Maintenance and care -> Maintenance and care for Your Toyota bZ4X SUV First Generation (2022-2024)

448  
7-1. Maintenance and care  
7-1.Maintenance and care  
scratch and outside temperature.  
The restoration time may become  
shorter when the coating is  
Cleaning and protect-  
ing the vehicle exte-  
rior  
warmed by applying warm water.  
Deep scratches caused by keys,  
coins, etc., cannot be restored.  
Perform the following to  
protect the vehicle and  
maintain it in prime condi-  
tion:  
Do not use wax that contain abra-  
sives.  
Automatic car washes  
Before washing the vehicle:  
• Fold the mirrors  
• Turn off the power back door (if  
equipped)  
Cleaning instructions  
Start washing from the front of the  
vehicle. Make sure to extend the  
mirrors before driving.  
Working from top to bottom,  
liberally apply water to the  
vehicle body, wheel wells and  
underside of the vehicle to  
remove any dirt and dust.  
Brushes used in automatic car  
washes may scratch the vehicle  
surface, parts (wheel, etc.) and  
harm your vehicle’s paint.  
Wash the vehicle body using  
a sponge or soft cloth, such  
as a chamois.  
Rear spoiler may not be washable  
in some automatic car washes.  
There may also be an increased  
risk of damage to vehicle.  
For hard-to-remove marks,  
use car wash soap and rinse  
thoroughly with water.  
When the shift position needs to  
be held in N, refer to P.239.  
High pressure car washes  
As water may enter the cabin, do  
not bring the nozzle tip near the  
gaps around the doors or perimeter  
of the windows, or spray these  
areas continuously.  
Wipe away any water.  
Wax the vehicle when the  
waterproof coating deterio-  
rates.  
Note for a smart key system  
If water does not bead on a clean  
surface, apply wax when the vehi-  
cle body is cool.  
If the door handle becomes wet  
while the electronic key is within  
the effective range, the door may  
lock and unlock repeatedly. In that  
case, follow the following correc-  
tion procedures to wash the vehi-  
cle:  
• Place the key in a position 6 ft. (2  
m) or more separate from the  
vehicle while the vehicle is being  
washed. (Take care to ensure that  
the key is not stolen.)  
Self-restoring coat  
The vehicle body has a self-restor-  
ing coating that is resistant to small  
surface scratches caused in a car  
wash, etc.  
The coating lasts for 5 to 8 years  
from when the vehicle is delivered  
from the plant.  
• Set the electronic key to battery-  
saving mode to disable the smart  
key system. (P.188)  
The restoration time differs  
depending on the depth of the  
Owner's Manual_USA_M42G23_en  
449  
7-1. Maintenance and care  
If the electronic key is inside the  
vehicle and a door handle  
approximately 5% solution of neu-  
tral detergent and water to clean  
the dirt off.  
becomes wet during a car wash, a  
buzzer may sound outside the  
vehicle and “Key Detected In  
Vehicle” may be shown on the  
multi-information display. To turn  
off the alarm, lock all the doors.  
Wipe the surface with a dry, soft  
cloth to remove any remaining  
moisture.  
To remove oily deposits, use alco-  
hol wet wipes or a similar product.  
Wheels and wheel ornaments  
Remove any dirt immediately by  
using a neutral detergent.  
WARNING  
When washing the vehicle  
Wash detergent off with water  
immediately after use.  
Do not apply water to the inside of  
the motor compartment. Doing so  
may cause the electrical compo-  
nents, etc. to catch fire.  
To protect the paint from damage,  
make sure to observe the follow-  
ing precautions.  
• Do not use acidic, alkaline or  
abrasive detergent  
• Do not use hard brushes  
• Do not use detergent on the  
wheels when they are hot, such  
as after driving or parking in hot  
weather  
When cleaning the windshield  
(vehicles with rain-sensing  
windshield wipers)  
Set the wiper switch to off.  
If the wiper switch is in “AUTO”,  
the wipers may operate unexpect-  
edly in the following situations,  
and may result in hands being  
caught or other serious injuries  
and cause damage to the wiper  
blades.  
Painted brake calipers (if  
equipped)  
When using detergent, use neu-  
tral detergent. Do not use hard  
brushes or abrasive cleaners, as  
they will damage the paint.  
Do not use detergent on the brake  
calipers when they are hot.  
7
Wash detergent off immediately  
after use.  
Brake pads and calipers  
Rust may form if the vehicle is  
parked with wet brake pads or disc  
rotors, causing them to stick. Before  
parking the vehicle after it is  
washed, drive slowly and apply the  
brakes several times to dry the  
parts.  
Off  
“AUTO”  
When the upper part of the  
windshield where the raindrop  
sensor is located is touched by  
hand  
Bumpers  
Do not scrub with abrasive cleaners.  
Plated portions  
When a wet rag or similar is  
held close to the raindrop sen-  
sor  
If dirt cannot be removed, clean the  
parts as follows:  
Use a soft cloth dampened with an  
Owner's Manual_USA_M42G23_en  
450  
7-1. Maintenance and care  
WARNING  
If the paint is chipped or  
scratched, have it repaired  
immediately.  
