Get Vehiclestatusinformationandindicators Guide for Toyota Prius 4 Door Fifth Generation (2023-2026)

149

Vehicle status informa-

tion and indicators

3

3-1. Instrument cluster

Warning lights and indica-

tors ............................ 150

Gauges and meters .... 155

Multi-information display

.................................. 161

Energy monitor/consump-

tion screen/solar charging

information screen..... 173

3

150

3-1. Instrument cluster

3-1.Instrument cluster

Warning lights and indicators

The warning lights and indicators on the instrument cluster,

overhead console panel and outside rear view mirrors inform

the driver of the status of the vehicle’s various systems.

Instrument cluster

For the purpose of explanation, the following illustrations display all

warning lights and indicators illuminated.

The units used on the meters and some indicators may differ depending on

the target region.

Warning lights

Brake system warning

*1

light (P.555)

Warning lights inform the driver

of malfunctions in the indicated

vehicle’s systems.

(Yellow)

Charging system warning

*2

light (P.555)

High coolant temperature

warning light (P.556)

Brake system warning

*1

light (P.555)

(U.S.A.)

Low engine oil pressure

*2

warning light (P.556)

Hybrid system overheat

*2

Brake system warning

*1

light (P.555)

(Canada)

(Red)

warning light (P.556)

151

3-1. Instrument cluster

Intuitive parking assist

*3

Malfunction indicator

*1

OFF indicator (P.560)

*1

lamp (P.556)

(U.S.A.)

Slip indicator light

(P.560)

Inappropriate pedal opera-

*2

Malfunction indicator

*1

lamp (P.556)

(Canada)

tion warning light

(P.560)

*1

SRS warning light

(P.557)

Brake hold operated indi-

*1

cator (P.561)

ABS warning light

(P.557)

(Flashes)

(U.S.A.)

Parking brake indicator

(P.561)

*1

ABS warning light

(P.557)

3

(U.S.A.)

(Flashes)

(Canada)

Electric power steering

*1

Parking brake indicator

(P.561)

system warning light

(Canada)

(Flashes)

(P.558)

Electric power steering

*1

(Red)

Tire pressure warning

*1

system warning light

(P.558)

*1

light (P.561)

(Yellow)

Low fuel level warning

light (P.562)

PCS warning light

(P.558)

Driver’s and front passen-

ger’s seat belt reminder

light (P.562)

LTA indicator (P.558)

(Yellow)

Rear passengers’

seat belt reminder

light (P.562)

LDA indicator (P.558)

PDA indicator (P.559)

*1

:These lights turn on when the

power switch is turned to ON to

indicate that a system check is

being performed. They will turn

off after the hybrid system is on,

or after a few seconds. There

may be a malfunction in a sys-

tem if the light does not come on,

or turn off. Have the vehicle

Cruise control indicator

(P.559)

Dynamic radar cruise con-

trol indicator (P.559)

inspected by your Toyota dealer.

Driving assist information

*1

*2

:This light illuminates on the

multi-information display with a

message.

indicator (P.559)

152

3-1. Instrument cluster

*3

:Intuitive parking assist OFF indi-

cator turns on when the power

switch is turned to ON while the

Intuitive parking assist function is

on. It will turn off after a few sec-

onds.

LTA indicator (P.309)

(White)

(Green)

WARNING

■If a safety system warning

light does not come on

LTA indicator (P.309)

(Yellow)

Should a safety system light such

as the ABS and SRS warning light

not come on when you start the

hybrid system, this could mean

that these systems are not avail-

able to help protect you in an acci-

dent, which could result in death

or serious injury. Have the vehicle

inspected by your Toyota dealer

immediately if this occurs.

(Flashes)

*10

LDA indicator (P.317)

(White)

(Green)

LDA indicator (P.317)

Indicators

(Yellow)

(Flashes)

The indicators inform the driver

of the operating state of the

vehicle’s various systems.

*2, 9

LDA OFF indicator

(P.317)

PDA indicator (P.324)

Turn signal indicator

(White)

(Green)

(White)

(Green)

(White)

(Green)

(P.262)

Headlight indicator

(P.269)

PDA indicator (P.324)

(U.S.A.)

Cruise control indicator

(P.344)

Tail light indicator

(P.269)

(Canada)

Headlight high beam indi-

cator (P.271)

Cruise control indicator

(P.344)

AHB indicator (P.272)

Dynamic radar cruise con-

trol indicator (P.340)

Smart key system indica-

*1

tor (P.251)

Dynamic radar cruise con-

trol indicator (P.340)

153

3-1. Instrument cluster

Intuitive parking assist

*2, 3

AUTO EV/HV mode indi-

*8

OFF indicator

(P.364)

cator (P.73)

*8

HV drive mode indicator

(P.73)

Hybrid battery charge

*4

Slip indicator light

(P.425)

*8

(Flashes)

mode indicator (P.74)

Eco drive mode indicator

*2, 4

VSC OFF indicator

(P.425)

(P.422)

*2, 4

Sport mode indicator

(P.422)

PCS warning light

(P.293)

Driving assist information

*2, 4

Custom mode indicator

(P.422)

indicator

(P.354,

3

360, 374, 379, 384)

BSM outside rear view

*4, 5

“PASSENGER AIR

BAG” indicator

*4, 6

mirror indicators

(if

lights

(P.44)

equipped) (P.354)

Brake hold standby indica-

*4

REC indicator (if

equipped) (P.352)

tor (P.266)

Brake hold operated indi-

*4

*1

:This light illuminates on the

multi-information display with a

message.

cator (P.266)

*2

*3

*6

:The light comes on when the

system is turned off.

