheels.)

• Excessive pedal travel

• Brake dragging

• Excessive noise

• (Except ABS equipped vehicle)

Pedal pulsation (pedal pulsates

when pressed for braking.)

Tires: 6

7-24

INSPECTION AND MAINTENANCE

79K21-03E

Parking Brake Lever

60A226

Check the parking brake for proper adjust-

ment by counting the number of clicks

made by the ratchet teeth as you slowly

pull up on the parking brake lever to the

point of full engagement. The parking

brake lever should stop between the speci-

fied ratchet teeth and the rear wheels

should be securely locked. If the parking

brake is not properly adjusted or the

brakes drag after the lever has been fully

released, have the parking brake inspected

and/or adjusted by your SUZUKI dealer.

Steering Wheel

78K080

Check the play of the steering wheel by

gently turning it from left to right and mea-

suring the distance that it moves before

you feel slight resistance. The play should

be between the specified values. Check

that the steering wheel turns easily and

smoothly without rattling by turning it all the

way to the right and to the left while driving

very slowly in an open area. If the amount

of free play is outside the specification or

you find anything else to be wrong, an

inspection must be performed by your

SUZUKI dealer.

Power Steering (if equipped)

64J155

(1) UPPER

(2) LOWER

Check the steering box case, vane pump

and hose connections for leaks or damage.

Power Steering Fluid

Check the fluid level by looking at the res-

ervoir in the engine compartment when the

fluid is cold (about room temperature).

Check that the fluid level is between the (1)

and (2) lines. If the fluid level is near the (2)

line, fill it up to the (1) line with an auto-

matic transmission fluid equivalent to ATF

DEXRON

-II (Esso JWS 2326) or

DEXRON

-III. Do not overfill.

Ratchet tooth specification “b”

5th – 7th

200 N (44 lbs, 20 kg)

“b”

EXAMPLE

Steering wheel play “c”

0 – 30 mm (0.0 – 1.2 in.)

“c”

EXAMPLE

(1)

(2)

Tires: 6

7-25

INSPECTION AND MAINTENANCE

79K21-03E

Tires

For safe operation of your vehicle, it is

important that the tires be the correct

type and size, in good condition, and

properly inflated. Be sure to follow the

requirements and recommendations in

this section.

Tire Sidewall Labeling

Useful information about a tire is

molded into its sidewall. The example

below shows a typical passenger car

tire.

Typical Passenger Car Tire Sidewall

67D027

A. Tire Manufacturer

The name of the tire manufacturer

is shown here.

B. Tire Name/Model

The tire name or model is shown

here.

C. Tire Size

The tire size code is a combina-

tion of letters and numbers used

to define a particular tire’s width,

height, aspect ratio, construction

type, and service description. See

the “Tire Size” explanation later in

this section for more details.

D. U.S. DOT Tire Identification Num-

ber

The Department of Transportation

(DOT) marking indicates that the

tire is in compliance with the U.S.

Department of Transportation

Motor Vehicle Safety Standards.

The letters and numbers following

the DOT marking is the Tire Iden-

tification Number (TIN). The TIN

identifies the tire manufacturer

and plant, tire size, and date the

tire was manufactured.

E. Uniform Tire Quality Grading

(UTQG)

Tire manufacturers are required to

grade tires based on three perfor-

mance factors: treadwear, traction

and temperature resistance.

Refer to the “Uniform Tire Quality

Grading” section for more details.

F. Load Rating

Load rating is the maximum

weight a tire is designed to sup-

port in normal service.

G. Max Inflation Pressure

Max inflation pressure is the max-

imum inflation pressure a tire is

designed for.

H. Tire Ply Material

These tire markings describe the

type of cord and number of plies

in the sidewall and under the

tread.

I. Load Index and Speed Rating

The two- or three-digit number is

the tire’s load index, the maximum

load a tire can carry at the speed

indicated by its speed symbol at

the maximum inflation pressure.

The higher the number is, the

greater the load carrying capacity.

The letter symbol denotes the

speed at which a tire is designed

to be driven for extended periods

of time. (Ratings are listed below.)

EXAMPLE

Tires: 6

7-26

INSPECTION AND MAINTENANCE

79K21-03E

*The letters ZR may be used on tires

with a maximum speed capability over

149 mph and will always be used on

tires with a maximum speed capability

over 186 mph.

J. M+S Marking

This marking indicates the tire

has some mud and snow capabili-

ties and is designed for all-season

use.

Tire Size

The following illustration shows an

example of a typical passenger car tire

size.

67D028

A. Tire Type

This letter code indicates the pri-

mary intended use of the tire. The

letter “P” identifies a tire primarily

intended for use on a passenger

vehicle.

B. Tire Width

This three-digit number indicates

the tire section width in millime-

ters from sidewall to sidewall.

C. Aspect Ratio

This two-digit number represents

the tire section height divided by

the tire section width.

D. Construction Code

This letter code is used to indicate

the type of ply construction in the

tire. The letter “R” means radial

ply tire construction, the letter “D”

means diagonal or bias ply con-

struction, and the letter “B” means

belted-bias ply construction.

