DIY - Electrical -> Replacing light bulbs for Your Toyota Aurion 4 Door First Generation (2006-2012)

DO-IT-YOURSELF MAINTENANCE -- ELECTRICAL COMPONENTS  
Adding washer fluid  
Replacing light bulbs—  
If any washer does not work, the washer  
fluid tank may be empty. Add washer fluid.  
Before replacing the headlight bulbs and  
front turn signal light bulbs, remove the  
engine compartment cover. See “Remov-  
ing the engine compartment cover” on  
page 251 in Section 7- 1.  
For the location of the washer fluid tank see  
“Engine compartment overview” on page 250  
in Section 7--1.  
The following illustrations show how to gain  
access to the bulbs. When replacing a bulb,  
make sure the ignition switch and light switch  
are off. Use bulbs with the wattage ratings  
given in the table.  
You may use plain water as washer fluid.  
However, in cold areas where temperatures  
range below the freezing point, use washer  
fluid containing antifreeze. This product is  
available at your Toyota dealer and most auto  
parts stores. Follow the manufacturer’s  
directions for how much to mix with water.  
The high mounted stoplight consists of a  
number of light emitting diodes (LEDs). If any  
of the LEDs burn out, take your vehicle to  
your Toyota dealer thave the light replaced.  
NOTICE  
Do not use engine antifreeze or any  
other substitute because it may damage  
your vehicle’s paint.  
CAUTION  
D To prevent burning yourself, do not  
reple the light bulbs while they are  
h.  
Halogen bulbs have pressurised gas  
inside and require special handling.  
They can burst or shatter if scratched  
or dropped. Hold a bulb only by its  
plastic or metal case. Do not touch the  
glass part of a bulb with bare hands.  
Vehicles with discharge headlights—  
D Do not touch the high-intensity dis-  
charge headlight’s high voltage  
socket when the headlights are turned  
on. An extremely high voltage of  
20000 V will be discharged and could  
result in serious injury or death by  
electric shock.  
D Do not attempt to take apart or repair  
the low beam headlight bulbs, con-  
nectors, power supply circuits, or re-  
lated components. Doing so could re-  
sult in electric shock and serious in-  
jury or death. Call your Toyota dealer  
for headlight repair or servicing, in-  
cluding replacement of bulbs and  
bulb disposal.  
274  
DO-IT-YOURSELF MAINTENANCE -- ELECTRICAL COMPONENTS  
—Headlights (low  
beam—halogen bulbs)  
NOTICE  
Only use a bulb of the listed type.  
The inside of exterior light lenses (e.g. head-  
lights) may temporarily fog up when the lens  
becomes wet. This is not a problem as the fog-  
ging is caused by a temperature difference be-  
tween the outside and inside of the lens, like  
the windshield fogs up in the rain. However, if  
there is a large drop of water on the inside of  
the lens, or if there is water pooled inside the  
light, contact your Toyota dealer.  
1. Turn the bulase counterclockwise to  
the front of the vehicle as shown.  
Light bulbs  
Headlights (low)  
W
Type  
Discharge bulbs  
Halogen bulbs  
35  
55  
A
B
Headlights (high)  
Front fog lights  
60  
55  
5
C
B
D
E
E
E
D
D
D
D
F
Parking lights  
Front turn signal lights  
Side turn signal lights  
Rear turn signal lights  
Back-up lights  
21  
5
21  
16  
5
Licence plate lights  
Front personal lights  
Rear personal lights  
Interior light  
2. Unplug the connector while depressing  
the lock release.  
5
8
If the connector is tight, wiggle it.  
8
Vanity lights  
8
D
D
D
D
Glove box light  
1.2  
3.8  
5
Boot light  
Door courtesy lights  
A: D4S discharge bulbs  
B: H11 halogen bulbs  
C: HB3 halogen bulbs  
D: Wedge base bulbs (clear)  
E: Wedge base bulbs (amber)  
F: Double end bulbs  
275  
DO-IT-YOURSELF MAINTENANCE -- ELECTRICAL COMPONENTS  
—Headlights (high beam)  
3. Install a new bulb and plug the connec-  
tor into the mounting hole. Install the  
back cover and turn it clockwise.  
1. Turn the back cver counterclockwise  
and remove it. Turn the bulb base coun-  
terclockwise to the front of the vehicle  
as shown.  
Aiming is not necessary after replacing the  
bulb. When aiming adjustment is necessary,  
contact your Toyota dealer.  
2. Unplug the connector while depressing  
the lock release.  
If the connector is tight, wiggle it.  
276  
DO-IT-YOURSELF MAINTENANCE -- ELECTRICAL COMPONENTS  
—Front turn signal lights  
3. Install a new bulb and plug the connec-  
tor into the mounting hole. Install the  
back cover and turn it clockwise.  
Aiming is not necessary after replacing the  
bulb. When aiming adjustment is necessary,  
contact your Toyota dealer.  
277  
DO-IT-YOURSELF MAINTENANCE -- ELECTRICAL COMPONENTS  
—Rear turn signal lights  
—Other exterior lights  
If any of the following lights burn out, con-  
tact your Toyota dealer:  
D front foglight,  
D parking light,  
D headlight (with discharge bulb),  
D side turn signal light,  
D back-up light,  
D licence plate light,  
D LED type high mounted stoplight, or  
D LED type tail or stop/tail light.  
NTICE  
Do not try to replace the front fog, park-  
ing, headlight (with discharge bulb),  
side turn signal, back-up or licence  
plate ht bulbs by yourself. You may  
damge the vehicle.  
278