Get In case of an emergency Guide for Toyota Corolla 4 Door Eighth Generation (2000-2006)

’04 Corolla_U (L/O 0306)

SECTION

IN CASE OF AN EMERGENCY

4

In case of an emergency

If your vehicle will not start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

If your engine stalls while driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

If your vehicle overheats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

If you have a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

If your vehicle becomes stuck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195

If your vehicle needs to be towed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196

If you cannot shift automatic transmission selector lever . . . . . . . . 199

If you lose your keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199

If you lose your wireless remote control transmitter . . . . . . . . . . . . . 200

181

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

If your vehicle will not start—

(a) Simple checks

(b) Starting a flooded engine

Before making these checks, make sure

you have followed the correct starting pro-

cedure given in “How to start the engine”

on page 170 in Section 3 and that you

have sufficient fuel.

If the engine turns over at its normal

speed but will not start—

If the engine will not start, your engine

may be flooded because of repeated

cranking.

1. Turn the ignition key to “ACC” or

“LOCK” and try starting the engine

again.

If this happens, turn the key to “START”

with the accelerator pedal fully depressed.

Keep the key and accelerator pedal in

these positions for 15 seconds and re-

lease them. Then try starting the engine

with your foot off the accelerator pedal.

If the engine is not turning over or is

turning over too slowly—

2. If the engine will not start, the engine

may be flooded because of repeated

cranking. See “(b) Starting a flooded

engine” on page 182 for further instruc-

tions.

1. Check that the battery terminals are

tight and clean.

If the engine does not start after 15 sec-

onds of cranking, release the key, wait a

few minutes and try again.

2. If the battery terminals are O.K., switch

on the interior light.

3. If the engine still will not start, it needs

adjustment or repair. Call

a

Toyota

3. If the light is out, dim or goes out

when the starter is cranked, the battery

is discharged. You may try jump start-

ing. See “(c) Jump starting” on page

183 for further instructions.

dealer or qualified repair shop.

If the engine still will not start, it needs

adjustment or repair. Call a Toyota dealer

or qualified repair shop for assistance.

NOTICE

If the light is O.K., but the engine still will

not start, it needs adjustment or repair.

Do not crank for more than 30 se-

conds at a time. This may overheat

the starter and wiring systems.

Call

a

Toyota dealer or qualified repair

shop.

NOTICE

Do not pull− or push−start the ve-

hicle. It may damage the vehicle or

cause

a

collision when the engine

starts. Also the three−way catalytic

converter may overheat and become a

fire hazard.

182

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

(c) Jump starting

To avoid serious personal injury and

damage to your vehicle which might re-

sult from battery explosion, acid burns,

electrical burns, or damaged electronic

components, these instructions must be

followed precisely.

JUMP STARTING PROCEDURE

D The gas normally produced by

a

1. If the booster battery is installed in

another vehicle, make sure the vehicles

are not touching. Turn off all unneces-

sary lights and accessories.

battery will explode if a flame or

spark is brought near. Use only

standardized jumper cables and do

not smoke or light a match while

jump starting.

2. If required, remove all the vent plugs

from the booster and discharged batter-

ies. Lay a cloth over the open vents

on the batteries. (This helps reduce the

explosion hazard, personal injuries and

burns.)

If you are unsure about how to follow this

procedure, we strongly recommend that

you seek the help of a competent me-

chanic or towing service.

NOTICE

The battery used for boosting must

be 12 V. Do not jump start unless you

are sure that the booster battery is

correct.

CAUTION

3. If the engine in the vehicle with the

booster battery is not running, start it

and let it run for a few minutes. During

jump starting, run the engine at about

2000 rpm with the accelerator pedal

lightly depressed.

D Batteries

contain

sulfuric

acid

which is poisonous and corrosive.

Wear protective safety glasses when

jump starting, and avoid spilling

acid on your skin, clothing, or ve-

hicle.

