Get Maintenance and care Guide for Toyota 86 2 Door First Generation (2012-2021)

Maintenance and care

4

4-1. Maintenance and care

4-3. Do-it-yourself

maintenance

Cleaning and protecting

the vehicle exterior......... 308

Do-it-yourself service

precautions .................... 324

Hood ................................ 327

Positioning a floor jack..... 329

Engine compartment........ 331

Tires................................. 345

Tire inflation pressure ...... 353

Wheels............................. 357

Air conditioning filter......... 360

Cleaning and protecting

the vehicle interior.......... 312

Cleaning and protecting

the Alcantara^®area ....... 316

4-2. Maintenance

Maintenance

requirements.................. 318

General maintenance....... 320

Wireless remote control/

electronic key battery..... 363

Emission inspection and

maintenance (I/M)

programs........................ 323

Checking and replacing

fuses .............................. 367

Light bulbs........................ 375

307

4-1. Maintenance and care

Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in prime

condition.

● Working from top to bottom, liberally apply water to the vehicle

body, wheel wells and underside of the vehicle to remove any

dirt and dust.

● Wash the vehicle body using a sponge or soft cloth, such as a

chamois.

● For hard-to-remove marks, use car wash soap and rinse thor-

oughly with water.

● Wipe away any water.

● Wax the vehicle when the waterproof coating deteriorates.

If water does not bead on a clean surface, apply wax when the vehicle

body is cool.

308

4-1. Maintenance and care

■Automatic car washes

●Fold the mirrors before washing the vehicle. Start washing from the front

of the vehicle. Make sure to extend the mirrors before driving.

●Brushes used in automatic car washes may scratch the vehicle surface

and harm your vehicle’s paint.

■High pressure car washes

●Do not allow the nozzles of the car wash to come within close proximity

of the windows.

●Before using the car wash, check that the fuel filler door on your vehicle

is closed properly.

■Aluminum wheels

●Remove any dirt immediately by using a neutral detergent.

●Wash detergent off with water immediately after use.

●To protect the paint from damage, make sure to observe the following

precautions.

4

• Do not use acidic, alkaline or abrasive detergent

• Do not use hard brushes

• Do not use detergent on the wheels when they are hot, such as after

driving or parking in hot weather

■Brake (vehicles with brembo brake)

●Painted brake calipers

• When using detergent, use neutral detergent. Do not use hard brushes

or abrasive cleaners, as they will damage the paint.

• Do not use detergent on the brake calipers when they are hot.

• Wash detergent off immediately after use.

●Rust may form if the vehicle is parked with wet brake pads or disc rotors,

causing them to stick. Before parking the vehicle after it is washed, drive

slowly and apply the brakes several times to dry the parts.

■Parts containing resin such as the bumper

Do not scrub with abrasive cleaners.

309

4-1. Maintenance and care

WARNING

■When washing the vehicle

Do not apply water to the inside of the engine compartment. Doing so may

cause the electrical components etc. to catch fire.

■Precautions regarding the exhaust pipes

Exhaust gasses cause the exhaust pipes and rear bumper diffusers to

become quite hot.

When washing the vehicle, be careful not to touch the pipes and diffusers

until they have cooled sufficiently, as touching hot exhaust pipes and rear

bumper diffusers can cause burns.

NOTICE

■To prevent paint deterioration and corrosion on the body and compo-

nents (aluminum wheels etc.)

●Wash the vehicle immediately in the following cases:

• After driving near the sea coast

• After driving on salted roads

• If you see coal tar or tree sap on the paint surface

• If you see dead insects, insect droppings or bird droppings on the paint

• After driving in an area contaminated with soot, oily smoke, mine dust,

iron powder or chemical substances

• If the vehicle becomes heavily soiled in dust or mud

• If liquids such as benzene and gasoline are spilled on the paint surface

●If the paint is chipped or scratched, have it repaired immediately.

●To prevent the wheels from corroding, remove any dirt and store in a place

with low humidity when storing the wheels.

■Protective film for side sill plates

Make sure to remove the protective film. Failure to do so may cause rust,

depending on conditions.

310

4-1. Maintenance and care

NOTICE

■Cleaning the exterior lights

●Wash carefully. Do not use organic substances or scrub with a hard brush.

This may damage the surfaces of the lights.

●Do not apply wax on the surfaces of the lights.

Wax may cause damage to the lenses.

■To prevent damage to the windshield wiper arms

When lifting the wiper arms away from the windshield, pull the driver side

wiper arm upward first, and repeat for the passenger side. When returning

the wipers to their original position, do so from the passenger side first.

■When using a high pressure car wash

Do not bring the nozzle tip close to boots (rubber or resin manufactured

cover), connectors or the following parts. The parts may be damaged if they

come into contact with high-pressure water.

• Traction related parts

• Steering parts

4

• Suspension parts

• Brake parts

311

4-1. Maintenance and care

Cleaning and protecting the vehicle interior

The following procedures will help protect your vehicle's interior and

keep it in top condition:

■ Protecting the vehicle interior

● Remove dirt and dust using a vacuum cleaner. Wipe dirty sur-

faces with a cloth dampened with lukewarm water.

● If dirt cannot be removed, wipe it off with a soft cloth damp-

ened with neural detergent diluted to approximately 1%.

Wring out any excess water from the cloth and thoroughly

wipe off remaining traces of detergent and water.

■ Cleaning the leather areas

● Remove dirt and dust using a vacuum cleaner.

● Wipe any excess dirt and dust with a soft cloth dampened with

diluted detergent.

Use a diluted water solution of approximately 5% neutral wool

detergent.

● Wring out any excess water from the cloth and thoroughly

wipe off all remaining traces of detergent.

● Wipe the surface with a dry, soft cloth to remove any remain-

ing moisture. Allow the leather to dry in a shaded ventilated

area.

■ Cleaning the synthetic leather areas

● Remove dirt and dust using a vacuum cleaner.

● Wipe it off with a soft cloth dampened with neutral detergent

diluted to approximately 1%.

● Wring out any excess water from the cloth and thoroughly

wipe off remaining traces of detergent and water.

312

4-1. Maintenance and care

■Caring for leather areas

Toyota recommends cleaning the interior of the vehicle at least twice a year

to maintain the quality of the vehicle’s interior.

■Shampooing the carpets

There are several commercial foaming-type cleaners available. Use a

sponge or brush to apply the foam. Rub in overlapping circles. Do not apply

water. Excellent results are obtained by keeping the carpet as dry as possi-

ble.

■Seat belts

Clean with mild soap and lukewarm water using a cloth or sponge. Also

check the belts periodically for excessive wear, fraying or cuts.

WARNING

■Water in the vehicle

4

●Do not splash or spill liquid in the vehicle.

Doing so may cause electrical components etc. to malfunction or catch

fire.

●Do not get any of the SRS components or wiring in the vehicle interior wet.

(P. 94)

Electrical malfunction may cause the airbags to deploy or not function

properly, resulting in death or severe injury.

■Cleaning the interior (especially instrument panel)

Do not use polish wax or polish cleaner. The instrument panel may reflect off

the windshield, obstructing the driver's view and leading to an accident,

resulting in death or serious injury.

313

4-1. Maintenance and care

NOTICE

■Cleaning detergents

●Do not use organic substances such as benzene or gasoline, acidic or

alkaline solutions, dye, bleach or other detergent. Doing so may discolor

the vehicle interior or cause streaks or damage to painted surfaces.

●Do not use polish wax or polish cleaner. The instrument panel's or other

interior part’s painted surface may be damaged.

●Do not use a chemical agent containing silicone (highly-polymerized sili-

con compound) when cleaning any of the electrical appliances such as the

air conditioning, all switches and their surrounding areas.

If silicon (highly-polymerized silicon compound) contacts these compo-

nents, it may cause the electrical appliances to malfunction.

■Preventing damage to leather surfaces

Observe the following precautions to avoid damage to and deterioration of

leather surfaces.

●Remove any dust, dirt, sand, oil spots etc. on leather surfaces immedi-

ately.

●Do not expose the vehicle to direct sunlight for extended periods of time.

Park the vehicle in the shade, especially during summer.

●Do not place items made of vinyl, plastic, or that contain wax on the uphol-

stery, as they may stick to the leather surface if the vehicle interior heats

up significantly.

■Water on the floor

Do not wash the vehicle floor with water.

Vehicle systems such as the audio system may be damaged if water comes

into contact with electrical components under the floor of the vehicle, and

may also cause the body to rust.

314

4-1. Maintenance and care

NOTICE

■Cleaning the inside of the rear window

●Be careful not to scratch or damage the heater wires.

●Do not use glass cleaner to clean the rear window, as this may cause

damage to the rear window defogger heater wires. Use a cloth dampened

with lukewarm water to gently wipe the window clean. Wipe the window in

strokes running parallel to the heater wires.

■When cleaning the instrument panel

When small grains of sand and so forth have gotten into instrument panel’s

surface and cannot be wiped away using a cloth, use a clay bar without add-

ing water. Forcibly trying to wipe the surface clean with a brush or sponge

may scratch the surface or fragments of the cloth may be left in the surface.

4

315

4-1. Maintenance and care

®



Cleaning and protecting the Alcantara area

The following procedures will protect and keep your vehicle’s

Alcantara^®upholstery in top condition:

■ Day-to-day cleaning

Perform the following procedures regularly (approximately once

a month).

®

STEP

1

Wipe the entire Alcantara area with a soft cloth that has

been dampened with lukewarm water (approximately 104F

[40C]) and squeezed out.

Do not wipe too hard. Doing so may make the Alcantara^®uphol-

stery surface become uneven. Also, only use a clean cloth.

STEP

2

Once dry, brush the area with a soft brush.

■ Liquid stains

● If liquid is spilled, lightly pat the area with a tissue paper or

similar to soak up the liquid.

®

● When mud, coffee, etc., has dried on the Alcantara uphol-

stery, remove it by lightly brushing the area with a soft brush

or similar.

We recommend using a vacuum cleaner to clean up the area after

the above has been performed.

When a stain cannot be removed using the above procedures,

remove it by performing the following:

STEP

1

Lightly wipe the stained area from the outside to the inside

from multiple angles with a soft cloth that has been damp-

ened with lukewarm water (approximately 104F [40C])

and squeezed out.

Do not wipe the area so strongly that it causes the Alcantara^®

upholstery surface to become uneven. Also, prepare a clean

cloth, and always use a clean area of the cloth.

: If equipped

316

4-1. Maintenance and care

®

STEP

2

3

If the Alcantara upholstery surface becomes uneven,

lightly brush it with a soft brush.

Allow the surface to dry completely.

■ Oil stains

You will need the following items:

● A cloth that has been dampened with benzene

● A dry cloth

STEP

1

Using a dry cloth or tissue paper, wipe away as much of the

oil as possible to prevent the stained area from expanding.

STEP

2

After patting the area from the outside to the inside from

multiple angles using the cloth dampened with benzene,

soak up the oil and benzene that floats up by patting the

area with a dry cloth.

®

STEP

3

If the Alcantara upholstery surface becomes uneven,

4

lightly brush it with a soft brush.

■When removing dirt or dust from the Alcantara^®areas

Remove dirt or dust from the Alcantara^®areas by lighting brushing with a

soft brush. If this does not remove the dirt or dust, remove it using adhesive

tape.

NOTICE

■When soaking up spilled liquids

Do not press down too firmly with the cloth, tissue paper etc., as doing so

may cause the liquid to further penetrate the material, making soaking up

the liquid more difficult.

317

4-2. Maintenance

Maintenance requirements

To ensure safe and economical driving, day-to-day care and regular

maintenance is essential. It is the owner’s responsibility to perform

regular checks. Toyota recommends the following maintenance.

■ General maintenance

Should be performed on a daily basis. This can be done by your-

self or by a Toyota dealer.

■ Scheduled maintenance

Should be performed at specified intervals according to the

maintenance schedule.

For details about maintenance items and schedules, refer to the

“Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

■ Do-it-yourself maintenance

You can perform some maintenance procedures yourself.

Please be aware that do-it-yourself maintenance may affect war-

ranty coverage.

The use of Toyota Repair Manuals is recommended.

For details about warranty coverage, see the separate “Owner’s War-

ranty Information Booklet” or “Owner’s Manual Supplement”.

■Repair and replacement

It is recommended that genuine Toyota parts be used for repair to ensure

performance of each system. If non-Toyota parts are used in replacement or

if a repair shop other than a Toyota dealer performs repairs, confirm the war-

ranty coverage.

318

4-2. Maintenance

■Allow inspection and repairs to be performed by a Toyota dealer

●Toyota technicians are well-trained specialists and are kept up to date

with the latest service information. They are well informed about the

operations of all systems on your vehicle.

●Keep a copy of the repair order. It proves that the maintenance that has

been performed is under warranty coverage. If any problem should arise

while your vehicle is under warranty, your Toyota dealer will promptly

take care of it.

WARNING

■If your vehicle is not properly maintained

It could result in serious damage to the vehicle and possible serious injury or

death.

■Warning in handling of battery

●Engine exhaust, some of its constituents, and a wide variety of automobile

components contain or emit chemicals known to the State of California to

cause cancer and birth defects and other reproductive harm. Work in a

well ventilated area.

4

●Oils, fuels and fluids contained in vehicles as well as waste produced by

component wear contain or emit chemicals known to the State of Califor-

nia to cause cancer and birth defects or other reproductive harm. Avoid

exposure and wash any affected area immediately.

●Battery posts, terminals and related accessories contain lead and lead

compounds which are known to cause brain damage. Wash your hands

after handling. (P. 339)

319

4-2. Maintenance

General maintenance

Listed below are the general maintenance items that should be per-

formed at the intervals specified in the “Owner's Warranty Informa-

tion Booklet” or “Owner’s Manual Supplement/Scheduled

Maintenance Guide”. It is recommended that any problem you notice

should be brought to the attention of your Toyota dealer or qualified

service shop for advice.

Engine compartment

Items

Check points

Check the connections.

Battery

(P. 339)

Brake fluid

At the correct level? (P. 337)

At the correct level? (P. 335)

At the correct level? (P. 332)

No fumes or strange sounds?

Engine coolant

Engine oil

Exhaust system

Not blocked with foreign matter?

Radiator/condenser/hoses

Washer fluid

(P. 337)

At the correct level? (P. 343)

320

4-2. Maintenance

Vehicle interior

Items

Check points

• Moves smoothly (without uneven

pedal effort or catching)?

Accelerator pedal

• Can the vehicle be held securely

on an incline with the shift lever in

P?

Automatic transmission “Park”

mechanism

• Moves smoothly?

• Does it have appropriate clear-

ance and correct amount of free

play?

Brake pedal

Brakes

• Not pull to one side when

applied?

• Loss of brake effectiveness?

• Spongy feeling brake pedal?

• Pedal almost touches floor?

4

Clutch pedal

• Moves smoothly?

• Move smoothly and lock

securely?

Head restraints

Indicators/buzzers

Lights

• Function properly?

• Do all the lights come on?

• Moves smoothly?

Parking brake

• Can hold the vehicle securely on

an incline?

• Does the seat belt system oper-

ate smoothly?

• Are the belts undamaged?

Seat belts

Seats

• Do the seat controls operate

properly?

