Maintenanceandcare -> 7-1. Maintenance and care for Your Toyota Prius 4 Door Fifth Generation (2023-2026)

486  
7-1. Maintenance and care  
7-1.Maintenance and care  
vehicle. Make sure to extend the  
mirrors before driving.  
Cleaning and protect-  
ing the vehic le ex te-  
rior  
Brushes used in automatic car  
washes may scratch the vehicle  
surface, parts (wheel, etc.) and  
harm your vehicle’s paint.  
Perform the following to  
protect the vehicle and  
maintain it in prime condi-  
tion:  
Rear spoiler may not be washable  
in some automatic car washes.  
There may also be an increased  
risk of damage to vehicle.  
When the shift position needs to  
be held in N, refer to P.259.  
Cleaning instructions  
If you need to release the parking  
brake, turn off the brake hold sys-  
tem, release the parking brake,  
and set the power switch to ACC  
while holding the N position.  
(P.263)  
Working from top to bottom,  
liberally apply water to the  
vehicle body, wheel wells and  
underside of the vehicle to  
remove any dirt and dust.  
High pressure car washes  
As water may enter the cabin, do  
not bring the nozzle tip near the  
gaps around the doors or perimeter  
of the windows, or spray these  
areas continuously.  
Wash the vehicle body using  
a sponge or soft cloth, such  
as a chamois.  
For hard-to-remove marks,  
use car wash soap and rinse  
thoroughly with water.  
Note for a smart key system  
If the door handle becomes wet  
while the electronic key is within the  
effective range, the door may lock  
and unlock repeatedly. In that case,  
follow the following correction pro-  
cedures to wash the vehicle:  
Wipe away any water.  
Wax the vehicle when the  
waterproof coating deterio-  
rates.  
Place the key in a position 6 ft. (2  
m) or more separate from the  
vehicle while the vehicle is being  
washed. (Take care to ensure that  
the key is not stolen.)  
If water does not bead on a clean  
surface, apply wax when the vehi-  
cle body is cool.  
Set the electronic key to battery-  
saving mode to disable the smart  
key system. (P.205)  
Before car washes  
Wheels and wheel ornaments  
(vehicles without matte painted  
wheels)  
Check that the fuel filler door and  
charging port lid on your vehicle are  
closed properly.  
Remove any dirt immediately by  
using a neutral detergent.  
Automatic car washes  
Before washing the vehicle:  
• Fold the mirrors  
• Turn off the power back door  
Wash detergent off with water  
immediately after use.  
To protect the paint from damage,  
make sure to observe the follow-  
Start washing from the front of the  
487  
7-1. Maintenance and care  
ing precautions.  
rotors, causing them to stick. Before  
parking the vehicle after it is  
washed, drive slowly and apply the  
brakes several times to dry the  
parts.  
• Do not use acidic, alkaline or  
abrasive detergent  
• Do not use hard brushes  
• Do not use detergent on the  
wheels when they are hot, such  
as after driving or parking in hot  
weather  
Bumpers  
Do not scrub with abrasive cleaners.  
Front side windows water-  
Wheels and wheel ornaments  
(vehicles with matte painted  
wheels)  
repellent coating (if equipped)  
The following precautions can  
extend the effectiveness of the  
water-repellent coating.  
A different set of care is necessary  
for matte painted wheels and wheel  
ornaments.  
Remove any dirt, etc., from the  
front side windows regularly.  
Contact your Toyota dealer for  
details.  
Do not allow dirt and dust to accu-  
mulate on the windows for a long  
period. Clean the windows with a  
soft, damp cloth as soon as possi-  
ble.  
Remove dirt using water as early  
as possible.  
If the wheels are excessively dirty,  
use diluted neutral detergent.  
Do not use wax or glass cleaners  
that contain abrasives when  
cleaning the windows.  
When using detergent, make sure  
to rinse it off with water immedi-  
ately. Then use a soft cloth to  
wipe off the water.  
Do not use any metallic objects to  
remove condensation build up.  
Use a sponge or soft cloth to  
remove the dirt by hand.  
Plated portions  
To prevent the matte paint from  
being damaged or glossy, make  
sure to observe the following pre-  
cautions:  
• Do not apply any coatings or wax.  
• Do not use acidic, alkaline or  
abrasive detergents.  
If dirt cannot be removed, clean the  
parts as follows:  
Use a soft cloth dampened with  
an approximately 5% solution of  
neutral detergent and water to  
clean the dirt off.  
7
• When using tire cleaners or tire  
wax, do not allow them to be  
applied to the wheels.  
• Do not scrub or polish the wheels  
using a brush or dry cloth, etc.  
• When using an automatic car  
wash, do not select the wheel  
brush function.  
Wipe the surface with a dry, soft  
cloth to remove any remaining  
moisture.  
To remove oily deposits, use alco-  
hol wet wipes or a similar product.  
WARNING  
• Do not use a high pressure  
washer or steam cleaner.  
• Do not use detergent on the  
wheels when they are hot, such  
as after driving or parking in hot  
weather.  
When washing the vehicle  
Do not apply water to the inside of  
the engine compartment. Doing  
so may cause the electrical com-  
ponents, etc. to catch fire.  
Brake pads and calipers  
Rust may form if the vehicle is  
parked with wet brake pads or disc  
488  
7-1. Maintenance and care  
WARNING  
Precautions regarding the  
exhaust pipe  
While charging  
Exhaust gasses cause the  
exhaust pipe to become quite hot.  
Do not wash the vehicle.  
Doing so may cause the electrical  
components to malfunction or  
catch fire and also you may get an  
electric shock that may result in  
death or serious injury.  
When washing the vehicle, be  
careful not to touch the pipe until it  
has cooled sufficiently, as touch-  
ing a hot exhaust pipe can cause  
burns.  
When cleaning the windshield  
Precaution regarding the  
front and rear bumpers  
Set the wiper switch to off.  
If the wiper switch is in “AUTO”,  
the wipers may operate unexpect-  
edly in the following situations,  
and may result in hands being  
caught or other serious injuries  
and cause damage to the wiper  
blades.  
If the paint of the front or rear  
bumper is chipped or scratched,  
the following systems may not  
function correctly. If this occurs,  
consult your Toyota dealer.  
• BSM (if equipped)  
• RCTA (if equipped)  
• SEA (if equipped)  
• PKSB (if equipped)  
• Intuitive parking assist  
• Toyota Safety Sense 3.0  
A
Off  
B
AUTO  
When the upper part of the  
windshield where the raindrop  
sensor is located is touched by  
hand  
When a wet rag or similar is  
held close to the raindrop sen-  
sor  
If something bumps against the  
windshield  
If you directly touch the raindrop  
sensor body or if something  
bumps into the raindrop sensor  
489  
7-1. Maintenance and care  
Do not apply wax to the sur-  
NOTICE  
faces of the lights.  
To prevent paint deterioration  
and corrosion on the body  
and components (aluminum  
wheels, etc.)  
Wax may cause damage to the  
lenses.  
Cleaning the radiator grille  
Observe the following precautions  
to avoid damage to the radiator  
grille surface.  
Wash the vehicle immediately in  
the following cases:  
• After driving near the sea coast  
• After driving on salted roads  
Do not use a hard brush. Use a  
soft cloth or sponge to wipe.  
• If coal tar or tree sap is present  
on the paint surface  
Remove any dirt by using a  
neutral detergent. Do not use  
waxes or alcohols (e.g. glass  
cleaner).  
• If dead insects, insect droppings  
or bird droppings are present on  
the paint surface  
Wash detergent off with water  
• After driving in an area contami-  
nated with soot, oily smoke,  
mine dust, iron powder or chem-  
ical substances  
after washing the vehicle.  
When using an automatic car  
wash  
• If the vehicle becomes heavily  
soiled with dust or mud  
Set the wiper switch to off posi-  
tion.  
If the wiper switch is in “AUTO”,  
the wipers may operate and the  
wiper blades may be damaged.  
• If liquids such as benzene and  
gasoline are spilled on the paint  
surface  
If the paint is chipped or  
scratched, have it repaired  
immediately.  
When using a high pressure  
car wash  
When washing the vehicle, do  
not spray the camera or its sur-  
rounding area directly with a  
high pressure washer. Shock  
applied from high pressure  
water may cause the device to  
not operate normally.  
To prevent the wheels from cor-  
roding, remove any dirt and  
store in a place with low humid-  
ity when storing the wheels.  
7
To prevent damage to the  
windshield wiper arms  
Do not spray water directly on  
the radar which is equipped  
behind the emblem. Otherwise  
it may cause the device to be  
damaged.  
When lifting the wiper arms away  
from the windshield pull the driver  
side wiper arm upward first, and  
repeat for the passenger’s side.  
When returning the wipers to their  
original position, do so from the  
passenger’s side first.  
Cleaning the exterior lights  
Wash carefully. Do not use  
organic substances or scrub  
with a hard brush.  
This may damage the surfaces  
of the lights.  
490  
7-1. Maintenance and care  
Cleaning and protect-  
ing the vehicle interior  
NOTICE  
Do not bring the nozzle tip close  
to boots (rubber or resin manu-  
factured cover), connectors or  
the following parts. The parts  
may be damaged if they come  
into contact with high-pressure  
water.  
Perform cleaning in a man-  
ner appropriate to each  
component and its material.  
• Traction related parts  
• Steering parts  
Protecting the vehicle  
interior  
• Suspension parts  
• Brake parts  
Remove dirt and dust using a  
vacuum cleaner. Wipe dirty  
surfaces with a cloth damp-  
ened with lukewarm water.  
Keep the cleaning nozzle at  
least 11.9 in. (30 cm) away from  
the vehicle body. Otherwise  
resin section, such as moldings  
and bumpers, may be deformed  
and damaged. Also, do not con-  
tinuously hold the nozzle in the  
same place.  
If dirt cannot be removed,  
wipe it off with a soft cloth  
dampened with neutral deter-  
gent diluted to approximately  
1%.  
Do not spray the lower part of  
the windshield continuously. If  
water enters the air conditioning  
system intake located near the  
lower part of the windshield, the  
air conditioning system may not  
operate correctly.  
Wring out any excess water  
from the cloth and thoroughly  
wipe off remaining traces of  
detergent and water.  
Do not wash the underside of  
the vehicle using a high pres-  
sure car washer.  
Shampooing the carpets  
There are several commercial foam-  
ing-type cleaners available. Use a  
sponge or brush to apply the foam.  
Rub in overlapping circles. Do not  
use water. Wipe dirty surfaces and  
let them dry. Excellent results are  
obtained by keeping the carpet as  
dry as possible.  
Do not use the washer on the  
area around the charging port  
lid. Water could get into the AC  
charging inlet and could dam-  
age the vehicle.  
Handling the seat belts  
Clean with mild soap and lukewarm  
water using a cloth or sponge. Also  
check the belts periodically for  
excessive wear, fraying or cuts.  
Front side windows with UV  
protective coating (if equipped)  
The front side windows have UV  
protective coating. To prevent any  
491  
7-1. Maintenance and care  
damage to the UV protective coat-  
ing, observe the following:  
NOTICE  
Cleaning detergents  
If the windows are dirty, gently  
wipe them with a cloth soaked in  
water or lukewarm water as soon  
as possible.  
Do not use the following types  
of detergent, as they may dis-  
color the vehicle interior or  
cause streaks or damage to  
painted surfaces:  
If the windows are very dirty, do  
not open and close them repeat-  
edly.  
• Non-seat portions: Organic sub-  
stances such as benzene or  
gasoline, alkaline or acidic solu-  
tions, dye, and bleach  
WARNING  
Water in the vehicle  
• Seats: Alkaline or acidic solu-  
tions, such as thinner, benzene,  
and alcohol  
Do not splash or spill liquid in  
the vehicle, such as on the floor,  
on the rear seats or in the lug-  
gage compartment.  
Doing so may cause the hybrid  
battery, electrical components,  
etc. to malfunction or catch fire.  
Do not use polish wax or polish  
cleaner. The instrument panel’s  
or other interior part’s painted  
surface may be damaged.  
Preventing damage to leather  
Do not get any of the SRS com-  
ponents or wiring in the vehicle  
interior wet.  
surfaces  
Observe the following precautions  
to avoid damage to and deteriora-  
tion of leather surfaces:  
(P.36)  
An electrical malfunction may  
cause the airbags to deploy or  
not function properly, resulting  
in death or serious injury.  
Remove any dust or dirt from  
leather surfaces immediately.  
Do not expose the vehicle to  
direct sunlight for extended peri-  
ods of time. Park the vehicle in  
the shade, especially during  
summer.  
Do not let the wireless charger  
(P.458) get wet. Failure to do  
so may cause the charger to  
become hot and cause burns or  
could cause electric shock  
resulting in death or serious  
injury.  
7
Do not place items made of  
vinyl, plastic, or containing wax  
on the upholstery, as they may  
stick to the leather surface if the  
vehicle interior heats up signifi-  
cantly.  
Cleaning the interior (espe-  
cially instrument panel)  
Do not use polish wax or polish  
cleaner. The instrument panel  
may reflect off the windshield,  
obstructing the driver’s view and  
leading to an accident, resulting in  
death or serious injury.  
Water on the floor  
Do not wash the vehicle floor with  
water.  
Vehicle systems such as the  
audio system may be damaged if  
water comes into contact with  
electrical components such as the  
audio system above or under the  
floor of the vehicle. Water may  
also cause the body to rust.  
492  
7-1. Maintenance and care  
to clean them regularly. If dirty areas  
are left uncleaned for long periods  
of time, they may be difficult to  
clean.  
NOTICE  
When cleaning the inside of  
the windshield  
Do not allow glass cleaner to con-  
tact the lens. Also, do not touch  
the lens. (P.284)  
Cleaning the leather areas  
Remove dirt and dust using a  
Cleaning the inside of the rear  
window  
vacuum cleaner.  
Do not use a glass cleaner to  
clean the rear window, as this  
may cause damage to the rear  
window defogger heater wires  
or antenna. Use a cloth damp-  
ened with lukewarm water to  
gently wipe the window clean.  
Wipe the window in strokes run-  
ning parallel to the heater wires  
or antenna.  
Wipe off any excess dirt and  
dust with a soft cloth damp-  
ened with diluted detergent.  
Use a diluted water solution of  
approximately 5% neutral wool  
detergent.  
Wring out any excess water  
from the cloth and thoroughly  
wipe off all remaining traces  
of detergent.  
Be careful not to scratch or  
damage the heater wires or  
antenna.  
Wipe the surface with a dry,  
soft cloth to remove any  
remaining moisture. Allow the  
leather to dry in a shaded and  
ventilated area.  
Cleaning the front side win-  
dow  
Do not use any compound or  
abrasive product (e.g., glass  
cleaner, detergent, wax) to clean  
the windows. It may damage the  
coating.  
Caring for leather areas  
Toyota recommends cleaning the  
interior of the vehicle at least twice a  
year to maintain the quality of the  
vehicle’s interior.  
Cleaning the areas with  
satin-finish metal accents  
(if equipped)  
Remove dirt using a water-  
dampened soft cloth or syn-  
thetic chamois.  
Cleaning the synthetic  
leather areas  
Remove dirt and dust using a  
Wipe the surface with a dry,  
soft cloth to remove any  
remaining moisture.  
vacuum cleaner.  
Wipe it off with a soft cloth  
dampened with neutral deter-  
gent diluted to approximately  
1%.  
Cleaning the areas with satin-  
finish metal accents  
The metal areas use a layer of real  
metal for the surface. It is necessary  
Wring out any excess water  
493  
7-1. Maintenance and care  
from the cloth and thoroughly  
wipe off remaining traces of  
detergent and water.  
7