D If you should accidentally get acid

on yourself or in your eyes, remove

any contaminated clothing and flush

the affected area with water imme-

diately. Then get immediate medical

attention. If possible, continue to

apply water with a sponge or cloth

while en route to the medical office.

183

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

Positive terminal (“+” mark)

Discharged battery

Discharged

battery

Jumper

cable

Positive

terminal

(“+” mark)

Booster

battery

Jumper cable

Negative terminal

(“−” mark)

Booster battery

Connecting point

4. Make the cable connections in the or-

der a, b, c, d.

c. Connect the clamp of the negative

(black) jumper cable to the negative (−)

terminal on the booster battery.

Do not connect the cable to or near any

part that moves when the engine is

cranked.

a. Connect the clamp of the positive

(red) jumper cable to the positive (+)

terminal on the discharged battery.

d. Connect the clamp at the other end

of the negative (black) jumper cable to

a solid, stationary, unpainted, metallic

point of the vehicle with the discharged

battery.

b. Connect the clamp at the other end

of the positive (red) jumper cable to

the positive (+) terminal on the booster

battery.

CAUTION

When making the connections, to

avoid serious injury, do not lean over

the battery or accidentally let the

jumper cables or clamps touch any-

thing except the correct battery termi-

nals or the ground.

The recommended connecting point is

shown in the following illustration:

184

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

If your engine stalls while

driving

If your vehicle overheats

5. Start your engine in the normal way.

After starting, run it at about 2000 rpm

for several minutes with the accelerator

pedal lightly depressed.

If your engine stalls while driving...

If your engine coolant temperature

gauge indicates overheating, if you ex-

perience a loss of power, or if you hear

a loud knocking or pinging noise, the

engine has probably overheated. You

should follow this procedure...

1. Reduce your speed gradually, keeping

a straight line. Move cautiously off the

road to a safe place.

6. Carefully disconnect the cables in the

exact reverse order: the negative cable

and then the positive cable.

2. Turn on your emergency flashers.

3. Turn the ignition key to “ACC” or

“LOCK”, and try starting the engine

again.

1. Pull safely off the road, stop the ve-

hicle and turn on your emergency

flashers. Put the transmission in “P”

(automatic) or neutral (manual) and ap-

ply the parking brake. Turn off the air

conditioning if it is being used.

7. Carefully dispose of the battery cover

cloths—they may now contain sulfuric

acid.

If the engine will not start, see “If your

vehicle will not start” on page 182 in this

Section.

8. If removed, replace all the battery vent

plugs.

2. If coolant or steam is boiling out of the

radiator or reservoir, stop the engine.

Wait until the steam subsides before

opening the hood. If there is no coolant

boiling over or steam, leave the engine

running and make sure the electric

cooling fan is operating. If it is not,

turn the ignition off.

If the cause of your battery discharging is

not apparent (for example, lights left on),

you should have it checked at your Toyota

dealer.

CAUTION

If the engine is not running, the pow-

er assist for the brakes and steering

will not work so steering and braking

will be much harder than usual.

CAUTION

To help avoid personal injury, keep

the hood closed until there is no

steam. Escaping steam or coolant is

a sign of very high pressure.

185

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

If you have a flat tire—

3. Look for obvious coolant leaks from the

radiator, hoses, and under the vehicle.

However, note that water draining from

the air conditioning is normal if it has

been used.

6. After the engine coolant temperature

has cooled to normal, again check the

coolant level in the reservoir. If neces-

sary, bring it up to half full again. Seri-

ous coolant loss indicates a leak in the

system. You should have it checked as

soon as possible at your Toyota dealer.

1. Reduce your speed gradually

while driving in a straight line.

Move cautiously off the road to a

safe place well away from the traf-

fic. Avoid stopping on the center

divider of a highway. Park on a lev-

el spot with firm ground.

CAUTION

2. Stop the engine and turn on your

emergency flashers.

3. Firmly set the parking brake and

put the transmission in “P” (auto-

matic) or reverse (manual).