Security indicator

(P.70)

Charging cable indicator

:Intuitive parking assist OFF indi-

cator turns on when the power

switch is turned to ON while the

Intuitive parking assist function is

on. It will turn off after a few sec-

onds.

(P.118)

“READY” indicator

(P.251)

Low outside temperature

*7

*4

indicator (P.159)

:These lights turn on when the

power switch is turned to ON to

indicate that a system check is

being performed. They will turn

off after the hybrid system is on,

or after a few seconds. There

may be a malfunction in a sys-

tem if the lights do not turn on, or

turn off. Have the vehicle

EV indicator (P.78)

Parking brake indicator

(P.263)

(U.S.A.)

Parking brake indicator

(P.263)

inspected by your Toyota dealer.

(Canada)

*5

*8

:This light illuminates on the out-

side rear view mirrors.

EV drive mode indicator

(P.73)

154

3-1. Instrument cluster

*6

:This light illuminates on the over-

head console panel.

*7

:When the outside temperature is

approximately 37°F (3°C) or

lower, the indicator will flash for

approximately 10 seconds, then

stay on.

*8

*9

:The displayed indicator changes

according to the current plug-in

hybrid system operation mode.

:For Puerto Rico

*10

: Except for Puerto Rico

■BSM (Blind Spot Monitor) out-

side rear view mirror indicators

(if equipped)

In order to confirm operation, the

BSM outside rear view mirror indica-

tors illuminate in the turning the

BSM function/RCTA function on

(P.354, 373).

If the system is functioning correctly,

the BSM outside rear view mirror

indicators will turn off after a few

seconds.

If the BSM outside rear view mirror

indicators do not illuminate or do not

turn off, there may be a malfunction

in the system. If this occurs, have

the vehicle inspected by your

Toyota dealer.

155

3-1. Instrument cluster

Gauges and m eters

The meters display various drive information.

Meter display

 Main meter in center position

3

The units used on the meter and display may differ depending on the target

region.

A

Outside temperature (P.159)

B

Hybrid System Indicator

Displays hybrid system output or regeneration level. (P.158)

C

Shift position indicator

Displays the selected shift position. (P.256)

D

Clock

The GPS clock’s time is automatically adjusted by utilizing GPS time infor-

mation. For details, refer to the “MULTIMEDIA OWNER’S MANUAL”.

E

Fuel gauge

Displays the quantity of fuel remaining in the tank.

F

EV driving range/EV energy remaining

The content can be switched through a customized setting. (P.166)

EV driving range:

Displays the EV driving range with charge remaining in the hybrid battery

(traction battery). (P.159)

156

3-1. Instrument cluster

EV energy remaining:

Displays the amount of charge remaining in the traction battery. (P.158)

G

Distance to empty

Displays driving range with remaining fuel. (P.158)

H

Speedometer

Displays the vehicle speed.

I

SOC (State of Charge) gauge

Displays the amount of charge remaining in the traction battery. (P.158)

J

Odometer, trip meter and oil maintenance

Odometer:

Displays the total distance that the vehicle has been driven.

Trip meter:

Displays the distance the vehicle has been driven since the meter was last

reset. Trip meters “A” and “B” can be used to record and display different

distances independently.

Oil maintenance:

Displays the distance until the next engine oil change.

 Main meter moved to the right

The units used on the meter and display may differ depending on the target

region.

A

Outside temperature (P.159)

B

Multi-information display

Presents the driver with a variety of driving-related data. (P.161)

Displays warning messages if a malfunction occurs. (P.566)

C

Hybrid System Indicator

157

3-1. Instrument cluster

Displays hybrid system output or regeneration level. (P.158)

D

Clock

The GPS clock’s time is automatically adjusted by utilizing GPS time infor-

mation. For details, refer to the “MULTIMEDIA OWNER’S MANUAL”.

E

Shift position indicator

Displays the selected shift position (P.256)

F

Fuel gauge

Displays the quantity of fuel remaining in the tank.

G

EV driving range/EV energy remaining

The content can be switched through a customized setting. (P.166)

EV driving range:

3

Displays the EV driving range with charge remaining in the hybrid battery

(traction battery). (P.159)

EV energy remaining:

Displays the amount of charge remaining in the traction battery. (P.158)

H

Distance to empty

Displays driving range with remaining fuel. (P.158)

I

Speedometer

Displays the vehicle speed.

J

SOC (State of Charge) gauge

Displays the amount of charge remaining in the traction battery. (P.158)

K

Odometer, trip meter and oil maintenance

Odometer:

Displays the total distance that the vehicle has been driven.

Trip meter:

Displays the distance the vehicle has been driven since the meter was last

reset. Trip meters “A” and “B” can be used to record and display different

distances independently.

Oil maintenance:

Displays the distance until the next engine oil change.

■The meters and display illumi-

nate when

The power switch is in ON.

158

3-1. Instrument cluster

■Hybrid System Indicator

In the following situation, the Hybrid

System Indicator does not operate.

A

Charge area

*

●“READY” indicator is not illumi-

nated.

Shows regeneration status. Regen-

erated energy will be used to charge

the hybrid battery (traction battery).

●The shift position is in a position

other than D or B.

B

Eco area

■SOC (State of Charge) gauge

Shows that the vehicle is being

driven in an Eco-friendly manner.

Displays the current amount of

charge remaining in the traction bat-

tery.

By keeping the indicator needle

within Eco area, more Eco-friendly

driving can be achieved.

●The remaining battery for EV driv-

ing in EV mode is displayed in

green, and the remaining battery

used in HV mode is displayed in

blue.

C

Power area

Shows that an Eco-friendly driving

range is being exceeded (during full

power driving etc.)

●The amount of the remaining bat-

tery displayed decrease as the

vehicle is driven and increase

when the hybrid battery (traction

battery) is charged, electrical

energy is regenerated using the

regenerative braking (P.78) or

electricity is generated by the gas-

oline engine.

D

Hybrid Eco area (HV mode)

Shows that gasoline engine power

is not being used very often.

The gasoline engine will automati-

cally stop and restart under various

conditions.

●If the remaining battery is not dis-

played in green, HV mode is auto-

matically selected and EV mode

cannot be used. To enable EV

driving, charge the hybrid battery

(traction battery). (P.94)

E

EV driving area (EV mode or

AUTO EV/HV mode)

Shows that the vehicle is driven

using only the electric motor (trac-

tion motor).

*

: When used in this manual, “regen-

eration” refers to the conversion of

energy created by the movement

of the vehicle into electrical

energy.

159

3-1. Instrument cluster

■Outside temperature display

A

B

The hybrid battery (traction bat-

tery) is fully charged

●Displays the outside temperature

within the range of -40°F (-40°C)

to 140°F (60°C).

The hybrid battery (traction bat-

tery) for EV mode is not remain-

ing

●When the outside temperature is

approximately 37°F (3°C) or

3

lower, the indicator

will flash

■Distance to empty

for approximately 10 seconds,

then stay on.

●This distance is computed based

on your average fuel consump-

tion. As a result, the actual dis-

tance that can be driven may

differ from that displayed.

●In the following situations, the cor-

rect outside temperature may not

be displayed, or the display may

take longer than normal to

change.

• When stopped, or driving at low

speeds (less than 12 mph [20

km/h])

• When the outside temperature

has changed suddenly (at the

entrance/exit of a garage, tunnel,

etc.)

●When only a small amount of fuel

is added to the tank, the display

may not be updated. When refuel-

ing, turn the power switch off. If

the vehicle is refueled without

turning the power switch off, the

display may not be updated.

●When “Refuel” is displayed, the

remaining fuel amount is low and

the distance that can be driven

with the remaining fuel cannot be

calculated. Refuel immediately.

●When “--” or “E” is displayed, the

system may be malfunctioning.

Take your vehicle to your Toyota

dealer.

■EV driving range

■Liquid crystal display

●When the air conditioning system

Small spots or light spots may

appear on the display. This phe-

nomenon is characteristic of liquid

crystal displays, and there is no

problem continuing to use the dis-

play.

is operating,

is displayed next

to the EV driving range and the

EV driving range with the air con-

ditioning system on is displayed.

●The EV driving range may shorten

even when not driving due to

power consumption by the sys-

tem.

■Open Source Software Informa-

tion

ited.

●For details, refer to “EV driving

range” (P.90)

Licensed under the Apache

License, Version 2.0 (the “License”);

you may not use this file except in

160

3-1. Instrument cluster

compliance with the License.

You may obtain a copy of the

License at

http://www.apache.org/licenses/

LICENSE-2.0

Unless required by applicable law or

agreed to in writing, software distrib-

uted under the License is distributed

on an “AS IS” BASIS, WITHOUT

WARRANTIES OR CONDITIONS

OF ANY KIND, either express or

implied. See the License for the

specific language governing permis-

sions and limitations under the

License.

Using the “ODO TRIP”

switch

Switches the items of the odom-

eter, trip meter A, trip meter B

WARNING

■The information display at

low temperatures

and

(oil maintenance) by

pressing the “ODO TRIP”

switch.

Allow the interior of the vehicle to

warm up before using the liquid

crystal information display. At

extremely low temperatures, the

display monitor may respond

slowly, and display changes may

be delayed.

When the trip meter is dis-

played, pressing and holding the

switch will reset the trip meter.

NOTICE

■To prevent damage to the

engine and its components

The engine may be overheating if

“Engine Coolant Temp High Stop

in a Safe Place See Owner’s

Manual” is shown on the multi-

information display. In this case,

immediately stop the vehicle in a

safe place, and check the engine

after it has cooled completely.

(P.594)

■ Pop-up display

Distance until the next engine oil

change will be displayed when a

warning message indicating that

oil maintenance is required or

should be performed soon is

displayed.