• Moves smoothly?

Steering wheel

• Has correct free play?

• No strange noises?

321

4-2. Maintenance

Vehicle exterior

Items

Check points

Door/trunk

• Operate smoothly?

Engine hood

• The lock system works properly?

• Is there any leakage after park-

ing?

Fluid leaks

Tire

• Inflation pressure is correct?

• Tire surfaces not worn or dam-

aged?

• Tires rotated according to the

maintenance schedule?

• Wheel nuts are not loose?

• The wiper blades should not show

any signs of cracking, splitting,

wear, contamination or deforma-

tion.

Windshield wipers

• The wiper blades should clear the

windshield without streaking or

skipping.

WARNING

■If the engine is running

Turn the engine off and ensure that there is adequate ventilation before per-

forming maintenance checks.

322

4-2. Maintenance

Emission inspection and maintenance (I/M) programs

Some states have vehicle emission inspection programs which

include OBD (On Board Diagnostics) checks. The OBD system moni-

tors the operation of the emission control system.

■ If the malfunction indicator lamp comes on

The OBD system determines that a problem exists somewhere

in the emission control system. Your vehicle may not pass the I/

M test and may need to be repaired. Contact your Toyota dealer

to service the vehicle.

■ Your vehicle may not pass the I/M test:

● When the battery is disconnected or discharged

Readiness codes that are set during ordinary driving are

erased.

Also, depending on your driving habits, the readiness codes

may not be completely set.

4

● When the fuel tank cap is loose

The malfunction indicator lamp comes on as a temporary mal-

function and your vehicle may not pass the I/M test.

■ When the malfunction indicator lamp goes off after several

driving trips

The error code in the OBD system will not be cleared unless the

vehicle is driven 40 or more times.

■ If your vehicle does not pass the I/M test

Contact your Toyota dealer to prepare the vehicle for re-testing.

323

4-3. Do-it-yourself maintenance

Do-it-yourself service precautions

If you perform maintenance yourself, be sure to follow the correct

procedure as given in these sections.

Items

Parts and tools

• Warm water

• Baking soda

• Grease

Battery condition

(P. 339)

• Conventional wrench

(for terminal clamp bolts)

• Distilled water

• FMVSS No.116 fresh DOT 3

brake fluid

Brake fluid level

(P. 337) • Rag or paper towel

• Funnel (used only for adding

brake fluid)

• “TOYOTA Genuine 50/50 Pre-

mixed Super Long Life Coolant

BLUE” or similar high-quality

ethylene glycol-based non-

silicate, non-amine, non-nitrite

and non-borate coolant with long-

life hybrid organic acid

Engine coolant level

(P. 335)

technology.

“TOYOTA Genuine 50/50 Pre-

mixed Super Long Life Coolant

BLUE” is pre-mixed with 50%

coolant and 50% deionized

water.

• Funnel (used only for adding

engine coolant)

• “Toyota Genuine Motor Oil” or

equivalent

• Rag or paper towel, funnel (used

only for adding engine oil)

Engine oil level

(P. 332)

324

4-3. Do-it-yourself maintenance

Items

Parts and tools

• Fuse with same amperage rating

as original

Fuses

(P. 367)

(P. 375)

• Bulb with same number and watt-

age rating as original

• Phillips-head screwdriver

• Flathead screwdriver

Light bulbs

Radiator and condenser



(P. 337)

• Tire pressure gauge

• Compressed air source

Tire inflation pressure (P. 353)

• Water washer fluid containing

antifreeze (for winter use)

• Funnel

Washer fluid

(P. 343)

4

325

4-3. Do-it-yourself maintenance

WARNING

The engine compartment contains many mechanisms and fluids that may

move suddenly, become hot, or become electrically energized. To avoid death

or serious injury, observe the following precautions.

■When working on the engine compartment

●Keep hands, clothing, and tools away from the moving fan and engine

drive belt.

●Be careful not to touch the engine, radiator, exhaust manifold, etc. right

after driving as they may be hot. Oil and other fluids may also be hot.

●Do not leave anything that may burn easily, such as paper or rags, in the

engine compartment.

●Do not smoke, cause sparks or expose an open flame to fuel or the bat-

tery. Fuel and battery fumes are flammable.

●Be extremely cautious when working on the battery. It contains poisonous

and corrosive sulfuric acid.

■When working near the electric cooling fans or radiator grille

Vehicles without a smart key system: Be sure the engine switch is off. With

the engine switch in the “ON” position, the electric cooling fans may auto-

matically start to run if the air conditioning is on and/or the coolant tempera-

ture is high. (P. 337)

Vehicles with a smart key system: Be sure the “ENGINE START STOP”

switch is off. With the “ENGINE START STOP” switch in IGNITION ON

mode, the electric cooling fans may automatically start to run if the air condi-

tioning is on and/or the coolant temperature is high. (P. 337)

■Safety glasses

Wear safety glasses to prevent flying or falling material, fluid spray, etc. from

getting in the eyes.

NOTICE

■If you remove the air cleaner filter

Driving with the air cleaner filter removed may cause excessive engine wear

due to dirt in the air.

326

4-3. Do-it-yourself maintenance

Hood

Release the lock from the inside of the vehicle to open the hood.

Pull the hood release lever.

The hood will pop up slightly.

STEP

1

Push the auxiliary catch lever

to the left and lift the hood.

STEP

2

4

Hold the hood open by insert-

ing the supporting rod into the

slot.

STEP

3

When holding the supporting

rod, hold it by the grip portion.

Grip

327

4-3. Do-it-yourself maintenance

WARNING

■Pre-driving check

Check that the hood is fully closed and locked.

If the hood is not locked properly it may open while the vehicle is in motion

and cause an accident, which may result in death or serious injury.

NOTICE

■When opening the hood

●Do not lift up or operate the wipers. Doing so may cause the hood and wip-

ers to contact, scratching the hood.

●Use caution when opening the hood in windy weather as it may close sud-

denly in strong wind.

●Do not attach any accessories other than genuine Toyota products to the

hood. Such additional weight on the hood may cause it to be too heavy to

be supported by the supporting rod when opened.

■When closing the hood

Do not apply excessive weight or force when closing the hood as doing so

may result in damage.

328

4-3. Do-it-yourself maintenance

Positioning a floor jack

When raising your vehicle with a floor jack, position the jack cor-

rectly. Improper placement may damage your vehicle or cause injury.

■ Front

■ Rear

4

329

4-3. Do-it-yourself maintenance

WARNING

■When raising your vehicle

Make sure to observe the following precautions to reduce the possibility of

death or serious injury:

●Lift up the vehicle using a floor jack

such as the one shown in the illustra-

tion.

●When using a floor jack, follow the instructions of the manual provided with

the jack.

●Do not use the jack that was supplied with your vehicle.

●Do not put any part of your body underneath the vehicle when it is sup-

ported only by the floor jack.

●Always use floor jack and/or automotive jack stands on a solid, flat, level

surface.

●Do not start the engine while the vehicle is supported by the floor jack.

●Stop the vehicle on level, firm ground, firmly set the parking brake and shift

the shift lever to P (vehicles with an automatic transmission) or R (vehicles

with a manual transmission).

●Make sure to set the floor jack properly at the jack point.

Raising the vehicle with an improperly positioned floor jack will damage

the vehicle and may cause the vehicle to fall off the floor jack.

●Do not raise the vehicle while someone is in the vehicle.

●When raising the vehicle, do not place any object on top of or underneath

the floor jack.

●When raising the vehicle, ensure that there is sufficient surrounding space.

The vehicle’s position may change slightly when lowered.