4. Have everyone get out of the ve-

hicle on the side away from traffic.

5. Read the following instructions

thoroughly.

When the engine is running, keep

hands and clothing away from the

moving fan and engine drive belts.

4. If the coolant is leaking, stop the en-

gine immediately. Call a Toyota dealer

for assistance.

5. If there are no obvious leaks, check

the coolant reservoir. If it is dry, add

coolant to the reservoir while the en-

gine is running. Fill it about half full.

CAUTION

When jacking, be sure to observe

the following to reduce the possi-

bility of personal injury:

Do not attempt to remove the radiator

cap when the engine and radiator are

hot. Serious injury could result from

scalding hot fluid and steam blown

out under pressure.

D Follow jacking instructions.

186

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

D Do not put any part of your

body under the vehicle sup-

ported by the jack. Otherwise,

personal injury may occur.

D Use the jack only for lifting

your vehicle during wheel

changing.

D Do not raise the vehicle with

D Do not start or run the engine

while your vehicle is supported

by the jack.

someone in the vehicle.

D When raising the vehicle, do

not place any objects on top

of or underneath the jack.

D Stop the vehicle on a level firm

ground, firmly set the parking

brake and put the transmission

in “P” (automatic) or reverse

(manual). Block the wheel diag-

onally opposite to the one be-

ing changed if necessary.

D Raise the vehicle only high

enough to remove and change

the tire.

Compact spare tire

The compact spare tire is designed

for temporary emergency use only.

NOTICE

D Make sure to set the jack prop-

erly in the jack point. Raising

the vehicle with jack improper-

ly positioned will damage the

vehicle or may allow the ve-

hicle to fall off the jack and

cause personal injury.

Do not continue driving with a

deflated tire. Driving even a

short distance can damage a

tire and wheel beyond repair.

The compact spare tire is identified

by

the

distinctive

wording

“TEMPORARY USE ONLY” molded

into the side wall of the tire.

The compact spare tire saves space

in your luggage compartment, and its

lighter weight helps to improve fuel

economy and permits easier installa-

tion in case of a flat tire.

D Never get under the vehicle

when the vehicle is supported

by the jack alone.

187

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

—Required tools and spare

tire

The compact spare tire can be used

many times, if necessary. It has tread

life of up to 4800 km (3000 miles) de-

pending on road conditions and your

driving habits. When tread wear indi-

cators appear on the tire, replace the

tire.

See also the tire information on page

232 in Section 7−2 for details on the

tread wear indicators and other ser-

vice information.

D The standard tire should be re-

paired and reinstalled as soon

as possible.

D Avoid sudden acceleration,

sudden deceleration and sharp

turns with the compact spare

tire.

NOTICE

Your ground clearance is re-

duced when the compact spare

tire is installed so avoid driving

over obstacles and drive slowly

on rough, unpaved roads and

speed bumps. Also, do not at-

tempt to go through an auto-

matic car wash as the vehicle

may get caught, resulting in

damage.

CAUTION

Vehicles with compact spare tire

D The compact spare tire was de-

signed especially for your Toy-

ota. Do not use it on any other

vehicle.

D Do not use more than one com-

pact spare tire at the same

time.

D Do not exceed 80 km/h (50

mph) when driving with the

compact spare tire.

Vehicles without compact spare

tire

188

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

1. Get the required tools and

spare tire.

Vehicles with compact spare tire

1. Wheel nut wrench

2. Jack handle

3. Tool holder

4. Jack

5. Spare tire

Vehicles without compact spare

tire

1. Tool bag

2. Jack

3. Spare tire

Turn the jack joint by hand.

To remove the spare tire:

To remove: Turn the joint in direction

1 until the jack is free.

To store: Turn the joint in direction 2

until the jack is firmly secured to pre-

vent it flying forward during a collision

or sudden braking.

1. Raise the luggage compartment

floor.

2. On vehicles with compact spare

tire, take the tool holder with tools

out.