Switching the meter dis-

play

The multi-information display

can be switched between dis-

play and hidden.

161

3-1. Instrument cluster

Adjusting meter bright-

ness

Multi-information dis-

play

The meter brightness can be

adjusted.

The multi-information dis-

play is used to display fuel

efficiency related informa-

tion and various types of

driving-related information.

The multi-information dis-

play can also be used to

change the display settings

and other settings.

3

1 Darker

Display contents

2 Brighter

Following information is dis-

played on the multi-information

display.

■Brightness of the meter lights

(day mode and night mode)

The brightness of the meter lights

can be adjusted individually.

In the following situations, the

meters changes between day mode

and night mode.

●Day mode: When the tail lights are

off or when the tail lights are on

but the surrounding area is bright

●Night mode: When the tail lights

are on and the surrounding area is

dark

A

Menu icons (P.162)

B

Information display area

A variety of information can be dis-

played by selecting a menu icon.

Additionally, warning or sugges-

tion/advice pop-up displays will be

displayed in some situations.

C

RSA (Road Sign Assist) dis-

play area (if equipped)

Displays recognized signs while the

RSA (Road Sign Assist) is operat-

ing. (P.329)

162

3-1. Instrument cluster

hands-free system, refer to “MUL-

TIMEDIA OWNER’S MANUAL”.

D

Driving support system infor-

mation (P.165)

WARNING

■The multi-information display is

displayed when

■Caution for use while driving

For safety, avoid operating the

meter control switch while driving

as much as possible, and do not

look continuously at the multi-

information display while driving.

Stop the vehicle and operate the

meter control switch. Failure to do

so may cause a steering wheel

operation error, resulting in an

unexpected accident.

The power switch is in ON.

■Liquid crystal display

(P.159)

Changing the display

The multi-information display is

operated using the meter control

switches.

Menu icons

Information related to each icon

can be displayed by selecting

the icon with the meter control

switches.

Some of the information may be

displayed automatically depending

on the situation.

Icon

Display

A

/

: Select menu icons,

scroll the screen and move

the cursor

Driving information dis-

play (P.163)

/

: Change displayed

Driving support system

information display

(P.165)

content, scroll the screen and

move the cursor

B

Press: Enter/Set

Audio system-linked dis-

Press and hold: Reset/Dis-

play customizable items

play (P.166)

Vehicle information dis-

C

D

Return to the previous

screen/Move the main meter

play (P.166)

Settings display

(P.166)

Call sending/receiving and

history display

Warning message dis-

play (P.172)

Linked with the hands-free system,

sending or receiving call is dis-

played. For details regarding the

163

3-1. Instrument cluster

.

Driving information dis-

play

*3

:Average power consumption

after starting is reset each time

the hybrid system stops.

Select to display power con-

sumption or fuel consumption

data in various forms.

 HV mode

■ Power Consumption/Fuel

Economy

The display contents are differ-

ent in EV mode or AUTO EV/HV

mode, and HV mode.

 EV mode or AUTO EV/HV

mode

3

A

Current fuel consumption

Displays the instantaneous current

fuel consumption.

B

Average fuel economy

Displays the average fuel economy

since the function was reset, the

average fuel economy after starting

*1, 2, 3

or refueling.

The average fuel economy selected

A

Current power consumption

by “Fuel Economy” on the

screen is displayed.

*1

Displays the instantaneous current

power consumption.

:Use the displayed fuel consump-

B

Average power consumption

tion as a reference only.

Displays the average power con-

sumption since the function was

reset or the average power con-

*2

:Average fuel economy after

starting is reset each time the

hybrid system stops.

*1, 2, 3

sumption after starting.

*3

The average power consumption

selected by “Power Consumption”

:Average fuel economy since the

function was reset can be reset

on the

*1

screen is displayed.

by pressing and holding

.

:Use the displayed power con-

sumption as a reference only.

■ ECO Accelerator Guid-

ance/“Eco Score”

*2

:Average power consumption

since the function was reset can

be reset by pressing and holding

Displays a reference operation

range for using the accelerator

pedal according to driving condi-

164

3-1. Instrument cluster

It is easier to drive in an Eco-

friendly manner by driving accord-

ing to the display showing the

accelerator pedal operations and

staying within the reference opera-

tion range.

tions, and a score result that

evaluates the current driving

status.

 “Eco Score”

The driving status for the following

3 situations are evaluated in 5 lev-

els: Smooth start-off acceleration

(“Start”), driving without sudden

acceleration (“Cruise”) and smooth

stopping (“Stop”). Each time the

vehicle is stopped, a score result is

displayed out of a perfect score of

100 points.

A

ECO Accelerator Guidance

B

“Eco Score”

 ECO Accelerator Guidance

A

Score result

A

ECO area

B

Eco start status

Shows that the vehicle is being

driven in an Eco-friendly manner.

C

Eco cruise status

B

Reference operation range

D

Eco stop status

A zone is displayed in blue under

the Eco area which can be used as

a reference operation range for

using the accelerator pedal accord-

ing to driving conditions such as

starting off and cruising.

3 situations are displayed with each

icon while driving.

How to read the bar display:

C

Current acceleration

The ECO Accelerator Guidance

display changes according to the

driving status, such as when start-

ing off or cruising.

