2000-2006 Toyota Corolla 4 Door Occupant restraint systems -> Seat belts User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Occupant restraint systems -> Seat belts for Your Toyota Corolla 4 Door Eighth Generation (2000-2006)

’04 Corolla_U (L/O 0306)  
Seat belts—  
—Seat belt precautions  
For your safety and comfort, adjust the  
head restraint before driving.  
Toyota strongly urges that the driver and  
passengers in the vehicle be properly re-  
strained at all times with the seat belts  
provided. Failure to do so could increase  
the chance of injury and/or the severity of  
injury in accidents.  
Do not allow any children to stand up or  
kneel on either rear or front seats. An  
unrestrained child could suffer serious in-  
jury or death during emergency braking or  
a collision. Also, do not let the child sit  
on your lap. Holding a child in your arms  
does not provide sufficient restraint.  
To raise: Pull it up.  
To lower: Push it down while pressing the  
lock release button.  
The head restraint is most effective when  
it is close to your head. Therefore, using  
a cushion on the seatback is not recom-  
mended.  
The seat belts provided for your vehicle  
are designed for people of adult size,  
large enough to properly wear them.  
Pregnant woman. Toyota recommends the  
use of a seat belt. Ask your doctor for  
specific recommendations. The lap belt  
should be worn securely and as low as  
possible over the hips and not on the  
waist.  
Child. Use a child restraint system ap-  
propriate for the child until the child be-  
comes large enough to properly wear the  
vehicle’s seat belts. See “Child restraint”  
on page 53 in this Section for details.  
CAUTION  
D Adjust the center of the head re-  
straint so that it is closest to the  
top of your ears.  
Injured person. Toyota recommends the  
use of a seat belt. Depending on the inju-  
ry, first check with your doctor for specific  
recommendations.  
If a child is too large for a child restraint  
system, the child should sit in the rear  
seat and must be restrained using the  
vehicle’s seat belt. According to accident  
statistics, the child is safer when properly  
restrained in the rear seat than in the  
front seat.  
D After adjusting the head restraint,  
make sure it is locked in position.  
D Do not drive with the head re-  
straints removed.  
If a child must sit in the front seat, the  
seat belts should be worn properly. If an  
accident occurs and the seat belts are not  
worn properly, the force of the rapid infla-  
tion of the airbag may cause death or  
serious injury to the child.  
33  
2004 COROLLA from Oct. ’03 Prod. (OM12859U)  
’04 Corolla_U (L/O 0306)  
—Fastening front and rear  
seat belts  
D Be careful not to damage the belt  
webbing or hardware. Take care that  
they do not get caught or pinched  
in the seat or doors.  
CAUTION  
Tab  
Persons should ride in their seats  
properly wearing their seat belts  
whenever the vehicle is moving.  
Otherwise, they are much more likely  
to suffer serious bodily injury or  
death in the event of sudden braking  
or a collision.  
D Inspect the belt system periodically.  
Check for cuts, fraying, and loose  
parts. Damaged parts should be re-  
placed. Do not disassemble or  
modify the system.  
Buckle  
When using the seat belts, observe  
the following:  
D Keep the belts clean and dry. If  
they need cleaning, use a mild soap  
solution or lukewarm water. Never  
use bleach, dye, or abrasive clean-  
ers, or allow them to come into  
contact with the belt—they may se-  
verely weaken the belts. (See  
“Cleaning the interior” on page 205  
in Section 5.)  
D Use the belt for only one person at  
a time. Do not use a single belt for  
two or more people—even children.  
Adjust the seat as needed and sit up  
straight and well back in the seat. To  
fasten your belt, pull it out of the re-  
tractor and insert the tab into the  
buckle.  
D To reduce the risk of sliding under  
the lap belt during  
a
collision,  
avoid reclining the seatback any  
more than needed. The seat belts  
You will hear a click when the tab locks  
into the buckle.  
provide maximum protection in  
a
D Replace the belt assembly (includ-  
ing bolts) if it has been used in a  
severe impact. The entire assembly  
should be replaced even if damage  
is not obvious.  
frontal or rear collision when the  
driver and the front passenger are  
sitting up straight and well back in  
the seats. If you are reclined, the  
lap belt may slide past your hips  
and apply restraint forces directly  
to the abdomen. In the event of a  
frontal collision, the more the seat  
is reclined, the greater the risk of  
personal injury.  
The seat belt length automatically adjusts  
to your size and the seat position.  
The retractor will lock the belt during a  
sudden stop or on impact. It also may  
lock if you lean forward too quickly. A  
slow, easy motion will allow the belt to  
extend, and you can move around freely.  