To prepare yourself for an emergency,

you should familiarize yourself with

the use of the jack, each of the tools

and their storage locations.

3. Loosen the bolt with spacer and

remove it.

Then take the spare tire out of the

vehicle.

189

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

—Removing wheel ornament

(steel wheels only)

—Blocking the wheel

When storing the spare tire, put it in

place with the outer side of the wheel

facing up. Then secure the tire by re-

peating the above removal steps in

reverse order to prevent it from flying

forward during a collision or sudden

braking.

2. Block the wheel diagonally op-

posite the flat tire to keep the

vehicle from rolling when it is

jacked up.

3. Remove the wheel ornament.

Pry off the wheel ornament, using the

beveled end of the wheel nut wrench

as shown.

When blocking the wheel, place a

wheel block in front of one of the front

wheels or behind one of the rear

wheels.

CAUTION

Do not try to pull off the orna-

ment by hand. Take due care in

handling the ornament to avoid

unexpected personal injury.

190

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

—Loosening wheel nuts

—Positioning the jack

CAUTION

Never use oil or grease on the

bolts or nuts. The nuts may loose

and the wheels may fall off,

which could cause a serious ac-

cident.

4. Loosen all the wheel nuts.

5. Position the jack at the correct

jack point as shown.

Always loosen the wheel nuts before

raising the vehicle.

Make sure the jack is positioned on

a level and solid place.

Turn the wheel nuts counterclockwise

to loosen. To get maximum leverage,

fit the wrench to the nut so that the

handle is on the right side, as shown

above. Grab the wrench near the end

of the handle and pull up on the han-

dle. Be careful that the wrench does

not slip off the nut.

Do not remove the nuts yet—just un-

screw them about one−half turn.

191

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

—Raising your vehicle

—Changing wheels

CAUTION

Never get under the vehicle when

the vehicle is supported by the

jack alone.

6. After making sure that no one

is in the vehicle, raise it high

enough so that the spare tire

can be installed.

7. Remove the wheel nuts and

change tires.

Lift the flat tire straight off and put it

aside.

Remember you will need more ground

clearance when putting on the spare

tire than when removing the flat tire.

To raise the vehicle, insert the jack

handle into the jack (it is a loose fit)

and turn it clockwise. As the jack

touches the vehicle and begins to lift,

double−check that it is properly posi-

tioned.

Roll the spare wheel into position and

align the holes in the wheel with the

bolts. Then lift up the wheel and get

at least the top bolt started through

its hole. Wiggle the tire and press it

back over the other bolts.

192

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

—Reinstalling wheel nuts

CAUTION

Never use oil or grease on the

bolts or nuts. Doing so may lead

to overtightening the nuts and

damaging the bolts. The nuts

may loose and the wheels may

fall off, which could cause a seri-

ous accident. If there is oil or

grease on any bolt or nut, clean

it.

Before putting on wheels, remove any

corrosion on the mounting surfaces

with a wire brush or such. Installation

of wheels without good metal−to−met-

al contact at the mounting surface can

cause wheel nuts to loosen and

eventually cause a wheel to come off

while driving.

8. Reinstall all the wheel nuts fin-

ger tight.

Reinstall the wheel nuts (tapered end

inward) and tighten them as much as

you can by hand. Press back on the

tire and see if you can tighten them

more.

193

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

—Reinstalling wheel ornament

(steel wheels only)

—Lowering your vehicle

CAUTION

D When lowering the vehicle,

make sure all portions of your

body and all other persons

around will not be injured as

the vehicle is lowered to the

ground.

D Have the wheel nuts tightened

by torque wrench at 103 N·m

(10.5 kgf·m, 76 ft·lbf), as soon

as possible after changing

wheels. Otherwise, the nuts

may loosen and the wheels

may fall off, which could cause

a serious accident.

9. Lower the vehicle completely

and tighten the wheel nuts.

10.Reinstall the wheel ornament.

1. Put the wheel ornament into posi-

tion.

Align the cutout of the wheel orna-

ment with the valve stem as shown.

2. Tap it firmly with the side or heel

of your hand to snap it into place.

Turn the jack handle counterclock-

wise to lower the vehicle.

Use only the wheel nut wrench to

tighten the nuts. Do not use other

tools or any additional leverage other

than your hands, such as a hammer,

pipe or your foot. Make sure the

wrench is securely engaged over the

nut.

Tighten each nut a little at a time in

the order shown. Repeat the process

until all the nuts are tight.

CAUTION

Take due care in handling the or-

nament to avoid unexpected per-

sonal injury.

194

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

—After changing wheels

If your vehicle becomes stuck

If your vehicle becomes stuck in snow,

mud, sand, etc., then you may attempt

to rock the vehicle free by moving it

forward and backward.

11.Check the air pressure of the re-

placed tire.

CAUTION

Adjust the air pressure to the specifi-

cation designed on page 255 in Sec-

tion 8. If the pressure is lower, drive

slowly to the nearest service station

and fill to the correct pressure.

Do not forget to reinstall the tire infla-

tion valve cap as dirt and moisture

could get into the valve core and

possibly cause air leakage. If the cap

is missing, have a new one put on as

soon as possible.

Before driving, make sure all the

tools, jack and flat tire are se-

curely in place in their storage

location to reduce the possibility

of personal injury during a colli-

sion or sudden braking.

CAUTION

Do not attempt to rock the vehicle

free by moving it forward and back-

ward if people or objects are any-

where near the vehicle. During the

rocking operation the vehicle may

suddenly move forward or backward

as it becomes unstuck, causing injury

or damage to nearby people or ob-

jects.

12.Restow all the tools, jack and

flat tire securely.

As soon after changing wheels as

possible, tighten the wheel nuts to the

torque specified on page 255 in Sec-

tion 8 with a torque wrench. Have a

technician repair the flat tire and re-

place the spare tire with it.

195

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

If your vehicle needs to be

towed—

If towing is necessary, we recommend

you to have it done by your Toyota

dealer or a commercial tow truck ser-

vice. In consultation with them, have

your vehicle towed using either (a) or

(b).

NOTICE

(a) Towing with wheel lift type truck—

—From front

If you rock your vehicle, observe the

following precautions to prevent dam-

age to the transmission and other

parts.

Only when you cannot receive a towing

service from a Toyota dealer or com-

mercial tow truck service, tow your ve-

hicle carefully in accordance with the

instructions given in “—Emergency tow-

ing” on page 198 in this Section.

z Do not depress the accelerator ped-

al while shifting the selector lever

or before the transmission is com-

pletely shifted to forward or reverse

gear.

—From rear

z Do not race the engine and avoid

Proper equipment will help ensure that

your vehicle is not damaged while being

towed. Commercial operators are generally

aware of the state/provincial and local

laws pertaining to towing.

spinning the wheels.

z If your vehicle remains stuck after

rocking the vehicle several times,

consider other ways such as tow-

ing.

Your vehicle can be damaged if it is

towed incorrectly. Although most operators

know the correct procedure, it is possible

to make a mistake. To avoid damage to

your vehicle, make sure the following pre-

cautions are observed. If necessary, show

this page to the tow truck driver.

(b) Using flat bed truck

TOWING PRECAUTIONS:

Use a safety chain system for all towing,

and abide by the state/provincial and local

laws. The wheels and axle on the ground

must be in good condition. If they are

damaged, use a towing dolly.

196

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

(a) Towing with wheel lift type truck

D Automatic transmission:

Use towing dolly under the front

wheels.

(c) Towing with sling type

From front—Release the parking brake.

a

truck

NOTICE

When lifting wheels, take care to en-

sure adequate ground clearance for

towing at the opposite end of the

raised vehicle. Otherwise, the bumper

and/or underbody of the towed vehicle

will be damaged during towing.