165

3-1. Instrument cluster

■ Solar charging information

screen (if equipped)

P.173

■Electricity consumption

When the unit is set to “miles/kWh”:

Electricity consumption is the con-

sumption rate of the electricity when

EV driving is performed and equiva-

lent to the fuel consumption for the

gasoline vehicles. For this vehicle,

driven distance per kWh of electric-

ity consumed (“miles/kWh”) is dis-

played as electricity consumption on

each screen.

A

B

C

Not yet evaluated

Low

High

3

After the hybrid system is started,

the Eco score will not be displayed

until the vehicle speed exceeds

approximately 19 mph (30 km/h).

When the unit is set to “km/kWh” or

“kWh/100km”: Electricity consump-

tion is the consumption rate of the

electricity when EV driving is per-

formed and equivalent to the fuel

consumption for the gasoline vehi-

cles. For this vehicle, electricity con-

sumed per 100 km (“kWh/100km”)

or driven distance per kWh of elec-

tricity consumed (“km/kWh”) is dis-

played as electricity consumption on

each screen.

The Eco score will be reset each

time the hybrid system is started.

■ Elapsed time after start-

ing/EV Driving Ratio

■ECO Accelerator Guid-

ance/“Eco Score” will not oper-

ate when

The ECO Accelerator Guid-

ance/“Eco Score” will not operate in

the following situations:

●The Hybrid System Indicator is not

operating.

●The vehicle is being driven using

the dynamic radar cruise control.

A

EV driving ratio after starting

The percent traveled using only

electric motor power after starting

Driving support system

information display

*

the hybrid system is displayed.

B

Elapsed time after starting

Select to display the operational

status of the following systems:

Displays the elapsed time since

*

hybrid system start.

*

 LTA (Lane Tracing Assist)

(P.305)

: It is reset each time the hybrid

system stops.

 LCA (Lane Change Assist) (if

166

3-1. Instrument cluster

equipped) (P.310)

A

B

Drive information type

Drive information items

 LDA (Lane Departure Alert)

(P.313)

Displays the following depend-

ing on which drive information

type and drive information items

 PDA (Proactive driving assist)

(P.320)

 Dynamic radar cruise control

(P.331)

were selected in

. (P.170)

 After start

 Cruise Control (P.342)

• Distance: Displays the distance

driven since hybrid system start

■ Navigation system-linked

display (if equipped)

• Elapsed time: Displays the

elapsed time since hybrid system

start

Select to display the following

navigation system-linked infor-

mation.

• Average vehicle speed: Displays

the average vehicle speed since

hybrid system start

 Route guidance to destination

 Compass

 After reset

• Distance: Displays the distance

driven since the display was

Audio system-linked dis-

play

*

reset

• Elapsed time: Displays the

elapsed time since the display

Select to enable selection of an

audio source or track on the dis-

play.

*

was reset

• Average vehicle speed: Displays

the average vehicle speed since

Vehicle information dis-

play

*

the display was reset

*

: To reset, display the desired item

■ Drive information

and press and hold the

control switch.

meter

Displays drive information such as

the following:

■ Energy monitor

P.173

■ Tire pressure

P.516

Settings display

Vehicle settings and the content

167

3-1. Instrument cluster

displayed on the screen can be

changed by using the meter

control switches.

 “Alert Timing”

Select to set the alert timing.

■

BSM (Blind Spot Moni-

tor) (if equipped) (P.354)

■ Setting procedure

1 Operate

or

meter control switches and

of the

Select to set up the following

items.

select

.

 BSM (Blind Spot Monitor)

on/off

2 Operate

or

of the

meter control switches and

select the desired item.

Select to enable/disable the BSM

system.

• If the function is turned on and

off or the volume, etc. is

changed on the setting

 “Support timing”

3

Select to change the alert timing for

an approaching vehicle.

screen, the setting is changed

 “Brightness”

each time

is pressed.

Select to switch the brightness of

the outside rear view mirror indica-

tors. (P.354)

• For functions that allow oper-

ation contents, display con-

tents, etc., of function to be

selected, the setting screen is

displayed by pressing and

 “Buzzer alert”

Select to enable/disable the buzzer

alert which sounds when BSM sys-

tem is operated.

holding

. When the setting

screen is displayed, select the

setting or desired value (time,

■

PCS (Pre-Collision Sys-

tem) (P.293)

etc.) with

.

Select to set up the following

items.

3 After changing the settings,

press

switches.

of the meter control

 PCS on/off

Select to enable/disable the pre-

collision system.

■

LDA (Lane Departure

Alert) (P.313)

 “Warning timing”

Select to set up the following

items.

Select to change the pre-collision

warning timing.

 Lane Departure Alert on/off

■

PDA (Proactive driving

assist) (P.320)

Select to enable/disable Lane

Departure Alert system.

 PDA on/off

 “Alert Options”

Select to enable/disable the PDA

Select to set the alert type.

168

3-1. Instrument cluster

system.

 Volume

 “Sensitivity”

Select to set the volume of the

buzzer which sounds when the

RCTA, the RCD (if equipped) or the

intuitive parking assist is operated.

Select to change the alert timing for

a detected object.

 SA (Steering Assist)

■

RCD (Rear Camera

Detection) function (if

equipped) (P.378)

Select to enable/disable the Steer-

ing Assist function.

 DA (Deceleration Assist)

Select to enable/disable the

Rear Camera Detection func-

tion.

Select to enable/disable the Decel-

eration Assist function.

 OAA (Obstacle Anticipation

Assist)

■

PKSB (Parking Sup-

port Brake System) (if

equipped) (P.382)

Select to enable/disable the Obsta-

cle Anticipation Assist function.

Select to enable/disable the

Parking Support Brake function.

■

Intuitive parking

assist (P.363)

■

SEA (Safe Exit Assist) (if

equipped) (P.359)

Select to set up the following

items.

Select to set up the following

items.

 Intuitive parking assist on/off

Select to enable/disable the intui-

tive parking assist.

 Safe Exit Assist on/off

 Volume

Select to enable/disable the Safe

Exit Assist system.

Select to set the volume of the

buzzer which sounds when the

RCTA (if equipped), the RCD (if

equipped) or intuitive parking assist

is operated.

 “Sensitivity”

Select to change the alert timing for

a vehicle or bicycle.

 Mirror indicate on/off

■

RCTA (Rear Cross Traf-

fic Alert) (if equipped)

(P.373)

Select to enable/disable the outside

rear view mirrors display.

■

RSA (Road Sign

Assist) (if equipped)

(P.329)

Select to set up the following

items.

 RCTA (Rear Cross Traffic

Alert) on/off

Select to set up the following

items.

Select to enable/disable the RCTA

system.

 Road Sign Assist on/off

169

3-1. Instrument cluster

Select to enable/disable the RSA

(Road Sign Assist).

charging schedule. (P.123)

• “Charging Current”

 “Notification Method”

Select to change the charging cur-

rent. (P.119)

Select to change each notification

method used to notify the driver

when the system recognizes

excess speed and Do Not Enter

sign.

• “Connector Lock”

Select to change the method for

locking and unlocking. (P.103)

• “Battery Cooler”

 “Notification Level”

Select to enable/disable the bat-

tery cooler. (P.109)

Select to change each notification

level used to notify the driver when

the system recognizes excess

speed.

• “Battery Heater”

Select to enable/disable the bat-

tery heater. (P.108)

3

■

DRCC (P.331)

 Driver Break Suggestion

(P.316)

Select to set up the following

items.

Select to enable/disable the drive

break suggestion.

 “Extended Resume Time” (if

equipped)

 “TrafficJamAsst” (if equipped)

Select to enable/disable the

extended resume time function.

(P.333)

Select to enable/disable the Traffic

Jam Assist Function. (P.348)

 “DMC Recording” (if

equipped)

 “Acceleration Setting”

Select to change the setting for

when vehicle accelerates until the

set vehicle speed is reached.

Select to enable/disable the notifi-

cation for driver monitor camera

recording when the operation of

Traffic Jam Assist is started.

(P.348)

 “Guide message”

Select to enable/disable the guide

message display.

 LCA (Lane Change Assist) (if

equipped) (P.310)

 “Curve Speed Reduction”

Select to change the curve speed

reduction function setting.

(P.338)

Select to enable/disable Lane

Change Assist system.

 FCTA (Front Cross Traffic

Alert) (if equipped) (P.326)

■

Vehicle Settings

Select to set up the following items.

 “Charging Settings”

• FCTA on/off

Select to set up the following items.

• “Charging Schedule”

Select to enable/disable the FCTA

system.

Select to register or change the

170

3-1. Instrument cluster

• “Timing”

Select to set up the following items.

• System settings

Select to set the alert timing for

FCTA system.

Select to enable/disable the power

back door system.

 Regenerative brake

Select to set up the following items.

• “Deceleration”

• “Opening Adjustment”

Select the open position when

power back door is fully open.

Select to change the regenerative

braking force when Regeneration

Boost is operating. (P.260)

• “Volume”

Select to set the volume of the

buzzer which sounds when the

power back door system operates.

• “Deceleration Memory”

Select to store the settings for

regenerative braking force.

(P.260)

 “Scheduled Maintenance”

Select to reset the scheduled main-

tenance information (message indi-

cating maintenance is required and

distance until the next mainte-

nance) after all maintenance is per-

formed.

 “TPWS setting” (Tire Pres-

sure Warning System)

(P.516)

• “Tire Set Switching”

Select to register the tire pressure

warning system sensor ID code set.

(P.524)

 Oil Maintenance

Select to reset the Oil maintenance.

(P.506)

• “Tire Rotation”

 Rear Seat Reminder

(P.188)

Select to register the position of

each wheel after performing a tire

rotation. (P.518)

Select to enable/disable the rear

seat reminder function.

• “Tire Pressure Setting”

 Digital Keys (if equipped)

Select to perform the tire inflation

pressure setting procedure of the

tire pressure warning system.

(P.520)

Select to reset registered digital

keys. (P.183)

■

Settings

• “Pressure unit setting”

 “Language”

Select to change the units of mea-

sure displayed. (P.619)

Select to change the language on

the multi-information display.

 Driver monitor (if equipped)

 “Units”

Select to enable/disable the driver

monitor warning function. (P.292)

Select to change the unit of mea-

sure for fuel consumption.



PBD (Power Back Door)

(if equipped) (P.194)

 “Meter Type”

Select to enable/disable Hybrid

171

3-1. Instrument cluster

System Indicator. (P.158)

Select to set the items displayed

from “Drive Info” or “Charging

Schedule” when the power switch

is turned off.



EV indicator

Select to enable/disable the EV

indicator.

 Pop-Up Display

 EV Drive Information

Select to enable/disable the pop-up

displays, which may appear in

some situations.

Select to change the item on the

meter display between “EV Energy

remaining” or “EV Distance remain-

ing”. (P.155)

 “Calendar”

Select to set up the calender. This

can only be set if GPS calibration of

clock is turned off in the multimedia

system settings.



(Driving information dis-

play settings)

3

Select to set up the following items.

• “Hybrid System”

 Default Settings

Select to reset the meter display

settings.

Select to enable/disable the ECO

Accelerator Guidance (P.158).

• “Fuel Economy”

■Tire pressure

Select to change the display on

Fuel Economy. (P.163)

• It may take a few minutes to dis-

play the tire inflation pressure

after the power switch is turned to

ON. It may also take a few min-

utes to display the tire inflation

pressure after inflation pressure

has been adjusted.

• “Power Consumption”

Select to change the display on

Power Consumption. (P.163)



(Audio settings)

• “---” may be displayed if the tire

position information cannot be

determined due to unfavorable

radio wave conditions.

Select to enable/disable

screen.

• Tire inflation pressure changes

with temperature. The displayed

values may also be different from

the values measured using a tire

pressure gauge.



(Vehicle information dis-

play settings)

• “Drive Info Type”

Select to change the drive informa-

tion type display between trip and

total. (P.163)

■Suspension of the settings dis-

play

●In the following situations, opera-

tion of the settings display will be

temporarily suspended.

• “Drive Info Items”

• When a warning message

appears on the multi-information

display

Select to set the items on the upper

and lower side of the drive informa-

tion screen from three items, aver-

age speed, distance and total time.

• When the vehicle begins to move

●Settings for functions not

equipped to the vehicle are not

 “Trip Summary”

172

3-1. Instrument cluster

displayed.

■ Suggestion to enable the

power back door (if

equipped)

●When a function is turned off, the

related settings for that function

are not selectable.

If the power back door system is

WARNING

disabled (setting on

set to

off) and the power back door

switch on the instrument panel

is operated, a suggestion mes-

sage will be displayed asking if

you wish to enable the power

back door system. To enable

the power back door system,

select “Yes”.

■Cautions during setting up

the display

As the hybrid system needs to be

operating during setting up the

display, ensure that the vehicle is

parked in a place with adequate

ventilation. In a closed area such

as a garage, exhaust gases

including harmful carbon monox-

ide (CO) may collect and enter

the vehicle. This may lead to

After enabling the power back door

system, press the power back door

switch again to open or close the

power back door.

death or a serious health hazard.

NOTICE

■During setting up the display

■ Suggestion to turn off the

To prevent 12-volt battery dis-

charge, ensure that the hybrid

system is operating while setting

up the display features.

headlights

If the headlights are left on for a

certain amount of time after the

power switch has been turned

off, a suggestion message will

be displayed.

Warning message display

Select to display warning mes-

sages and measures to be

taken if a malfunction is

detected. (P.566)

When the headlight switch is in

the AUTO position: The mes-

sage asking if you wish to turn

the headlights off is displayed.

To turn the headlights off, select

“Yes”.

Suggestion function

Displays suggestions to the

driver in the following situations.

To select a response to a dis-

played suggestion, use the

meter control switches.

If the driver’s door is opened after

the power switch is turned off, this

suggestion message will not be dis-

played.

■Customization

The suggestion function can be

turned on/off. (Customizable fea-

tures: P.619)

173

3-1. Instrument cluster

■ Display procedure

Energy monitor/con-

sum ption sc reen/solar

charging information

 Multi-information display

Use the meter control switches,

display the energy monitor on

the multi-information display.

*

screen

*

: If equipped

For detail regarding the multi-infor-

mation display, refer to P.161.

You can view the status of

your hybrid system, fuel

consumption information

and information related to

the solar charging system

on the multi-information

display and Multimedia Dis-

play.

 Multimedia Display

Touch

on the main menu,

then touch “Energy flow” on the

sub menu.

3

For detail regarding the Multimedia

Display, refer to “MULTIMEDIA

OWNER’S MANUAL”.

■ Reading the display

System components

The arrows will appear in accor-

dance with the energy flow.

When there is no energy flow,

arrows will not be displayed.

The color of the arrows will change

as follows

Blue: When the hybrid battery (trac-

tion battery) is regenerated or

charged.

A

B

C

Multi-information display

Multimedia Display

Orange: When the hybrid battery

(traction battery) is in use.

Red: When the gasoline engine is

in use.

Meter control switches

 Multi-information display

Energy monitor

The energy monitor can be used

to check the vehicle drive status,

hybrid system operation status

and energy regeneration status.

174

3-1. Instrument cluster

The image shows all the arrows as

an example. The actual display will

vary depending on conditions.

■Hybrid battery (traction battery)

status

It will be green when the hybrid bat-

tery (traction battery) is being

charged, and yellow when the

hybrid battery (traction battery) is

being used.

A

Gasoline engine

B

Tires

C

Hybrid battery (traction bat-

tery)

■Remaining charge amount

warning of hybrid battery (trac-

tion battery)

 Multimedia Display

●The buzzer sounds intermittently

when the hybrid battery (traction

battery) remains without charging

while the shift position is in N, or

the remaining charge amount

drops below a certain level. If the

remaining charge amount drops

further, the buzzer sounds contin-

uously.

●When a warning message is

shown on the multi-information

display and the buzzer sounds,

follow the instructions displayed

on the screen to perform trouble-

shooting.

The image shows all the arrows as

an example. The actual display will

vary depending on conditions.

■Color of the gasoline engine on

the Multimedia Display

A

Gasoline engine

B

Electric motor (traction

motor)

It will be blue when the engine is

warming up, and it will turn to red

when the warming up is finished.

C

Solar panel (solar roof) (if

equipped)

Consumption screen

D

Hybrid battery (traction bat-

tery)

For detail regarding the Multi-

media Display, refer to “MULTI-

MEDIA OWNER’S MANUAL”.

Charging connector^*1

E

Power outlet^*2

F

■ Display procedure

G

Tires

Touch

on the main menu,

*1

then touch “Trip information” on

the sub menu.

:The energy flow is displayed

while charging. (P.116)

*2

:The energy flow is displayed

when the accessory power outlet

can be used.

■ Current fuel consumption

screen

If a screen other than current

fuel consumption screen is dis-

175

3-1. Instrument cluster

played, touch “Current”.

Use the displayed average fuel

consumption as a reference.

The image is an example only, and

may vary slightly from actual condi-

tions.

A

B

Latest fuel consumption

Best recorded fuel consump-

tion

3

C

Previous fuel consumption

record

D

E

Resetting the history data

A

Resetting the consumption

data

Updating the latest fuel con-

sumption data

B

Fuel consumption in the past

15 minutes

■Updating the history data

C

Current fuel consumption

Update the latest fuel consumption

by touching “Update” to measure

the current fuel consumption again.

D

Average vehicle speed since

the hybrid system was

started.

■Resetting the data

The fuel consumption data can be

deleted by touching “Clear data”.

E

Trip range

■Using the voice control system

F

Elapsed time since the hybrid

system was started.

Fuel consumption, trip range, etc.

can be checked using the voice con-

trol system.

■ History screen

For details regarding the voice con-

trol system, refer to “MULTIMEDIA

OWNER’S MANUAL”.

If a screen other than history

screen is displayed, touch “His-

tory”.

■Trip range

Use the displayed average fuel

consumption as a reference.

Displays the estimated maximum

distance that can be driven with the

quantity of fuel remaining.

The image is an example only, and

may vary slightly from actual condi-

tions.

This distance is computed based on

your average fuel consumption.

As a result, the actual distance that

can be driven may differ from that

displayed.

176

3-1. Instrument cluster

B

Mileage with power genera-

tion^*

Solar charging informa-

tion screen (vehicles with

solar charging system)

*

: Mileage with power generation

from the end of the previous drive

to the current state. These values

are calculated by converting the

power generated into driving dis-

tance, and may differ from the

actual driving distance. When

optional tires are installed, the

displayed value may differ from

the actual driving distance.

Information related to the solar

charging system can be dis-

played.

■ Display procedure

 Multi-information display

Solar charging information

screen can be displayed on

■ Energy screen (Multimedia

Display)

of the multi-information

display.

If a screen other than the energy

screen is displayed, touch

“Energy”.

For detail regarding the multi-

information display, refer to

P.161.

The image is an example only,

and may vary slightly from

actual conditions.

 Multimedia Display

Touch

on the main menu,

then touch “Solar” on the sub

menu.

For detail regarding the Multimedia

Display, refer to “MULTIMEDIA

OWNER’S MANUAL”.

■ Solar charging information

screen (multi-information

display)

A

Current power generation

B

Today’s power generation

C

Total power generation

D

Clear data

Resets the daily data.

Daily power generation^*

E

*

: It may be reset by certain opera-

tions.

A

Current power generation

177

3-1. Instrument cluster

■ Distance screen (Multime-

dia Display)

If a screen other than the dis-

tance screen is displayed, touch

“Distance”.

The image is an example only,

and may vary slightly from

actual conditions.

3

A

Current power generation

B

Mileage with today’s power

generation^*1

C

Mileage with total power gen-

eration^*1

D

Clear data

Resets the daily data.

E

Mileage with daily power

generation^{*1, 2}

*1

:These values are calculated by

converting the power generated

into driving distance, and may

differ from the actual driving dis-

tance. When optional tires are

installed, the displayed value

may differ from the actual driving

distance.

*2

:It may be reset by certain opera-

tions.

178

3-1. Instrument cluster

Vehiclestatusinformationandindicators for Your Toyota Prius 4 Door Fifth Generation (2023-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals