For safety and security -> Child safety for Your Toyota 86 2 Door Second Generation (2022-2025)

1-2. Child safety  
56  
1-2.Child safety  
Riding with children  
Child restraint systems  
Observe the following precau-  
tions when children are in the  
vehicle.  
Use a child restraint system  
appropriate for the child, until  
the child becomes large  
enough to properly wear the  
vehicle’s seat belt.  
Before installing a child  
restraint system in the vehicle,  
there are precautions that need  
to be observed, different types  
of child restraint systems, as  
well as installation methods,  
etc., written in this manual.  
Use a child restraint system  
when riding with a small child  
that cannot properly use a seat  
belt. For the child’s safety,  
install the child restraint sys-  
tem to a rear seat. Be sure to  
follow the installation method  
that is in the operation manual  
enclosed with the restraint sys-  
tem.  
It is recommended that chil-  
dren sit in the rear seats to  
avoid accidental contact with  
the shift lever, wiper switch,  
etc.  
Use the window lock switch to  
avoid children operating the  
power window accidentally.  
(P.127)  
The use of a Toyota genuine  
child restraint system is rec-  
ommended, as it is safer to  
use in this vehicle. Toyota gen-  
uine child restraint systems  
are made specifically for  
Do not let small children oper-  
ate equipment which may  
catch or pinch body parts,  
such as the power window,  
hood, trunk, seats etc.  
Toyota vehicles. They can be  
purchased at a Toyota dealer.  
WARNING  
When children are in the vehicle  
Never leave children unattended in  
the vehicle, and never allow children  
to have or use the key.  
Table of contents  
Children may be able to start the vehi-  
cle or shift the vehicle into neutral.  
There is also a danger that children  
may injure themselves by playing with  
the windows or other features of the  
vehicle. In addition, heat build-up or  
extremely cold temperatures inside  
the vehicle can be fatal to children.  
Points to remember: P.57  
When using a child restraint sys-  
tem: P.64  
Child restraint system compatibility  
for each seating position: P.60  
Child restraint system installation  
method: P.64  
1-2. Child safety  
57  
ꢀ Fixed with a seat belt: P.65  
ꢀ Fixed with an ISOFIX lower  
anchorage: P.67  
ꢀ Using a top tether anchorage:  
P.68  
For effective protection in automo-  
bile accidents and sudden stops, a  
child must be properly restrained,  
using a seat belt or child restraint  
system which is correctly installed.  
For installation details, refer to the  
operation manual enclosed with the  
child restraint system. General  
installation instruction is provided in  
this manual.  
Points to remember  
1
Prioritize and observe the warn-  
ings, as well as the laws and reg-  
ulations for child restraint  
systems.  
Toyota strongly urges the use of a  
proper child restraint system that  
conforms to the weight and size of  
the child, installed on the rear seat.  
According to accident statistics, the  
child is safer when properly  
Use a child restraint system until  
the child becomes large enough  
to properly wear the vehicle’s  
seat belt.  
restrained in the rear seat than in  
the front seat.  
Holding a child in your or someone  
else’s arms is not a substitute for a  
child restraint system. In an acci-  
dent, the child can be crushed  
against the windshield or between  
the holder and the interior of the  
vehicle.  
Choose a child restraint system  
appropriate to the age and size  
of the child.  
Note that not all child restraint  
systems can fit in all vehicles.  
Before using or purchasing a  
child restraint system, check the  
compatibility of the child restraint  
system with seat positions.  
(P.60)  
Handling the child restraint sys-  
tem  
If the child restraint system is not  
properly fixed in place, the child or  
other passengers may be seriously  
injured or even killed in the event of  
sudden braking, sudden swerving, or  
an accident.  
If the vehicle were to receive a  
strong impact from an accident,  
etc., it is possible that the child  
restraint system has damage that is  
not readily visible. In such cases,  
do not reuse the restraint system.  
WARNING  
When a child is riding  
Observe the following precautions.  
Failure to do so may result in death or  
serious injury.  
1-2. Child safety  
WARNING  
58  
Never use a rear-facing child  
restraint system on the front pas-  
senger seat.  
The force of the rapid inflation of  
the front passenger airbag can  
cause death or serious injury to  
children in the event of an accident.  
Depending on the child restraint  
system, installation may be difficult  
or impossible. In those cases,  
check whether the child restraint  
system is suitable for installment in  
the vehicle. (P.60) Be sure to  
install and observe the usage rules  
after carefully reading the child  
restraint system fixing method in  
this manual, as well as the opera-  
tion manual enclosed with the child  
restraint system.  
Keep the child restraint system  
properly secured on the seat even if  
it is not in use. Do not store the  
child restraint system unsecured in  
the passenger compartment.  
There is a label(s) on the passen-  
ger side sun visor, indicating it is  
forbidden to attach a rear-facing  
child restraint system to the front  
passenger seat. However, as child  
restraint systems cannot be  
installed to the front passenger seat  
of this model, do not use a child  
restraint system on the front pas-  
senger seat regardless of the direc-  
tion it is facing.  
If it is necessary to detach the child  
restraint system, remove it from the  
vehicle or store it securely in the  
trunk.  
When using a child restraint  
system  
Details of the label(s) are shown in  
the illustration below.  
When installing a child  
restraint system to a front pas-  
senger seat  
Child restraint systems cannot be  
installed to the front passenger's  
seat.  
WARNING  
When installing a child restraint  
system  
Observe the following precautions.  
Failure to do so may result in death or  
serious injury.  
1-2. Child safety  
59  
WARNING  
1
When a junior seat is installed,  
always ensure that the shoulder  
belt is positioned across the center  
of the child’s shoulder. The belt  
should be kept away from the  
child’s neck, but not so that it could  
fall off the child’s shoulder.  
WARNING  
Do not allow the child to lean  
his/her head or any part of his/her  
body against the door or the area of  
the seat, front or rear pillars, or roof  
side rails from which the SRS side  
airbags or SRS curtain shield  
airbags deploy even if the child is  
seated in the child restraint system.  
It is dangerous if the SRS side  
airbags and curtain shield airbags  
inflate, and the impact could cause  
death or serious injury to the child.  
Use child restraint system suitable  
to the age and size of the child and  
install it to the rear seat.  
1-2. Child safety  
WARNING  
60  
of each seating position with child  
restraint systems].  
If the driver’s seat interferes with  
the child restraint system and pre-  
vents it from being attached cor-  
rectly, attach the child restraint  
system to the right-hand rear seat  
(left-hand drive vehicles) or the  
left-hand rear seat (right-hand drive  
vehicles). (P.63)  
Before confirming the compat-  
ibility of each seating position  
with child restraint systems  
1 Checking the child restraint sys-  
tem standards.  
Use a child restraint system that  
*1  
conforms to UN(ECE) R44 .  
The following approval mark is  
displayed on child restraint sys-  
tems which are conformed.  
Check for an approval mark  
attached to the child restraint  
system.  
Child restraint system com-  
patibility for each seating  
position  
Child restraint system compat-  
ibility for each seating posi-  
tion  
Compatibility of each seating posi-  
tion with child restraint systems  
(P.61) displays the type of child  
restraint systems that can be used  
and possible seating positions for  
installation using symbols. Also, the  
recommended child restraint sys-  
tem that is suitable for your child  
can be selected.  
Otherwise, check [Recommended  
child restraint systems and Com-  
patibility table] for recommended  
child restraint systems. (P.63)  
Check the selected child restraint  
system together with the following  
[Before confirming the compatibility  
Example of the displayed regulation  
Number  
*2  
UN(ECE) R44 approval mark  
A
The weight range of the child  
who is applicable for an  
UN(ECE) R44 approval mark is  
indicated.  
2 Checking the category of the  
child restraint system.  
Check the approval mark of the  
1-2. Child safety  
61  
child restraint system for which  
of the following categories the  
child restraint system is suitable.  
Also, if there are any uncertain-  
ties, check the user’s guide  
included with the child restraint  
system or contact the retailer of  
the child restraint system.  
ꢀ “universal”  
Right-hand drive vehicles  
1
ꢀ “semi-universal”  
ꢀ “restricted”  
ꢀ “vehicle specific”  
*
*
*1: UN(ECE) R44 is a U.N. regulations  
for child restraint systems.  
*2: The displayed mark may differ  
depending on the product.  
Suitable for “universal” category  
child restraint system fixed with  
the seat belt.  
Suitable for child restraint sys-  
tems given on recommended  
child restraint systems and  
compatibility table (P.63)  
Compatibility of each seating  
position with child restraint  
systems  
Suitable for ISOFIX child  
restraint system.  
Left-hand drive vehicles  
Includes a top tether anchorage  
point.  
Not suitable for child restraint  
system.  
Never use a rear-facing child  
restraint system on the front  
passenger seat.  
*: Not suitable for child restraint sys-  
tems with support leg.  
1-2. Child safety  
62  
Detail information for child restraint systems installation  
Seating position  
Seat position number  
Seating position suitable for universal  
belted (Yes/No)  
Yes  
No  
No  
Yes  
No  
No  
i-Size seating position (Yes/No)  
Seating position suitable for lateral fixture  
(L1/L2/No)  
Suitable rearward facing fixture  
(R1/R2X/R2/R3/No)  
R1*  
No  
Suitable forward facing fixture  
(F2X/F2/F3/No)  
F2X  
No  
F2X  
No  
Suitable junior seat fixture (B2/B3/No)  
*: Before installing a child restraint system to this seat, adjust the position of the  
front passenger's seat to 1st lock position.  
1st lock position  
A
ISOFIX child restraint systems are divided into different “fixture”. The child  
restraint system can be used in the seating positions for “fixture” mentioned  
in the table above. For kind of “fixture” relation, confirm the following table.  
If your child restraint system has no kind of “fixture” (or if you cannot find  
information in the table below), please refer to the child restraint system  
“vehicle list” for compatibility information or ask the retailer of your child  
seat.  
1-2. Child safety  
63  
Fixture  
F3  
Description  
Full-height, forward-facing child restraint systems  
Reduced-height forward-facing child restraint systems  
Reduced-height forward-facing child restraint systems  
Full-size, rearward-facing child restraint systems  
Reduced-size, rearward-facing child restraint systems  
Reduced-size, rearward-facing child restraint systems  
Rearward-facing infant seat  
F2  
F2X  
R3  
1
R2  
R2X  
R1  
L1  
Left lateral-facing (carrycot) infant seat  
Right lateral-facing (carrycot) infant seat  
Junior seat  
L2  
B2  
B3  
Junior seat  
Recommended child restraint systems and Compatibility table  
Seating position  
Recommended Child  
Mass groups  
Restraint System  
0,0+  
Up to 13kg (28 lb.)  
G0+, BABY SAFE  
PLUS (Yes/No)  
No  
Yes  
Yes  
I
DUO PLUS (Yes/No)  
Yes  
9 to 18kg (20 to 39 lb.)  
II, III  
KIDFIX 2S*1, 2 (Yes/No)  
15 to 36 kg (34 to 79  
lb.)  
Yes  
Yes  
*1: Adjust the restraint system headrest, so that it does not interfere with the vehicle  
interior.  
*2: Be sure to attach the seat belt through the SecureGuard.  
The child restraint systems mentioned in the table may not be available out-  
side the EU countries and United Kingdom.  
When securing some types of child  
restraint systems in rear seat, it  
may not be possible to properly use  
the seat belts in positions next to  
the child restraint without interfering  
with it or affecting seat belt effec-  
tiveness. Be sure your seat belt fits  
snugly across your shoulder and  
low on your hips. If it does not, or if  
it interferes with the child restraint,  
move to a different position. Failure  
to do so may result in death or seri-  
1-2. Child safety  
ous injury.  
64  
When installing a junior seat, if  
the child in your child restraint  
system is in a very upright posi-  
tion, adjust the seatback angle to  
the most comfortable position.  
And if the seat belt shoulder  
anchor is ahead of the child seat  
belt guide, move the seat cush-  
ion forward.  
When installing a child restraint  
in the rear seats, adjust the front  
seat so that it does not interfere  
with the child or child restraint  
system.  
When installing a child seat with  
support base, if the child seat  
interferes with the seatback  
when latching it into the support  
base, adjust the seatback rear-  
ward until there is no interfer-  
ence.  
When using the child restraint  
system with SecureGuard, be  
sure to guide the lap belt into  
SecureGuard  
illustration.  
as shown in the  
If the seat belt shoulder anchor is  
ahead of the child seat belt  
guide, move the seat cushion  
forward.  
Child restraint system installation method  
Confirm with the operation manual enclosed with the child restraint system  
about the installation of the child restraint system.  
1-2. Child safety  
Page  
65  
Installation method  
Seat belt attachment  
P.65  
P.67  
P.68  
1
ISOFIX lower anchorage  
attachment  
Top tether anchorage  
attachment  
is not within the “universal” cate-  
gory (or the necessary information  
is not in the table), refer to the  
“Vehicle List” provided by the child  
restraint system maker for various  
possible installation positions, or  
check the compatibility after asking  
the retailer of the child seat.  
(P.60, P.61)  
Child restraint system fixed  
with a seat belt  
Installing child restraint sys-  
tem using a seat belt  
Install the child restraint system in  
accordance to the operation man-  
ual enclosed with the child restraint  
system.  
If the child restraint system on hand  
1-2. Child safety  
66  
1 Run the seat belt through the  
child restraint system and insert  
the plate into the buckle. Make  
sure that the belt is not twisted.  
Securely fix the seat belt to the  
child restraint system in accord-  
ance to the directions enclosed  
with the child restraint system.  
and fully retract the seat belt.  
When releasing the buckle, the child  
restraint system may spring up due to  
the rebound of the seat cushion.  
Release the buckle while holding down  
the child restraint system.  
Since the seat belt automatically reels  
itself, slowly return it to the stowing  
position.  
When installing a child restraint  
system  
You may need a locking clip to install the  
child restraint system. Follow the  
instructions provided by the manufac-  
turer of the system. If your child restraint  
system does not provide a locking clip,  
you can purchase the following item  
from any authorized Toyota retailer or  
Toyota authorized repairer, or any relia-  
ble repairer: Locking clip for child  
restraint system  
2 If your child restraint system is  
not equipped with a lock-off (a  
seat belt locking feature),  
(Part No. 73119-22010)  
secure the child restraint system  
using a locking clip.  
WARNING  
When installing a child restraint  
system  
Observe the following precautions.  
Failure to do so may result in death or  
serious injury.  
Do not allow children to play with  
the seat belt. If the seat belt  
becomes twisted around a child’s  
neck, it may lead to choking or  
other serious injuries that could  
result in death. If this occurs and  
the buckle cannot be unfastened,  
scissors should be used to cut the  
belt.  
3 After installing the child restraint  
system, rock it back and forth to  
ensure that it is installed  
Ensure that the belt and plate are  
securely locked and the seat belt is  
not twisted.  
securely. (P.67)  
Removing a child restraint  
system installed with a seat  
belt  
Press the buckle release button  
1-2. Child safety  
67  
accordance to the operation man-  
ual enclosed with the child restraint  
system.  
WARNING  
Shake the child restraint system left  
and right, and forward and back-  
ward to ensure that it has been  
securely installed.  
If the child restraint system on hand  
is not within the “universal” cate-  
gory (or the necessary information  
is not in the table), refer to the  
“Vehicle List” provided by the child  
restraint system maker for various  
possible installation positions, or  
check the compatibility after asking  
the retailer of the child seat.  
(P.60)  
After securing a child restraint sys-  
tem, never adjust the seat.  
1
When a junior seat is installed,  
always ensure that the shoulder  
belt is positioned across the center  
of the child’s shoulder. The belt  
should be kept away from the  
child’s neck, but not so that it could  
fall off the child’s shoulder.  
Follow all installation instructions  
provided by the child restraint sys-  
tem manufacturer.  
1 Check the positions of the exclu-  
sive fixing bars, and install the  
child restraint system to the  
seat.  
Child restraint system fixed  
with an ISOFIX lower  
anchorage  
The bars are installed in the clearance.  
ISOFIX lower anchorages  
(ISOFIX child restraint system)  
Lower anchorages are provided for  
the each rear seats. (Buttons dis-  
playing the location of the anchor-  
ages are attached to the seats.)  
2 After installing the child restraint  
system, rock it back and forth to  
ensure that it is installed  
Installation with ISOFIX lower  
anchorage (ISOFIX child  
restraint system)  
securely. (P.67)  
Install the child restraint system in  
1-2. Child safety  
WARNING  
68  
accordance to the operation man-  
ual enclosed with the child restraint  
system.  
When installing a child restraint  
system  
Open the top tether anchorages  
cover, latch the hook onto the top  
tether anchorages and tighten the  
top strap.  
Observe the following precautions.  
Failure to do so may result in death or  
serious injury.  
After securing a child restraint sys-  
tem, never adjust the seat.  
Make sure the top strap is securely  
latched. (P.67)  
When using the lower anchorages,  
be sure that there are no foreign  
objects around the anchorages and  
that the seat belt is not caught  
behind the child restraint system.  
Follow all installation instructions  
provided by the child restraint sys-  
tem manufacturer.  
Using a top tether anchor-  
age  
Hook  
A
Top tether anchorages  
Top strap  
Top tether anchorages are provided  
for the each rear seat.  
When using a top tether anchorage  
Use top tether anchorages when  
fixing the top strap.  
Store the removed cover in a safe place.  
Also, after removing a child restraint  
system, make sure to install the  
removed cover to its original position.  
WARNING  
When installing a child restraint  
system  
Observe the following precautions.  
Failure to do so may result in death or  
serious injury.  
Firmly attach the top strap and  
make sure that the belt is not  
twisted.  
Top tether anchorages  
A
Top strap  
Do not attach the top strap to any-  
thing other than the top tether  
anchorage.  
Fixing the top strap to the top  
tether anchorages  
Install the child restraint system in  
1-2. Child safety  
69  
WARNING  
After securing a child restraint sys-  
tem, never adjust the seat.  
Follow all installation instructions  
provided by the child restraint sys-  
tem manufacturer.  
1