E. Rim Diameter

This two-digit number is the wheel

or rim diameter in inches.

Letter Rating Speed Rating

Q99 mph

R 106 mph

S 112 mph

T 118 mph

U 124 mph

H 130 mph

V 149 mph

W 168 mph*

Y 186 mph*

A B C D E

EXAMPLE

WARNING

Your SUZUKI is equipped with

tires which are all the same type

and size. This is important to

ensure proper steering and han-

dling of the vehicle. Never mix

tires of different size or type on

the four wheels of your vehicle.

Mixing tires could cause you to

lose control while driving which

may lead to an accident. The size

and type of tires used should be

only those approved by SUZUKI

Motor Corporation as standard or

optional equipment for your vehi-

cle.

Tires: 6

7-27

INSPECTION AND MAINTENANCE

79K21-03E

Tire Inflation Pressure

Tire inflation pressure should be

checked when the tire is cold. “Cold

tire inflation pressure” is the pressure

in a tire that has been driven less than

1 mile (1.6 km) or has been standing

for three hours or more.

54G307

The front, rear and spare tire pressure

specifications for your vehicle are

shown below and are listed on the Tire

and Loading Information Label, which

is located on the driver’s door lock pil-

lar. The Tire and Loading Information

Label contains the following informa-

tion:

• Seating Capacity

• Maximum Allowed Combined

Weight of Occupants and Cargo

• Original Tire Size

• Recommended Cold Tire Inflation

Pressure of Original Tires

NOTE:

The tire inflation pressure will change

due to changes in atmospheric pres-

sure, temperature or tire temperature

when driving. To reduce the chance

that the low tire pressure warning light

will come on due to normal changes in

temperature and atmospheric pres-

sure, it is important to check and

adjust the tire pressures when the tires

are cold. Tires that appear to be at the

specified pressure when checked after

driving, when the tires are warm, could

have pressure below the specification

when the tires cool down. Also, tires

that are inflated to the specified pres-

sure in a warm garage may have pres-

sure below the specification when the

vehicle is driven outside in very cold

temperature. If you adjust the tire

pressure in a garage that is warmer

than the outside temperature, you

should add 1 psi to the recommended

cold tire inflation pressure for every

10°F difference between garage tem-

perature and outside temperature.

Measuring air pressure

Use the following steps to achieve

proper tire inflation:

1) Identify the recommended tire pres-

sure on the vehicle’s Tire and Load-

ing Information Label or in the

owner’s manual.

2) Remove the valve cap from the tire

valve stem.

3) Using a reliable pressure gauge,

measure the tire inflation pressure

by pressing the tire gauge firmly

onto the valve to get a pressure

measurement. Remember that

inflation pressures should be

checked when the tires are “cold”,

meaning before they have been

driven one mile or after sitting for

three hours or more allowing the

tire to cool to ambient air tempera-

ture.

4) If the air pressure is too high, slowly

release the air by pressing on the

tire valve stem with the edge of the

Recommended Cold Tire Inflation

Pressures

Front Tires

230 kPa

33 psi

Rear Tires

230 kPa

33 psi

Spare

230 kPa

33 psi

Tires: 6

7-28

INSPECTION AND MAINTENANCE

79K21-03E

tire gauge until you reach the cor-

rect pressure.

5) If the air pressure is too low, fill the

tire with air at a service station until

it reaches the recommended pres-

sure.

6) Make sure all tires have the same

air pressure (unless the owner’s

manual indicates otherwise).

Tire Inspection

Inspect your vehicle’s tires at least

once a month by performing the fol-

lowing checks:

1) Measure the air pressure with a tire

gauge. Adjust the pressure if nec-

essary. Remember to check the

spare tire, too. Refer to the “Mea-

suring Air Pressure” section.

54G136

(1) Tread wear indicator

(2) Indicator location mark

2) Check that the depth of the tread

groove is more than 1.6 mm (0.06

in.). To help you check this, the tires

have molded-in tread wear indica-

tors in the grooves. When the indi-

cators appear on the tread surface,

the remaining depth of the tread is

WARNING

• Air pressures should be

checked when the tires are cold

or you may get inaccurate read-

ings.

• Check the inflation pressure

from time to time while inflating

the tire gradually, until the spec-

ified pressure is obtained.

(Continued)

WARNING

(Continued)

• Never underinflate or overin-

flate the tires.

Underinflation can cause

unusual handling characteris-

tics or can cause the rim to slip

on the tire bead, resulting in an

accident or damage to the tire

or rim.

Underinflation can also cause

tires to overheat, leading to tire

failure.

Overinflation can cause the tire

to burst, resulting in personal

injury.

Overinflation can also cause

unusual handling characteris-

tics which may result in an acci-

dent.

Tires: 6

7-29

INSPECTION AND MAINTENANCE

79K21-03E

1.6 mm (0.06 in.) or less and the

tire should be replaced.

