Get EMERGENCY SERVICE -> Jacking instructions Guide for Suzuki Swift 4 Door Fourth Generation (2023-2026)

EMERGENCY SERVICE

Jacking instructions

WARNING

EXAMPLE

• Shift into “P” (Park) for a CVT, or into

“R” (Reverse) for a manual transaxle

vehicle when you jack up the vehi-

cle.

• Never jack up the vehicle with the

transaxle in “N” (Neutral). Other-

wise, unstable jack may cause an

accident.

3) Turn on the hazard warning switch if

your vehicle is near traffic.

4) Block the front and rear of the wheel

diagonally opposite of the wheel being

lifted.

52RM80020

5) Place the spare tire (if equipped) near

the wheel being lifted as shown in the

illustration in case the jack slips.

75F062

EXAMPLE

1) Place the vehicle on level, hard ground.

2) Set the parking brake firmly and shift

into “P” (Park) if your vehicle has a

CVT, or shift into “R” (Reverse) if your

vehicle has a manual transaxle.

EXAMPLE

52RM80030

54G253

8-2

EMERGENCY SERVICE

6) Position the jack at an angle as shown

in the illustration and raise the jack by

turning the jack handle clockwise until

the jack-head groove fits around the

jacking bar beneath the vehicle body.

7) Continue to raise the jack slowly and

smoothly until the tire clears the

ground. Do not raise the vehicle more

than necessary.

WARNING

• Use the jack only to change wheels

on level, hard ground.

• Never jack up the vehicle on an

inclined surface.

• Never raise the vehicle with the

jack in a location other than the

specified jacking point (shown in

the illustration) near the wheel to

be changed.

• Check that the jack is raised at

least 25 mm (1 inch) before it con-

tacts the flange. Use of the jack

when it is within 25 mm (1 inch) of

being fully collapsed may result in

failure of the jack.

• Never get under the vehicle when it

is supported by the jack.

• Never run the engine when the

vehicle is supported by the jack

and never allow passengers to

remain in the vehicle.

8-3

EMERGENCY SERVICE

Raising vehicle with garage jack

EXAMPLE

• Apply the garage jack to one of the

points indicated below.

(1)

(2)

• Always support the raised vehicle with

jack stands (commercially available) at

the points indicated below.

(3)

(1)

(2)

(5)

(4)

52RS80020

(1) Front

(4) Garage jack

(5) Jacking point for garage jack

(2) Rear

(3) Jack stand

8-4

EMERGENCY SERVICE

4) Remove the wheel nuts and wheel.

6) Install the new wheel and replace the

wheel nuts with their cone shaped end

facing the wheel. Tighten each nut

snugly by hand until the wheel is

securely seated on the hub.

NOTICE

EXAMPLE

Never apply a garage jack to the

exhaust pipe, side under spoiler (if

equipped), engine undercover or rear

torsion beam.

(1)

EXAMPLE

NOTE:

For more details, contact an authorized

SUZUKI dealer.

Changing wheels

To change a wheel, use the following pro-

cedure:

1) Prepare the jack and tools.

2) Loosen, but do not remove the wheel

nuts.

3) Jack up the vehicle (follow the jacking

instructions in this section).

(2)

(3)

(4)

52RM80070

Tightening torque for wheel nut

100 Nm (10.2 kg-m, 74.0 lb-ft)

WARNING

7) Lower the jack and fully tighten the nuts

with a wheel wrench in numerical order

as shown in the illustration.

• Shift into “P” (Park) for a CVT, or into

“R” (Reverse) for a manual transaxle

vehicle when you jack up the vehicle.

• Never jack up the vehicle with the

transaxle in “N” (Neutral). Other-

wise, unstable jack may cause an

accident.

65J4033

5) Clean any mud or dirt off from the sur-

face of the wheel (1), hub (2), thread

part (3) and surface of the wheel nuts

(4) with a clean cloth.

Clean the hub carefully; it may be hot

from driving.

8-5

EMERGENCY SERVICE -> Jacking instructions for Your Suzuki Swift 4 Door Fourth Generation (2023-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals