Get INSPECTION AND MAINTENANCE -> Bulb replacement Guide for Suzuki Swift 4 Door Fourth Generation (2023-2026)

INSPECTION AND MAINTENANCE

Headlight aiming

Bulb replacement

Since special procedures are required, ask

an authorized SUZUKI dealer for this job.

CAUTION

• Light bulbs can be hot enough to

burn your finger right after turning

off lights. This is true especially for

halogen headlight bulbs. Replace

the bulbs after they become cool

enough.

OK

BLOWN

• The headlight bulbs are filled with

pressurized halogen gas. They can

burst and injure you if they are hit

or dropped. Handle them carefully.

• To avoid injury by sharp-edged

parts of the body, wear gloves and

a long-sleeved shirt when replacing

light bulbs.

81A283

WARNING

Always replace a blown fuse with a

fuse of the correct amperage. Never

use a substitute such as aluminum

foil or wire to replace a blown fuse. If

you replace a fuse and the new one

blows in a short period of time, you

may have a major electrical problem.

Have your vehicle inspected immedi-

ately by an authorized SUZUKI dealer.

NOTICE

The oils from your skin may cause a

halogen bulb to overheat and burst

when the lights are on. Grasp a new

bulb with a clean cloth.

NOTICE

Frequent bulb replacement indicates

the need for an inspection of the elec-

trical system. This should be carried

out by an authorized SUZUKI dealer.

7-27

INSPECTION AND MAINTENANCE

EXAMPLE

Headlights

EXAMPLE

LED type

(4)

(2)

Since special procedures are required, it is

recommended that you take your vehicle

to an authorized SUZUKI dealer for bulb

replacement.

(3)

Halogen type

EXAMPLE

(1)

52RM70320

52RM70230

1) Open the engine food while the engine

is stopped. Disconnect the coupler (2).

Remove the sealing rubber (3) by pull-

ing the grip (4).

NOTE:

You can see the position of retaining spring

from the hole of headlight.

52RM70220

(1) Bulb

(5)

52RM70330

2) Push the retaining spring (5) forward

and unhook it. Then remove the bulb.

Install a new bulb in the reverse order

of removal.

7-28

INSPECTION AND MAINTENANCE

Vehicle with the LED headlights

Front turn signal light and

front position light

EXAMPLE

For LED position light (if equipped), it is

recommended that you take your vehicle

to an authorized SUZUKI dealer for bulb

replacement since special procedures are

required.

(1)

Vehicle with the halogen headlights

EXAMPLE

68PH00732

52RM70140

(1)

1) Open the engine hood while the engine

is stopped. To remove the bulb holder

of the front turn signal light or the front

position light from the light housing,

turn the holder counterclockwise and

pull it out.

(1) Front turn signal light

(2)

52RM70240

(1) Front turn signal light

(2) Front position light (if equipped)

7-29

INSPECTION AND MAINTENANCE

Front fog light (if equipped)

Side turn signal light

EXAMPLE

Outside rearview mirror type

1) Start the engine. Turn the steering

wheel to the opposite side of the fog

light to be replaced to replace the bulb

easily. Then turn off the engine.

LED is used. It is recommended that you

take your vehicle to an authorized SUZUKI

dealer for bulb replacement since special

procedures are required.

(2)

EXAMPLE

Fender type

(3)

(4)

(1)

68PM00721

(3) Removal

(4) Installation

2) To remove the bulb of the front turn sig-

nal light (1) from the bulb holder, push

in the bulb and turn it counterclockwise.

To install a new bulb, push it in and turn

it clockwise.

(2)

57RK076

2) Remove the clip (1) and screws (2) at

the bottom of bumper.

64J195

To remove and install the bulb of the

front position light (2), simply pull out or

push in the bulb.

Since the bulb is built-in type, replace it as

the light assembly. Remove the light

assembly by sliding the light housing left-

ward with your finger.

For removing the clip, use a flat blade

screwdriver as show in the illustration.

7-30

INSPECTION AND MAINTENANCE

Daytime running light (if equipped)

LED type

Since special procedures are required, it is

recommended that you take your vehicle

to an authorized SUZUKI dealer for bulb

replacement.

Rear combination light

For LED tail / brake light, it is recom-

mended that you take your vehicle to an

authorized SUZUKI dealer for bulb

replacement since special procedures are

required.

(3)

(4)

EXAMPLE

52RM70250

52RS70030

3) Open the end of the cover inside the

fender.

2) Remove the wire (3) from a clamp (4).

3) To remove the bulb holder of the rear

turn signal light (5) or the reversing light

(6) from the light housing, turn the

holder counterclockwise and pull it out.

(2)

(1)

(4)

(3)

52RM70160

1) With the tailgate opened, remove the

bolts (1) and pull the light housing (2)

firmly to the rearward.

52R70140

4) Disconnect the coupler (3) by pushing

the lock release. Turn the bulb holder

(4) counterclockwise and remove it.

7-31

INSPECTION AND MAINTENANCE

License plate light

EXAMPLE

(5) / (6)

(7)

(8)

52RS70050

(1)

(7) Removal

(8) Installation

52RM70070

1) Remove the cover (1) by turning it

counterclockwise.

4) To remove and install the bulb of the

rear turn signal light (5) or the reversing

light (6), simply pull out or push in the

bulb.

52RM70190

NOTE:

When reinstalling the light housing, check

that the clips are properly attached.

7-32

INSPECTION AND MAINTENANCE -> Bulb replacement for Your Suzuki Swift 4 Door Fourth Generation (2023-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals