Get Seats, Seat belts, Steering wheel and Mirrors Guide for Toyota Rav4 SUV Second Generation (2001-2005)

’03 Rav4_U (L/O 0208)

SECTION 1− 3

OPERATION OF INSTRUMENTS AND

CONTROLS

Seats, Seat belts, Steering wheel and Mirrors

Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Front seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Flattening seatbacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

SRS driver airbag and front passenger airbag . . . . . . . . . . . . . . . . . . . 52

Child restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Tilt steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Outside rear view mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Anti−glare inside rear view mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

29

’03 Rav4_U (L/O 0208)

Front seats—

—Seat adjustment precautions

Seats

While the vehicle is being driven, all ve-

hicle occupants should have the seatback

upright, sit well back in the seat and prop-

erly wear the seat belts provided.

Adjust the driver’s seat so that the foot

pedals, steering wheel and instrument

panel controls are within easy reach of

the driver.

D While adjusting the seat, do not put

your hands under the seat or near

the moving parts. Otherwise you

may catch and injure your hands or

fingers.

CAUTION

D Do not drive the vehicle unless the

occupants are properly seated. Do

D Adjustments should not be made

while the vehicle is moving, as the

seat may unexpectedly move and

cause the driver to lose control of

the vehicle.

not allow sitting on top of

a

folded−down seatback, or in the

luggage compartment or cargo area.

Persons not properly seated and/or

properly restrained by seat belts

can be severely injured in the event

of emergency braking or a collision.

D When adjusting the seat, be careful

that the seat does not hit a passen-

ger or luggage.

D After adjusting the seat position,

try sliding it forward and backward

to make sure it is locked in posi-

tion.

D During driving, do not allow pas-

sengers to stand up or move

around between seats. Severe inju-

ries can occur in the event of emer-

gency braking or a collision.

D After adjusting the seatback, push

back your body to make sure it is

locked in position.

D Do not put objects under the seats.

Otherwise, the objects may interfere

with the seat−lock mechanism or

unexpectedly push up the seat posi-

tion adjusting lever and the seat

may suddenly move, causing the

driver to lose control of the vehicle.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

30

’03 Rav4_U (L/O 0208)

—Adjusting front seats

1. SEAT POSITION ADJUSTING LEVER

CAUTION

Hold the center of the lever and pull it

up. Then slide the seat to the desired

position with slight body pressure and

release the lever.

To reduce the risk of sliding under

the lap belt during a collision, avoid

reclining the seatback any more than

needed. The seat belts provide maxi-

mum protection in a frontal or rear

collision when the driver and the pas-

senger are sitting up straight and

well back in the seats. If you are

reclined, the lap belt may slide past

your hips and apply restraint forces

directly to the abdomen. In the event

of a frontal collision, the more the

seat is reclined, the greater the risk

of personal injury.

2. SEAT CUSHION ANGLE ADJUSTING

KNOB

Turn the knob either way.

3. SEATBACK

LEVER

ANGLE

ADJUSTING

Lean forward and pull the lever up.

Then lean back to the desired angle

and release the lever.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

31

’03 Rav4_U (L/O 0208)

Rear seats—

—Rear seat precautions

—Adjusting rear seats

D When returning seats to their origi-

CAUTION

nal position, observe the following

precautions in order to prevent per-

sonal injury in a collision or sud-

den stop:

D Adjustment should not be made

while the vehicle is moving.

D When adjusting the seat, be careful

that the seat does not hit a passen-

ger or luggage.

Make sure the seat is securely

locked by pushing forward and rear-

ward on the top of the seatback or

by trying to pull up the edge of the

bottom cushion. Failure to do so

will prevent the seat belt from oper-

ating properly.

D Adjust both seat cushions to the

same position and align both seat-

backs at the same angle when a

person sits in the rear center posi-

tion. Otherwise, the person cannot

wear the seat belt properly and this

may cause serious injuries in a col-

lision.

Make sure the seat belts are not

twisted or caught under the seat

and are arranged in their proper

position and are ready to use.

D After adjusting the seat position,

try sliding it forward and backward

to make sure it is lock in position.

Folding the seats up will enlarge the lug-

gage compartment. See “Luggage stowage

precautions” on page 164 in Section 2 for

precautions in loading luggage.

D After adjusting the seatback, push

back your body to make sure it is

locked in position.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

32

’03 Rav4_U (L/O 0208)

1. SEAT POSITION ADJUSTING LEVER

NOTICE

D Adjust both seat cushions to the

Hold the center of the lever and pull it

up. Then slide the seat to the desired

position with slight body pressure and

release the lever.

same position and align both seat-

backs at the same angle when a

person sits in the rear center posi-

tion. Otherwise, the person cannot

wear the seat belt properly and this

may cause serious injuries in a col-

lision.

Do not fold the seatback forward

while the luggage cover is set.

When a person sits in the rear center

position, adjust both seat cushions to

the same position.

Do not place anything under the seats. It

might interfere with the seat−lock mecha-

nism.

D To reduce the risk of sliding under

the lap belt during

a

collision,

avoid reclining the seatback any

more than needed. The seat belts

2. SEATBACK

STRAP

ANGLE

ADJUSTING

provide maximum protection in

a

frontal or rear collision when the

passengers are sitting up straight

and well back in the seats. If you

are reclined, the lap belt may slide

past your hips and apply restraint

forces directly to the abdomen. In

the event of a frontal collision, the

more the seat is reclined, the great-

er the risk of personal injury.

Pull the strap up. Then lean back to the

desired angle and release the strap.

When a person sits in the rear center

position, align both seatbacks at the

same angle.

CAUTION

D Adjustments should not be made

while the vehicle is moving.

D After adjusting the seatback, push

back your body to make sure it is

locked in position.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

33

’03 Rav4_U (L/O 0208)

—Folding up rear seats

BEFORE FOLDING UP REAR SEAT

2. Insert the round end tab into the

FOLDING UP REAR SEATS

cover. You will hear a click when the

tabs are locked in the seat belt cov-

er. Make sure the tabs are securely

locked in the cover.

Stow the rear center seat belt, do the

following:

1. Hold the center of the lever and pull

it up. Then slide the front seat fully

forward.

1. Pull the seat belt out of its cover a

little and insert the concave end tab

into the higher slot of the cover.

Folding up the rear seats will enlarge the

luggage compartment. See “Luggage stow-

age precautions” on page 164 in Section

2 for precautions in loading luggage.

