Get FOR SAFE DRIVING -> Child restraint system for countries applied for UN Regulation No.16 Guide for Suzuki Jimny SUV Fourth Generation (2018-2026)

Child restraint system for

countries applied for UN

Regulation No.16

.A. CAUTION

Adjust the height of the head

restraint or remove it for fitting the

child restraint, as necessary. How-

ever, if a booster cushion not

equipped with the head restraint is

fitted, the head restraint should not

be removed. If the head restraint is

removed for fitting the child restraint,

you need to install it again after

removing the child restraint.

If the child restraint is fitted improp-

erly, a child sitting in it could be

injured in a collision. (Refer to

"Installation with lap-shoulder seat

belts" section,

11

lnstallation with ISO-

FIX type anchorages" section and

"Installation of child restraint with

top tether

11

section in this section for

details.)

Child restraint

The suitability of each passenger's seat

position for carriage of children and fitting

of child restraint system is shown in the

table.

Child restraint systems suitability for

each seat position (for the vehicle with

airbag deactivation switch)

The above illustration shows Left hand

drive vehicle.

NOTE:

Seat position number of G), @ and @ is

same as Left hand drive vehicle for Right

hand drive vehicle.

G) Front passenger's seat

@ Rear seat right side

@ Rear seat left side

G)

(ID@

(#1. #2. #3)

(2)

(ID~J,~

(#2, #3)

®

(ID~J,~

(#2. #3)

FOR SAFE DRIVING

It is suitable for univer-

sal category of child

restraint system fixed

with the vehicle seat

belt.

It is suitable for i-Size

and ISOFIX child

restraint system.

This seat is equipped

with Top tether anchor-

age point.

Never use a rear-fac-

ing child restraint sys-

tem on the passenger

seat when the front

passenger airbag is

activated.

#1: Move the front seat fully rearward.

#2: When you install a forward-facing

child restraint, if there is a gap or

space between the child restraint

and the seatback, adjust the seat-

back angle in order to install the

child restraint system properly.

#3: If the head restraint interferes with

the child restratint system, adjust

the height of the head restraint or

remove it, as necessary.

NOTE:

For the Installation suitability of child

restraint systems of Taiwan models,

refer to "For Taiwan" in the "SUPPLE-

MENT" section.

1-20

FOR SAFE DRIVING

Detailed information for child restraint system (for the vehicle with airbag deactivation switch)

Seating position

Seat position number

Seating position suitable for universal belted

(YES/NO)

i-Size seating position

(YES/NO)

Seating position suitable for lateral fixture

(L 1/L2)

Suitable rear-facing fixture

(R1/R2/R3)

Suitable front-facing fixture

(F2X/F2/F3)

Key of letters to be inserted in the above table

YES =Suitable for this seating position

NO = Not suitable for this seating position

Front

Passenger

airbag is

activated

NO

X =ISOFIX position is not suitable for ISOFIX child restraint systems in this fixture.

G)

ISOFIX child restraint systems are divided into different mass group, size class and fixture.

Front

Passenger

airbag is

deactivated

YES

NO

The child restraint system can be used in the seating positions for fixture shown in the above table.

For mass group, size class and fixture, confirm the table of next page.

NOTE:

(2)

YES

X

R1, R2

F2X, F2, F3

@

YES

YES·

X

R1, R2

F2X, F2, F3

For the Installation suitability of child restraint systems of Taiwan models, refer to "For Taiwan" in the "SUPPLEMENT' section.

1-21

FOR SAFE DRIVING

If your child restraint system has no size class (or if you cannot find information in the following table),

refer to the child restraint system suitability information for the vehicle or ask the retailer of your child seat.

Mass group Size class

F

0

G

(up to 10 kg)

E

O+

D

(up to 13kg)

C

D

C

I

8

(9kg to 18kg)

81

A

II

X

(15kg to 25kg)

Ill

X

(22kg to 36kg)

Key of letters to be inserted in the above table

X = There is no fixture for this mass group.

