Starting and Driving for Your Toyota Celica 2 Door Sixth Generation (1993-1999)

CELICA  
U
How to start the engine—  
(a) Before cranking  
1. Apply the parking brake firmly.  
Before starting the engine  
1. Check the area around the vehicle be-  
fore entering it.  
Part 3  
STARTING AND DRIV-  
ING  
2. Turn off unnecessary lights and acces-  
sories.  
2. Adjust seat position, seatback angle,  
head restraint height and steering  
wheel angle.  
3. Manual transmission: Press the clutch  
pedal to the floor and shift the trans-  
mission into neutral. Hold the clutch  
pedal to the floor until the engine is  
started. A starter safety device will pre-  
vent the starter from operating if the  
clutch pedal is not fully depressed.  
D Before starting the engine  
D How to start the engine  
3. Adjust inside and outside rear view  
mirrors.  
4. Lock both side doors.  
5. Fasten seat belts.  
D Tips for driving in various  
conditions  
Automatic transmission: Put the se-  
lector lever in ”P”. If you need to re-  
start the engine while the vehicle is  
moving, put the selector lever in ”N”.  
A starter safety device will prevent the  
starter from operating if the selector  
lever is in any drive position.  
D Winter driving tips  
D Trailer towing  
D How to save fuel and make your  
vehicle last longer, too  
4. Automatic transmission only: De-  
press the brake pedal and hold it to  
the floor until driving off.  
123  
CELICA  
U
Tips for driving in various  
conditions  
(b) Starting the engine  
Before starting the engine, be sure to  
follow the instructions in ”(a) Before  
cranking”.  
D Always slow down in gusty crosswinds.  
NOTICE  
This will allow you much better control.  
z Do not crank for more than 30 sec-  
onds at a time. This may overheat  
the starter and wiring systems.  
D Drive slowly onto curbs and, if pos-  
sible, at a right angle. Avoid driving  
onto high, sharpedged objects and  
other road hazards. Failure to do so  
can lead to severe tire damage result-  
ing in tire bursts.  
Normal starting procedure  
The multiport fuel injection system/sequen-  
tial multiport fuel injection system in your  
engine automatically controls the proper  
airfuel mixture for starting. You can start  
a cold or hot engine as follows:  
z Do not race a cold engine.  
z If the engine becomes difficult to  
start or stalls frequently, have the  
engine checked immediately.  
D When parking on a hill, turn the front  
wheels until they touch the curb so  
that the vehicle will not roll. Apply the  
parking brake, and place the transmis-  
sion in ”P” (automatic) or in first or  
reverse (manual). If necessary, block  
the wheels.  
1. With your foot off the accelerator ped-  
al, crank the engine by turning the key  
to ”START”. Release it when the en-  
gine starts.  
2. After the engine runs for about 10 sec-  
onds, you are ready to drive.  
D Washing your vehicle or driving through  
deep water may get the brakes wet. To  
see whether they are wet, check that  
there is no traffic near you, and then  
press the pedal lightly. If you do not  
feel a normal braking force, the brakes  
are probably wet. To dry them, drive  
the vehicle cautiously while lightly  
pressing the brake pedal with the park-  
ing brake pulled. If they still do not  
work safely, pull to the side of the road  
and call a Toyota dealer for assistance.  
If the weather is below freezing, let the  
engine warm up for a few minutes before  
driving.  
If the engine stalls...  
Simply restart it, using the correct proce-  
dure given in normal starting.  
If the engine will not start—  
See ”If your vehicle will not start” in Part  
4.  
124  
CELICA  
U
Winter driving tips  
Make sure you have ethyleneglycol an-  
tifreeze in the radiator.  
D Do not drive in excess of the speed  
limit. Even if the legal speed limit  
permits it, do not drive over 140  
km/h (85 mph) unless your vehicle  
has highspeed capability tires.  
Driving over 140 km/h (85 mph) may  
result in tire failure, loss of control  
and possible injury. Be sure to con-  
CAUTION  
D Before driving off, make sure that  
the parking brake is fully released  
and the parking brake reminder  
light is off.  
NOTICE  
Do not use alcohol type antifreeze.  
Check the condition of the battery and  
cables.  
D Do not leave your vehicle unat-  
tended while the engine is running.  
sult  
a
tire dealer to determine  
Cold temperatures reduce the capacity of  
any battery, so it must be in top shape  
to provide enough power for winter start-  
ing. Chapter 73 tells you how to visually  
inspect the battery. Your Toyota dealer  
and most service stations will be pleased  
to check the level of charge.  
D Do not rest your foot on the brake  
pedal while driving. It can cause  
dangerous overheating, needless  
wear, and poor fuel economy.  
whether the tires on your vehicle  
are highspeed capability tires or  
not before driving at such speeds.  
D Do not continue normal driving  
when the brakes are wet. If they are  
wet, your vehicle will require a lon-  
ger stopping distance, and it may  
pull to one side when the brakes  
are applied. Also, the parking brake  
will not hold the vehicle securely.  
D To drive down a long or steep hill,  
reduce your speed and downshift.  
Remember, if you ride the brakes  
excessively, they may overheat and  
not work properly.  
Make sure the engine oil viscosity is  
suitable for the cold weather.  
See Chapter 72 for recommended viscos-  
ity. Leaving a heavy summer oil in your  
vehicle during winter months may cause  
harder starting. If you are not sure about  
which oil to use, call your Toyota deal-  
er—he will be pleased to help.  
D Be careful when accelerating, up-  
shifting, downshifting or braking on  
a slippery surface. Sudden accelera-  
tion or engine braking, could cause  
the vehicle to spin or skid.  
Keep the door locks from freezing.  
Squirt lock deicer or glycerine into the  
locks to keep them from freezing. To open  
a frozen lock, try heating the key before  
inserting it.  
125  
CELICA  
U
Trailer towing  
Your vehicle is designed primarily as a  
Use a washer fluid containing an anti-  
freeze solution.  
Depending on where you are driving,  
we recommend you carry some emer-  
gency equipment.  
passengercarrying vehicle. Towing  
a
trailer will have an adverse effect on  
handling, performance, braking, durability  
and driving economy (fuel consumption,  
etc.). Your safety and satisfaction depend  
on the proper use of correct equipment  
and cautious driving habits. For your  
safety and the safety of others, you must  
not overload your vehicle or trailer. Toyota  
warranties do not apply to damage or  
malfunction caused by towing a trailer for  
commercial purposes. Ask your local  
Toyota dealer for further details before  
towing.  
This product is available at your Toyota  
dealer and most auto parts stores. Follow  
the manufacturer’s directions for how  
much to mix with water.  
Some of the things you might put in the  
vehicle are tire chains, window scraper,  
bag of sand or salt, flares, small shovel,  
jumper cables, etc.  
NOTICE  
Do not use engine antifreeze or any  
other substitute because it may dam-  
age your vehicle’s paint.  
Do not use your parking brake when  
there is a possibility it could freeze.  
WEIGHT LIMITS  
When parking, put the transmission into  
”P” (automatic) or into first or reverse  
(manual) and block the rear wheels. Do  
not use the parking brake, or snow or  
water accumulated in and around the  
parking brake mechanism may freeze,  
making it hard to release.  
Before towing, make sure the total trailer  
weight, gross vehicle weight, gross axle  
weight and trailer tongue load are all with-  
in the limits.  
The total trailer weight and tongue load  
can be measured with platform scales  
found at a highway weighing station, build-  
ing supply company, trucking company,  
junk yard, etc.  
Keep ice and snow from accumulating  
under the fenders.  
Ice and snow built up under your fenders  
can make steering difficult. During bad  
winter driving, stop and check under the  
fenders occasionally.  
126  
CELICA  
U
D The trailer cargo load should be  
distributed so that the tongue load  
is 9 to 11 % of the total trailer  
weight, not exceeding the maximum  
of 90 kg (200 lb.). Never load the  
trailer with more weight in the back  
than in the front. About 60 % of the  
trailer load should be in the front  
half of the trailer and the remaining  
40 % in the rear.  
Total trailer weight  
Tongue load  
Tongue load  
100=9 to 11%  
Total trailer weight  
HITCHES  
D Use only  
a
hitch which is recom-  
mended by the hitch manufacturer and  
conforms to the total trailer weight re-  
quirement.  
D The gross vehicle weight must not  
exceed the Gross Vehicle Weight  
Rating (GVWR) indicated on the  
Certification Label. The gross ve-  
hicle weight is the sum of weights  
of the unloaded vehicle, driver, pas-  
sengers, luggage, hitch and trailer  
tongue load. It also includes the  
weight of any special equipment  
installed on your vehicle.  
CAUTION  
D The total trailer weight (trailer  
weight plus its cargo load) must  
not exceed 907 kg (2000 lb.). Ex-  
ceeding this weight is dangerous.  
D Follow the directions supplied by the  
hitch manufacturer, and bolt the hitch  
securely to the rear bumper. Lubricate  
the hitch ball with  
grease.  
a
light coat of  
D The load on either the front or rear  
axle resulting from distribution of  
the gross vehicle weight on both  
axles must not exceed the Gross  
Axle Weight Rating (GAWR) listed  
on the Certification Label.  
127  
CELICA  
U
D Toyota recommends removing the trail-  
D A safety chain must always be used  
between the towing vehicle and the  
trailer. Leave sufficient slack in the  
chain for turns. The chain should  
cross under the trailer tongue to  
prevent the tongue from dropping to  
the ground in case it becomes dam-  
aged or separated. For correct safety  
chain procedures, follow the hitch or  
trailer manufacturer’s recommenda-  
tions.  
TIRES  
er hitch whenever you are not towing  
D Ensure that your vehicle’s tires are  
properly inflated. See Chapter 72 for  
instructions.  
a
trailer to reduce the possibility of  
additional damage caused by the hitch  
if your vehicle is struck from behind.  
After removing the hitch, seal any  
mounting holes in the vehicle body to  
prevent entry of pollutants such as ex-  
haust fumes, dirt, water, etc.  
D The trailer tires should be inflated to  
the pressure recommended by the trail-  
er manufacturer in respect to the total  
trailer weight.  
TRAILER LIGHTS  
NOTICE  
D Trailer lights must comply with federal,  
state/provincial and local regulations.  
See your local recreational vehicle  
dealer or rental agency for the correct  
type of wiring and relays for your trail-  
er. Check for correct operation of the  
turn signals and stop lights each time  
you hitch up. Direct splicing may dam-  
age your vehicle’s electrical system  
and cause a malfunction of your lights.  
Do not use axlemounted hitches as  
they can cause damage to the axle  
housing, wheel bearings, wheels or  
tires. Also, never install a hitch which  
may interfere with the normal function  
of an Energy Absorbing Bumper.  
CAUTION  
D If the total trailer weight exceeds  
453 kg (1000 lb.), trailer brakes are  
required.  
D Never tap into your vehicle’s hy-  
draulic system as it would lower its  
braking effectiveness.  
BRAKES AND SAFETY CHAINS  
D Toyota recommends trailers with  
brakes that conform to any applica-  
ble federal and state/provincial regu-  
lations.  
BREAKIN SCHEDULE  
D Never tow a trailer without using a  
safety chain securely attached to  
both the trailer and the vehicle. If  
damage occurs to the coupling unit  
or hitch ball, there is danger of the  
trailer wandering over into another  
lane.  
D Toyota recommends that you do not  
tow a trailer with a new vehicle or a  
vehicle with any new power train com-  
ponent (engine, transmission, differen-  
tial, wheel bearing, etc.) for the first  
800 km (500 miles) of driving.  
128  
CELICA  
U
MAINTENANCE  
TRAILER TOWING TIPS  
D Because stopping distance may be in-  
creased, vehicletovehicle distance  
D If you tow a trailer, your vehicle will  
require more frequent maintenance due  
to the additional load. For this informa-  
tion, please refer to the scheduled  
maintenance information in the ”Own-  
er’s Manual Supplement/Maintenance  
Schedule”.  
When towing a trailer, your vehicle will  
handle differently than when not tow-  
ing. The three main causes of vehicle−  
trailer accidents are driver error, exces-  
sive speed and improper trailer loading.  
Keep these in mind when towing:  
should be increased when towing  
a
trailer. For each 16 km/h (10 mph) of  
speed, allow at least one vehicle and  
trailer length between you and the ve-  
hicle ahead. Avoid sudden braking as  
you may skid, resulting in jackknifing  
and loss of control. This is especially  
true on wet or slippery surfaces.  
D Before starting out, check operation of  
the lights and all vehicletrailer connec-  
D Retighten all fixing bolts of the towing  
ball and bracket after approximately  
1000 km (600 miles) of trailer driving.  
tions. After driving  
a
short distance,  
D Avoid jerky starts or sudden accelera-  
stop and recheck the lights and con-  
nections. Before actually towing a trail-  
er, practice turning, stopping and back-  
ing with a trailer in an area away from  
traffic until you learn the feel.  
tion. If your vehicle has  
a
manual  
PRETOWING SAFETY CHECK  
transmission, prevent excessive clutch  
slippage by keeping engine rpm low  
and not racing the engine. Always start  
out in first gear.  
D Check that your vehicle remains a lev-  
el when a loaded or unloaded trailer is  
hitched. Do not drive if the vehicle has  
an abnormal noseup or nosedown  
condition, and check for improper  
tongue load, overload, worn suspension  
or other possible causes.  
D Backing with a trailer is difficult and  
requires practice. Grip the bottom of  
the steering wheel and move your hand  
to the left to move the trailer to the  
left. Move your hand to the right to  
move the trailer to the right. (This pro-  
cedure is generally opposite to that  
when backing without a trailer). Also,  
just turn the steering wheel a little at  
D Avoid jerky steering and sharp turns.  
The trailer could hit your vehicle in a  
tight turn. Slow down before making a  
turn to avoid the necessity of sudden  
braking.  
D Make sure the trailer cargo is securely  
loaded so that it can not shift.  
D Remember that when making a turn,  
the trailer wheels will be closer than  
the vehicle wheels to the inside of the  
turn. Therefore, compensate for this by  
D Check that your rear view mirrors con-  
form to any applicable federal, state/  
provincial or local regulation. If not,  
install the rear view mirrors required  
for towing purpose.  
a
time, avoiding sharp or prolonged  
turning. Have someone guide you when  
backing to reduce the risk of an acci-  
dent.  
making  
a
larger than normal turning  
radius with your vehicle.  
129  
CELICA  
U
D Crosswinds and rough roads will ad-  
versely affect handling of your vehicle  
and trailer, causing sway. Pay attention  
to the rear from time to time to pre-  
pare yourself for being passed by large  
trucks or buses, which may cause your  
vehicle and trailer to sway. If swaying  
happens, firmly grip the steering wheel  
and reduce speed immediately but  
gradually. Never increase speed. Steer  
straight ahead. If you make no extreme  
correction with the steering or brakes,  
the vehicle and trailer will stabilize.  
D Because of the added load of the trail-  
er, your vehicle’s engine may overheat  
on hot days (at temperatures over  
30_C [85_F]) when going up a long or  
steep grade with a trailer. If the engine  
coolant temperature gauge indicates  
overheating, immediately turn off the air  
conditioning (if in use), pull off the road  
and stop in a safe spot. Refer to ”If  
your vehicle overheats” in Part 4 of  
this manual.  
1. With the transmission in ”P” position  
(automatic) or the clutch pedal de-  
pressed (manual), start the engine.  
(With an automatic transmission, be  
sure to keep the brake pedal de-  
pressed.)  
2. Shift into gear.  
3. Release the parking brake (also foot  
brake on automatic transmission ve-  
hicles) and slowly pull or back away  
from the wheel blocks. Stop and apply  
your brakes.  
D Always place wheel blocks under both  
the vehicle and trailer wheels when  
parking. Apply the parking brake firmly.  
Put the transmission in ”P” (automatic)  
or in first or reverse (manual). Avoid  
parking on a slope with a trailer, but  
if it cannot be avoided, do so only  
after performing the following:  
D Be careful when passing other ve-  
hicles. Passing requires considerable  
distance. After passing a vehicle, do  
not forget the length of your trailer and  
be sure you have plenty of room be-  
fore changing lanes.  