NOTICE

The seat belt must be stowed before

you fold the seatback.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

34

’03 Rav4_U (L/O 0208)

2. Hold the center of the lever and pull

it up. Then slide the rear seat fully

backward and pull it forward slightly

till it locks.

3. Lower the head restraint to the low-

4. Pull up the seat cushion lock release

lever and swing the whole seat up

and forward.

est position. Pull up the strap to

unlock the seatback and fold the

seatback forward until it locks.

NOTICE

Do not fold the seatback forward

while the luggage cover is set.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

35

’03 Rav4_U (L/O 0208)

5. Make sure the front legs are locked

and the seat is securely locked in

position.

RETURNING REAR SEATS

2. Pull the seatback lock release strap

and swing the seatback up.

1. To unlock the seat, hold the upper

back of the seat with your hand and

pull the lock release strap up. Swing

the whole seat down and set the

rear legs to the hooks on the floor.

Make sure the rear legs are securely

set to the hooks by trying to pull up

the rear part of the seat.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

36

’03 Rav4_U (L/O 0208)

—Removing rear seats

CAUTION

When returning seats to their original

position, observe the following pre-

cautions in order to prevent personal

injury in a collision or sudden stop:

D Make sure the seat is securely

locked by pushing forward and rear-

ward on the top of the seatback or

by trying to pull up the edge of the

bottom cushion. Failure to do so

will prevent the seat belt from oper-

ating properly.

1. Fold up rear seats. (See “—Folding

up rear seats” on page 34 in this

section for instructions.)

2. Unlock the seat by pulling the lock

release lever. Pull the seat toward

you slightly and lift.

D Make sure the seat belts are not

twisted or caught under the seat

and are arranged in their proper

position and are ready to use.

Removing the rear seats will enlarge the

luggage compartment. See “Luggage stow-

age precautions” on page 164 in Section

2 for precautions in loading luggage.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

37

’03 Rav4_U (L/O 0208)

—Reinstalling rear seats

CAUTION

When removing the seat, observe the

following precautions in order to pre-

vent personal injury:

D Be careful not to get your hands or

feet pinched in the seat.

D Be careful not to hit the removed

seat against a person or drop it on

yourself.

NOTICE

1. While pulling up the lock release le-

ver, place the rear hinge into the

rear hook on the floor.

2. Push the seat forward until it locks.

Avoid putting heavy loads on the re-

moved seat. The metallic tips of the

seat leg may be damaged and the

seat cannot be reinstalled.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

38

’03 Rav4_U (L/O 0208)

CAUTION

When returning seats to their original

position, observe the following pre-

cautions in order to prevent personal

injury in a collision or sudden stop:

D Make sure the seat is securely

locked by pushing forward and rear-

ward on the top of the seatback or

by trying to pull up the edge of the

bottom cushion. Failure to do so

will prevent the seat belt from oper-

ating properly.

3. To unlock the seat, hold the upper

back of the seat with your hand and

pull the lock release strap up. Swing

the whole seat down and set the

rear legs to the hooks on the floor.

Make sure the rear legs are securely

set to the hooks by trying to pull up

the rear part of the seat.

4. Pull the seatback lock release strap

and swing the seatback up.

D Make sure the seat belts are not

twisted or caught under the seat

and are arranged in their proper

position and are ready to use.

When removing or reinstalling the

seat, observe the following precau-

tions in order to prevent personal in-

jury:

D Do not fold or remove the seat

while the vehicle is moving.

D Be careful not to get your hands or

feet pinched in the seat.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

39

’03 Rav4_U (L/O 0208)

Flattening seatbacks

(front seat only)

D Be careful not to hit the removed

seat against a person or drop it on

yourself.

D After folding or installing the seat,

push it forward and backward to

make sure it is locked in position.

To prevent personal injury in a colli-

sion or sudden stop:

D Do not sit on or place anything on

the folded seatback while driving.

D Do not leave the removed seat

loose in the vehicle.

For flattening seatbacks, do the follow-

ing:

2. Remove the head restraint. Hold the

center of the lever and pull it up.

Then slide the seat further forward

than the front−most lock position.

D Do not try to sit on or place any-

thing on the removed seat.

1. Hold the center of the lever and pull

it up. Then slide the rear seat fully

backward and pull it forward slightly

till it locks.

D When reinstalling the seat, be care-

ful not to hit the seat against you

or inside of the vehicle.

D Install each seat in the same posi-

tion from which it was removed.

Failure to do so will prevent rear

seat occupants from using seat

belts properly.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

40

’03 Rav4_U (L/O 0208)

Head restraints

CAUTION

D Do not allow passengers to ride on

the flattened seat while driving; use

the seat in the normal position.

D After returning the seat to its origi-

nal position, try pushing the seat

and seatback forward and rearward

to make sure it is secured in place.

Be certain to replace head restraint.

3. Pull the seatback angle adjusting le-

ver up to unlock and push down the

seatback.

For your safety and comfort, adjust the

head restraint before driving.

To raise: Pull it up.

When returning the seatback upright, be

careful not to make yourself hit by the

seatback which will bound with consid-

erable spring force.

To lower: Push it down while pressing the

lock release button.

The head restraint is most effective when

it is close to your head. Therefore, using

a cushion on the seatback is not recom-

mended.

After returning the seat to its original

position, be certain to replace the head

restraint.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

41

’03 Rav4_U (L/O 0208)

Seat belts—

—Seat belt precautions

Toyota strongly urges that the driver and

passengers in the vehicle be properly re-

strained at all times with the seat belts

provided. Failure to do so could increase

the chance of injury and/or the severity of

injury in accidents.

Do not allow the child to stand up or

kneel on either rear or front seats. An

unrestrained child could suffer serious in-

jury or death during emergency braking or

a collision. Also, do not let the child sit

on your lap. It does not provide sufficient

restraint.

CAUTION

D Adjust the center of the head re-

straint so that it is closest to the

top of your ears.

D After adjusting the head restraint,

make sure it is locked in position.

Child. Use a child restraint system ap-

propriate for the child until the child be-

comes large enough to properly wear the

vehicle’s seat belts. See “Child restraint”

on page 59 for details.

Pregnant woman. Toyota recommends the

use of a seat belt. Ask your doctor for

specific recommendations. The lap belt

should be worn securely and as low as

possible over the hips and not on the

waist.

D Do not drive with the head re-

straints removed.

If a child is too large for a child restraint

system, the child should sit in the rear

seat and must be restrained using the

vehicle’s seat belt. According to accident

statistics, the child is safer when properly

restrained in the rear seat than in the

front seat.

Injured person. Toyota recommends the

use of a seat belt. Depending on the inju-

ry, first check with your doctor for specific

recommendations.

If a child must sit in the front seat, the

seat belts should be worn properly. If an

accident occurs and seat belts are not

worn properly, the force of the rapid infla-

tion of the airbag may cause death or

serious injury to the child.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

42

’03 Rav4_U (L/O 0208)

—Front and rear seat belts

D Inspect the belt system periodically.

CAUTION

Check for cuts, fraying, and loose

parts. Damaged parts should be re-

placed. Do not disassemble or

modify the system.

Persons should ride in their seats

properly wearing their seat belts

whenever the vehicle is moving.

Otherwise, they are much more likely

to suffer serious bodily injury or

death in the event of sudden braking

or a collision.

D Keep the belts clean and dry. If

they need cleaning, use a mild soap

solution or lukewarm water. Never

use bleach, dye, or abrasive clean-

ers—they may severely weaken the

belts. (See “Cleaning the interior”

on page 209 in Section 5.)

When using the seat belts, observe

the following:

D Use the belt for only one person at

a time. Do not use a single belt for

two or more people—even children.

D Replace the belt assembly (includ-

ing bolts) if it has been used in a

severe impact. The entire assembly

should be replaced even if damage

is not obvious.

Adjust the seat as needed and sit up

straight and well back in the seat. To

fasten your belt, pull it out of the re-

tractor and insert the tab into the

buckle.

D Avoid reclining the seatbacks too

much. The seat belts provide maxi-

mum protection when the seatbacks

are in the upright position. (Refer

to the seat adjustment instructions.)

You will hear a click when the tab locks

into the buckle.

D Be careful not to damage the belt

webbing or hardware. Take care that

they do not get caught or pinched

in the seat or side doors.

The seat belt length automatically adjusts

to your size and the seat position.

The retractor will lock the belt during a

sudden stop or on impact. It also may

lock if you lean forward too quickly. A

slow, easy motion will allow the belt to

extend, and you can move around freely.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

43

’03 Rav4_U (L/O 0208)

If the seat belt cannot be pulled out of the

retractor, firmly pull the belt and release

it. You will then be able to smoothly pull

the belt out of the retractor.

CAUTION

Always make sure the shoulder belt

is positioned across the center of

your shoulder. The belt should be

kept away from your neck, but not

falling off your shoulder. Failure to

do so could reduce the amount of

protection in an accident and cause

serious injuries in a collision.

When a passenger’s shoulder belt is com-

pletely extended and is then retracted

even slightly, the belt is locked in that

position and cannot be extended. This fea-

ture is used to hold the child restraint

system securely. (For details, see “Child

restraint” on page 59 in this section.) To

free the belt again, fully retract the belt

and then pull the belt out once more.

Seat belts with an adjustable shoulder

anchor—

CAUTION

D After inserting the tab, make sure

the tab and buckle are locked and

that the belt is not twisted.

Adjust the shoulder anchor position to

your size.

To raise: Slide the anchor up.

To lower: Push in the lock release button

and slide the anchor down.

D Do not insert coins, clips, etc. in

the buckle as this may prevent you

from properly latching the tab and

buckle.

After adjustment, make sure the anchor is

locked in position.

D If the seat belt does not function

normally, immediately contact your

Toyota dealer. Do not use the seat

until the seat belt is fixed. It cannot

protect an adult occupant or your

child from injury.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

44

’03 Rav4_U (L/O 0208)

CAUTION

Take up

slack

D Both high−positioned lap belts and

loose−fitting belts could cause seri-

ous injuries due to sliding under

the lap belt during a collision or

other unintended result. Keep the

lap belt positioned as low on hips

as possible.

Too high

D For your safety, do not place the

shoulder belt under your arm.

Keep as low on

hips as possible

Adjust the position of the lap and

shoulder belts.

To release the belt, press the buckle−re-

lease button and allow the belt to re-

tract.

Position the lap belt as low as possible

on your hips—not on your waist, then ad-

just it to a snug fit by pulling the shoulder

portion upward through the latch plate.

If the belt does not retract smoothly, pull

it out and check for kinks or twists. Then

make sure it remains untwisted as it re-

tracts.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

45

’03 Rav4_U (L/O 0208)

CAUTION

Make sure the both buckles are cor-

rectly located and securely latched.

Failure to properly match the buckle

and tab may cause severe injury in

case of an accident or a collision.

SEAT BELT FOR REAR CENTER SEAT

Two buckles and tabs for rear center

seat belt

The rear center seat belt is a 3−point type

restraint with 2 buckles. Both seat belt

buckles must be correctly located and se-

curely latched for proper operation.

The 2 buckles for the rear center seat

belt are distinguished with colors of the

buckle release button. Also the

2

tabs

have different shape for its end so that

the belt is not buckled in the wrong place.

Make sure that buckle 1 (with light gray

buckle−release button) is securely latched

for ready use of the center seat belt.

Buckle

1

(with light gray buckle−re-

lease button)—Properly matches with

concave end tab

Buckle 2 (with red buckle−release but-

ton)—Properly matches with round end

tab

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

46

’03 Rav4_U (L/O 0208)

—Stowing the rear center seat

belt

To release the concave end tab, insert the

key into the hole on buckle 1 (with light

gray buckle−release button) and allow the

belt to retract.

STOWING THE REAR CENTER SEAT

BELT

CAUTION

1. To stow the rear center seat belt,

pull the seat belt out of its cover a

little and insert the concave end tab

into the higher slot of the cover.

Do not use the rear center seat belt

with either buckle released. Fastening

only the shoulder belt or lap belt may

cause severe personal injury in case

of sudden braking or a collision.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

47

’03 Rav4_U (L/O 0208)

—Seat belt extender

If your seat belts cannot be fastened se-

curely because they are not long enough,

a personalized seat belt extender is avail-

able from your Toyota dealer free of

charge.

Please contact your local Toyota dealer so

that the dealer can order the proper re-

quired length for the extender. Bring the

heaviest coat you expect to wear for prop-

er measurement and selection of length.

Additional ordering information is available

at your Toyota dealer.

2. Insert the round end tab into the

cover. You will hear a click when the

tabs are locked in the seat belt cov-

er. Make sure the tabs are securely

locked in the cover.

PULLING OUT THE REAR CENTER SEAT

BELT

To use the rear center seat belt, pull

the belt out a little and then pull the

tabs out from the cover.

Seat belt must be stowed before you fold

the seatback. (See “—Folding up rear

seats” on page 34 or “—Removing rear

seats” on page 37 in this section.)

NOTICE

Stow the rear center seat belt except

when you are wearing it.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

48

’03 Rav4_U (L/O 0208)

CAUTION

When using the seat belt extender,

observe the following precautions.

Failure to follow these instructions

could reduce the effectiveness of the

seat belt restraint system in case of

D After inserting the tab, make sure

the tab and buckle are locked and

that the seat belt extender is not

twisted.

D Do not insert coins, clips, etc. in

the buckle as this may prevent you

from properly latching the tab and

buckle.

vehicle

accident,

increasing

the

chance of personal injury.

D Never use the seat belt extender if

you can fasten the seat belt without

it.

D If the seat belt does not function

normally, immediately contact your

Toyota dealer. Do not use the seat

until the seat belt is fixed. It cannot

protect an adult occupant or your

child from injury.

D Remember that the extender pro-

vided for you may not be safe when

To connect the extender to the seat

belt, insert the tab into the seat belt

buckle so that the “PRESS” signs on

the buckle−release buttons of the ex-

tender and the seat belt are both facing

outward as shown.

used on

another person, or at

a

different vehicle, for

different

a

seating position than the one origi-

nally intended.

You will hear a click when the tab locks

into the buckle.

When releasing the seat belt, press on

the buckle−release button on the extender,

not on the seat belt. This helps prevent

damage to the vehicle interior and extend-

er itself.

When not in use, remove the extender

and store in the vehicle for future use.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

49

’03 Rav4_U (L/O 0208)

—Front seat belt

pretensioners

The driver and front passenger’s seat

belt pretensioners are designed to be

activated in response to a severe fron-

tal impact.

This indicator comes on when the igni-

The front seat belt pretensioner system

mainly consists of the following compo-

nents and their locations are shown in the

illustration.

tion key is turned to the “ON” position.

It goes off after about 6 seconds. This

means the front seat belt pretensioners

are operating properly.

When the airbag sensor detects the shock

of a severe frontal impact, the front seat

belts are quickly drawn back in by the

retractors so that the belts snugly restrain

the front seat occupants.

1. Front airbag sensors

This warning light system monitors the

airbag sensor assembly, front airbag sen-

sors, front seat belt pretensioner assem-

blies, inflators, warning light, interconnect-

ing wiring and power sources. (For details,

see “Service reminder indicators and

warning buzzers” on page 93 in Section

1−5.)

2. SRS warning light

3. Front seat belt pretensioner assemblies

4. Airbag sensor assembly

The front seat belt pretensioners are acti-

vated even with no passenger in the front

seat.

The front seat belt pretensioners are con-

trolled by the airbag sensor assembly. The

airbag sensor assembly consists of a saf-

ing sensor and airbag sensor.

Collisions occurring at certain speeds and

angles may cause the seat belt preten-

sioners and SRS airbags not to operate

all together.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

50

’03 Rav4_U (L/O 0208)

When the front seat belt pretensioners are

activated, an operating noise may be

heard and a small amount of smoke−like

gas may be released. This gas is harm-

less and does not indicate that a fire is

occurring.

NOTICE

Do not perform any of the following

changes without consulting your

Toyota dealer. Such changes can

interfere with proper operation of the

front seat belt pretensioners in some

cases.

Once the front seat belt pretensioners

have been activated, the seat belt retrac-

tors remain locked.

z Installation of electronic devices

such as

a

mobile two−way radio,

CAUTION

cassette tape player or compact

disc player

Do not modify, remove, strike or open

the front seat belt pretensioner as-

semblies, airbag sensor or surround-

ing area or wiring. Doing so may

cause sudden operation of the front

seat belt pretensioners or disable the

system, which could result in death

or serious injury.

z Repairs on or near the front seat

belt retractor assemblies

This front seat belt pretensioner system

has a service reminder indicator to inform

the driver of operating problems. If any of

the following conditions occurs, this

indicates a malfunction of the airbags or

pretensioners. Contact your Toyota dealer

as soon as possible to service the

vehicle.

z Modification of the suspension sys-

tem

z Modification of the front end struc-

ture

z Attachment of a grille guard (bull

bar, kangaroo bar, etc.), snowplow,

winches or any other equipment to

the front end

Failure to follow these instructions

can result in death or serious inju-

ries. Consult your Toyota dealer

about any repairs and modifications.

D The light does not come on when the

ignition key is turned to the “ON” posi-

tion, or the light remains on.

z Repairs made on or near the front

fenders, front end structure or con-

sole

D The light comes on or flashes while

driving.

D If either front seat belt does not retract

or cannot be pulled out due to a mal-

function or activation of the relevant

front seat belt pretensioner.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

51

’03 Rav4_U (L/O 0208)

SRS driver airbag and front

passenger airbag

Your vehicle is equipped with

a

crash

sensing and diagnostic module, which will

record the use of the seat belt restraint

system by the driver and front passenger

when the SRS airbags are inflated.

CAUTION

The driver or front passenger who is

too close to the steering wheel or

dashboard during airbag deployment

can be killed or seriously injured.

Toyota strongly recommends that:

D The driver sit as far back as pos-

sible from the steering wheel while

still maintaining control of the ve-

hicle.

In the following cases, contact your Toyota

dealer as soon as possible:

The SRS (Supplemental Restraint Sys-

tem) airbags are designed to provide

further protection for the driver and

front passenger in addition to the pri-

mary safety protection provided by the

seat belts.

D The front of the vehicle (shaded in the

illustration) was involved in an accident

that was not severe enough to cause

the front seat belt pretensioners to op-

erate.

D The front passenger sit as far back

as possible from the dashboard.

D All vehicle occupants be properly

restrained using the available seat

belts.

In response to a severe frontal impact,

the SRS airbags work together with the

seat belts to help reduce injury by inflat-

ing. The SRS airbags help to reduce inju-

ries mainly to the driver’s or front passen-

ger’s head or chest caused by directly

hitting the steering wheel or dashboard.

The front passenger airbag is activated

even with no passenger in the front seat.

D Either front seat belt pretensioner as-

sembly

or

surrounding

area

is

scratched, cracked, or otherwise dam-

aged.

Be sure to wear your seat belt properly.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

52

’03 Rav4_U (L/O 0208)

However, this threshold velocity will be

considerably higher if the vehicle strikes

an object, such as a parked vehicle or

sign pole, which can move or deform on

impact, or if it is involved in an underride

collision (e.g. a collision in which the nose

of the vehicle “underrides”, or goes under,

the bed of a truck, etc.).

It is possible that in some collisions at the

lower zone of airbag sensor detection and

activation the SRS airbags and front seat

belt pretensioners will not operate all toge-

ther.

For the safety of all occupants, always

wear your seat belts properly.

This indicator comes on when the igni-

tion key is turned to the “ON” position.

It goes off after about 6 seconds. This

means the SRS airbags are operating

properly.

The SRS airbag system is designed to

activate in response to a severe frontal

impact within the shaded area between

the arrows in the illustration.

The SRS airbags will deploy if the severi-

ty of the impact is above the designed

threshold level, comparable to an approxi-

mate 25 km/h (15 mph) collision when

impacting straight into a fixed barrier that

does not move or deform.

This warning light system monitors the

airbag sensor assembly, front airbag sen-

sors, front seat belt pretensioner assem-

blies, inflators, warning light, interconnect-

ing wiring and power sources. (For details,

see “Service reminder indicators and

warning buzzers” on page 93 in Section

1−5.)

If the severity of the impact is below the

above threshold level, the SRS airbags

may not deploy.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

53

’03 Rav4_U (L/O 0208)

Hitting a curb, edge

of pavement or

hard material

Falling into or

jumping over

a deep hole

Collision from the rear

Collision from the side

Vehicle rollover

Landing hard or vehicle falling

The SRS airbags are not designed to

inflate if the vehicle is involved in a

side or rear collision, if it rolls over, or

if it is involved in a low−speed frontal

collision.

The SRS airbags may deploy if a seri-

ous impact occurs to the underside of

your vehicle. Some examples are shown

in the illustration.

The SRS airbag system consists mainly of

the following components, and their loca-

tions are shown in the illustration.

1. Front airbag sensors

2. SRS warning light

3. Airbag module for front passenger

(airbag and inflator)

4. Airbag sensor assembly

5. Airbag module for driver

(airbag and inflator)

The airbag sensor assembly consists of a

safing sensor and airbag sensor.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

54

’03 Rav4_U (L/O 0208)

In a severe frontal impact, the sensor de-

tects deceleration and the system triggers

the airbag inflators. At this time a chemi-

cal reaction in the inflators quickly fills the

airbags with non−toxic gas to help restrain

the forward motion of the occupants.

A crash severe enough to inflate the air-

CAUTION

bags may break the windshield as the

vehicle buckles. In vehicles with a pas-

senger airbag the windshield may also be

damaged by absorbing some of the force

of the inflating airbag.

D The SRS airbag system is designed

only as a supplement to the prima-

ry protection of the driver side and

front passenger side seat belt sys-

tems. The front seat occupants can

be killed or seriously injured by the

inflating airbags if they do not wear

the available seat belts properly.

During sudden braking just before

a collision, an unrestrained driver

or front passenger can move for-

ward into direct contact with or

close proximity to the airbag which

may then deploy during the colli-

sion. To ensure maximum protection

in an accident, the driver and all

passengers in the vehicle must

wear their seat belts properly. Wear-

ing a seat belt properly during an

accident reduces the chances of

death or serious injury or being

thrown out of the vehicle. For

instructions and precautions con-

cerning the seat belt system, see

“Seat belts” on page 42 in this sec-

tion.

When the airbags inflate, they produce a

fairly loud noise and release some smoke

and residue along with non−toxic gas. This

does not indicate a fire. This gas is nor-

mally harmless; however, for those who

have delicate skin, it may cause a minor

skin irritation. Be sure to wash off any

residue as soon as possible to prevent

any potential skin irritation.

Deployment of the airbags happens in a

fraction of a second, so the airbags must

inflate with considerable force. While the

system is designed to reduce serious inju-

ries, it may also cause minor burns or

abrasions and swelling.

Parts of the airbag module (steering wheel

hub, dashboard) may be hot for several

minutes, but the airbags themselves will

not be hot. The airbags are designed to

inflate only once.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

55

’03 Rav4_U (L/O 0208)

D Improperly seated and/or restrained

infants and children can be killed

or seriously injured by the deploy-

ing airbags. An infant or child who

is too small to use

should be properly secured using a

child restraint system. Toyota

a

seat belt

strongly recommends that all in-

fants and children be placed in the

rear seat of the vehicle and proper-

ly restrained. The rear seat is the

safest for infants and children. For

instructions concerning the installa-

tion of a child restraint system, see

“Child restraint” on page 59 in this

section.

Move seat

fully back

D Never install a rear−facing child re-

straint system on the front passen-

ger seat because the force of the

rapid inflation of the front passen-

ger airbag can cause death or seri-

ous injury to the child.

D A forward−facing child restraint sys-

tem should be allowed to be

installed on the front passenger

seat only when it is unavoidable.

Always move the seat as far back

as possible, because the force of

the deploying front passenger air-

bag could cause death or serious

injury to the child.

D For instructions concerning the

installation of a child restraint sys-

tem, see “Child restraint” on page

59 in this section.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

56

’03 Rav4_U (L/O 0208)

D Do not sit on the edge of the seat

or lean over the dashboard when

the vehicle is in use, since the air-

D Do not allow a child to stand up,

or to kneel on the front passenger

seat, since the airbag inflates with

D Do not put objects or your pets on

or in front of the dashboard or

steering wheel pad that houses the

airbag system. They might restrict

inflation or cause death or serious

injury as they are projected rear-

ward by the force of the deploying

airbags. Likewise, the driver and

front passenger should not hold ob-

jects in their arms or on their

knees.

bags

inflate

with

considerable

speed

and

force.

speed and force. Otherwise you

may be killed or seriously injured.

Sit up straight and well back in the

seat, and always use your seat belt

properly.

Otherwise, the child may be killed

or seriously injured.

D Do not hold a child on your lap or

in your arms. Use a child restraint

system in the rear seat. For instruc-

tions concerning the installation of

a child restraint system, see “Child

restraint” on page 59 in this sec-

tion.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

57

’03 Rav4_U (L/O 0208)

NOTICE

Do not perform any of the following

D Do not modify or remove any wir-

ing. Do not modify, remove, strike

or open any components, such as

the steering wheel pad, steering

wheel, column cover, front passen-

ger airbag cover, front passenger

airbag or airbag sensor assembly.

Doing so may cause sudden SRS

airbag inflation or disable the sys-

tem, which could result in death or

serious injury.

changes without consulting your

Toyota dealer. Such changes can

interfere with proper operation of the

SRS airbag system in some cases.

z Installation of electronic devices

such as

a

mobile two−way radio,

cassette tape player or compact

disc player

z Modification of the suspension sys-

tem

Failure to follow these instructions

can result in death or serious injury.

Consult your Toyota dealer about any

repairs and modifications.

This SRS airbag system has

a

service

z Modification of the front end struc-

ture

reminder indicator to inform the driver of

operating problems. If either of the follow-

z Attachment of a grille guard (bull

bar, kangaroo bar, etc.), snowplow,

winches or any other equipment to

the front end

ing conditions occurs, this indicates

a

malfunction of the airbags. Contact your

Toyota dealer as soon as possible to

service the vehicle.

z Repairs made on or near the front

fenders, front end structure, con-

sole, steering column, steering

wheel or dashboard near the front

passenger airbag

D The light does not come on when the

ignition key is turned to the “ON” posi-

tion, or the light remains on.

D The light comes on while driving.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

58

’03 Rav4_U (L/O 0208)

Child restraint—

—Child restraint precautions

Toyota strongly urges the use of child

restraint systems for children small

enough to use them.

D Toyota strongly urges use of

a

proper child restraint system which

conforms to the size of the child,

installed on the rear seat. Accord-

ing to accident statistics, the child

is safer when properly restrained in

the rear seat than in the front seat.

The laws of all 50 states in the U.S.A.

and Canada now require the use of

child restraint system.

a

Your vehicle conforms to SAEJ1819.

If a child is too large for a child restraint

system, the child should sit in the rear

seat and must be restrained using the

vehicle’s seat belt. See “Seat belts” on

page 42 for details.

D Never install a rear−facing child re-

straint system on the front seat. In

the event of an accident, the force

of the rapid inflation of the airbag

can cause death or serious injury if

a rear−facing child restraint system

is installed on the front seat.

In the following cases, contact your Toyota

dealer as soon as possible:

CAUTION

D Unless it is unavoidable, do not

D For effective protection in automo-

bile accidents and sudden stops, a

child must be properly restrained,

using a seat belt or child restraint

system depending on the age and

size of the child. Holding a child in

your arms is not a substitute for a

child restraint system. In an acci-

dent, the child can be crushed

against the windshield, or between

you and the vehicle’s interior.

D The SRS airbags have been inflated.

install

a

forward−facing child re-

straint system on the front seat.

D The front of the vehicle (shaded in the

illustration) was involved in an accident

that was not severe enough to cause

the SRS airbags to inflate.

D A forward−facing child restraint sys-

tem should be allowed to be

installed on the front passenger

seat only when it is unavoidable.

Always move the seat as far back

as possible, because the force of

the deploying front passenger air-

bag could cause death or serious

injury to the child.

D The pad section of the steering wheel

or

front passenger

airbag cover

(shaded in the illustration) is scratched,

cracked, or otherwise damaged.

NOTICE

Do not disconnect the battery cables

before contacting your Toyota dealer.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

59

’03 Rav4_U (L/O 0208)

—Child restraint system

A

child restraint system for

a

small

D Make sure that you have complied

with all installation instructions pro-

CAUTION

child or baby must itself be properly

restrained on the seat with the lap por-

tion of the lap/shoulder belt. You must

carefully consult the manufacturer’s

instructions which accompany the child

restraint system.

vided

by

the

child

restraint

D Never install a rear−facing child re-

straint system on the front seat. In

the event of an accident, the force

of the rapid inflation of the airbag

can cause death or serious injury if

a rear−facing child restraint system

is installed on the front seat.

manufacturer and that the system is

properly secured.

To provide proper restraint, use a child

restraint system following the manufactur-

er’s instructions about the appropriate age

and size of the child for the child restraint

system.

D Unless it is unavoidable, do not

forward−facing child re-

straint system on the front seat.

install

a

Install the child restraint system correctly

following the instructions provided by its

manufacturer. General directions are also

provided under the following illustrations.

D A forward−facing child restraint sys-

tem should be allowed to be

installed on the front passenger

seat only when it is unavoidable.

Always move the seat as far back

as possible, because the force of

the deploying front passenger air-

bag could cause death or serious

injury to the child.

The child restraint system should be

installed on the rear seat. According to

accident statistics, the child is safer when

properly restrained in the rear seat than

in the front seat.

D After installing the child restraint

system, make sure it is secured in

place following the manufacturer’s

instructions. If it is not restrained

securely, it may cause death or se-

rious injury to the child in the

event of a sudden stop or accident.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

60

’03 Rav4_U (L/O 0208)

—Types of child restraint

system

When not using the child restraint system,

keep it secured with the seat belt or place

it somewhere other than the passenger

compartment. This will prevent it from in-

juring passengers in the event of a sud-

den stop or accident.

Child restraint systems are classified into

the following 3 types depending on the

child’s age and size.

(A) Infant seat

(B) Convertible seat

(C) Booster seat

Install the child restraint system following

the instructions provided by its manufac-

turer.

Your vehicle has anchor brackets for se-

curing the top strap of a child restraint

system.

For instructions about how to use the an-

chor bracket, see “—Using a top strap” on

page 71 in this section.

(A) Infant seat

The child restraint lower anchorages ap-

proved for your vehicle may also be used.

See “—Installation with child restraint low-

er anchorages” on page 74 in this section.

(B) Convertible seat

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

61

’03 Rav4_U (L/O 0208)

—Installation with seat belt

(C) Booster seat

(A) INFANT SEAT INSTALLATION

CAUTION

An infant seat is used in rear−facing

position only.

D Never install a rear−facing child re-

straint system on the front passen-

ger seat because the force of the

rapid inflation of the front passen-

ger airbag can cause death or seri-

ous injury to the child.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

62

’03 Rav4_U (L/O 0208)

Same position

Same angle

1. Run the lap and shoulder belt through

or around the infant seat following the

instructions provided by its manufactur-

er and insert the tab into the buckle

taking care not to twist the belt. Keep

the lap portion of the belt tight.

D Do not install a child restraint sys-

tem on the rear seat if it interferes

with the lock mechanism of the

front seats. This can cause death or

serious injury to the child and front

passenger in case of sudden brak-

ing or a collision.

D When installing

a

child restraint

system on the rear center position,

adjust both seat cushions to the

same position and align both seat-

backs at the same angle. Otherwise,

the child restraint system cannot be

securely restrained and this may

cause death or serious injuries in a

collision.

D If the driver’s seat position does

not allow sufficient space for safe

installation, install the child re-

straint system on the rear right

seat.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

63

’03 Rav4_U (L/O 0208)

CAUTION

D After inserting the tab, make sure

the tab and buckle are locked and

that the lap and shoulder portions

of the belt are not twisted.

D Do not insert coins, clips, etc. in

the buckle as this may prevent you

from properly latching the tab and

buckle.

D If the seat belt does not function

normally, it cannot protect your

child from injury. Contact your

Toyota dealer immediately. Do not

use the child restraint system until

the seat belt is fixed.

2. Fully extend the shoulder belt to put it

3. While pressing the infant seat firmly

against the seat cushion and seatback,

let the shoulder belt retract as far as

it will go to hold the infant seat secure-

ly.

in the lock mode. When the belt is

then retracted even slightly, it cannot

be extended.

To hold the infant seat securely, make

sure the belt is in the lock mode before

letting the belt retract.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

64

’03 Rav4_U (L/O 0208)

4. To remove the infant seat, press the

(B) CONVERTIBLE SEAT INSTALLATION

CAUTION

buckle−release button and allow the

belt to retract completely. The belt will

move freely again and be ready to

work for an adult or older child passen-

ger.

A convertible seat is used in forward−

facing or rear−facing position depend-

ing on the child’s age and size. When

installing, follow the manufacturer’s in-

struction about the applicable child’s

age and size as well as directions for

installing the child restraint system.

Push and pull the child restraint sys-

tem in different directions to be sure

it is secure. Follow all the installation

instructions provided by its manufac-

turer.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

65

’03 Rav4_U (L/O 0208)

Move seat

fully back

D A forward−facing child restraint sys-

tem should be allowed to be

installed on the front passenger

seat only when it is unavoidable.

Always move the seat as far back

as possible, because the force of

the deploying front passenger air-

bag could cause death or serious

injury to the child.

D Do not install a child restraint sys-

tem on the rear seat if it interferes

with the lock mechanism of the

front seats. This can cause death or

serious injury to the child and front

passenger in case of sudden brak-

ing or a collision.

CAUTION

D Never install a rear−facing child re-

straint system on the front passen-

ger seat because the force of the

rapid inflation of the front passen-

ger airbag can cause death or seri-

ous injury to the child.

D If the driver’s seat position does

not allow sufficient space for safe

installation, install the child re-

straint system on the rear right

seat.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

66

’03 Rav4_U (L/O 0208)

CAUTION

Same

angle

Same position

D After inserting the tab, make sure

the tab and buckle are locked and

that the lap and shoulder portions

of the belt are not twisted.

D Do not insert coins, clips, etc. in

the buckle as this may prevent you

from properly latching the tab and

buckle.

D If the seat belt does not function

normally, it cannot protect your

child from injury. Contact your

Toyota dealer immediately. Do not

use the child restraint system until

the seat belt is fixed.

1. Run the lap and shoulder belt through

or around the convertible seat following

D When installing

a

child restraint

system on the rear center position,

adjust both seat cushions to the

same position and align both seat-

backs at the same angle. Otherwise,

the child restraint system cannot be

securely restrained and this may

cause death or serious injuries in a

collision.

the

instructions

provided

by

its

manufacturer and insert the tab into

the buckle taking care not to twist the

belt. Keep the lap portion of the belt

tight.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

67

’03 Rav4_U (L/O 0208)

2. Fully extend the shoulder belt to put it

in the lock mode. When the belt is

then retracted slightly, it cannot be ex-

tended.

3. While pressing the convertible seat

CAUTION

firmly against the seat cushion and

seatback, let the shoulder belt retract

as far as it will go to hold the convert-

ible seat securely.

Push and pull the child restraint sys-

tem in different directions to be sure

it is secure. Follow all the installation

instructions provided by its manufac-

turer.

To hold the convertible seat securely,

make sure the belt is in the lock mode

before letting the belt retract.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

68

’03 Rav4_U (L/O 0208)

Move seat

fully back

4. To remove the convertible seat, press

the buckle−release button and allow the

belt to retract completely. The belt will

move freely again and be ready to

work for an adult or older child passen-

ger.

(C) BOOSTER SEAT INSTALLATION

CAUTION

A booster seat is used in forward−fac-

ing position only.

D A forward−facing child restraint sys-

tem should be allowed to be

installed on the front passenger

seat only when it is unavoidable.

Always move the seat as far back

as possible, because the force of

the deploying front passenger air-

bag could cause death or serious

injury to the child.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

69

’03 Rav4_U (L/O 0208)

CAUTION

Same

angle

Same position

D Always make sure the shoulder belt

is positioned across the center of

child’s shoulder. The belt should be

kept away from child’s neck, but

not falling off child’s shoulder. Fail-

ure to do so could reduce the

amount of protection in an accident

and cause serious injuries in a col-

lision.

D Both high−positioned lap belts and

loose−fitting belts could cause seri-

ous injuries due to sliding under

the lap belt during a collision or

other unintended. Keep the lap belt

positioned as low on a child’s hips

as possible.

1. Sit the child on a booster seat. Run

the lap and shoulder belt through or

around the booster seat and child fol-

lowing the instructions provided by its

manufacturer and insert the tab into

the buckle taking care not to twist the

belt.

D When installing

a

child restraint

system on the rear center position,

adjust both seat cushions to the

same position and align both seat-

backs at the same angle. Otherwise,

the child restraint system cannot be

securely restrained and this may

cause death or serious injuries in a

collision.

D For child’s safety, do not place the

shoulder belt under child’s arm.

Make sure the shoulder belt is correctly

across the child’s shoulder and that the

lap belt is positioned as low as possible

on child’s hips. See “Seat belts” on page

42 for details.

D After inserting the tab, make sure

the tab and buckle are locked and

that the lap and shoulder portions

of the belt are not twisted.

D Do not insert coins, clips, etc. in

the buckle as this may prevent your

child from properly latching the tab

and buckle.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

70

’03 Rav4_U (L/O 0208)

—Using a top strap

D If the seat belt does not function

normally, it cannot protect your

child from injury. Contact your

Toyota dealer immediately. Do not

use the child restraint system until

the seat belt is fixed.

Outside position

2. To remove the child restraint system,

press the buckle−release button and al-

low the belt to retract.

Center position (U.S.A. only)

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

71

’03 Rav4_U (L/O 0208)

Follow the procedure below for a child

restraint system that requires the use

of a top strap.

For U.S.A.—

Use the anchor brackets behind the rear

seatbacks and on the luggage compart-

ment to attach the top strap.

Anchor brackets

Anchor brackets are installed for each

rear seating position.

For Canada—

Use the anchor brackets behind the rear

seatbacks to attach the top strap.

Anchor brackets are installed for both out-

side rear seating positions.

U.S.A.

Anchor brackets

Canada

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

72

’03 Rav4_U (L/O 0208)

2. Fix the child restraint system with

the seat belt.

Center anchor bracket only—

Run the top strap through between

both seatbacks.

Latch the hook onto the anchor

bracket and tighten the top strap.

For instructions to install the child re-

straint system, see “Child restraint” on

page 59 in this section.

CAUTION

Outside position

TO USE THE ANCHOR BRACKET:

D When you use the center anchor

bracket, make sure the top strap

runs through between both seat-

backs and tighten it. The top strap

on seatback could cause death or

serious injury due to abnormal

moving of the child restraint system

in case of sudden braking or a col-

lision.

1. Outside anchor brackets only—

Remove the head restraint.

D Make sure the top strap is securely

latched, and check that the child

restraint system is secure by push-

ing and pulling it in different direc-

tions. Follow all the installation in-

structions provided by its manufac-

turer.

Center position (U.S.A. only)

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

73

’03 Rav4_U (L/O 0208)

—Installation with child

restraint lower anchorages

3. Outside anchor brackets only—

Replace the head restraint.

The lower anchorages for the child re-

straint system interfaced with the

FMVSS225 specification are installed in

the rear seat.

The anchorages are installed in the clear-

ance between the seat cushion and seat-

back of both outside rear seats.

Child restraint system interfaced with the

FMVSS225 specification can be fixed with

these anchorages. In this case, it is not

necessary to fix the child restraint system

with a seat belt on the vehicle.

Type A

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

74

’03 Rav4_U (L/O 0208)

CHILD

INSTALLATION

RESTRAINT

SYSTEM

CAUTION

Type A—

D When using the lower anchorages

for the child restraint system, be

sure that there are no irregular ob-

jects around the anchorages or that

the seat belt is not caught.

1. Widen the clearance between the

seat cushion and seatback little

a

and confirm the position of the low-

er anchorages below the tag in the

seatback.

D Push and pull the child restraint

system in different directions to be

sure it is secure. Follow all the

installation instructions provided by

its manufacturer.

2. Latch the hooks of lower straps onto

the anchorages and tighten the lower

straps.

Type B—

D When using the lower anchorages

for the child restraint system, en-

sure that the seat is moved to the

rear−most position, with the seat-

back close to the child restraint

system.

1. Widen the clearance between the

seat cushion and seatback

a

little

and confirm the position of the low-

er anchorages below the tag in the

seatback.

2. Latch the buckles onto the anchor-

ages.

D After securing the child restraint

system, never slide or recline the

seat.

If your child restraint system has a top

strap, it should be anchored. (For the

installation of the top strap, see “—Using

a top strap” on page 71 in this section.)

D Do not install a child restraint sys-

tem on the rear seat if it interferes

with the lock mechanism of the

front seats. This can cause death or

severe injury to the child and front

passenger in case of sudden brak-

ing or a collision.

For the installation details, refer to the

instruction manual equipped with each

product.

Type B

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

75

’03 Rav4_U (L/O 0208)

Tilt steering wheel

Outside rear view mirrors—

CAUTION

D Do not adjust the steering wheel

while the vehicle is moving. Doing

so may cause the driver to mishan-

dle the vehicle and an accident may

occur resulting in death or serious

injuries.

D After adjusting the steering wheel,

try moving it up and down to make

sure it is locked in position.

To change the steering wheel angle,

hold the steering wheel, push down the

lock release lever, tilt the steering

wheel to the desired angle and return

the lever to its original position.

Adjust the mirror so that you can just

see the side of your vehicle in the mir-

ror.

Be careful when judging the size or dis-

tance of any object seen in the outside

rear view mirror on the passenger’s side.

It is a convex mirror with a curved sur-

face. Any object seen in a convex mirror

will look smaller and farther away than

when seen in a flat mirror.

On some models, when you push the rear

window defogger switch, the heater panels

in the outside rear view mirrors will quick-

ly clear the mirror surface. (See “Rear

window and outside rear view mirror de-

foggers” on page 87 in section 1−4.)

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

76

’03 Rav4_U (L/O 0208)

—Power rear view mirror

control

—Folding rear view mirrors

CAUTION

D Do not adjust the mirror while the

vehicle is moving. Doing so may

cause the driver to mishandle the

vehicle and an accident may occur

resulting in death or serious inju-

ries.

D Since the mirror surfaces can get

hot, do not touch them when the

defogger switch is on.

To adjust a mirror, use the switches.

The rear view mirrors can be folded

backward for parking in restricted

areas.

1. Master switch—To select the mirror to

be adjusted

Push the “L” (left) or “R” (right) switch.

To fold the rear view mirror, push back-

ward.

2. Control switch—To move the mirror

Push the switch in the desired direc-

tion.

CAUTION

Mirrors can be adjusted when the key is

in the “ACC” or “ON” position.

Do not drive with the mirrors folded

backward. Both the driver and pas-

senger side rear view mirrors must

be extended and properly adjusted

before driving.

NOTICE

If ice should jam the mirror, do not

operate the control or scrape the mir-

ror face. Use a spray de−icer to free

the mirror.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

77

’03 Rav4_U (L/O 0208)

Anti−glare inside rear view

mirror

Sun visors—

CAUTION

Do not adjust the mirror while the

vehicle is moving. It may cause the

driver to mishandle the vehicle and

an accident may occur resulting in

death or serious injuries.

Adjust the mirror so that you can just

see the rear of your vehicle in the mir-

ror.

To block out glare, move the sun visor.

To block out glare from the front—Swing

down the sun visor (position 1).

To reduce glare from the headlights of

the vehicle behind you during night

driving, operate the lever on the lower

edge of the mirror.

To block out glare from the side—Swing

down the sun visor, remove it from the

hook and swing it to the lateral side (posi-

tion 2).

Daylight driving—Lever at position 1

If glare comes from obliquely behind you,

extend the plate at the end of the visor

(to position 3).

The reflection in the mirror has greater

clarity at this position.

Night driving—Lever at position 2

Remember that by reducing glare you also

lose some rear view clarity.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

78

’03 Rav4_U (L/O 0208)

—Vanity mirrors

CAUTION

Do not extend the plate at the end of

the sun visor when the visor is in the

position 1. It can cover the anti−glare

inside rear view mirror and obstruct

the rear view.

To use the vanity mirrors, swing down

the sun visor and open the cover.

2003 RAV4 from Aug. ’02 Prod. (OM42517U)

79

Seats, Seat belts, Steering wheel and Mirrors for Your Toyota Rav4 SUV Second Generation (2001-2005)

Related Topics

Popular Owner Manuals

Latest Owner Manuals