3) Check for abnormal wear, cracks

and damage. Any tires with cracks

or other damage should be

replaced. If any tires show abnor-

mal wear, have them inspected by

your SUZUKI dealer.

4) Check for loose wheel nuts.

5) Check that there are no nails,

stones or other objects sticking into

the tires.

WARNING

Hitting curbs and running over

rocks can damage tires and affect

wheel alignment. Be sure to have

tires and wheel alignment

checked periodically by your

SUZUKI dealer.

WARNING

Your SUZUKI is equipped with

tires which are all the same type

and size. This is important to

ensure proper steering and han-

dling of the vehicle. Never mix

tires of different size or type on

the four wheels of your vehicle.

The size and type of tires used

should be only those approved by

SUZUKI Motor Corporation as

standard or optional equipment

for your vehicle.

WARNING

Replacing the wheels and tires

equipped on your vehicle with

certain combinations of aftermar-

ket wheels and tires can signifi-

cantly change the steering and

handling characteristics of your

vehicle. Oversized tires may also

rub against the fender over

bumps, causing vehicle damage

or tire failure. Therefore, use only

those wheel and tire combina-

tions approved by SUZUKI Motor

Corporation as standard or

optional equipment for your vehi-

cle. For information regarding the

specified tires, refer to the Tire

Information Label located on the

driver’s side door pillar or the

“SPECIFICATIONS” section.

CAUTION

Replacing the original tires with

tires of a different size may result

in false speedometer or odometer

readings. Check with your

SUZUKI dealer before purchas-

ing replacement tires that differ in

size from the original tires.

Tires: 6

7-30

INSPECTION AND MAINTENANCE

79K21-03E

Uniform Tire Quality Grading

The U.S. National Highway Traffic

Safety Administration has developed a

grading system for evaluating the per-

formance of passenger car tires. The

following information will help you

understand the grading system, which

applies to vehicles sold in the U.S.

Consult your SUZUKI dealer or tire

retailer for help in choosing the correct

replacement tires for your vehicle.

Quality grades can be found where

applicable on the tire sidewall between

tread shoulder and maximum section

width. For example:

Treadwear 200 Traction AA Tempera-

ture A

DOT Quality Grades

Treadwear

Traction AA A B C

Temperature A B C

All Passenger Car Tires Must Conform

To Federal Safety Requirements in

Addition To These Grades

Treadwear

The treadwear grade is a comparative

rating based on the wear rate of the

tire when tested under controlled con-

ditions on a specified government test

course. For example, a tire graded 150

would wear one and one-half (1 1/2)

times as well on the government

course as a tire graded 100. The rela-

tive performance of tires depends

upon the actual conditions of their use,

however and may depart significantly

from the norm due to variations in driv-

ing habits, service practices and differ-

ences in road characteristics and

climate.

Traction – AA, A, B, C

The traction grades, from highest to

lowest, are AA, A, B and C. Those

grades represent the tire’s ability to

stop on wet pavement as measured

under controlled conditions on speci-

fied government test surfaces of

asphalt and concrete. A tire marked C

may have poor traction performance.

Temperature – A, B, C

The temperature grades are A (the

highest), B and C, representing the

tire’s resistance to the generation of

heat and its ability to dissipate heat

when tested under controlled condi-

tions on a specified indoor laboratory

test wheel. Sustained high tempera-

ture can cause the material of the tire

to degenerate and reduce tire life, and

excessive temperature can lead to

sudden tire failure. The grade C corre-

sponds to a level of performance

which all passenger car tires must

meet under the Federal Motor Vehicle

Safety Standard No. 109. Grades B

and A represent higher levels of per-

formance on the laboratory test wheel

than the minimum required by law.

WARNING

The traction grade assigned to

this tire is based on straight-

ahead braking traction tests, and

does not include acceleration,

cornering, hydroplaning or peak

traction characteristics.

WARNING

The temperature grade for this

tire is established for a tire that is

properly inflated and not over-

loaded. Excessive speed, under-

inflation or excessive loading,

either separately or in combina-

tion, can cause heat buildup and

possible tire failure.

Tires: 6

7-31

INSPECTION AND MAINTENANCE

79K21-03E

Tire Rotation

4-tire rotation

65D459

To avoid uneven wear of your tires and

to prolong their life, rotate the tires as

illustrated. Tires should be rotated as

recommended in the periodic mainte-

nance schedule. After rotation, adjust

front and rear tire pressures to the

specification listed on your vehicle’s

Tire and Loading Information Label.

WARNING

Rust or dirt on a wheel, or on the

parts to which it is fastened, can

make wheel nuts become loose

after a time. The wheel could

come off and cause an accident.

When you change a wheel,

remove any rust or dirt from

places where the wheel attaches

to the vehicle. In an emergency,

you can use a cloth or a paper

towel to do this; but be sure to

use a scraper or wire brush later,

if you need to, to get all the rust

or dirt off.

WARNING

Vehicle equipped with P225/

65R17 tires have a spare wheel

and tire that are a different size

than the wheels and tires on the

vehicle. The spare wheel and tire

on these vehicles are intended for

temporary emergency use only.

The wheel is painted yellow to

remind you that the wheel and

tire are for temporary use only.

Continuous use of this spare can

result in tire failure and loss of

control. Always observe these

precautions when using this

spare:

• Be aware that your vehicle will

handle differently with this tem-

porary spare.

• Do not exceed 80 km/h (50 mph)

speed.

• Replace the temporary spare

with a standard tire and wheel

as soon as possible.

• Do not operate your vehicle in

“4H LOCK” or “4L LOCK” with

this temporary spare.

(Continued)

Tires: 6

7-32

INSPECTION AND MAINTENANCE

79K21-03E

Snow Tires

Your vehicle is equipped with all-sea-

son tires which are designed for use in

summer and most winter conditions.

For improved traction in severe winter

conditions, SUZUKI recommends

mounting radial snow tires on all four

wheels. Snow tires must be the same

size as the standard tires. Also be sure

to use the tires of the same type and

brand on all four wheels of your vehi-

cle.

GLOSSARY OF TIRE TERMI-

NOLOGY

Accessory Weight – the combined

weight (in excess of those standard

items which may be replaced) of auto-

matic transmission, power steering,

power brakes, power windows, power

seats, radio, and heater, to the extent

that these items are available as fac-

tory-installed equipment (whether

installed or not).

Cold Tire Inflation Pressure – the pres-

sure in a tire that has been driven less

than 1 mile or has been standing for

three hours or more.

Curb Weight – the weight of a motor

vehicle with standard equipment

including the maximum capacity of

fuel, oil, and coolant, and, if so

equipped, air conditioning and addi-

tional weight optional engine.

Intended Outboard Sidewall – (1) the

sidewall that contains a whitewall,

bears white lettering or bears manu-

facturer, brand, and/or model name

molding that is higher or deeper than

the same molding on the other side-

wall of the tire, or (2) the outward fac-

ing sidewall of an asymmetrical tire

that has a particular side that must

always face outward when mounted

on a vehicle.

Maximum Inflation Pressure – the

maximum cold inflation pressure a tire

is designed to support in normal ser-

vice.

Maximum Loaded Vehicle Weight –

the sum of curb weight, accessory

weight, vehicle capacity weight (total

load capacity), and production options

weight.

Normal Occupant Weight – 68 kilo-

grams times the number of occupants

specified in the second column of

Table 1 (shown below).

Occupant distribution – distribution of

occupants in a vehicle as specified in

the third column of Table 1 (shown

below).

Production Options Weight – the com-

bined weight of those installed regular

production options weighing over 2.3

kilograms in excess of those standard

items which they replace, not previ-

ously considered in curb weight or

accessory weight, including heavy

duty brakes, ride levelers, roof rack,

heavy duty battery, and special trim.

WARNING

(Continued)

• Do not use tire chains on the

spare tire. If you must use tire

chains, rearrange the wheels so

standard tires and wheels are

fitted to the rear axle.

• Replace the spare tire with a

new one as soon as the tread

wear indicator appears.

• When replacing the spare tire,

use a replacement tire with the

exact same size and construc-

tion.

Battery: 9

Fuses: 7

7-33

INSPECTION AND MAINTENANCE

79K21-03E

Recommended Inflation Pressure –

the cold tire inflation pressure recom-

mended by a manufacturer.

Rim – metal support for a tire or tire

and tube assembly upon which the tire

beads are seated.

Vehicle Capacity Weight – the rated

cargo and luggage load plus 68 kilo-

grams (150 lbs) times the vehicle’s

designated seating capacity.

Vehicle Maximum Load on the Tire –

the load on an individual tire that is

determined by distributing to each axle

its share of the maximum loaded vehi-

cle weight and dividing by two.

Vehicle Normal Load on the Tire – the

load on an individual tire that is deter-

mined by distributing to each axle its

share of the curb weight, accessory

weight, and normal occupant weight

(distributed in accordance with Table 1

shown below) and dividing by 2.

TABLE 1 – Occupant Loading and

Distribution For Vehicle Normal

Load For Various Designated Seat-

ing Capacities

Vehicle Loading

Your vehicle was designed for specific

load capacities. The load capacities of

your vehicle are indicated by the

Gross Vehicle Weight Rating (GVWR),

the Gross Axle Weight Rating (GAWR,

front and rear), and the total load

capacity, the seating capacity, and the

cargo load capacity. The GVWR and

GAWR (front and rear) are listed on

the Safety Certification Label which is

located below the driver’s side door

latch striker. The total load capacity

and seating capacity are listed on the

Tire and Loading Information Label

which is located below the Safety Cer-

tification Label. The cargo load capac-

ity can be determined as described

below.

Cargo Load Capacity – Maximum

weight of cargo and luggage that the

vehicle can safely carry. Cargo load

capacity is the difference between the

total load capacity of the vehicle and

the total combined weight of all vehicle

occupants. Refer to “Steps for Deter-

mining Correct Load Limit” for details

on how to determine cargo load

capacity.

GVWR – Maximum permissible overall

weight of the fully loaded vehicle

(including all the occupants, accesso-

ries and cargo plus the trailer tongue

weight if towing a trailer).

GAWR – (Front and Rear) Maximum

permissible weight on an individual

axle.

Seating Capacity – Maximum number

of occupants the vehicle is designed to

carry.

NOTE:

Even though the number of occupants

is within the seating capacity, you still

must make sure that you do not

Designated

seating

capacity,

number of

occupants

Vehicle

normal

load,

number of

occupants

Occupant

distribution

in a

normally

loaded

vehicle

2 through 4 2 2 in front

5 through 10 3 2 in front,

1 in sec-

ond seat

Fuses: 7

7-34

INSPECTION AND MAINTENANCE

79K21-03E

exceed the total load capacity of the

vehicle.

Total Load Capacity – Maximum per-

missible weight a vehicle can carry

including the weight of all the occu-

pants, accessories, cargo, plus trailer

tongue weight (if towing a trailer).

The weight of any accessories already

installed on your vehicle at the time of

purchase, or that you or the dealer

install after purchase, must be sub-

tracted from the total load capacity to

determine how much capacity remains

available for occupants, cargo, and

trailer tongue weight (if towing a

trailer). Contact your dealer for further

information.

Actual weight of the loaded vehicle

and actual loads at the front and rear

axles can only be determined by

weighing the vehicle using a vehicle

scale. To measure the weight and

load, try making your vehicle to a high-

way weighing station, shipping com-

pany or inspection station for trucks,

etc. Compare these weights to the

GVWR and GAWR (front and rear)

listed on the Safety Certification Label.

If the gross vehicle weight or the load

on either axle exceeds these ratings,

you must remove enough weight to

bring the load down to the rated

capacity.

Steps for Determining Correct Load

Limit

1) Locate the statement “The com-

bined weight of occupants and

cargo should never exceed XXX kg

or XXX lbs” on your vehicle’s plac-

ard.

2) Determine the combined weight of

the driver and passengers that will

be riding in your vehicle.

3) Subtract the combined weight of

the driver and passengers from

XXX kg or XXX lbs.

4) The resulting figure equals the

available amount of cargo and lug-

gage load capacity. For example, if

the “XXX” amount equals 1400 lbs

and there will be five 150 lb passen-

WARNING

Never overload your vehicle.

Overloading your vehicle can

cause damage to your tires and

lead to poor steering and braking

which can result in an accident.

The gross vehicle weight (sum of

the weights of the loaded vehicle,

driver and passengers) must

never exceed the Gross Vehicle

Weight Rating (GVWR) listed on

the Safety Certification Label. In

addition, never distribute a load

so that the weight on either the

front or rear axle exceeds the

Gross Axle Weight Rating

(GAWR) listed on the Safety Certi-

fication Label.

WARNING

• Always distribute cargo evenly.

• To avoid personal injury or

damage to your vehicle, always

secure cargo to prevent it from

shifting if the vehicle moves

suddenly.

• Place heavier objects on the

floor and as far forward in the

cargo area as possible. Never

pile cargo higher than the top of

the seatbacks.

Fuses: 7

7-35

INSPECTION AND MAINTENANCE

79K21-03E

gers in your vehicle, the amount of

available cargo and luggage load

capacity is 650 lbs (1400 – 750 (5 x

150) = 650 lbs).

5) Determine the combined weight of

luggage and cargo being loaded on

the vehicle. That weight may not

safely exceed the available cargo

and luggage load capacity calcu-

lated in Step 4.

6) If your vehicle will be towing a

trailer, load from your trailer will be

transferred to your vehicle. Consult

this manual to determine how this

reduces the available cargo and

luggage load capacity of your vehi-

cle.

Vehicle Loading Example

As an example, suppose that the Tire

and Loading Information label on your

vehicle indicates that your vehicle’s

total load capacity is 950 lbs. If you

were to drive your vehicle with one

passenger, and the total combined

weight of you and your passenger was

350 lbs, then the cargo and luggage

capacity of your vehicle would be 600

lbs (950 – 350 = 600 lbs).

If you later added 2 more passengers,

having a combined weight of 325 lbs,

the cargo and luggage capacity of

your vehicle would be reduced from

600 lbs to 275 lbs (600 – 325 = 275

lbs). As you can see, as the number

and combined weight of vehicle occu-

pants increase, the vehicle’s cargo

and luggage capacity decreases.

Suppose again, that you were to take

a trip in your vehicle with the same

three passengers described above,

and you decided to tow a trailer having

a trailer tongue weight of 75 lbs. The

cargo and luggage capacity would be

reduced again, to 200 lbs (275 – 75 =

200 lbs).

Determining Compatibility of Tire

and Vehicle Load Limits

The tires on your vehicle, when they

are inflated to the recommended tire

inflation pressure, have a load-carry-

ing capacity that is greater than the

load that will be on the tires when the

vehicle is at its GVWR or GAWR limit.