If something bumps against the  
windshield  
To prevent the wheels from cor-  
roding, remove any dirt and  
store in a place with low humid-  
ity when storing the wheels.  
If you directly touch the raindrop  
sensor body or if something  
bumps into the raindrop sensor  
Precaution regarding the rear  
Cleaning the exterior lights  
bumper  
Wash carefully. Do not use  
organic substances or scrub  
with a hard brush.  
This may damage the surfaces  
of the lights.  
If the paint of the rear bumper is  
chipped or scratched, the system  
may malfunction. If this occurs,  
consult your Toyota dealer.  
Toyota Safety Sense 3.0  
Do not apply wax to the sur-  
faces of the lights.  
BSM (if equipped)  
Wax may cause damage to the  
lenses.  
RCTA (if equipped)  
PKSB (if equipped)  
When using an automatic car  
wash (vehicles with rain-  
sensing windshield wipers)  
NOTICE  
Set the wiper switch to off posi-  
tion.  
If the wiper switch is in “AUTO”,  
the wipers may operate and the  
wiper blades may be damaged.  
To prevent paint deteriora-  
tion and corrosion on the  
body and components (alumi-  
num wheels, etc.)  
When using a high pressure  
car wash  
Wash the vehicle immediately in  
the following cases:  
When washing the vehicle, do  
not spray the camera or its sur-  
rounding area directly with a  
high pressure washer. Shock  
applied from high pressure  
water may cause the device to  
not operate normally.  
• After driving near the sea coast  
• After driving on salted roads  
• If coal tar or tree sap is present  
on the paint surface  
• If dead insects, insect droppings  
or bird droppings are present on  
the paint surface  
Do not spray water directly on  
the radar which is equipped  
behind the radar sensor cover.  
Otherwise it may cause the  
device to be damaged.  
• After driving in an area contami-  
nated with soot, oily smoke,  
mine dust, iron powder or chem-  
ical substances  
Do not bring the nozzle tip close  
to boots (rubber or resin manu-  
factured cover), or connectors  
or the following parts.  
• If the vehicle becomes heavily  
soiled with dust or mud  
The parts may be damaged if  
they come into contact with  
high-pressure water.  
• If liquids such as benzene and  
gasoline are spilled on the paint  
surface  
Owner's Manual_USA_M42G23_en  
451  
7-1. Maintenance and care  
Cleaning and protect-  
ing the vehicle interior  
NOTICE  
• Traction related parts  
• Steering parts  
• Suspension parts  
• Brake parts  
Perform cleaning in a man-  
ner appropriate to each  
component and its material.  
Keep the cleaning nozzle at  
least 11.9 in. (30 cm) away from  
the vehicle body. Otherwise  
resin section, such as moldings  
and bumpers, may be deformed  
and damaged. Also, do not con-  
tinuously hold the nozzle in the  
same place.  
Protecting the vehicle  
interior  
Remove dirt and dust using a  
vacuum cleaner. Wipe dirty  
surfaces with a cloth damp-  
ened with lukewarm water.  
Do not spray the lower part of  
the windshield continuously. If  
water enters the air conditioning  
system intake located near the  
lower part of the windshield, the  
air conditioning system may not  
operate correctly.  
If dirt cannot be removed,  
wipe it off with a soft cloth  
dampened with neutral deter-  
gent diluted to approximately  
1%.  
Do not wash the underside of  
the vehicle using a high pres-  
sure car washer. If water enters  
the traction battery, the EV sys-  
tem may malfunction.  
Wring out any excess water  
from the cloth and thoroughly  
wipe off remaining traces of  
detergent and water.  
Do not use the washer on the  
area around the charging port  
lid. Water could get into the  
charging inlet and could dam-  
age the vehicle.  
7
Shampooing the carpets  
There are several commercial foam-  
ing-type cleaners available. Use a  
sponge or brush to apply the foam.  
Rub in overlapping circles. Do not  
use water. Wipe dirty surfaces and  
let them dry. Excellent results are  
obtained by keeping the carpet as  
dry as possible.  
Cleaning aluminum parts  
When cleaning the hood, do not  
push hard or put weight on it.  
The aluminum part may be  
dented.  
Handling the seat belts  
Clean with mild soap and lukewarm  
water using a cloth or sponge. Also  
check the belts periodically for  
excessive wear, fraying or cuts.  
Front side windows with IR pro-  
tective coating  
The front side windows have IR pro-  
tective coating. To prevent any dam-  
Owner's Manual_USA_M42G23_en  
452  
7-1. Maintenance and care  
age to the IR protective coating,  
observe the following:  
NOTICE  
Cleaning detergents  
If the windows are dirty, gently  
wipe them with a cloth soaked in  
water or lukewarm water as soon  
as possible.  
Do not use the following types  
of detergent, as they may dis-  
color the vehicle interior or  
cause streaks or damage to  
painted surfaces:  
If the windows are very dirty, do  
not open and close them repeat-  
edly.  
• Non-seat portions: Organic sub-  
stances such as benzene or  
gasoline, alkaline or acidic solu-  
tions, dye, and bleach  
WARNING  
Water in the vehicle  
• Seats: Alkaline or acidic solu-  
tions, such as thinner, benzene,  
and alcohol  
Do not splash or spill liquid in  
the vehicle.  
Doing so may cause the electri-  
cal components, etc., to mal-  
function or catch fire.  
Do not use a polish wax or pol-  
ish cleaner. The instrument  
panel’s or other interior part’s  
painted surface may be dam-  
aged.  
Do not get any of the SRS com-  
ponents or wiring in the vehicle  
interior wet.  
(P.35)  
Water on the floor  
An electrical malfunction may  
cause the airbags to deploy or  
not function properly, resulting  
in death or serious injury.  
Do not wash the vehicle floor with  
water.  
Vehicle systems such as the  
audio system may be damaged if  
water comes into contact with  
electrical components such as the  
audio system above or under the  
floor of the vehicle. Water may  
also cause the body to rust.  
Vehicles with wireless charger:  
Do not let the wireless charger  
(P.430) get wet. Failure to do  
so may cause the charger to  
become hot and cause burns or  
could cause electric shock  
resulting in death or serious  
injury.  
When cleaning the inside of  
the windshield  
Do not allow glass cleaner to con-  
tact the lens. Also, do not touch  
the lens. (P.259)  
Cleaning the interior (espe-  
cially instrument panel)  
Do not use a polish wax or polish  
cleaner. The instrument panel  
may reflect off the windshield,  
obstructing the driver’s view and  
leading to an accident, resulting in  
death or serious injury.  
Cleaning the inside of the rear  
window  
Do not use a glass cleaner to  
clean the rear window, as this  
may cause damage to the rear  
window defogger heater wires.  
Use a cloth dampened with  
lukewarm water to gently wipe  
the window clean. Wipe the win-  
dow in strokes running parallel  
to the heater wires.  
Owner's Manual_USA_M42G23_en  
453  
7-1. Maintenance and care  
wipe off all remaining traces  
of detergent.  
NOTICE  
Be careful not to scratch or  
damage the heater wires.  
Wipe the surface with a dry,  
soft cloth to remove any  
remaining moisture. Allow the  
leather to dry in a shaded and  
ventilated area.  
Cleaning the front side win-  
dows  
Do not use any compound or  
abrasive product (e.g., glass  
cleaner, detergent, wax) to clean  
the windows. It may damage the  
coating.  
Caring for leather areas  
Toyota recommends cleaning the  
interior of the vehicle at least twice a  
year to maintain the quality of the  
vehicle’s interior.  
Cleaning the areas with  
satin-finish metal accents  
NOTICE  
Remove dirt using a water  
dampened soft cloth or syn-  
thetic chamois.  
Preventing damage to leather  
surfaces  
Observe the following precautions  
to avoid damage to and deteriora-  
tion of leather surfaces:  
Wipe the surface with a dry  
soft cloth to remove any  
remaining moisture.  
Remove any dust or dirt from  
leather surfaces immediately.  
Cleaning the areas with satin-  
finish metal accents  
Do not expose the vehicle to  
direct sunlight for extended peri-  
ods of time. Park the vehicle in  
the shade, especially during  
summer.  
The metal areas use a layer of real  
metal for the surface. It is necessary  
to clean them regularly. If dirty areas  
are left uncleaned for long periods  
of time, they may be difficult to  
clean.  
7
Do not place items made of  
vinyl, plastic, or containing wax  
on the upholstery, as they may  
stick to the leather surface if the  
vehicle interior heats up signifi-  
cantly.  
Cleaning the leather areas  
Remove dirt and dust using a  
vacuum cleaner.  
Cleaning the synthetic  
leather areas  
Wipe off any excess dirt and  
dust with a soft cloth damp-  
ened with diluted detergent.  
Remove dirt and dust using a  
vacuum cleaner.  
Use a diluted water solution of  
approximately 5% neutral wool  
detergent.  
Wipe it off with a soft cloth  
dampened with neutral deter-  
gent diluted to approximately  
1%.  
Wring out any excess water  
from the cloth and thoroughly  
Owner's Manual_USA_M42G23_en  
454  
7-1. Maintenance and care  
Wring out any excess water  
from the cloth and thoroughly  
wipe off remaining traces of  
detergent and water.  
Cleaning fabric portions  
To remove dust from the fab-  
ric, use a vacuum cleaner or  
adhesive tape.  
However, please remove the dust  
near the passenger airbag orna-  
ment by hand.  
Use a cloth dampened with  
water to gently wipe the fabric  
clean.  
Do not use detergents to clean  
the fabric.  
Vehicles with radiant heaters:  
Do not hard scrub on the fab-  
ric portion of the radiant heat-  
ers (P.413).  
Owner's Manual_USA_M42G23_en