34  
2004 COROLLA from Oct. ’03 Prod. (OM12859U)  
’04 Corolla_U (L/O 0306)  
When a passenger’s shoulder belt is com-  
pletely extended and is then retracted  
even slightly, the belt is locked in that  
position and cannot be extended. This fea-  
ture is used to hold the child restraint  
system securely. (For details, see “Child  
restraint” on page 53 in this Section.) To  
free the belt again, fully retract the belt  
and then pull the belt out once more.  
CAUTION  
Take up  
D Both high−positioned lap belts and  
loose−fitting belts could cause seri-  
ous injuries due to sliding under  
the lap belt during a collision or  
other unintended event. Keep the  
lap belt positioned as low on hips  
as possible.  
slack  
Too high  
If the seat belt cannot be pulled out of the  
retractor, firmly pull the belt and release  
it. You will then be able to smoothly pull  
the belt out of the retractor.  
D Do not place the shoulder belt un-  
der your arm.  
Keep as low on  
hips as possible  
Adjust the position of the lap and  
shoulder belts.  
CAUTION  
D After inserting the tab, make sure  
the tab and buckle are locked and  
that the belt is not twisted.  
Position the lap belt as low as possible  
on your hips—not on your waist, then ad-  
just it to a snug fit by pulling the shoulder  
portion upward through the latch plate.  
D Do not insert coins, clips, etc. in  
the buckle as this may prevent you  
from properly latching the tab and  
buckle.  
D If the seat belt does not function  
normally, immediately contact your  
Toyota dealer. Do not use the seat  
until the seat belt is fixed, because  
it cannot protect an adult occupant  
or your child from injury.  
35  
2004 COROLLA from Oct. ’03 Prod. (OM12859U)  
’04 Corolla_U (L/O 0306)  
CAUTION  
Always make sure the shoulder belt  
is positioned across the center of  
your shoulder. The belt should be  
kept away from your neck, but not  
falling off your shoulder. Failure to  
do so could reduce the amount of  
protection in an accident and cause  
serious injures in a collision.  
Seat belts with an adjustable shoulder  
anchor—  
To release the belt, press the buckle  
release button and allow the belt to  
retract.  
Adjust the shoulder anchor position to  
your size.  
If the belt does not retract smoothly, pull  
it out and check for kinks or twists. Then  
make sure it remains untwisted as it re-  
tracts.  
To raise: Slide the anchor up.  
To lower: Push in the lock release button  
and slide the anchor down.  
After adjustment, make sure the anchor is  
locked in position.  
36  
2004 COROLLA from Oct. ’03 Prod. (OM12859U)  
’04 Corolla_U (L/O 0306)  
—Seat belt extender  
If your seat belts cannot be fastened se-  
curely because they are not long enough,  
a personalized seat belt extender is avail-  
able from your Toyota dealer free of  
charge.  
D Be sure to wear the seat belt with-  
out the seat belt extender if you  
can fasten the seat belt without the  
extender.  
D Do not use the seat belt extender  
Please contact your local Toyota dealer to  
order the proper required length for the  
extender. Bring the heaviest coat you ex-  
pect to wear for proper measurement and  
selection of length. Additional ordering in-  
formation is available at your Toyota deal-  
er.  
when installing  
system on the front or rear passen-  
ger seat. If installing child re-  
a
child restraint  
a
straint system with the seat belt  
extender connected to the seat belt,  
the seat belt will not securely hold  
the child restraint system, which  
could cause death or serious injury  
to the child or other passengers in  
the event of collision.  
CAUTION  
D If the seat belt extender has been  
connected to the driver’s seat belt  
buckle without wearing the seat belt  
when using the extender in the  
driver’s seat, the SRS driver’s air-  
bag system will judge that the driv-  
er wears the seat belt even if not  
wearing it. In this case, the driver’s  
airbag may not activate correctly,  
causing death or serious injury in  
the event of collision. Be sure to  
wear the seat belt with the seat belt  
extender.  
When using the seat belt extender,  
observe the following precautions.  
Failure to follow these instructions  
could reduce the effectiveness of the  
seat belt restraint system in case of  
an accident, increasing the chance of  
personal injury.  
D Remember that the extender pro-  
vided for you may not be safe when  
used on  
another person, or at  
a
different vehicle, for  
different  
a
seating position than the one origi-  
nally intended.  
37  
2004 COROLLA from Oct. ’03 Prod. (OM12859U)  
’04 Corolla_U (L/O 0306)  
—Seat belt pretensioners  
CAUTION  
D After inserting the tab, make sure  
the tab and buckle are locked and  
that the lap and shoulder portions  
of the belt and the seat belt extend-  
er are not twisted.  
D Do not insert coins, clips, etc. in  
the buckle as this may prevent you  
from properly latching the tab and  
buckle.  
D If the seat belt does not function  
normally, immediately contact your  
Toyota dealer. Do not use the seat  
until the seat belt is fixed, because  
it cannot protect an adult occupant  
or your child from injury.  
To connect the extender to the seat  
belt, insert the tab into the seat belt  
buckle so that the “PRESS” signs on  
the buckle release buttons of the ex-  
tender and the seat belt are both facing  
outward as shown.  
The driver and front passenger seat  
belt pretensioners are designed to be  
activated in response to a severe fron-  
tal impact.  
When the sensor detects a severe frontal  
impact, the front seat belts are quickly  
drawn back by the retractors so that the  
belts snugly restrain the occupants.  
You will hear a click when the tab locks  
into the buckle.  
The seat belt pretensioners are activated  
even with no passenger in the front seat.  
When releasing the seat belt, press on  
the buckle release button on the extender,  
not on the seat belt. This helps prevent  
damage to the vehicle interior and extend-  
er itself.  
The seat belt pretensioners and SRS air-  
bags may not operate together in all colli-  
sions.  
When not in use, remove the extender  
and store in the vehicle for future use.  
38  
2004 COROLLA from Oct. ’03 Prod. (OM12859U)  
’04 Corolla_U (L/O 0306)  
When the seat belt pretensioners are acti-  
NOTICE  
vated, an operating noise may be heard  
and a small amount of nontoxic gas may  
be released. This does not indicate that  
a fire is occurring. This gas is normally  
harmless.  
Do not perform any of the following  
changes without  
consulting your  
Toyota dealer. Such changes can  
interfere with proper operation of the  
seat belt pretensioners in some  
cases.  
Once the seat belt pretensioners have  
been activated, the seat belt retractors  
remain locked.  
z Installation of electronic devices  
such as  
a
mobile two−way radio,  
CAUTION  
cassette tape player or compact  
disc player  
Do not modify, remove, strike or open  
the seat belt pretensioner assemblies,  
airbag sensor or surrounding area or  
wiring. Failure to follow these instruc-  
tions may prevent the seat belt pre-  
tensioners from activating correctly,  
cause sudden operation of the system  
or disable the system, which could  
result in death or serious injury. Con-  
sult your Toyota dealer about any re-  
pair and modification.  
z Repairs on or near the front seat  
belt retractor assemblies  
The seat belt pretensioner system con-  
sists mainly of the following components  
and their locations are shown in the il-  
lustration.  
z Modification of the suspension sys-  
tem  
z Modification of the front end struc-  
ture  
1. Front airbag sensors  
z Attachment of a grille guard (bull  
bar, kangaroo bar, etc.), snowplow,  
winches or any other equipment to  
the front end  
2. Seat belt pretensioner assemblies  
3. Airbag sensor assembly  
4. SRS warning light  
z Repairs made on or near the front  
fenders, front end structure or con-  
sole  
The seat belt pretensioners are controlled  
by the airbag sensor assembly. The airbag  
sensor assembly consists of a safing sen-  
sor and airbag sensor.  
39  
2004 COROLLA from Oct. ’03 Prod. (OM12859U)  
’04 Corolla_U (L/O 0306)  
If any of the following conditions occurs,  
this indicates a malfunction of the airbags  
or seat belt pretensioners. Contact your  
Toyota dealer as soon as possible.  
D When the ignition key is turned to the  
“ON” position, the light does not come  
on, remains on or flashes.  
D The light comes on or starts flashing  
while driving.  
D If any seat belt does not retract or can  
not be pulled out due to a malfunction  
or activation of the relevant seat belt  
pretensioner.  
This indicator comes on when the igni-  
tion key is turned to the “ON” position.  
It goes off after about 6 seconds. This  
means the front seat belt pretensioners  
are operating properly.  
In the following cases, contact your Toyota  
dealer as soon as possible:  
D The seat belt pretensioner assembly or  
surrounding area has been damaged.  
D The front of the vehicle (shaded in the  
illustration) was involved in an accident  
that was not severe enough to cause  
the seat belt pretensioners to operate.  
This warning light system monitors the  
airbag sensor assembly, front airbag sen-  
sors, side airbag sensors, driver’s seat  
position sensor, driver’s seat belt buckle  
switch, seat belt pretensioner assemblies,  
inflators, warning light, interconnecting wir-  
ing and power sources. (For details, see  
“Service reminder indicators and warning  
buzzers” on page 88 in Section 16.)  
D Either seat belt pretensioner assembly  
or surrounding area is scratched,  
cracked, or otherwise damaged.  
40  
2004 COROLLA from Oct. ’03 Prod. (OM12859U)  

Related Topics

Popular Owner Manuals