Never use replacement tires that have

a load-carrying capacity less than the

original tires on your vehicle. Tire load-

carrying capacity information is

molded into the tire sidewall typically

shown as “Max. Load”. Use of replace-

ment tires with a lower load-carrying

capacity than the original tires, or fail-

ure to keep the tires inflated to recom-

mended tire pressure, may reduce the

GVWR or GAWR limit of your vehicle.

NOTE:

Use of replacement tires with a higher

load-carrying capacity than the origi-

nal tires, or using a tire inflation pres-

sure higher than the recommended

tire inflation pressure, will not increase

the GVWR or GAWR limit of your vehi-

cle.

Fuses: 7

Headlight Aiming:

Bulb Replacement: 7

7-36

INSPECTION AND MAINTENANCE

79K21-03E

Battery

60A269

Your vehicle is equipped with a battery that

requires infrequent maintenance. You will

never have to add water. You should, how-

ever, periodically check the battery, battery

terminals and battery hold-down bracket

for corrosion. Remove corrosion using a

stiff brush and ammonia mixed with water,

or baking soda mixed with water. After

removing corrosion, rinse with clean water.

The test indicator on the top of the battery

provides information on the condition of

the battery.

If your vehicle is not going to be driven for

a month or longer, disconnect the cable

from the negative terminal of the battery to

help prevent discharge.

Fuses

Your vehicle has three types of fuses, as

described below:

Main Fuse – The main fuse takes current

directly from the battery.

Primary Fuses – These fuses are between

the main fuse and individual fuses, and are

for electrical load groups.

Individual Fuses – These fuses are for indi-

vidual electrical circuits.

For details on protected circuits, refer to

the “FUSES AND PROTECTED CIR-

CUITS” section in this manual.

WARNING

Batteries produce flammable hydro-

gen gas. Keep flames and sparks

away from the battery or an explosion

may occur. Never smoke when work-

ing near the battery.

WARNING

When checking or servicing the bat-

tery, disconnect the negative cable.

Be careful not to cause a short circuit

by allowing metal objects to contact

the battery posts and the vehicle at

the same time.

EXAMPLE

WARNING

To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions in the

“EMERGENCY SERVICE” section of

this manual if it is necessary to jump

start your vehicle.

WARNING

Battery posts, terminals and related

accessories contain lead and lead

compounds. Wash hands after han-

dling.

Bulb Replacement: 7

7-37

INSPECTION AND MAINTENANCE

79K21-03E

Main Fuse Box

64J157

The main fuse, primary fuses and some of

the individual fuses are located in the

engine compartment. If the main fuse

blows, no electrical component will func-

tion. If a primary fuse blows, no electrical

component in the corresponding load

group will function. When replacing the

main fuse or a primary fuse, use a genuine

SUZUKI replacement.

Main Fuse / Primary Fuse

(1) 15A CPRSR A/C compressor fuse

(2) 20A O2 HTR

sensor heater

fuse

(3) 15A THR MOT Throttle motor fuse

(4) 20A AT

Automatic transmis-

sion fuse

(5) 25A RR DEF Rear defogger fuse

(6) 15A HORN Horn fuse

(7) 20A FR FOG Front fog light fuse

(8) 20A MRR HTR Mirror heater fuse

(9) 40A FR BLW

Front blower motor

fuse

(10) 30A ABS 2 ABS actuator fuse

(11) 50A ABS 1 ABS actuator fuse

(12) 20A FI Main fuse

(13) – – Blank

(14) 10A H/L L

Head light high beam

fuse, left

(15) 10A H/L R

Head light high beam

fuse, right

(16) 10A H/L Head light fuse

(17) 40A ST Starter motor fuse

(18) 40A IGN Ignition fuse

(19) 15A H/L LO L

Head light low beam

fuse, left

(20) 15A H/L LO R

Head light low beam

fuse, right

PRIMARY

FUSE

INDIVIDUAL FUSE

60A LAMP Head light, Accessory,

Dome light, Sunroof,

Hazard light, Door lock,

Rear fog light, Stop

lamp, Tail light

50A IGN 2 Wiper/Washer, Power

window, Seat heater

40A 4WD 4WD actuator

30A RDTR 1 Radiator fan

30A RDTR 2 Radiator fan

WARNING

If a fuse in the main fuse box blows,

be sure to have your vehicle

inspected by an authorized SUZUKI

dealer. Always use a genuine SUZUKI

replacement. Never use a substitute

such as a wire even for a temporary

fix, or extensive electrical damage

and a fire can result.

Bulb Replacement: 7

7-38

INSPECTION AND MAINTENANCE

79K21-03E

Fuse under the Dash Board

Fuse box

64J192

79K057

65D045

The fuse box is located under the driver’s

side of the dashboard. To remove a fuse,

use the fuse puller provided in the fuse

box.

SPARE

USE THE DESIGNATED

FUSES AND RELAYS ONLY

SPARE SPARE

(A)(B)(C)(D)(E)(F)(G)(H)(I)(J)

(L)(M)(N)(O)(P)(Q)(R)(S)(T)(U)(V)

(K)

(W)(X)

(A) 10A DOME Dome lamp fuse

(B) 10A STOP Stop lamp fuse

(D) 15A ACC 3

Accessory socket

fuse

(E) 10A CRUISE Cruise control fuse

(F) 15A ACC 2

Cigar or Accessory

socket fuse

(G) 20A WIP Wiper fuse

(H) 15A IG2 SIG

Ignition signal & Seat

heater fuse

(I) 10A BACK Back lamp fuse

(J) 10A ABS/ESP

ABS or ESP control-

ler fuse

(K) 10A A/B Air bag fuse

(L) 15A RADIO Radio fuse

(M) 15A HAZ Hazard light fuse

(N) 7.5A ST SIG Starter signal fuse

(O) 10A ECM

Engine control

module fuse

(P) 25A S/R Sun roof motor fuse

(Q) 25A B/U Buck up fuse

(R) 10A TAIL Tail light fuse

(S) 20A D/L

Door lock actuator

fuse

(T) 15A ACC

Radio, Remote door

mirror fuse

(U) 10A METER Meter fuse

(V) 15A IG COIL Ignition coil fuse

(W) – – Blank

(X) 30A P/W Power window fuse

Bulb Replacement: 7

7-39

INSPECTION AND MAINTENANCE

79K21-03E

NOTE:

Make sure that the fuse box cover always

carries spare fuses.

60A243

81A283

Headlight Aiming

Since special procedures are required, we

recommend you take your vehicle to your

SUZUKI dealer for headlight alignment.

WARNING

Always be sure to replace a blown

fuse with a fuse of the correct amper-

age. Never use a substitute such as

aluminum foil or wire to replace a

blown fuse. If you replace a fuse and

the new one blows in a short period

of time, you may have a major electri-

cal problem. Have your vehicle

inspected immediately by your

SUZUKI dealer.

BLOWN

BLOWNOK

Bulb Replacement: 7

Wiper Blades: 3

7-40

INSPECTION AND MAINTENANCE

79K21-03E

Bulb Replacement

NOTE:

If it is difficult to replace headlight bulbs or

clearance light bulbs due to under-hood

components trust this job to your dealer.

Center Interior Light (if equipped)

64J159

Pull down the lens by using a flat blade

screwdriver covered with a soft cloth as

shown. To install it, simply push it back in.

The bulb can be removed by simply pulling

it out. When replacing the bulb, make sure

that the contact springs are holding the

bulb securely.

Rear Interior Light (if equipped)

64J160

Pull down the lens by using a flat blade

screwdriver covered with a soft cloth as

shown. To install it, simply push it back in.

The bulb can be removed by simply pulling

it out.

WARNING

• Light bulbs can be hot enough to

burn your finger right after being

turned off. This is true especially

for halogen headlight bulbs.

Replace the bulbs after they

become cool enough.

• The headlight bulbs are filled with

pressurized halogen gas. They can

burst and injure you if they are hit

or dropped. Handle them carefully.

CAUTION

The oils from your skin may cause a

halogen bulb to overheat and burst

when the lights are on. Grasp a new

bulb with a clean cloth.

CAUTION

Frequent replacement of a bulb indi-

cates the need for an inspection of

the electrical system. This should be

carried out by your SUZUKI dealer.

Wiper Blades: 3

7-41

INSPECTION AND MAINTENANCE

79K21-03E

Spot Light (if equipped)

Pull down the lens by using a flat blade

screwdriver covered with a soft cloth as

shown.

Ceiling-mount type (if equipped)

79K061

Remove the bulb holder by turning it coun-

terclockwise. Pull out the bulb.

Headlights

Low beam

(Halogen headlamp)

79K089

66J108

Open the engine hood. Disconnect the

coupler. Remove the sealing rubber.

Push the retaining spring forward and

unhook it. Then remove the bulb. Install a

new bulb in the reverse order of removal.

High beam

78F072

Open the engine hood. Disconnect the

coupler while pushing the lock release.

Turn the bulb holder counterclockwise to

remove it.

Wiper Blades: 3

7-42

INSPECTION AND MAINTENANCE

79K21-03E

Front Fog Light

79K090

1) Insert a flat blade screwdriver into the

hole (2) and remove the clips (1) by

twist the driver as shown in the illustra-

tion.

2) Remove the bolt (3) by a Phillips-head

screwdriver.

65J357

3) Remove the clip (4) with the same way

as No.1).

78F072

4) Open the fender cover. Disconnect the

coupler with pushing the lock release.

Turn the bulb holder counterclockwise

and remove it.

(2)

(1)

(3)

(4)

Wiper Blades: 3

7-43

INSPECTION AND MAINTENANCE

79K21-03E

Other General Lights

Bulb holder

54G123

(1) Removal

(2) Installation

To remove a bulb holder from a light hous-

ing, turn the holder counterclockwise and

pull it out. To install the holder, push the

holder in and turn it clockwise.

Bulb

54G124

(3) Removal

(4) Installation

There are two types of bulb, “Full glass

type” (1) and “Glass/metal type” (2).

To remove and install a full glass type bulb

(1), simply pull out or push in the bulb.

To remove a glass metal type bulb (2) from

a bulb holder, push in the bulb and turn it

counterclockwise. To install a new bulb,

push it in and turn it clockwise.

You can access the individual bulb or bulb

holders as follows.

Position/Turn signal light

64J163

To replace the bulb of position/turn signal

light, follow the procedure for the bulb

replacement of the “Front Fog Light”.

Rear combination light

78K124

(1)

(2)

EXAMPLE

(1)

(2)

(3)

(4)

EXAMPLE

Air Conditioning System: 4

7-44

INSPECTION AND MAINTENANCE

79K21-03E

License plate light

65J345

Turn the cover (1) counterclockwise to

remove it.

NOTE:

When reinstalling, put the packing (2)

between the cover and bulb holder.

Door illumination light

64J165

Luggage compartment light

64J166

High-mount stop light (if equipped)

The followings are the general procedure

for replace the bulbs of high-mount stop

light.

Since special procedures are required, we

recommend you take your vehicle to your

SUZUKI dealer for the bulbs of high-mount

stop light replacement.

64J181

To remove a high-mounted stop light hous-

ing the following procedure:

1) Open the tailgate, and remove the trim

(1) as shown in the illustration.

(1)

(2)

(1)

7-45

INSPECTION AND MAINTENANCE

79K21-03E

64J182

2) Release the claws of the light housing

by the flat head etc. through the service

holes as shown in the illustration.

64J183

3) Close the tailgate. Remove a high-

mounted stop light housing (2) from the

tailgate.

64J184

4) Remove the each bulb.

5) Replace the bulbs.

To install a high-mounted stop light

housing in the reverse order of removal.

(2)

7-46

INSPECTION AND MAINTENANCE

79K21-03E

Wiper Blades

54G129

If the wiper blades become brittle or dam-

aged, or make streaks when wiping,

replace the wiper blades.

To install new wiper blades, follow the pro-

cedures below.

NOTE:

Some wiper blades may be different from

the ones described here depending on

vehicle specifications. If so, consult your

SUZUKI dealer for proper replacement

method.

For windshield wipers:

70G119

1) Hold the wiper arm away from the win-

dow.

52D102

2) Squeeze lock lever (1) towards wiper

arm (2) and remove the wiper frame

from the arm as shown.

CAUTION

To avoid scratching or breaking the

window, do not let the wiper arm

strike the window while replacing the

wiper blade.

7-47

INSPECTION AND MAINTENANCE

79K21-03E

60A260

3) Pull the locked end of the wiper blade

firmly to unlock the blade and slide the

blade out as shown.

52D124

(3) Retainer

4) If the new blade is provided without the

two metal retainers, move them from

the old blade to the new one.

Installation

52D125

(4) Locked end

5) Install the new blade in the reverse

order of removal, with the locked end

positioned toward the wiper arm. Make

sure the blade is properly retained by

all the hooks. Grasp the blade near the

locked end and pull in the direction of

the arrows to lock the end into place.

6) Reinstall wiper frame to arm, making

sure that the lock lever is snapped

securely into the arm.

7-48

INSPECTION AND MAINTENANCE

79K21-03E

For rear wipers:

80G146

1) Hold the wiper arm away from the win-

dow.

2) Remove the wiper frame from the arm

as shown.

3) Slide the blade out as shown.

65D151

NOTE:

Do not flex the wiper blade frame end more

than necessary. If you do, it can break off.

54G135

(1) Retainer

4) If the new blade is provided without the

two metal retainers, move them from

the old blade to the new one.

5) Install the new blade in the reverse

order of removal.

Make sure the blade is properly

retained by all the hooks.

6) Reinstall wiper frame to arm in the

reverse order of removal.

7-49

INSPECTION AND MAINTENANCE

79K21-03E

Windshield Washer Fluid

Front and rear (if equipped)

66J008

66J116

Check that there is washer fluid in the tank

by looking at the washer fluid level gauge

which is attached to the cap of the washer

fluid tank. If the fluid level is near empty,

refill it.

Use a good quality windshield washer

fluid, diluted with water as necessary.

Air Conditioning System

If you do not use the air conditioner for a

long period, such as during winter, it may

not give the best performance when you

start using it again. To help maintain opti-

mum performance and durability of your air

conditioner, it needs to be run periodically.

Operate the air conditioner at least once a

month for one minute with the engine

idling. This circulates the refrigerant and oil

and helps protect the internal components.

(or opposite side)

EXAMPLE

WARNING

Do not use “anti-freeze” solution in

the windshield washer reservoir. This

can severely impair visibility when

sprayed on the windshield, and also

damage your vehicle’s paint.

CAUTION

Damage may result if the washer

motor is operated with no fluid in the

washer tank.

Inspection and Maintenance for Your Suzuki Grand Vitara SUV Second Generation (2005-2015)

Related Topics

Popular Owner Manuals

Latest Owner Manuals