4. Have someone retrieve the blocks.  
CAUTION  
D Do not exceed 72 km/h (45 mph) or  
the posted towing speed limit,  
whichever is lower. Because insta-  
bility (swaying) of a towing vehicle−  
D In order to maintain engine braking effi-  
ciency do not use fifth gear (manual  
transmission) or overdrive (automatic  
transmission).  
1. Apply the brakes and hold.  
2. Have someone place wheel blocks un-  
der both the vehicle and trailer wheels.  
trailer  
combination  
usually  
in-  
creases as the speed increases, ex-  
ceeding 72 km/h (45 mph) may  
cause loss of control.  
3. When the wheel blocks are in place,  
release your brakes slowly until the  
blocks absorb the load.  
D Slow down and downshift before  
descending steep or long downhill  
grades. Do not make sudden down-  
shifts.  
4. Apply the parking brake firmly.  
5. Shift into first or reverse (manual) or  
”P” (automatic) and turn off the engine.  
When restarting out after parking on a  
slope:  
130  
CELICA  
U
How to save fuel and make  
your vehicle last longer, too  
Getting more kilometers/mileage from  
a
D Avoid continuous speeding up and  
slowing down. Stopandgo driving  
wastes fuel.  
D Avoid holding the brake pedal down  
too long or too frequently. This  
could cause the brakes to overheat  
and result in reduced braking effi-  
ciency.  
liter/gallon of fuel is easy—just take it  
easy. It will help make your vehicle last  
longer, too. Here are some specific tips  
on how to save money on both fuel and  
repairs:  
D Avoid unnecessary stopping and  
braking. Maintain a steady pace. Try  
to time the traffic signals so you only  
need to stop as little as possible or  
take advantage of through streets to  
avoid traffic lights. Keep a proper dis-  
tance from other vehicles to avoid sud-  
den braking. This will also reduce wear  
on your brakes.  
D Keep your tires inflated at the cor-  
rect pressure. Underinflation causes  
tire wear and wastes fuel. See Chapter  
72 for instructions.  
D Do not carry unneeded weight in  
your vehicle. Excess weight puts  
a
heavier load on the engine, causing  
greater fuel consumption.  
D Avoid heavy traffic or traffic jams  
whenever possible.  
D Avoid lengthy warmup idling. Once  
the engine is running smoothly, begin  
driving—but gently. Remember, howev-  
er, that on cold winter days this may  
take a little longer.  
D Do not rest your foot on the clutch  
or brake pedal. This causes needless  
wear, overheating and poor fuel econo-  
my.  
D Maintain a moderate speed on high-  
ways. The faster you drive, the greater  
the fuel consumption. By reducing your  
speed, you will cut down on fuel con-  
sumption.  
D Accelerate slowly and smoothly.  
Avoid jackrabbit starts. Get into high  
gear as quickly as possible.  
D Avoid long engine idling. If you have  
a long wait and you are not in traffic,  
it is better to turn off the engine and  
start again later.  
D Keep the front wheels in proper  
alignment. Avoid hitting the curb and  
slow down on rough roads. Improper  
alignment not only causes faster tire  
wear but also puts an extra load on  
the engine, which, in turn, wastes fuel.  
D Avoid engine lug or overrevving. Use  
a gear position suitable for the road on  
which you are travelling.  
131  
CELICA  
U
D Keep the bottom of your vehicle free  
from mud, etc. This not only lessens  
weight but also helps prevent corro-  
sion.  
D Keep your vehicle tunedup and in  
top shape.  
A
dirty air cleaner,  
improper valve clearance, dirty plugs,  
dirty oil and grease, brakes not  
adjusted, etc. all lower engine perfor-  
mance and contribute to poor fuel  
economy. For longer life of all parts  
and lower operating costs, keep all  
maintenance work on schedule, and if  
you often drive under severe condi-  
tions, see that your vehicle receives  
more frequent maintenance (For sched-  
uled maintenance information, please  
refer to the separate ”Owner’s Manual  
Supplement/Maintenance Schedule”).  
CAUTION  
Never turn off the engine to coast  
down hills. Your power steering and  
brake booster will not function with-  
out the engine running. Also, the  
emission control system operates  
properly only when the engine is run-  
ning.  
132