330

4-3. Do-it-yourself maintenance

Engine compartment

4

Battery

Engine oil level dipstick

(P. 332)

Brake fluid reservoir

(P. 337)

Engine oil filler cap

(P. 333)

(P. 339)

Washer fluid tank

(P. 343)

Electric cooling fans

Condenser

Radiator

(P. 337)

Engine coolant reservoir

(P. 335)

(P. 367)

Fuse box

331

4-3. Do-it-yourself maintenance

Engine oil

With the engine at operating temperature and turned off, check the oil

level on the dipstick.

■ Checking the engine oil

STEP

1

Park the vehicle on level ground. After warming up the engine

and turning it off, wait more than five minutes for the oil to

drain back into the bottom of the engine.

Hold a rag under the end and

pull the dipstick out.

STEP

2

STEP

3

4

5

Wipe the dipstick clean.

Reinsert the dipstick fully.

Holding a rag under the end, pull the dipstick out and check

the oil level.

When checking the oil, look at both sides of the dipstick and use the

lower measurement to determine the level of oil.

STEP

6

Wipe the dipstick and reinsert it fully.

Low

Full

332

4-3. Do-it-yourself maintenance

■ Adding engine oil

If the oil level is below or near

the low level mark, add engine

oil of the same type as already in

the engine.

Make sure to check the oil type and prepare the items needed before

adding oil.

Engine oil

P. 462

selection

Oil quantity

1.1 qt. (1.0 L, 0.9 Imp. qt.)

(Low  Full)

4

Items

Clean funnel

STEP

1

2

3

Remove the oil filler cap by turning it counterclockwise.

Add engine oil slowly, checking the dipstick.

Install the oil filler cap by turning it clockwise.

333

4-3. Do-it-yourself maintenance

■Engine oil consumption

A certain amount of engine oil will be consumed while driving. In the follow-

ing situations, oil consumption may increase, and engine oil may need to be

refilled in between oil maintenance intervals.

●When the engine is new, for example directly after purchasing the vehicle

or after replacing the engine

●If low quality oil or oil of an inappropriate viscosity is used

●When driving at high engine speeds or with a heavy load, or when driving

while accelerating or decelerating frequently

●When leaving the engine idling for a long time, or when driving frequently

through heavy traffic

WARNING

■Used engine oil

●Used engine oil contains potentially harmful contaminants which may

cause skin disorders such as inflammation or skin cancer, so care should

be taken to avoid prolonged and repeated contact. To remove used engine

oil from your skin, wash thoroughly with soap and water.

●Dispose of used oil and filters only in a safe and acceptable manner. Do

not dispose of used oil and filters in household trash, in sewers or onto the

ground.

Call your Toyota dealer, service station or auto parts store for information

concerning recycling or disposal.

●Do not leave used engine oil within the reach of children.

334

4-3. Do-it-yourself maintenance

NOTICE

■To prevent serious engine damage

Check the oil level on a regular basis.

■When replacing the engine oil

●Be careful not to spill engine oil on the vehicle components.

●Avoid overfilling, or the engine could be damaged.

●Check the oil level on the dipstick every time you refill the vehicle.

●Be sure the engine oil filler cap is properly tightened.

Engine coolant

The coolant level is satisfactory if it is between the “FULL” and “LOW”

lines on the reservoir when the engine is cold.

Reservoir cap

“FULL”

4

“LOW”

If the level is on or below the

“LOW” line, add coolant up to the

“FULL” line.

■If the coolant level drops within a short time after replenishing

Visually check the radiator, hoses, engine coolant filler cap, radiator cap,

drain cock and water pump.

If you cannot find a leak, have your Toyota dealer pressure test the cap and

check for leaks in the cooling system.

335

4-3. Do-it-yourself maintenance

■Coolant selection

Only use “TOYOTA Genuine 50/50 Pre-mixed Super Long Life Coolant

BLUE” or similar high-quality ethylene glycol-based non-silicate, non-amine,

non-nitrite, and non-borate coolant with long-life hybrid organic acid technol-

ogy.

“TOYOTA Genuine 50/50 Pre-mixed Super Long Life Coolant BLUE” is a

mixture of 50% coolant and 50% deionized water. (Enabled: -31F [-35C])

For more details about engine coolant, contact your Toyota dealer.

WARNING

■When the engine is hot

Do not remove the radiator cap.

The cooling system may be under pressure and may spray hot coolant if the

cap is removed, causing serious injuries, such as burns.

NOTICE

■When adding engine coolant

Coolant is neither plain water nor straight antifreeze. The correct mixture of

water and antifreeze must be used to provide proper lubrication, corrosion

protection and cooling. Be sure to read the antifreeze or coolant label.

■If you spill coolant

Be sure to wash it off with water to prevent it from damaging parts or paint.

336

4-3. Do-it-yourself maintenance

Radiator and condenser

Check the radiator and condenser and clear away any foreign

objects.

If either of the above parts are extremely dirty or you are not sure of

their condition, have your vehicle checked by your Toyota dealer.

WARNING

■When the engine is hot

Do not touch the radiator or condenser as they may be hot and cause seri-

ous injuries, such as burns.

Brake fluid

■ Checking fluid level

4

The brake fluid level should be

between the “MAX” and “MIN”

lines on the tank.

“MAX”

“MIN”

337

4-3. Do-it-yourself maintenance

■ Adding fluid

Make sure to check the fluid type and prepare the necessary items.

Fluid type

Items

SAE J1703 or FMVSS No.116 DOT 3

Clean funnel

■Brake fluid can absorb moisture from the air

Excess moisture in the fluid can cause a dangerous loss of braking effi-

ciency. Use only newly opened brake fluid.

WARNING

■When filling the reservoir

Take care because brake fluid can harm your hands or eyes and damage

painted surfaces.

If fluid gets in your eyes, flush your eyes with clean water immediately.

If you still experience discomfort, see a doctor.

NOTICE

■If the fluid level is low or high

It is normal for the brake fluid level to go down slightly as the brake pads

wear or when the fluid level in the accumulator is high.

If the reservoir needs frequent refilling, it may indicate a serious problem.

338

4-3. Do-it-yourself maintenance

Battery

Check the battery as follows.

■ Battery exterior

Make sure that the battery terminals are not corroded and that

there are no loose connections, cracks, or loose clamps.

Hold-down clamp

Terminals

■ Checking battery fluid

4

Check that the level is between

“UPPER LEVEL” and “LOWER

LEVEL”.

“UPPER LEVEL”

“LOWER LEVEL”

If the fluid level is at or below

“LOWER LEVEL”, add distilled

water.

339

4-3. Do-it-yourself maintenance

■ Adding distilled water

Low

O.K.

STEP

1

Remove the vent plug.

Add distilled water.

2

If the “UPPER LEVEL” line cannot be seen, check the fluid level by

looking directly at the cell.

STEP

3

Put the vent plug back on and close securely.

■Before recharging

When recharging, the battery produces hydrogen gas which is flammable

and explosive. Therefore, before recharging:

●If recharging with the battery installed on the vehicle, be sure to discon-

nect the ground cable.

●Make sure the power switch on the charger is off when connecting and

disconnecting the charger cables to the battery.

340

4-3. Do-it-yourself maintenance

■After recharging/reconnecting the battery (vehicles with a smart key

system)

●Unlocking the doors using the smart key system may not be possible

immediately after reconnecting the battery. If this happens, use the wire-

less remote control or the mechanical key to lock/unlock the doors.

●Start the engine with the “ENGINE START STOP” switch in ACCES-

SORY mode. The engine may not start with the “ENGINE START STOP”

switch turned off. However, the engine will operate normally from the sec-

ond attempt.

●The “ENGINE START STOP” switch mode is recorded by the vehicle. If

the battery is reconnected, the vehicle will return the “ENGINE START

STOP” switch mode to the status it was in before the battery was discon-

nected. Make sure to turn off the engine before disconnect the battery.

Take extra care when connecting the battery if the “ENGINE START

STOP” switch mode prior to discharge is unknown.

If the engine will not start even after multiple attempts, contact your Toyota

dealer.

4

341

4-3. Do-it-yourself maintenance

WARNING

■Chemicals in the battery

A battery contains poisonous and corrosive sulfuric acid and may produce

hydrogen gas which is flammable and explosive. To reduce the risk of death

or serious injury, take the following precautions while working on or near the

battery:

●Do not cause sparks by touching the battery terminals with tools.

●Do not smoke or light a match near the battery.

●Avoid contact with eyes, skin and clothes.

●Never inhale or swallow electrolyte.

●Wear protective safety glasses when working near the battery.

●Keep children away from the battery.

■Where to safely charge the battery

Always charge the battery in an open area. Do not charge the battery in a

garage or closed room where there is not sufficient ventilation.

■Emergency measures regarding electrolyte

●If electrolyte gets in your eyes

Flush your eyes with clean water for at least 15 minutes and get immedi-

ate medical attention. If possible, continue to apply water with a sponge or

cloth while traveling to the nearest medical facility.

●If electrolyte gets on your skin

Wash the affected area thoroughly. If you feel pain or burning, get medical

attention immediately.

●If electrolyte gets on your clothes

It can soak through clothing on to your skin. Immediately take off the cloth-

ing and follow the procedure above if necessary.

●If you accidentally swallow electrolyte

Drink a large quantity of water or milk. Get emergency medical attention

immediately.

342

4-3. Do-it-yourself maintenance

NOTICE

■When recharging the battery

Never recharge the battery while the engine is running. Also, be sure all

accessories are turned off.

■When adding distilled water

Avoid overfilling. Water spilled during battery recharging may cause corro-

sion.

Washer fluid

If the washer fluid level is at

“LOW”, add washer fluid.

4

■Using the gauge

The washer fluid level can be checked by

observing the position of the level on the

liquid-covered holes in the gauge.

If the level falls below the second hole

from the bottom (the “LOW” position),

Current

fluid level

refill the washer fluid.

CTH43AS134

343

4-3. Do-it-yourself maintenance

WARNING

■When adding washer fluid

Do not add washer fluid when the engine is hot or running, as washer fluid

contains alcohol and may catch fire if spilled on the engine etc.

NOTICE

■Washer fluid

Do not use soapy water or engine antifreeze instead of washer fluid.

Doing so may cause streaking on the vehicle’s painted surfaces, as well as

damaging the pump leading to problems of the washer fluid not spraying.

■Diluting washer fluid

Dilute washer fluid with water as necessary.

Refer to the freezing temperatures listed on the label of the washer fluid bot-

tle.

344

4-3. Do-it-yourself maintenance

Tires

Replace or rotate tires in accordance with maintenance sched-

ules and treadwear.

■ Checking tires

Check if the treadwear indicators are showing on the tires. Also

check the tires for uneven wear, such as excessive wear on one

side of the tread.

Check the spare tire condition and pressure if not rotated.

4

New tread

Worn tread

Treadwear indicator

The location of treadwear indicators is shown by a “TWI” or “” mark,

etc., molded into the sidewall of each tire.

Replace the tires if the treadwear indicators are showing on a tire.

■ Tire rotation

Rotate the tires in the order

shown.

To equalize tire wear and

extend tire life, Toyota recom-

mends that tire rotation is

carried out at the same inter-

val as tire inspection.

Front

345

4-3. Do-it-yourself maintenance

■ The tire pressure warning system

Your Toyota is equipped with a tire pressure warning system that

uses tire pressure warning valves and transmitters to detect low

tire inflation pressure before serious problems arise.

(P. 399)

Installing tire pressure warning valves and transmitters

When replacing tires or wheels, tire pressure warning valves and

transmitters must also be installed.

When new tire pressure warning valves and transmitters are

installed, new tire pressure warning valve and transmitter ID codes

must be registered in the tire pressure warning computer and tire

pressure warning system must be initialized. Have tire pressure

warning valve and transmitter ID codes registered by your Toyota

dealer. (P. 346)

Registering ID codes

The tire pressure warning valve and transmitter is equipped with a

unique ID code. When replacing a tire pressure warning valve and

transmitter, it is necessary to register the ID code. Have the ID code

registered by your Toyota dealer.

346

4-3. Do-it-yourself maintenance

■When to replace your vehicle’s tires

Tires should be replaced if:

●The treadwear indicators are showing on a tire.

●You have tire damage such as cuts, splits, cracks deep enough to

expose the fabric or bulges indicating internal damage

●A tire goes flat repeatedly or cannot be properly repaired due to the

size or location of a cut or other damage

If you are not sure, consult with your Toyota dealer.

■Replacing tires and wheels

If the ID code of the tire pressure warning valve and transmitter is not

registered, the tire pressure warning system will not work properly. After

driving for about 20 minutes, the tire pressure warning light comes on

after blinking for 1 minute to indicate a system malfunction.

■Tire life

Any tire over 6 years old must be checked by a qualified technician even

if they have seldom or never been used or damage is not obvious.

4

■If the tread wears down below 0.16 in. (4 mm) on snow tires

The effectiveness of snow tires is lost.

■Low profile tires

Generally, low profile tires will wear more rapidly and tire grip perfor-

mance will be reduced on snowy and/or icy roads when compared to

standard tires. Be sure to use snow tires or tire chains on snowy and/or

icy roads and drive carefully at a speed appropriate for road and weather

conditions.

347

4-3. Do-it-yourself maintenance

■Maximum load of tire

Check that the maximum load of the replacement tire is greater than 1/2

of the Gross Axle Weight Ratings (GAWR) of either the front axle or the

rear axle, whichever is greater.

For the GAWR, see the Certification

Label. For the maximum load of the

tire, see the load limit at maximum cold

tire inflation pressure mentioned on the

sidewall of the tire. (P. 474)

■Tire types

1 Summer tires

Summer tires are high-speed performance tires best suited to highway

driving under dry conditions. Since summer tires do not have the same

traction performance as snow tires, summer tires are inadequate for

driving on snow-covered or icy roads. For driving on snow-covered

roads or icy roads, the use of snow tires is recommended. When

installing snow tires, be sure to replace all four tires.

2 All season tires

All season tires are designed to provide better traction in snow and to

be adequate for driving in most winter conditions, as well as for use

year round. All season tires, however, do not have adequate traction

performance compared with snow tires in heavy or loose snow. Also,

all season tires fall short in acceleration and handling performance

compared with summer tires in highway driving.

3 Snow tires

For driving on snow-covered roads or icy roads, we recommend using

snow tires. If you need snow tires, select tires of the same size, con-

struction and load capacity as the originally installed tires. Since your

vehicle has radial tires as original equipment, make sure your snow

tires also have radial construction. Do not install studded tires without

first checking local regulations for possible restriction. Snow tires

should be installed on all wheels. (P. 261)

348

4-3. Do-it-yourself maintenance

■Initializing the tire pressure warning system

Initialize the system with the tire inflation pressure adjusted to the speci-

fied level.

■Routine tire inflation pressure checks

The tire pressure warning system does not replace routine tire inflation

pressure checks. Make sure to check tire inflation pressure as part of

your routine of daily vehicle checks.

■Tire pressure warning system certification (vehicles without a

smart key system)

MODEL/FCC IDs:

Transmitter: PAXPMVC010

Receiver: HYQ23AAC

For vehicles sold in the U.S.A.

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

4

FCC WARNING:

Changes or modifications not expressly approved by the party responsi-

ble for compliance could void the user's authority to operate the equip-

ment.

For vehicles sold in Canada

NOTE:

This device complies with Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions: (1) This device may

not cause interference; and (2) This device must accept any interfer-

ence, including interference that may cause undesired operation of the

device.

NOTE:

Le présent appareil est conforme aux CNR d’Industrie Canada applica-

bles aux appareils radio exempts de licence. L’exploitation est autorisée

aux deux conditions suivantes: (1) l’appareil ne doit pas produire de

brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d’en compro-

mettre le fonctionnement.

349

4-3. Do-it-yourself maintenance

■Tire pressure warning system certification (vehicles with a smart

key system)

MODEL/FCC IDs:

Transmitter: PAXPMVC010

Receiver: HYQ23AAE

For vehicles sold in the U.S.A.

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC WARNING:

Changes or modifications not expressly approved by the party responsi-

ble for compliance could void the user's authority to operate the equip-

ment.

For vehicles sold in Canada

NOTE:

This device complies with Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions: (1) This device may

not cause interference; and (2) This device must accept any interfer-

ence, including interference that may cause undesired operation of the

device.

NOTE:

Le présent appareil est conforme aux CNR d’Industrie Canada applica-

bles aux appareils radio exempts de licence. L’exploitation est autorisée

aux deux conditions suivantes: (1) l’appareil ne doit pas produire de

brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d’en compro-

mettre le fonctionnement.

350

4-3. Do-it-yourself maintenance

WARNING

■Tire pressure warning system operation

The tire pressure warning system may not provide warning immediately

if a tire bursts or if sudden air leakage occurs.

■When inspecting or replacing tires

Observe the following precautions to prevent accidents.

Failure to do so may cause damage to parts of the drive train, as well as

dangerous handling characteristics, which may lead to an accident

resulting in death or serious injury.

●Make sure to install 4 tires that are of the specified size, and that all 4

tires are the same size, same maker, same brand and tread pattern.

●Do not use tire sizes other than those recommended by Toyota.

●Only use radial tires.

●Do not mix summer, all season and snow tires.

●Do not use tires that have been used on another vehicle.

Do not use tires if you do not know how they were used previously.

4

NOTICE

■Repairing or replacing tires, wheels, tire pressure warning valves,

transmitters and tire valve caps

●When removing or fitting the wheels, tires or the tire pressure warning

valves and transmitters, contact your Toyota dealer as the tire pres-

sure warning valves and transmitters may be damaged if not handled

correctly.

●Make sure to install the tire valve caps. If the tire valve caps are not

installed, water could enter the tire pressure warning valves and the

tire pressure warning valves could be bound.

●When replacing tire valve caps, do not use tire valve caps other than

those specified. The cap may become stuck.

351

4-3. Do-it-yourself maintenance

NOTICE

■Driving on rough roads

Take particular care when driving on roads with loose surfaces or pot

holes.

These conditions may cause losses in tire inflation pressure, reducing

the cushioning ability of the tires. In addition, driving on rough roads may

cause damage to the tires themselves, as well as the vehicle’s wheels

and body.

■Low profile tires and wheels

Low profile tires may cause greater damage than usual to the tire wheel

when receiving impact from the road surface. Therefore pay attention to

the following:

●Be sure to use proper tire inflation pressure. If tires are under-inflated,

they may be damaged more severely.

●Avoid pot holes, uneven pavement, curbs and other road hazards.

Failure to do so may lead to severe tire and wheel damage.

■If tire inflation pressures become low while driving

Do not continue driving, or your tires and/or wheels may be ruined.

352

4-3. Do-it-yourself maintenance

Tire inflation pressure

■ Tire inflation pressure

The recommended cold tire inflation pressure and tire size is dis-

played on the tire and loading information label. (P. 468)

4

353

4-3. Do-it-yourself maintenance

■ Inspection and adjustment procedure

Tire valve

Tire pressure gauge

STEP

1

2

3

4

Remove the tire valve cap.

Press the tip of the tire pressure gauge onto the tire valve.

Read the pressure using the graduations of the gauge.

If the tire inflation pressure is not within the recommended

levels, adjust the pressure.

If you add too much air, press the center of the valve to

lower.

STEP

5

6

After completing the tire inflation pressure measurement

and adjustment, apply soapy water to the valve and check

for leakage.

Reinstall the tire valve cap.

■Tire inflation pressure check interval

You should check tire inflation pressure every two weeks, or at least

once a month.

Do not forget to check the spare.

354

4-3. Do-it-yourself maintenance

■Effects of incorrect tire inflation pressure

Driving with incorrect tire inflation pressure may result in the following:

●Reduced fuel economy

●Reduced driving comfort and poor handling

●Reduced tire life due to wear

●Reduced safety

●Damage to the drive train

If a tire needs frequent refilling, have it checked by your Toyota dealer.

■Instructions for checking tire inflation pressure

When checking tire inflation pressure, observe the following:

●Check only when the tires are cold.

If your vehicle has been parked for at least 3 hours and has not been

driven for more than 1 mile or 1.5 km, you will get an accurate cold

tire inflation pressure reading.

●Always use a tire pressure gauge.

It is difficult to judge if a tire is properly inflated based only on its

appearance.

4

●It is normal for the tire inflation pressure to be higher after driving as

heat is generated in the tire. Do not reduce tire inflation pressure after

driving.

●Never exceed the vehicle capacity weight.

Passengers and luggage weight should be placed so that the vehicle

is balanced.

355

4-3. Do-it-yourself maintenance

WARNING

■Proper inflation is critical to save tire performance

Keep your tires properly inflated.

If the tires are not properly inflated, the following conditions may occur

which could lead to an accident resulting in death or serious injury:

●Excessive wear

●Uneven wear

●Poor handling

●Possibility of blowouts resulting from overheated tires

●Air leaking from between tire and wheel

●Wheel deformation and/or tire damage

●Greater possibility of tire damage while driving (due to road hazards,

expansion joints, sharp edges in the road, etc.)

NOTICE

■When inspecting and adjusting tire inflation pressure

Be sure to reinstall the tire valve caps.

If a valve cap is not installed, dirt or moisture may get into the valve and

cause an air leak, resulting in decreased tire inflation pressure.

356

4-3. Do-it-yourself maintenance

Wheels

If a wheel is bent, cracked or heavily corroded, it should be

replaced. Otherwise, the tire may separate from the wheel or

cause loss of handling control.

■ Wheel selection

When replacing wheels, care should be taken to ensure that

they are equivalent to those removed in load capacity, diameter,

rim width, and inset*.

Replacement wheels are available at your Toyota dealer.

*: Conventionally referred to as “offset”.

Toyota does not recommend using:

● Wheels of different sizes or types

● Used wheels

● Bent wheels that have been straightened

■ Aluminum wheel precautions

4

● Use only Toyota wheel nuts and wrenches designed for use

with your aluminum wheels.

● When rotating, repairing or changing your tires, check that the

wheel nuts are still tight after driving 1000 miles (1600 km).

● Be careful not to damage the aluminum wheels when using

tire chains.

● Use only Toyota genuine balance weights or equivalent and a

plastic or rubber hammer when balancing your wheels.

357

4-3. Do-it-yourself maintenance

■When replacing wheels

The wheels of your Toyota are equipped with tire pressure warning

valves and transmitters that allow the tire pressure warning system to

provide advanced warning in the event of a loss in tire inflation pressure.

Whenever wheels are replaced, the tire pressure warning valves and

transmitters must be installed. (P. 346)

WARNING

■When replacing wheels

●Do not use wheels that are a different size from those recommended in

the Owner’s Manual, as this may result in loss of handling control.

●Never use an inner tube in a leaking wheel which is designed for a

tubeless tire. Doing so may result in an accident, causing death or seri-

ous injury.

■When installing the wheel nuts

●Be sure to install the wheel nuts with

the tapered ends facing inward.

Installing the nuts with the tapered

ends facing outward can cause the

wheel to break and eventually cause

the wheel to come off while driving,

which could lead to an accident

resulting in death or serious injury.

Tapered portion

●Never use oil or grease on the wheel bolts or wheel nuts.

Oil and grease may cause the wheel nuts to be excessively tightened,

leading to bolt or disc wheel damage. In addition, the oil or grease can

cause the wheel nuts to loosen and the wheel may fall off, causing an

accident and resulting in death or serious injury. Remove any oil or

grease from the wheel bolts or wheel nuts.

358

4-3. Do-it-yourself maintenance

NOTICE

■Replacing tire inflation pressure warning valves and transmitters

●Because tire repair or replacement may affect the tire pressure warn-

ing valves and transmitters, make sure to have tires serviced by your

Toyota dealer or other qualified service shop. In addition, make sure to

purchase your tire pressure warning valves and transmitters at your

Toyota dealer.

●Ensure that only genuine Toyota wheels are used on your vehicle.

Tire pressure warning valves and transmitters may not work properly

with non-genuine wheels.

4

359

4-3. Do-it-yourself maintenance

Air conditioning filter

The air conditioning filter must be changed regularly to maintain air

conditioning efficiency.

■ Removal method

STEP

1

Vehicles without a smart key system

Turn the engine switch off.

Vehicles with a smart key system

Turn the “ENGINE START STOP” switch off.

Open the glove box. Slide off

STEP

2

the damper.

Push in each side of the glove

box and pull the glove box

toward you to disconnect the

claws.

STEP

3

360

4-3. Do-it-yourself maintenance

Lower the glove box slowly

STEP

4

until surface

is horizontal

with the floor, then pull it out.

(Simply pulling with gentle

force will disengage the lower

claws.)

Lower claw

Lower claw engagement

point

Do not forcibly pull the glove

box. Otherwise, the lower

claws or the lower claw

engagement points may be

deformed, making it difficult to

reinstall or close the glove box.

4

Remove the filter cover.

STEP

5

Remove the air conditioning

filter and replace it with a new

one.

STEP

6

The “UP” marks shown on

the filter should be pointing up.

STEP

7

When installing, reverse the steps listed.

361

4-3. Do-it-yourself maintenance

■Checking interval

Inspect and replace the air conditioning filter according to the maintenance

schedule. In dusty areas or areas with heavy traffic flow, early replacement

may be required. (For scheduled maintenance information, please refer to

the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

■If air flow from the vents decreases dramatically

The filter may be clogged. Check the filter and replace if necessary.

NOTICE

■When removing the glove box

Do not forcibly pull the glove box. Otherwise, the lower claws or the lower

claw engagement points may be deformed, making it difficult to reinstall or

close the glove box.

■When using the air conditioning system

Make sure that a filter is always installed.

Using the air conditioning system without a filter may cause damage to the

system.

362

4-3. Do-it-yourself maintenance

Wireless remote control/electronic key battery

Replace the battery with a new one if it is depleted.

■ You will need the following items:

● Flathead screwdriver

● Lithium battery CR2016 (vehicles without a smart key sys-

tem), or CR2032 (vehicles with a smart key system)

■ Replacing the battery (vehicles without a smart key system)

Remove the cover.

STEP

1

To prevent damage to the key,

cover the tip of the screwdriver

with a rag.

To prevent the buttons from

being disassembled, face the

button surface downward.

4

Remove the module.

STEP

2

Open the case cover using a

coin protected with tape etc.

and remove the depleted bat-

tery.

STEP

3

Insert a new battery with the

“+” terminal facing up.

363

4-3. Do-it-yourself maintenance

■ Replacing the battery (vehicles with a smart key system)

Take out the mechanical key.

STEP

1

Remove the cover.

STEP

2

To prevent damage to the key,

cover the tip of the screwdriver

with a rag.

Remove the depleted battery.

STEP

3

Insert a new battery with the

“+” terminal facing up.

364

4-3. Do-it-yourself maintenance

■Use a CR2016 (vehicles without a smart key system) or CR2032 (vehi-

cles with a smart key system) lithium battery

●Batteries can be purchased at your Toyota dealer, local electrical appli-

ance shops or camera stores.

●Replace only with the same or equivalent type recommended by the

manufacturer.

●Dispose of used batteries according to local laws.

■If the key battery is depleted

The following symptoms may occur:

●The smart key system (if equipped) and wireless remote control will not

function properly.

●The operational range will be reduced.

■When putting the module back (vehicles without a smart key system)

Insert the module from directly above.

Inserting it on an angle may prevent the

key buttons from operating properly.

4

WARNING

■Removed battery and other parts

These parts are small and if swallowed by a child, they can cause choking.

Keep away from children. Failure to do so could result in death or serious

injury.

365

4-3. Do-it-yourself maintenance

NOTICE

■For normal operation after replacing the battery

Observe the following precautions to prevent accidents:

●Always work with dry hands.

Moisture may cause the battery to rust.

●Do not touch or move any other component inside the remote control.

●Do not bend either of the battery terminals.

366

4-3. Do-it-yourself maintenance

Checking and replacing fuses

If any of the electrical components do not operate, a fuse may have

blown. If this happens, check and replace the fuses as necessary.

STEP

1

Vehicles without a smart key system

Turn the engine switch off.

Vehicles with a smart key system

Turn the “ENGINE START STOP” switch off.

STEP

2

Open the fuse box cover.

Engine compartment

Push the tabs in and lift the lid

off.

4

Instrument panel

Remove the lid.

367

4-3. Do-it-yourself maintenance

STEP

3

4

After a system failure, see “Fuse layout and amperage rat-

ings” (P. 370) for details about which fuse to check.

Remove the fuse with the pull-

out tool.

STEP

5

Check if the fuse has blown.

Type A

Normal fuse

Blown fuse

Replace it with one of an

appropriate amperage rating.

The amperage rating can be

found on the fuse box lid.

Type B

Normal fuse

Blown fuse

Replace it with one of an

appropriate amperage rating.

The amperage rating can be

found on the fuse box lid.

368

4-3. Do-it-yourself maintenance

Type C

Normal fuse

Blown fuse

Contact your Toyota dealer.

Type D

Normal fuse

Blown fuse

Contact your Toyota dealer.

4

369

4-3. Do-it-yourself maintenance

Fuse layout and amperage ratings

■ Engine compartment

Fuse

MIR HTR

RDI

Ampere

7.5 A

25 A

7.5 A

40 A

50 A

10 A

30 A

10 A

25 A

Circuit

Outside rear view mirror defoggers

Electric cooling fan

Engine control unit

ABS

1

2

3

4

5

6

7

8

9

(PUSH-AT)

ABS NO. 1

HEATER

WASHER

WIPER

Air conditioning system

Windshield washer

Windshield wipers

Rear window defogger



RR DEF

(RR FOG)

10 D FR DOOR

11 (CDS)

Power window (driver’s side)

Electric cooling fan



12 D-OP

13 ABS NO. 2

14 D FL DOOR

15 SPARE

ABS

Power window (passenger’s side)

See note. Spare fuse

370

4-3. Do-it-yourself maintenance

Fuse

16 SPARE

17 SPARE

18 SPARE

19 SPARE

20 SPARE

21 ST

Ampere

Circuit

See note. Spare fuse

7.5 A

20 A

15 A

7.5 A

15 A

Starting system

22 ALT-S

Charging system

Steering lock system

Power door lock

Engine control unit

Transmission

23 (STR LOCK)

24 D/L

25 ETCS

26 (AT+B)

27 (AM2 NO. 2)

28 EFI (CTRL)

Smart key system

Engine control unit

4

Multiport fuel injection system/

sequential multiport fuel injection

system

29 EFI (HTR)

15 A

30 EFI (IGN)

31 EFI (+B)

15 A

Starting system

7.5 A

Engine control unit

Turn signal lights, emergency

flashers

32 HAZ

15 A

Automatic air conditioning system,

gauge and meters

33 MPX-B

7.5 A

Multiport fuel injection system/

sequential multiport fuel injection

system

34 F/PMP

20 A

SRS airbag system, engine control

unit

35 IG2 MAIN

36 DCC

30 A

Interior light, wireless remote con-

trol, main body ECU

371

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

37 HORN NO. 2

38 HORN NO. 1

39 H-LP LH LO

40 H-LP RH LO

41 H-LP LH HI

42 H-LP RH HI

7.5 A

15 A

10 A

Horn

Left-hand headlight (low beam)

Right-hand headlight (low beam)

Left-hand headlight (high beam)

Right-hand headlight (high beam)

Multiport fuel injection system/

sequential multiport fuel injection

system

43 INJ

30 A

44 H-LP WASHER

45 AM2 NO. 1

46 EPS

30 A

40 A

80 A

15 A



Starting system, engine control unit

Electric power steering

SRS airbag system

47 A/B MAIN

Wireless remote control, main body

ECU

48 ECU-B

7.5 A

49 DOME

50 IG2

20 A

Interior light

7.5 A

Engine control unit

Note

One of each of the following spare fuses are provided: 7.5 A, 10 A, 15

A, 20 A, 25 A, 30 A.

372

4-3. Do-it-yourself maintenance

■ Instrument panel

Fuse

Ampere

10 A

Circuit

Main body ECU, outside rear view

mirrors

1

ECU ACC

2

3

4

5

6

7

8

9

P/POINT No.2

PANEL

TAIL

15 A

10 A

7.5 A

10 A

7.5 A

10 A

7.5 A

15 A

Power outlet

Illumination

Tail lights

DRL

Daytime running light system

Inside rear view mirror

Stop lights

4

UNIT IG1

STOP

OBD

On-board diagnosis system

Air conditioning system

Left-hand front fog light

Right-hand front fog light

Back-up lights

HEATER-S

10 HEATER

11 FR FOG LH

12 FR FOG RH

13 BK/UP LP

14 ECU IG1

15 AM1

ABS, electric power steering

Starting system

16 AMP

Audio system

17 AT UNIT

Transmission

Gauge and meters, smart key sys-

tem

18 GAUGE

7.5 A

19 ECU IG2

10 A

7.5 A

15 A

Engine control unit

Left-hand seat heater

Right-hand seat heater

Audio system

20 SEAT HTR LH

21 SEAT HTR RH

22 RADIO

23 P/POINT No.1

Power outlet

373

4-3. Do-it-yourself maintenance

■After a fuse is replaced

●If the lights do not turn on even after the fuse has been replaced, a bulb

may need replacement. (P. 375)

●If the replaced fuse blows again, have the vehicle inspected by your

Toyota dealer.

■If there is an overload in the circuits

The fuses are designed to blow, protecting the wiring harness from damage.

WARNING

■To prevent system breakdowns and vehicle fire

Observe the following precautions.

Failing to do so may cause damage to the vehicle, and possibly a fire or

injury.

●Never use a fuse of a higher amperage rating than indicated, or use any

other object in place of a fuse.

●Always use a genuine Toyota fuse or equivalent.

●Do not modify the fuse or the fuse box.

NOTICE

■Before replacing fuses

Have the cause of electrical overload determined and repaired by your

Toyota dealer.

374

4-3. Do-it-yourself maintenance

Light bulbs

You may replace the following bulbs by yourself. The difficulty level

of replacement varies depending on the bulb. If necessary bulb

replacement seems difficult to perform, contact your Toyota dealer.

■ Preparing a replacement light bulb

Check the wattage of the light bulb being replaced. (P. 469)

■ Front bulb locations

4

Front side marker lights

■ Rear bulb locations

License

plate

lights

Back-up lights

375

4-3. Do-it-yourself maintenance

Replacing light bulbs

■ Front side marker lights

Turn the steering wheel in the

opposite direction of the light to

be replaced.

STEP

1

2

3

Turn the steering wheel to a point

that allows your hand to easily fit

between the tire and fender liner.

Remove the clips and partly

remove the fender liner.

To prevent damage to the vehicle,

cover the tip of the screwdriver

with a rag.

Release the light's claw.

Insert the screwdriver into the

hole. While firmly pushing the

screwdriver forward, move it

towards the inside of the vehicle.

To prevent damage to the vehicle,

wrap the tip of the screwdriver

with a tape.

376

4-3. Do-it-yourself maintenance

Pull out the lamp and turn the

lens counterclockwise.

STEP

4

Remove the light bulb.

STEP

5

4

STEP

6

When installing, reverse the steps listed.

377

4-3. Do-it-yourself maintenance

■ Back-up lights

Remove the clips.

STEP

1

To prevent damage to the vehicle,

cover the tip of the screwdriver

with a rag.

Turn the bulb base counterclock-

wise.

STEP

2

Remove the light bulb.

STEP

3

STEP

4

When installing, reverse the steps listed.

378

4-3. Do-it-yourself maintenance

■ License plate lights

Turn the bulb base counterclock-

wise.

STEP

1

Remove the light bulb.

STEP

2

4

STEP

3

When installing, reverse the steps listed.

■ Replacing the following bulbs

If any of the lights listed below has burnt out, have it replaced by

your Toyota dealer.

● Headlights

● Parking lights/daytime running lights

● Front turn signal lights

● Front fog lights (if equipped)

● Stop/tail lights

● Stop lights

● Rear turn signal lights

● Rear side marker lights

● High mounted stoplight

379

4-3. Do-it-yourself maintenance

■Condensation build-up on the inside of the lens

Temporary condensation build-up on the inside of the light lens does not

indicate a malfunction. Contact your Toyota dealer for more information in

the following situations:

●Large drops of water are built up on the inside of the lens.

●Water has built up inside the light.

■LED light bulbs

The headlights, parking lights/daytime running lights, front turn signal lights,

front fog lights (if equipped), stop/tail lights, stop lights, rear turn signal lights,

rear side marker lights and high mounted stoplight consist of a number of

LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to

have the light replaced.

■When replacing light bulbs

Toyota recommends that you use genuine Toyota products designed for this

vehicle.

Because certain bulbs are connected to circuits designed to prevent over-

load, non-genuine parts or parts not designed for this vehicle may be unus-

able.

■Removing and installing the luggage trim cover clip

Removing

Installing

380

4-3. Do-it-yourself maintenance

WARNING

■Replacing light bulbs

●Turn off the lights. Do not attempt to replace the bulb immediately after

turning off the lights.

The bulbs become very hot and may cause burns.

●Do not touch the glass portion of the light bulb with bare hands. When it is

unavoidable to hold the glass portion, use and hold with a clean dry cloth

to avoid getting moisture and oils on the bulb.

Also, if the bulb is scratched or dropped, it may blow out or crack.

●Fully install the light bulbs and any parts used to secure them. Failure to

do so may result in heat damage, fire, or water entering a light unit. This

may damage the light or cause condensation to build up on the inner side

of the lens.

■When changing the back-up lights

Stop the engine and wait until the exhaust pipes have cooled down suffi-

ciently. The lights are located near the exhaust pipe and touching a hot

exhaust pipe can cause burns.

4

■To prevent damage or fire

Make sure bulbs are fully seated and locked.

381

4-3. Do-it-yourself maintenance

382

Maintenance and care for Your Toyota 86 2 Door First Generation (2012-2021)

Related Topics

Popular Owner Manuals

Latest Owner Manuals