Never tow a vehicle with an automatic

transmission from the rear with the

front wheels on the ground, as this

may cause serious damage to the

transmission.

(b) Using flat bed truck

From rear—

D Manual transmission:

(c) Towing with sling type truck

We recommend using

a

towing dolly

under the front wheels. If you do not

use a towing dolly, place the ignition

key in the “ACC” position and put the

transmission in neutral.

NOTICE

Do not tow with sling type truck, ei-

ther from the front or rear. This may

cause body damage.

NOTICE

Do not tow with the key removed or

in the “LOCK” position when towing

from the rear without a towing dolly.

The steering lock mechanism is not

strong enough to hold the front

wheels straight.

197

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

—Emergency towing

A driver must be in the vehicle to steer

it and operate the brakes.

Before towing, release the parking brake

and put the transmission in neutral (manu-

al) or “N” (automatic). The key must be

in “ACC” (engine off) or “ON” (engine run-

ning).

Towing in this manner may be done only

on hard−surfaced roads for a short dis-

tance and at low speeds. Also, the

wheels, axles, drive train, steering and

brakes must all be in good condition.

CAUTION

If the engine is not running, the pow-

er assist for the brakes and steering

will not work so steering and braking

will be much harder than usual.

CAUTION

Use extreme caution when towing ve-

hicles. Avoid sudden starts or erratic

driving maneuvers which would place

excessive stress on the emergency

towing eyelet and towing cable or

chain. The eyelet and towing cable or

chain may break and cause serious

injury or damage.

If towing is necessary, we recommend

you to have it done by your Toyota

dealer or a commercial tow truck ser-

vice.

If towing service is not available in an

emergency, your vehicle may be tempo-

rarily towed by a cable or chain se-

cured to the emergency towing eyelet

under the vehicle. Use extreme caution

when towing vehicles.

NOTICE

Use only a cable or chain specifically

intended for use in towing vehicles.

Securely fasten the cable or chain to

the towing eyelet provided.

NOTICE

Only use specified towing eyelet;

otherwise your vehicle may be dam-

aged.

198

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

If you cannot shift automatic

transmission selector lever

If you lose your keys

You can purchase a new key at your

Toyota dealer if you can give them the

key number.

See the suggestion given in “Keys” on

page 10 in Section 1−2.

If your keys are locked in the vehicle and

you cannot get a duplicate, many Toyota

dealers can still open the door for you,

using their special tools. If you must

break

a

window to get in, we suggest

breaking the smallest side window be-

cause it is the least expensive to replace.

Be extremely cautious to avoid cuts from

the glass.

If you cannot shift the selector lever

out of “P” position to other positions

even though the brake pedal is de-

pressed, use the shift lock override but-

ton as follows:

3. Insert your finger into the hole to

push down the shift lock override

button. You can shift out of “P”

position only while pushing the but-

ton.

1. Turn the ignition key to “LOCK”

position. Make sure the parking

brake is applied.

4. Shift into “N” position.

5. Insert the cover.

6. Start the engine. For your safety,

keep the brake pedal depressed.

2. Pry up the cover with a flat−bladed

screwdriver or equivalent.

Be sure to have the system checked by

your Toyota dealer as soon as possible.

199

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

’04 Corolla_U (L/O 0306)

If you lose your wireless

remote control transmitter

You can purchase a new wireless re-

mote control transmitter at your Toyota

dealer.

Have the registered identification numbers

of your transmitters deleted from your ve-

hicle by your Toyota dealer as soon as

possible to avoid the possibility of theft or

an accident. Then, have the identification

number of your new transmitter registered.

At the same time, you must bring all of

the remaining transmitters to have them

registered again as well.

You can use the wireless remote control

system with the new transmitter. Contact

your Toyota dealer for detailed information.

200

2004 COROLLA from Oct. ’03 Prod. (OM12859U)

In case of an emergency for Your Toyota Corolla 4 Door Eighth Generation (2000-2006)

Related Topics

Popular Owner Manuals

Latest Owner Manuals