IN CASE OF AN EMERGENCY for Your Toyota Yaris 4 Door Second Generation (2006-2011)

2-5. Driving information  
Towing a trailer  
Consult your Toyota dealer for further information about additional  
requirements such as a towing kits, etc.  
Before towing  
Check that the following conditions are met:  
Ensure that your vehicle’s tires are properly inflated. (P. 333)  
2
Trailer tires should be inflated according to the trailer manufacturer’s rec-  
ommendation.  
All trailer lights work to be legal.  
Confirm all lights work each time you connect them.  
Check that your vehicle remains level when a loaded or unloaded trailer  
is hitched. Do not drive if the vehicle is not level, and check for improper  
tongue load, overloading, worn suspension, or other possible causes.  
Make sure the trailer cargo is securely loaded.  
Check that your rear view mirrors conform to any federal, state/provincial  
or local regulations. If they do not, install rear view mirrors appropriate for  
towing purposes.  
Break-in schedule  
Toyota recommends that you do not use a new vehicle or a vehicle with  
any new power train components (engine, transmission, differential,  
wheel bearings, etc.) to tow a trailer for the first 500 miles (800 km) of  
driving.  
Maintenance  
If you tow a trailer, your vehicle will require more frequent maintenance  
due to the additional load. (See “Scheduled Maintenance Guide” or  
“Owner’s Manual Supplement”.)  
Retighten the fixing bolts of the towing ball and bracket after approxi-  
mately 600 miles (1000 km).  
147  
2-5. Driving information  
CAUTION  
To avoid accident or injury  
The total trailer weight (trailer weight plus the weight of cargo) must not  
exceed 700 lb. (318 kg)  
Do not exceed the trailer hitch assembly weight, gross vehicle weight,  
gross axle weight and trailer tongue load capacities.  
Hitches  
Trailer hitch assemblies have different weight capacities established by the  
hitch manufacturer. Even though the vehicle may be rated for towing a  
higher weight, the operator must never exceed the maximum weight rating  
specified for the trailer hitch.  
If you wish to install a trailer hitch, your Toyota dealer should be consulted.  
Use only a hitch that conforms to the total trailer weight requirement.  
Follow the directions supplied by the hitch manufacturer.  
Lubricate the hitch ball with a light coat of grease.  
Remove the trailer hitch whenever you are not towing a trailer to reduce  
the possibility of additional damage caused by the hitch if your vehicle is  
struck from behind.  
When towing a trailer  
Never tap into your vehicle’s hydraulic system, as this will lower the vehi-  
cle’s braking effectiveness.  
Never tow a trailer without using a safety chain securely attached to both  
the trailer and the vehicle. If damage occurs to the coupling unit or hitch  
ball, there is danger of the trailer wandering into another lane.  
148  
2-5. Driving information  
NOTICE  
When installing a trailer hitch  
Use only the position recommended by your Toyota dealer. Do not install the  
trailer hitch on the bumper; this may cause body damage.  
Brakes  
Toyota recommends trailers with brakes that conform to any applicable fed-  
eral and state/provincial regulations.  
2
Safety chain  
A safety chain must always be used between the towing vehicle and the  
trailer. Leave sufficient slack in the chain for turns. The chain should cross  
under the trailer tongue to prevent the tongue from dropping to the ground in  
the case that it becomes damaged or separated. For the correct safety chain  
installation procedure, ask your Toyota dealer.  
Do not directly splice trailer lights  
Directly splicing may damage your vehicle’s electrical system and cause a  
malfunction.  
Trailer towing tips  
Your vehicle will handle differently when towing a trailer. The three  
main causes of vehicle-trailer accidents are driver error, excessive  
speed and improper trailer loading. Keep these in mind when towing.  
Before starting out, check the trailer’s light and the vehicle-trailer  
connections. Recheck after driving a short distance.  
Practice turning, stopping and reversing with the trailer attached in  
an area away from traffic until you become accustomed to the feel  
of the vehicle.  
149  
2-5. Driving information  
Reversing with a trailer attached is difficult and requires practice.  
Grip the bottom of the steering wheel and move your hand to the  
left to move the trailer to the left. Move your hand to the right to  
move the trailer to the right. (This is generally opposite to reversing  
without a trailer attached.) Avoid sharp or prolonged turning. Have  
someone guide you when reversing to reduce the risk of an acci-  
dent.  
As stopping distance is increased when towing a trailer, vehicle-to-  
vehicle distance should be increased. For each 10 mph (16 km/h)  
of speed, allow at least one vehicle and trailer length.  
Avoid sudden braking as you may skid, resulting in jackknifing and  
loss of control. This is especially true on wet or slippery surfaces.  
Avoid jerky starts or sudden acceleration. Vehicles with a manual  
transmission, prevent excessive clutch slippage by keeping engine  
rpm low and not racing the engine. Always start out in first gear.  
Avoid jerky steering and sharp turns, and slow down before mak-  
ing a turn.  
Note that when making a turn, the trailer wheels will be closer than  
the vehicle wheels to the inside of the turn. Compensate by making  
a larger than normal turning radius.  
Crosswinds and rough roads will adversely affect handling of your  
vehicle and trailer, causing sway. Periodically check the rear to  
prepare for being passed by large trucks or buses, which may  
cause your vehicle and trailer to sway. If swaying occurs, firmly grip  
the steering wheel, reduce speed immediately but gradually, and  
steer straight ahead. Never increase speed. If you make no  
extreme correction with the steering or brakes, your vehicle and  
trailer will stabilize.  
Take care when passing other vehicles. Passing requires consider-  
able distance. After passing a vehicle, do not forget the length of  
your trailer, and be sure you have plenty of room before changing  
lanes.  
150  
2-5. Driving information  
In order to maintain engine braking efficiency, do not use the trans-  
mission in D (automatic transmission) or 5 (manual transmission).  
Due to the added load of the trailer, your vehicle’s engine may  
overheat on hot days (at temperatures over 85°F [30°C]) when  
driving up a long or steep grade. If the engine coolant temperature  
gauge indicates overheating, immediately turn off the air condition-  
ing (if in use), pull your vehicle off the road and stop in a safe spot.  
(P. 320)  
2
Always place wheel blocks under both the vehicle and the trailer  
wheels when parking. Apply the parking brake firmly, and put the  
transmission in P (automatic transmission) or in 1 or R (manual  
transmission). Avoid parking on a slope, but if unavoidable, do so  
only after performing the following:  
Apply the brakes and keep them applied.  
Have someone place wheel blocks under both the vehicle and  
trailer wheels.  
When the wheel blocks are in place, release the brakes slowly  
until the blocks absorb the load.  
Apply the parking brake firmly.  
Shift into 1 or R (manual transmission) or P (automatic trans-  
mission) and turn off the engine.  
When restarting after parking on a slope:  
With the transmission in P (automatic transmission) or the  
clutch pedal (manual transmission) depressed, start the  
engine. On vehicles with an automatic transmission, be sure  
to keep the brake pedal pressed.  
Shift into a forward gear. If reversing, shift into R.  
Release the parking brake (also brake pedal on vehicles with  
an automatic transmission), and slowly pull or back away from  
the wheel blocks. Stop and apply the brakes.  
Have someone retrieve the blocks.  
151  
2-5. Driving information  
CAUTION  
To avoid an accident  
Do not exceed 45 mph (72 km/h) or posted towing speed limit, whichever  
is lower. As instability (swaying) of the towing vehicle-trailer combination  
increases as speed increases, exceeding 45 mph (72 km/h) may cause  
loss of control.  
Slow down and downshift before descending steep or long downhill  
grades. Do not make sudden downshifts.  
Avoid holding the brake pedal down too long or too frequently. This could  
cause the brakes to overheat and result in reduced braking efficiency.  
152  
2-5. Driving information  
Dinghy towing (vehicles with an automatic transmission)  
Your vehicle is not designed to be dinghy towed (with 4 wheels on  
the ground) behind a motor home.  
2
NOTICE  
To avoid serious damage to your vehicle  
Do not tow your vehicle with four wheels on the ground.  
153  
2-5. Driving information  
Dinghy towing (vehicles with a manual transmission)  
Your vehicle can be dinghy towed in a forward direction (with 4  
wheels on the ground) behind a motor home.  
Dinghy towing does not elimi-  
nate the possibility of damage  
to your vehicle.  
Towing your vehicle with 4 wheels on the ground  
To prevent damage to your vehicle, perform the following procedures  
before towing.  
Shift the shift lever to N.  
Turn the engine switch to the ACC position.  
Ensure that the audio system and other powered devices have been  
turned off.  
Release the parking brake.  
After towing, leave the engine in idle for at least 3 minutes before  
driving the vehicle.  
Necessary equipment and accessories  
Specialized equipment and accessories are required for dinghy towing. Con-  
tact the service branch of the motor home manufacturer regarding recom-  
mended equipment.  
154  
2-5. Driving information  
NOTICE  
Dinghy towing direction  
Do not tow the vehicle backwards.  
Doing so may cause serious damage.  
2
To prevent the steering from locking  
Ensure the engine switch is in the ACC position.  
155  
2-5. Driving information  
156  
Interior features  
3
3-1. Using the air conditioning  
system and defogger... 158  
3-4. Using the storage  
features......................... 193  
Air conditioning system.... 158  
Rear window defogger..... 164  
List of storage features .... 193  
• Glove box....................... 193  
• Console box................... 194  
• Cup holders (front)......... 195  
• Cup holders (rear)........... 196  
• Bottle holders................. 197  
• Auxiliary box .................. 197  
3-2. Using the audio  
system .......................... 165  
Audio system types ........... 165  
Using the radio................. 168  
Using the CD player......... 171  
3-5. Other interior features... 199  
Sun visors ........................ 199  
Vanity mirrors................... 200  
Clock................................ 201  
Portable ashtray............... 202  
Cigarette lighter................ 203  
Power outlet..................... 204  
Armrest ............................ 205  
Floor mat.......................... 206  
Playing back MP3 and  
WMA discs..................... 178  
Optimal use of the audio  
system .......................... 186  
Using the AUX adapter .... 189  
3-3. Using the interior  
lights ............................. 191  
Interior lights list............... 191  
• Interior light ................... 192  
• Personal lights ............... 192  
157  
3-1. Using the air conditioning system and defogger  
Air conditioning system  
Air conditioning ON/OFF switch  
Fan speed control dial  
Air outlet selection dial  
Air intake selection dial  
Temperature control dial  
Adjusting the settings  
Adjusting the temperature setting  
Turn the temperature control dial clockwise (warm) or counter-  
clockwise (cool).  
If  
is not pressed, the system will blow ambient temperature air or  
heated air.  
For quick cooling, turn the temperature control dial to the “MAX A/C”  
position and set the air intake selection dial to  
mode.  
(recirculated air)  
158  
3-1. Using the air conditioning system and defogger  
Adjusting the fan speed  
Turn the fan speed control dial clockwise (increase) or counter-  
clockwise (decrease).  
Set the dial to “0” to turn the fan off.  
Selecting the air outlets  
Set the air outlet selection dial to an appropriate position.  
The positions between the air outlet selections shown below can also be  
selected for more detailed adjustment.  
When the dial is set to  
flows to the upper body.  
, air  
3
When the dial is set to  
, air  
flows to the upper body and feet.  
: Some models  
159  
3-1. Using the air conditioning system and defogger  
When the dial is set to  
, air  
flows to the feet.  
: Some models  
When the dial is set to  
, air  
flows to the feet and the wind-  
shield defogger operates.  
: Some models  
When the dial is set to  
, air  
flows to the windshield and side  
windows.  
Set the air intake selection dial to  
(outside air) mode.  
Pressing  
to turn the air  
conditioning on clears the wind-  
shield and side windows faster.  
Selecting the air intake modes  
Set the air intake selection dial to  
(recirculated air) mode.  
(outside air) mode or  
160  
3-1. Using the air conditioning system and defogger  
Adjusting the position of the air outlets  
Center outlets  
Direct air flow to the left or right,  
up or down.  
3
161  
3-1. Using the air conditioning system and defogger  
Right and left side outlets  
Direct air flow to the left or right,  
up or down.  
Opening and closing the right and left side outlets  
Open the vent.  
Close the vent.  
162  
3-1. Using the air conditioning system and defogger  
Using the system in recirculated air mode  
The windows will fog up more easily if the recirculated air mode is used for  
an extended period.  
When outside air temperature approaches 32°F (0°C)  
The air conditioning system may not operate even when  
When is selected for the air outlets used  
is pressed.  
For your driving comfort, air flowing to the feet may be warmer than air flow-  
ing to the upper body depending on the position of the temperature adjust-  
ment dial.  
3
CAUTION  
To prevent the windshield from fogging up  
Do not set the air outlet selection dial to  
during cool air operation in  
extremely humid weather. The difference between the temperature of the  
outside air and that of the windshield can cause the outer surface of the  
windshield to fog up, blocking your vision.  
NOTICE  
To prevent battery discharge  
Do not leave the air conditioning system on longer than necessary when the  
engine is stopped.  
163  
3-1. Using the air conditioning system and defogger  
Rear window defogger (if equipped)  
Clear the rear window using the defogger.  
ON/OFF  
Press the button to turn on the  
rear window defogger. The  
indicator light will come on.  
The rear window defogger can be operated when  
The engine switch is in the ON position.  
NOTICE  
To prevent battery discharge  
Do not leave the rear window defogger on longer than necessary when the  
engine is stopped.  
164  
3-2. Using the audio system  
Audio system types  
CD player with CD changer controller and AM/FM radio.  
Type A  
3
Type B  
165  
3-2. Using the audio system  
Title  
Page  
P. 168  
P. 171  
P. 178  
P. 186  
P. 189  
Using the radio  
Using the CD player  
Playing back MP3 and WMA discs  
Optimal use of the audio system  
Using the AUX adapter  
Using cellular phones  
Interference may be heard through the audio system's speakers if a cellular  
phone is being used inside or close to the vehicle while the audio system is  
operating.  
CAUTION  
For vehicles sold in U.S.A. and Canada  
Part 15 of the FCC Rules  
FCC Warning:  
Any unauthorized changes or modifications to this equipment will void the  
user’s authority to operate this device.  
Laser products  
• Do not take this unit apart or attempt to make any changes yourself.  
This is an intricate unit that uses a laser pickup to retrieve information  
from the surface of compact discs. The laser is carefully shielded so  
that its rays remain inside the cabinet. Therefore, never try to disas-  
semble the player or alter any of its parts since you may be exposed to  
laser rays and dangerous voltages.  
• This product utilizes a laser.  
Use of controls or adjustments or performance of procedures other  
than those specified herein may result in hazardous radiation expo-  
sure.  
166  
3-2. Using the audio system  
NOTICE  
To prevent battery discharge  
Do not leave the audio system on longer than necessary with the engine off.  
To avoid damaging the audio system  
Take care not to spill drinks or other fluids over the audio system.  
3
167  
3-2. Using the audio system  
Using the radio  
\
Type A  
Power  
Volume  
Adjusting the  
frequency  
Station selector  
AM/FM mode buttons  
Seeking the frequency  
Scanning for receivable  
stations  
Type B  
Power  
Volume  
Adjusting the  
frequency  
Station selector  
Scanning for receivable stations  
Seeking the frequency AM/FM mode buttons  
168  
3-2. Using the audio system  
Setting station presets  
Search for desired stations by turning  
pressing “or “” on or  
Press and hold the button (from  
or  
or  
or  
.
or  
to  
) that the station is to be set to until you hear a beep.  
Scanning radio stations  
Scanning the preset radio stations  
Press and hold or  
3
until you hear a beep.  
Preset stations will be played for 5 seconds each.  
When the desired station is reached, press the button once  
again.  
Scanning all radio stations within range  
Press  
or  
.
All stations with reception will be played for 5 seconds each.  
When the desired station is reached, press the button once  
again.  
169  
3-2. Using the audio system  
When the battery is disconnected  
Stations presets are erased.  
Reception sensitivity  
Maintaining perfect radio reception at all times is difficult due to the con-  
tinually changing position of the antenna, differences in signal strength  
and surrounding objects, such as trains, transmitters, etc.  
The radio antenna is mounted inside the rear window. To maintain clear  
radio reception, do not attach metallic window tinting or other metallic  
objects to the antenna wire mounted inside the rear window.  
170