NOTE:

Fixture

Description

L1

Left Lateral facing position Child Restraint Systems (carry-cot)

L2

Right Lateral facing position Child Restraint Systems (carry-cot)

R1 Rear-facing seat

. R1 Rear-facing seat

R2

Reduced-Size rear-facing toddler Child Restraint Systems

R3 Full-Size rear-facing toddler Child Restraint Systems

R2

Reduced-Size rear-facing toddler Child Restraint Systems

R3

Full-Size rear-facing toddler Child Restraint Systems

F2

Reduced-Height front-facing toddler Child Restraint Systems

F2X

Reduced-Height front-facing toddler Child Restraint Systems

F3

Full-Height front-facing toddler Child Restraint Systems

X

-

X -

For the Installation suitability of child restraint systems of Taiwan models, refer to "For Taiwan" in the "SUPPLEMENT" section.

1-22

FOR SAFE DRIVING

Installation suitability of SUZUKI recommendation child restraint systems (for the vehicle with airbag deactivation switch)

Recommendation of

Mass group

Child restraint system (#A)

0,0+

Britax Romer Baby-Safe i-Size

(up to 13kg)

I

Britax Romer Duo Plus

(9kg to 18kg)

11, Ill

Britax Romer Kid Fix XP

(15kg to 36kg)

Key of letters to be inserted in the above table

YES =It is suitable for this seating position

NO = II is not suitable for this seating position

#1: Only belted.

Seating position

G)

Front

(2)

Passenger

airbag is airbag is

activated

deactivated

NO

YES (#1) YES (#1)

NO

YES (#1) YES

NO

YES (#1)

YES

#A: These child restraint systems are SUZUKI Genuine Accessory, refer to the accessories catalog.

However, there are countries which do not sell this child restraint system.

1-23

@

YES (#1)

YES

Child restraint systems suitability for

each seat position (for the vehicle with-

out airbag deactivation switch)

The above illustration shows Left hand

drive vehicle.

NOTE:

Seat position number of G), @ and @ is

same as Left hand drive vehicle for Right

hand drive vehicle.

G) Front passenger's seat

@ Rear seat right side

@ Rear seat left side

G)

(#1, #2, #3)

(#2, #3)

@

(#2, #3)

(gJ

(g)@

[g)~l~

It is suitable for univer-

sal category of child

restraint system fixed

with the vehicle seat

belt.

It is suitable for i-Size

and ISOFIX child

restraint system.

This seat is equipped

with Top tether anchor-

age point.

Never use a rear-fac-

ing child restraint sys-

tem on the passenger

seat.

FOR SAFE DRIVING

#1: Move the front seat fully rearward.

#2: When you install a forward-facing

child restraint, if there is a gap or

space between the child restraint

and the seatback, adjust the seat-

back angle in order to install the

child restraint system properly.

#3: If the head restraint interferes with

the child restratint system, adjust

the height of the head restraint or

remove it, as necessary.

1-24

FOR SAFE DRIVING

Detailed information for child restraint system (for the vehicle without airbag deactivation switch)

Seat position number

Seating position suitable for universal belted

(YES/NO)

· i-Size seating position

(YES/NO)

Seating position suitable for lateral fixture

(L 1 /L2)

Suitable rear-facing fixture

(R1/R2/R3)

Suitable front-facing fixture

(F2X/F2/F3)

Key of letters to be inserted in the above table

YES =Suitable for this seating position

NO = Not suitable for this seating position

X =ISOFIX position is not suitable for ISOFIX child restraint systems in this fixture.

CD

YES (#1)

NO

ISOFIX child restraint systems are divided into different mass group, size class and fixture.

The child restraint system can be used in the seating positions for fixture shown in the above table.

For mass group, size class and fixture, confirm the table of next page.

#1: When installing the child restraint systems, only a front-facing fixture is suitable.

1-25

Seating position

@

YES

X

R1, R2

F2X, F2, F3

@

YES

X

R1, R2

F2X, F2, F3

FOR SAFE DRIVING

If your child restraint system has no size class (or if you cannot find information in the following table),

refer to the child restraint system suitability information for the vehicle or ask the retailer of your child seat.

Mass group

Size class

F

0

G

(upto 10kg)

E

O+

D

(up to 13kg)

C

D

C

I

B

(9kg to 18kg)

B1

A

II

X

(15kg to 25kg)

Ill

X

(22kg to 36kg)

Key of letters to be inserted in the above table

X; There is no fixture for this mass group.

Fixture

Description

L1 Left Lateral facing position Child Restraint Systems (carry-cot)

L2 Right Lateral facing position Child Restraint Systems (carry-cot)

R1

Rear-facing seat

R1

Rear-facing seat

R2 Reduced-Size rear-facing toddler Child Restraint Systems

R3 Full-Size rear-facing toddler Child Restraint Systems

R2 Reduced-Size rear-facing toddler Child Restraint Systems

R3

Full-Size rear-facing toddler Child Restraint Systems

F2

Reduced-Height front-facing toddler Child Restraint Systems

F2X

Reduced-Height front-facing toddler Child Restraint Systems

F3 Full-Height front-facing toddler Child Restraint Systems

X

-

X

-

1-26

FOR SAFE DRIVING

Installation suitability of SUZUKI recommendation child restraint systems (for the vehicle without airbag deactivation switch)

Recommendation of

Mass group

Child restraint system (#A)

0,0+

Britax Romer Baby-Safe i-Size

(up to 13kg)

I

Britax Romer Duo Plus

(9kg to 18kg)

II, II I

Britax Romer KidFix XP

(15kg to 36kg)

Key of letters to be inserted in the above table

YES =II is suitable for this seating position

NO = It is not suitable for this seating position

#1: Only belted.

G)

NO

YES (#1)

#A: These child restraint systems are SUZUKI Genuine Accessory, refer to the accessories catalog.

However, there are countries which do not sell this child restraint system.

1-27

Seating position

(2)

@

YES (#1) YES (#1)

YES YES

Approval mark to meet child

restraint system regulation for UN

R44 / R129 regulation

The following mark is shown on the child

restraint system to meet the regulation of

UN R44 / R129 for the child restraint sys-

tem.

ECE R44/04

(1)

ECE R129

Universal

(2)

i-Size

(3)

-18kg Y

(5)

40cm • 70cm I:!. 24kg

(4)

@

(6)

@

********

(7)

********

78RB01010

(1) Regulation number

(2) Suitability for child restraint system

category

(3) Weight range of the applicable child

who is applicable for this approval

mark as shown in the mark

(4) Height range and weight range of the

applicable child who is applicable for

this approval mark in the mark

(5) Specification of appliance

(6) Country code which approved child

restraint system

(7) Approval number of child restraint seat

This approval mark is a representative

example.

NOTE:

UN R44 I R129 means the international

regulation for the child restraint system.

"EGE" is shown on the mark in the illus-

tration for the child restraint system. This

"EGE" mark is the same as "UN".

FOR SAFE DRIVING

Installation with lap-shoulder seat

belts

A CAUTION

If your vehicle is equipped with the

head restraint, adjust the height of

the head restraint or remove it for fit-

ting the child restraint, as necessary.

However, if a booster cushion not

equipped with the head restraint is

fitted, the head restraint should not

be removed. If the head restraint is

removed for fitting the child restraint,

you need to install it again after

removing the child restraint.

If the child restraint is fitted improp-

erly, a child sitting in it could be

injured in a collision.

NOTE:

Stow the removed head restraint in the lug-

gage compartment so it will not cause

inconvenience to the occupants.

1-28

FOR SAFE DRIVING

ELR type belt

80JC021

1-29

(For models with front passenger airbag

deactivation system)

Whenever possible, SUZUKI recom-

mends that child restraint systems be

installed on . th_e rear seat. According to·

accident stat1st1cs, children are safer when

~roperly restrained in rear seating posi-

tions than in front seating positions.

• If you must install the child restraint sys-

tem on the front passenger's seat follow

instructions below. '

- D_eactivate the front passenger's front

airbag by the front passenger airbag

d~activation system (if equipped).

- Slide the seat to the most rear position

by the seat position adjustment lever.

- If there is a gap or space between the

child restraint and the seatback, adjust

the seatback angle in order to install

the child restraint system properly.

Install your child restraint system accord-

ing to the instructions provided by the child

restraint system manufacturer.

Check that the seat belt is securely

latched.

Move the child restraint system in all direc-

tions to check that it is securely installed.

When you put your child in the child

restraint system, appropriately slide the

front seat forward not to touch a part of

your child's body.

Installation with ISOFIX type

anchorages

78RB02020

Your vehicle is equipped with the lower

anchorages in the rear seat outboard seat-

ing positions for securing a ISOFIX type of

child restraints with the connecting bars.

The lower anchorages are located where

the rear of the seat cushion meets the bot-

tom of the seatback.

A WARNING

Install the ISOFIX type of child

restraint(s) in the only outboard seat-

ing positions, not in the central posi-

tion for the rear seat.

Install the ISOFIX type child restraint sys-

tem according to the instructions provided

by the child restraint system manufacturer.

After installation, try moving the child

restraint system in all directions especially

forward to check that connecting bars are

securely latched to the anchorages.

84MM00252

Your vehicle is equipped with the top tether

anchorages. Use the top tether strap of the

child restraint according to the instructions

provided by the child restraint system man-

ufacturer.

Here is a general instruction:

A CAUTION

If your vehicle is equipped with the

head restraint, adjust the height of

the rear head restraint or remove it

for fitting the child restraint, as nec-

essary. However, if a booster cushion

not equipped with the head restraint

is fitted, the head restraint should not

be removed. If the head restraint is

removed for fitting the child restraint,

you need to install it again after

removing the child restraint.

If the child restraint is fitted improp-

erly, a child sitting in it could be

injured in a collision.

NOTE:

Stow the removed head restraint in the lug-

gage comparlment so it will not cause

inconvenience to the occupants.

FOR SAFE DRIVING

78F114

1) Place the child restraint in the rear seat,

inserting the connecting bars to the

anchorages between the seat cushion

and the seatback.

1-30

FOR SAFE DRIVING

68LM268

2) Use your hands to carefully align the

connecting bar tips with the anchor-

ages. Take care not to pinch your fin-

gers.

1-31

54G184

3) Push the child restraint toward the anchor-

ages so that the connecting bar tips are

partially hooked to the anchorages. Use

your hands to confirm the position.

54G185

4) Grasp the front of the child restraint and

push the child restraint forcefully to

latch the connecting bars. Check that

they are securely latched by trying to

move the child restraint system in all

directions, especially forward.

5) Attach the top tether strap referring to

"Installation of child restraint with top

tether" section.

When you put your child in the child

restraint system, appropriately slide the

front seat forward not to touch a part of

your child's body.

NOTICE

When installing a child restraint sys-

tem to the rear seat, adjust the front

seat position so that the front seat

does not interfere with the child

restraint system.

Installation of child restraint with

top tether

78RB02021

Some child restraint systems require the

use of a top tether strap. Top tether anchor-

age brackets are provided in your vehicle at

the locations shown in the illustrations.

The number of the top tether anchorage

brackets provided in your vehicle depends

on the vehicle specification. Install the child

restraint system as follows:

1) Secure the child restraint on the rear

seat using the procedure described

above for securing a restraint system

that does not require a top tether strap.

2) Hook the top tether strap to the top

tether anchorage bracket and tighten

the top tether strap according to the

instructions provided by the child

restraint system manufacturer. Attach

the top tether strap to the correspond-

ing top tether anchorage bracket

located directly behind the child

restraint. Do not attach the top tether

strap to the luggage restraint loops (if

equipped).

A WARNING

Do not attach the child restraint top

tether strap to the luggage restraint

loops (if equipped). Incorrectly

attached top tether strap will reduce

the intended effectiveness of the

child restraint system.

FOR SAFE DRIVING

52RS20431

3) When routing the top tether strap, pass

the top tether strap as shown in the

illustration. (Refer to "Head restraints"

section for details on how to adjust the

height of head restraint or remove it.)

4) Check that cargo does not interfere

with routing of the top tether strap.

1-32

FOR SAFE DRIVING

NOTICE

When installing a child restraint sys-

tem to the rear seat, adjust the front

seat position so that the front seat

does not interfere with the child

restraint system.

NOTE:

For Australian models, refer to "For Austra-

lia" in the "SUPPLEMENT" section.

1-33

Seat belt pretensioner system

A WARNING

This section describes your SUZUKI

vehicle's seat belt pretensioner sys-

tem. Read and follow all these

instructions carefully to minimize

your risk of severe injury or death.

To determine if your vehicle is equipped

with a seat belt pretensioner system at the

front or rear seating positions, check the

label on the seat belt at the bottom part. If

the letters "p" and/or "PRE" appear as illus-

trated, your vehicle is equipped with the

seat belt pretensioner system. You can use

the pretensioner seat belts in the same

manner as ordinary seat belts.

Read this section and "Supplemental

restraint system (airbags)" section to learn

more about the pretensioner system.

The seat belt pretensioner system works

with the supplemental restraint system (air-

bags). The crash sensors and the elec-

tronic controller of the airbag system also

control the seat belt pretensioners. The

pretensioners are triggered only when

there is a frontal or side collision severe

enough to trigger the airbags and the seat

belts are fastened. For precautions and

general information including servicing the

pretensioner system, refer to "Supplemen-

tal restraint system (airbags)" section in

addition to this "Seat belt pretensioner sys-

tem" section, and follow all those precau-

tions.

The pretensioner is located in each front

seat belt retractor and each rear seat belt

retractor in outboard seating position. The

pretensioner tightens the seat belt so the

belt fits the occupant's body more snugly in

the event of a frontal or side collision. The

retractors will remain locked after the pre-

tensioners are activated. Upon activation,

some noise will occur and some smoke

may be released. These conditions are not

harmful and do not indicate a fire in the

vehicle.

The driver and all passengers must be

properly restrained by fastening seat belts

at all times, whether or not a pretensioner

is equipped at their seating position, to

minimize the risk of severe injury or death

in the event of a collision.

Sit fully back in the seat; sit up straight; do

not lean forward or sideways. Adjust the

belt so the lap portion of the belt is worn

low across the pelvis, not across the waist.

Please refer to "Seat adjustment" section

and the instructions and precautions about

the seat belts in this "Seat belts and child

restraint systems" section for details on

proper seat and seat belt adjustments.

Please note that the pretensioners along

with the airbags will activate in severe fron-

tal or side collisions. They are not

designed to activate in rear impacts, roll-

overs, or minor frontal side collisions. The

pretensioners can be activated only once.

If the pretensioners are activated (that is, if

the airbags are activated), have the pre-

tensioner system serviced by a SUZUKI

dealer as soon as possible.

FOR SAFE DRIVING

If AIRBAG light on the instrument cluster

does not blink or come on briefiy when the

ignition switch is turned to "ON" position,

stays on for more than 1 O seconds, or

comes on while driving, the pretensioner

system or the airbag system may not work

properly. Have both systems inspected by

a SUZUKI dealer as soon as possible.

Service on or around the pretensioner sys-

tem components or wiring must be per-

formed only by a SUZUKI dealer who is

specially trained. Improper service could

result in unintended activation of preten-

sioners or could render the pretensioner

inoperative. Either of these two conditions

may result in personal injury.

To prevent damage or unintended activa-

tion of the pretensioners, check that the

lead-acid battery is disconnected and the

ignition switch has been in "LOCK" position

for at least 90 seconds before performing

any electrical service work on your

SUZUKI vehicle.

Do not touch pretensioner system compo-

nents or wiring. The wires are wrapped

with yellow tape or yellow tubing, and the

couplers are yellow. When scrapping your

SUZUKI vehicle, ask a SUZUKI dealer,

body repair shop, or scrap yard for assis-

tance.

1-34

FOR SAFE DRIVING -> Child restraint system for countries applied for UN Regulation No.16 for Your Suzuki Jimny SUV Fourth Generation (2018-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals