Get Maintenanceandcare Guide for Toyota Yaris 4 Door Third Generation (2011-2020)

315

Maintenance and care

7

7-1. Maintenance and care

7-3. Do-it-yourself maintenance

Cleaning and protecting

the vehicle exterior ..........316

Do-it-yourself service

precautions......................325

Cleaning and protecting

the vehicle interior ...........319

Hood ..................................328

Positioning a floor jack.......330

Engine compartment..........332

Tires...................................347

Tire inflation pressure ........360

Wheels...............................362

Air conditioning filter ..........365

7-2. Maintenance

Maintenance

requirements....................322

Wireless remote control/

electronic key battery.......367

Checking and replacing

fuses................................370

Light bulbs .........................376

316

7-1. Maintenance and care

Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in

prime condition:

 Working from top to bottom, liberally apply water to the vehicle

body, wheel wells and underside of the vehicle to remove any dirt

and dust.

 Wash the vehicle body using a sponge or soft cloth, such as a

chamois.

 For hard-to-remove marks, use car wash soap and rinse thoroughly

with water.

 Wipe away any water.

 Wax the vehicle when the waterproof coating deteriorates.

If water does not bead on a clean surface, apply wax when the vehicle

body is cool.

 Automatic car washes

 Fold the mirrors and remove the antenna before washing the vehicle. Start

washing from the front of the vehicle. Make sure to re-install the antenna

and extend the mirrors before driving.

 Brushes used in automatic car washes may scratch the vehicle surface and

harm your vehicle’s paint.

 Rear spoiler (if equipped) may not be washable in some automatic car

washes. There may also be an increased risk of damage to vehicle.

 High pressure car washes

 Do not allow the nozzles of the car wash to come within close proximity of

the windows and door borders, and high mounted stoplight.

 Before using the car wash, check that the fuel filler door on your vehicle is

closed properly.

 When using a car wash (vehicles with a smart entry & start system)

If the door handle becomes wet while the electronic key is within the effective

range, the door may lock and unlock repeatedly. Place the key in a position

2 m (6 ft.) or more separate from the vehicle while the vehicle is being

washed. (Take care to ensure that the key is not stolen.)

317

7-1. Maintenance and care

 Aluminum wheels (if equipped)

 Remove any dirt immediately by using a neutral detergent. Do not use hard

brushes or abrasive cleaners. Do not use strong or harsh chemical clean-

ers.

Use the same mild detergent and wax as used on the paint.

 Do not use detergent on the wheels when they are hot, for example after

driving for long distance in the hot weather.

 Wash detergent from the wheels immediately after use.

 To preserve the wheels luster, do not allow hot water, such as from steam

cleaning, to contact them directly.

 Bumpers

Do not scrub with abrasive cleaners.

WARNING

When cleaning the windshield (vehicles with a rain-sensing windshield

wiper)

Set the wiper switch to off.

Off

If the wiper switch is in “AUTO”, the wiper

may operate unexpectedly in the follow-

ing situations, and may result in hands

being caught or other serious injuries and

cause damage to the wiper blades.

 When the upper part of the windshield where the raindrop sensor is

located is touched by hand

7

 When a wet rag or similar is held close to the raindrop sensor

 If something bumps against the windshield

 If you directly touch the raindrop sensor body or if something bumps into

the raindrop sensor

When washing the vehicle

Do not apply water to the inside of the engine compartment. Doing so may

cause the electrical components etc. to catch fire.

Precautions regarding the exhaust pipes

Exhaust gases cause the exhaust pipes to become quite hot.

When washing the vehicle, be careful not to touch the pipes until they have

cooled sufficiently, as touching hot exhaust pipes can cause burns.

318

7-1. Maintenance and care

NOTICE

To prevent paint deterioration and corrosion on the body and compo-

nents (aluminum wheels etc.)

 Wash the vehicle immediately in the following cases:

• After driving near the sea coast

• After driving on salted roads

• If coal tar or tree sap is present on the paint surface

• If dead insects, insect droppings or bird droppings are present on the

paint surface

• After driving in an area contaminated with soot, oily smoke, mine dust,

iron powder or chemical substances

• If the vehicle becomes heavily soiled with dust or mud

• If liquids such as benzene and gasoline are spilled on the paint surface

 If the paint is chipped or scratched, have it repaired immediately.

 To prevent the wheels from corroding, remove any dirt and store in a place

with low humidity when storing the wheels.

Cleaning the exterior lights

 Wash carefully. Do not use organic substances or scrub with a hard brush.

This may damage the surfaces of the lights.

 Do not apply wax to the surfaces of the lights.

Wax may cause damage to the lenses.

Antenna installation and removal precautions

 Before driving, ensure that the antenna is installed.

 When the antenna is removed, such as before entering an automatic car

wash, make sure to store it in a suitable place so as not to lose it. Also,

before driving, make sure to reinstall the antenna in its original position.

When using an automatic car wash (vehicles with a rain-sensing wind-

shield wiper)

Set the wiper switch to the off position.

If the wiper switch is in “AUTO”, the wiper may operate and the wiper blade

may be damaged.

To prevent damage to the antenna

Remove the antenna in the following situations:

 When the antenna will touch the ceiling of a garage or other such places

 When a car cover is to be used to cover the vehicle

319

7-1. Maintenance and care

Cleaning and protecting the vehicle interior

The following procedures will help protect your vehicle’s interior

and keep it in top condition:

Protecting the vehicle interior

Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces

with a cloth dampened with lukewarm water.

Cleaning the leather areas

 Remove dirt and dust using a vacuum cleaner.

 Wipe off any excess dirt and dust with a soft cloth dampened with

diluted detergent.

Use a diluted water solution of approximately 5% neutral wool detergent.

 Wring out any excess water from the cloth and thoroughly wipe off

all remaining traces of detergent.

 Wipe the surface with a dry, soft cloth to remove any remaining

moisture. Allow the leather to dry in a shaded and ventilated area.

Cleaning the synthetic leather areas

 Remove loose dirt using a vacuum cleaner.

 Apply a mild soap solution to the synthetic leather using a sponge

or soft cloth.

7

 Allow the solution to soak in for a few minutes. Remove the dirt and

wipe off the solution with a clean, damp cloth.

320

7-1. Maintenance and care

 Caring for leather areas

Toyota recommends cleaning the interior of the vehicle at least twice a year to

maintain the quality of the vehicle’s interior.

 Shampooing the carpets

There are several commercial foaming-type cleaners available. Use a sponge

or brush to apply the foam. Rub in overlapping circles. Do not use water.

Wipe dirty surfaces and let them dry. Excellent results are obtained by keep-

ing the carpet as dry as possible.

 Seat belts

Clean with mild soap and lukewarm water using a cloth or sponge. Also

check the belts periodically for excessive wear, fraying or cuts.

WARNING

Water in the vehicle

 Do not splash or spill liquid in the vehicle.

Doing so may cause electrical components, etc. to malfunction or catch

fire.

 Do not get any of the SRS components or wiring in the vehicle interior wet.

(P. 38)

An electrical malfunction may cause the airbags to deploy or not function

properly, resulting in death or serious injury.

Cleaning the interior (especially instrument panel)

Do not use polish wax or polish cleaner. The instrument panel may reflect

off the windshield, obstructing the driver’s view and leading to an accident,

resulting in death or serious injury.

321

7-1. Maintenance and care

NOTICE

Cleaning detergents

 Do not use the following types of detergent, as they may discolor the vehi-

cle interior or cause streaks or damage to painted surfaces:

• Non-seat portions: Organic substances such as benzene or gasoline,

alkaline or acidic solutions, dye, and bleach

• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco-

hol

 Do not use polish wax or polish cleaner. The instrument panel’s or other

interior part’s painted surface may be damaged.

Preventing damage to leather surfaces

Observe the following precautions to avoid damage to and deterioration of

leather surfaces:

 Remove any dust or dirt from leather surfaces immediately.

 Do not expose the vehicle to direct sunlight for extended periods of time.

Park the vehicle in the shade, especially during summer.

 Do not place items made of vinyl, plastic, or containing wax on the uphol-

stery, as they may stick to the leather surface if the vehicle interior heats

up significantly.

Water on the floor

Do not wash the vehicle floor with water.

Vehicle systems such as the audio system may be damaged if water comes

into contact with electrical components such as the audio system above or

under the floor of the vehicle. Water may also cause the body to rust.

Cleaning the inside of the rear window

7

 Do not use glass cleaner to clean the rear window, as this may cause

damage to the rear window defogger heater wires. Use a cloth dampened

with lukewarm water to gently wipe the window clean. Wipe the window in

strokes running parallel to the heater wires.

 Be careful not to scratch or damage the heater wires.

322

7-2. Maintenance

Maintenanc e requirem ents

To ensure safe and economical driving, day-to-day care and reg-

ular maintenance are essential. Toyota recommends the follow-

ing maintenance:

Scheduled maintenance

Scheduled maintenance should be performed at specified intervals

according to the maintenance schedule.

For full details of your maintenance schedule, refer to the “Toyota Service

Booklet” or “Toyota Warranty Booklet”.

Do-it-yourself maintenance

What about do-it-yourself maintenance?

Many of the maintenance items are easy to do yourself if you have a little

mechanical ability and a few basic automotive tools.

Note, however, that some maintenance tasks require special tools and

skills. These are best performed by qualified technicians. Even if you are

an experienced do-it-yourself mechanic, we recommend that repairs and

maintenance be conducted by any authorized Toyota dealer or repairer, or

another duly qualified and equipped professional. Any authorized Toyota

dealer or repairer will keep a record of maintenance, which could be useful

should you ever require Warranty Service. Should you choose to select a

qualified and equipped professional other than an authorized Toyota

repairer to service or maintain your vehicle, we recommend that you

request that a record of maintenance be kept.

323

7-2. Maintenance

 Where to go for the maintenance service?

In order to maintain your vehicle in the best possible condition, Toyota recom-

mends that all repairs and service operations be carried out by authorized

Toyota dealers or repairers or other duly qualified and equipped profession-

als. For repairs and services covered by your warranty, please visit an autho-

rized Toyota dealer or repairer, who will use genuine Toyota parts in repairing

any difficulties you may encounter. There can also be advantages in utilizing

authorized Toyota dealers or repairers for non-warranty repairs and services,

as members of the Toyota network will be able to expertly assist you with any

difficulties you may encounter.

Your Toyota dealer or repairer, or another duly qualified and equipped profes-

sional will perform all of the scheduled maintenance on your vehicle reliably

and economically due to their experience with Toyota vehicles.

 Does your vehicle need repairs?

Be on the alert for changes in performance and sounds, and visual tip-offs

that indicate service is needed. Some important clues are:

 Engine misfire, stumbling or pinging

 Appreciable loss of power

 Strange engine noises

 A fluid leak under the vehicle (However, water dripping from the air condi-

tioning system after use is normal.)

 Change in exhaust sound (This may indicate a dangerous carbon monoxide

leak. Drive with the windows open and have the exhaust system checked

immediately.)

 Flat-looking tires, excessive tire squeal when cornering, uneven tire wear

 Vehicle pulls to one side when driven straight on a level road

 Strange noises related to suspension movement

7

 Loss of brake effectiveness, spongy feeling brake pedal or clutch pedal

(vehicles with a manual transmission), pedal almost touches the floor, vehi-

cle pulls to one side when braking

 Engine coolant temperature continually higher than normal

If you notice any of these clues, take your vehicle to any authorized Toyota

dealer or repairer, or another duly qualified and equipped professional as

soon as possible. Your vehicle may need adjustment or repair.

324

7-2. Maintenance

WARNING

If your vehicle is not properly maintained

Improper maintenance could result in serious damage to the vehicle and

possible death or serious injury.

Handling of the battery

Battery posts, terminals and related accessories contain lead and lead com-

pounds which are known to cause brain damage. Wash your hands after

handling. (P. 342)

325

7-3. Do-it-yourself maintenance

Do-it -yourself ser vic e prec autions

If you perform maintenance by yourself, be sure to follow the

correct procedure as given in these sections.

Items

Parts and tools

• Baking soda

• Warm water

• Grease

Battery condition

(P. 342)

• Conventional wrench (for terminal clamp bolts)

• Distilled water

• “Toyota Super Long Life Coolant” or a similar high

quality ethylene glycol-based non-silicate, non-

amine, non-nitrite and non-borate coolant with long-

life hybrid organic acid technology

“Toyota Super Long Life Coolant” is pre-mixed with

50% coolant and 50% deionized water.

• Funnel (used only for adding coolant)

Engine coolant

level (P. 340)

• “Toyota Genuine Motor Oil” or equivalent

• Rag or paper towel

• Funnel (used only for adding engine oil)

Engine oil level

(P. 335)

Fuses

(P. 370)

• Fuse with same amperage rating as original

• Bulb with same number and wattage rating as origi-

nal

• Phillips-head screwdriver

Light bulbs

(P. 376)

7

• Flathead screwdriver

• Wrench

Radiator, condenser

and intercooler

(P. 341)



Tire inflation

pressure

(P. 360)

• Tire pressure gauge

• Compressed air source

• Water or washer fluid containing antifreeze (for win-

ter use)

• Funnel (used only for adding water or washer fluid)

Washer fluid

(P. 345)

326

7-3. Do-it-yourself maintenance

WARNING

The engine compartment contains many mechanisms and fluids that may

move suddenly, become hot, or become electrically energized. To avoid death

or serious injury, observe the following precautions.

When working on the engine compartment

 Keep hands, clothing and tools away from the moving fan and engine

drive belt.

 Be careful not to touch the engine, radiator, exhaust manifold, etc. right

after driving as they may be hot. Oil and other fluids may also be hot.

 Do not leave anything that may burn easily, such as paper and rags, in the

engine compartment.

 Do not smoke, cause sparks or expose an open flame to fuel on the bat-

tery. Fuel and battery fumes are flammable.

 Be extremely cautious when working on the battery. It contains poisonous

and corrosive sulfuric acid.

 Take care because brake fluid can harm your hands or eyes and damage

painted surfaces. If fluid gets on your hands or in your eyes, flush the

affected area with clean water immediately.

If you still experience discomfort, consult a doctor.

When working near the electric cooling fan or radiator grille

 Vehicles without a smart entry & start system

Be sure the engine switch is in the “LOCK” position.

With the engine switch in the “ON” position, the electric cooling fan may

automatically start to run if the air conditioning is on and/or the coolant tem-

perature is high. (P. 341)

 Vehicles with a smart entry & start system

Be sure the engine switch is off.

With the engine switch in IGNITION ON mode, the electric cooling fan may

automatically start to run if the air conditioning is on and/or the coolant tem-

perature is high. (P. 341)

Safety glasses

Wear safety glasses to prevent flying or falling material, fluid spray, etc.

from getting in your eyes.

327

7-3. Do-it-yourself maintenance

NOTICE

If you remove the air cleaner filter

Driving with the air cleaner filter removed may cause excessive engine wear

due to dirt in the air.

If the fluid level is low or high

It is normal for the brake fluid level to go down slightly as the brake pads

wear or when the fluid level in the accumulator is high.

If the reservoir needs frequent refilling, it may indicate a serious problem.

7

328

7-3. Do-it-yourself maintenance

Hood

Release the lock from the inside of the vehicle to open the hood.

1

Pull the hood lock release lever.

The hood will pop up slightly.

2

Pull up the auxiliary catch lever

and lift the hood.

3

Hold the hood open by inserting

the supporting rod into the slot.

329

7-3. Do-it-yourself maintenance

WARNING

Pre-driving check

Check that the hood is fully closed and locked.

If the hood is not locked properly, it may open while the vehicle is in motion

and cause an accident, which may result in death or serious injury.

When opening the hood

Make sure to use the support rod to support the hood when opening it,

ensuring that the rod is fixed correctly. The hood may stay open without

support on slope, however, it is dangerous because the hood may suddenly

close.

NOTICE

When closing the hood

Be sure to return the support rod to its clip before closing the hood. Closing

the hood without returning the support rod properly could cause the hood to

bend.

7

330

7-3. Do-it-yourself maintenance

Posit ioning a floor jack

When using a floor jack, follow the instructions in the manual

provided with the jack and perform the operation safely.

When raising your vehicle with a floor jack, position the jack cor-

rectly. Improper placement may damage your vehicle or cause

injury.

Front

Rear

331

7-3. Do-it-yourself maintenance

NOTICE

When raising your vehicle

Do not jack the vehicle at the suspen-

sion. The suspension may be damaged.

Suspension

Front

7

332

7-3. Do-it-yourself maintenance

Engine c om partm ent

 1KR-FE engine

1

5

Fuse boxes

(P. 370)

Engine oil level dipstick

(P. 335)

Engine coolant reservoir

(P. 340)

2

3

4

6

7

8

9

Electric cooling fan

Condenser

Engine oil filler cap

(P. 341)

(P. 337)

(P. 342)

Radiator

Battery

Washer fluid tank (P. 345)

333

7-3. Do-it-yourself maintenance

 1NR-FE engine

1

5

Fuse boxes

(P. 370)

(P. 337)

Engine coolant reservoir

(P. 340)

2

Engine oil filler cap

6

7

8

9

Electric cooling fan

Condenser

3

Engine oil level dipstick

(P. 335)

(P. 342)

(P. 341)

Radiator

7

4

Battery

Washer fluid tank (P. 345)

334

7-3. Do-it-yourself maintenance

 1ND-TV engine

D

1

2

6

7

Fuse boxes

(P.370)

(P. 337)

Intercooler

(P. 341)

Engine oil filler cap

Electric cooling fan

Condenser

8

(P. 341)

3

Engine oil level dipstick

(P. 335)

9

Radiator

10

Engine coolant reservoir

(P. 340)

Washer fluid tank (P. 345)

4

5

Fuel filter

Battery

(P. 346)

(P. 342)

11

335

7-3. Do-it-yourself maintenance

Engine oil

With the engine at operating temperature and turned off, check the oil

level on the dipstick.

 Checking the engine oil

1

Park the vehicle on level ground. After warming up the engine

and turning it off, wait more than 5 minutes for the oil to drain

back into the bottom of the engine.

2

Holding a rag under the end, pull the dipstick out.

 1KR-FE engine

 1NR-FE engine

 1ND-TV engine

7

3

Wipe the dipstick clean.

4

Reinsert the dipstick fully.

336

7-3. Do-it-yourself maintenance

5

Holding a rag under the end, pull the dipstick out and check the

oil level.

Low

1

Normal

2

Excessive

3

 Flat dipstick

 Non-flat dipstick

The shape of the dipstick may differ depending on the type of

vehicle or engine.

6

Wipe the dipstick and reinsert it fully.

337

7-3. Do-it-yourself maintenance

 Adding engine oil

If the oil level is below or near the low level mark, add engine oil of

the same type as that already in the engine.

 1KR-FE engine

 1NR-FE engine

 1ND-TV engine

7

Make sure to check the oil type and prepare the items needed

before adding oil.

Engine oil selection

P. 474

 1KR-FE engine

1.3 L (1.4 qt., 1.1 lmp.qt.)

Oil quantity

(Low  Full)

 1NR-FE and 1ND-TV engines

1.5 L (1.6 qt., 1.3 lmp.qt.)

Clean funnel

Items

1

Remove the oil filler cap by turning it counterclockwise.

Add engine oil slowly, checking the dipstick.

Install the oil filler cap by turning it clockwise.

2

3

338

7-3. Do-it-yourself maintenance

 Engine oil consumption

A certain amount of engine oil will be consumed while driving. In the following

situations, oil consumption may increase, and engine oil may need to be

refilled in between oil maintenance intervals.

 When the engine is new, for example directly after purchasing the vehicle or

after replacing the engine

 If low quality oil or oil of an inappropriate viscosity is used

 When driving at high engine speeds or with a heavy load, when towing

(except for South Africa), or when driving while accelerating or decelerating

frequently

 When leaving the engine idling for a long time, or when driving frequently

through heavy traffic

 After changing the engine oil (diesel engine only)

The engine oil maintenance data should be reset. Perform the following pro-

cedures:

1

Switch the display to the trip meter “A” when the engine is running.

(P. 91)

2

Turn the engine switch to the “LOCK” position (vehicles without a smart

entry & start system) or off (vehicles with a smart entry & start system).

3

Vehicles without a smart entry & start system:

While pressing the display change button (P. 91), turn the engine

switch to the “ON” position (do not start the engine because reset mode

will be canceled). Continue to press and hold the button until the trip

meter displays “000000”.

Vehicles with a smart entry & start system:

While pressing the display change button (P. 91), turn the engine

switch to the IGNITION ON mode (do not start the engine because other-

wise the reset mode will be canceled). Continue to press and hold the

button until the trip meter displays “000000”.

339

7-3. Do-it-yourself maintenance

WARNING

Used engine oil

 Used engine oil contains potentially harmful contaminants which may

cause skin disorders such as inflammation and skin cancer, so care

should be taken to avoid prolonged and repeated contact. To remove used

engine oil from your skin, wash thoroughly with soap and water.

 Dispose of used oil and filters only in a safe and acceptable manner. Do

not dispose of used oil and filters in household trash, in sewers or onto the

ground.

Call any authorized Toyota dealer or repairer, or another duly qualified and

equipped professional, service station or auto parts store for information

concerning recycling or disposal.

 Do not leave used engine oil within the reach of children.

NOTICE

To prevent serious engine damage

Check the oil level on a regular basis.

When replacing the engine oil

 Be careful not to spill engine oil on the vehicle components.

 Avoid overfilling, or the engine could be damaged.

 Check the oil level on the dipstick every time you refill the vehicle.

 Be sure the engine oil filler cap is properly tightened.

Engine oil (vehicles with a DPF system*)

7

Using an engine oil other than ACEA C2 may damage the catalytic con-

verter.

*: To determine whether or not your vehicle has a DPF system, contact any

authorized Toyota dealer or repairer, or another duly qualified and equipped

professional.

340

7-3. Do-it-yourself maintenance

Engine coolant

The coolant level is satisfactory if it is between the “FULL” and “LOW”

lines on the reservoir when the engine is cold.

 Gasoline engine

 Diesel engine

1

Reservoir cap

2

“FULL” line

3

“LOW” line

If the level is on or below the “LOW” line, add coolant up to the “FULL”

line. (P. 458)

 Coolant selection

Only use “Toyota Super Long Life Coolant” or a similar high quality ethylene

glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with

long-life hybrid organic acid technology.

“Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion-

ized water. (Minimum temperature: -35C [-31F])

For more details about coolant, contact any authorized Toyota dealer or

repairer, or another duly qualified and equipped professional.

 If the coolant level drops within a short time of replenishing

Visually check the radiator, hoses, engine coolant reservoir caps, drain cock

and water pump.

If you cannot find a leak, have any authorized Toyota dealer or repairer, or

another duly qualified and equipped professional test the cap and check for

leaks in the cooling system.

341

7-3. Do-it-yourself maintenance

WARNING

When the engine is hot

Do not remove the radiator cap (gasoline engine), or the engine coolant res-

ervoir cap (diesel engine).

The cooling system may be under pressure and may spray hot coolant if the

cap is removed, causing serious injuries, such as burns.

NOTICE

When adding coolant

Coolant is neither plain water nor straight antifreeze. The correct mixture of

water and antifreeze must be used to provide proper lubrication, corrosion

protection and cooling. Be sure to read the antifreeze or coolant label.

If you spill coolant

Be sure to wash it off with water to prevent it from damaging parts or paint.

Radiator, condenser and intercooler

Check the radiator, condenser and intercooler and clear away any for-

eign objects.

If any of the above parts is extremely dirty or you are not sure of their

condition, have your vehicle inspected by any authorized Toyota

dealer or repairer, or another duly qualified and equipped profes-

sional.

7

WARNING

When the engine is hot

Do not touch the radiator, condenser or intercooler as they may be hot and

cause serious injuries, such as burns.

342

7-3. Do-it-yourself maintenance

Battery

Check the battery as follows.

 Caution symbols

The meanings of each caution symbol on the top of the battery are

as follows:

No smoking, no naked

Battery acid

flames, no sparks

Note operating instruc-

Shield eyes

tions

Keep away from children

Explosive gas

 Battery exterior

Make sure that the battery terminals are not corroded and that

there are no loose connections, cracks, or loose clamps.

1

Terminals

2

Hold-down clamp

343

7-3. Do-it-yourself maintenance

 Before recharging

When recharging, the battery produces hydrogen gas which is flammable and

explosive. Therefore, observe the following before recharging:

 If recharging with the battery installed on the vehicle, be sure to disconnect

the ground cable.

 Make sure the power switch on the charger is off when connecting and dis-

connecting the charger cables to the battery.

 After recharging/reconnecting the battery (vehicles with a smart entry &

start system)

 Unlocking the doors using the smart entry & start system may not be possi-

ble immediately after reconnecting the battery. If this happens, use the wire-

less remote control or the mechanical key to lock/unlock the doors.

 Start the engine with the engine switch in ACCESSORY mode. The engine

may not start with the engine switch turned off. However, the engine will

operate normally from the second attempt.

 The engine switch mode is recorded by the vehicle. If the battery is recon-

nected, the vehicle will return the engine switch mode to the status it was in

before the battery was disconnected. Make sure to turn off the engine

before disconnect the battery. Take extra care when connecting the battery

if the engine switch mode prior to discharge is unknown.

If the engine will not start even after multiple attempts, contact any authorized

Toyota dealer or repairer, or another duly qualified and equipped professional.

WARNING

Chemicals in the battery

7

Batteries contain poisonous and corrosive sulfuric acid and may produce

hydrogen gas which is flammable and explosive. To reduce the risk of death

or serious injury, take the following precautions while working on or near the

battery:

 Do not cause sparks by touching the battery terminals with tools.

 Do not smoke or light a match near the battery.

 Avoid contact with eyes, skin and clothes.

 Never inhale or swallow electrolyte.

 Wear protective safety glasses when working near the battery.

 Keep children away from the battery.

344

7-3. Do-it-yourself maintenance

WARNING

Where to safely charge the battery

Always charge the battery in an open area. Do not charge the battery in a

garage or closed room where there is insufficient ventilation.

How to recharge the battery

Only perform a slow charge (5 A or less). The battery may explode if

charged at a quicker rate.

Emergency measures regarding electrolyte

 If electrolyte gets in your eyes

Flush your eyes with clean water for at least 15 minutes and get immedi-

ate medical attention. If possible, continue to apply water with a sponge or

cloth while traveling to the nearest medical facility.

 If electrolyte gets on your skin

Wash the affected area thoroughly. If you feel pain or burning, get medical

attention immediately.

 If electrolyte gets on your clothes

It can soak through clothing on to your skin. Immediately take off the cloth-

ing and follow the procedure above if necessary.

 If you accidentally swallow electrolyte

Drink a large quantity of water or milk. Get emergency medical attention

immediately.

NOTICE

When recharging the battery

Never recharge the battery while the engine is running. Also, be sure all

accessories are turned off.

345

7-3. Do-it-yourself maintenance

Washer fluid

If the washer fluid level is less

than “FULL” line, add washer fluid

to “FULL” line.

WARNING

When adding washer fluid

Do not add washer fluid when the engine is hot or running as washer fluid

contains alcohol and may catch fire if spilled on the engine etc.

NOTICE

Do not use any fluid other than washer fluid

Do not use soapy water or engine antifreeze instead of washer fluid.

Doing so may cause streaking on the vehicle’s painted surfaces.

Diluting washer fluid

Dilute washer fluid with water as necessary.

Refer to the freezing temperatures listed on the label of the washer fluid bot-

tle.

7

346

7-3. Do-it-yourself maintenance

Fuel filter (diesel engine)

You may drain the fuel filter yourself. However, as the operation is dif-

ficult, we recommend having it drained by any authorized Toyota

dealer or repairer, or another duly qualified and equipped profes-

sional. Even if you decide to drain it yourself, contact any authorized

Toyota dealer or repairer, or another duly qualified and equipped pro-

fessional.

The water in the fuel filter needs to be drained if the fuel filter warning

light comes on. (P. 407)

1

Turn the engine switch to the “LOCK” position (vehicles without a

smart entry & start system) or off (vehicles with a smart entry & start

system).

2

Place a small tray under the drain plug to catch the water and any

fuel that comes out.

3

Turn the drain plug counter-

clockwise about 2 to 2 1/2

turns.

4

Operate the priming pump until

fuel begins to run out.

5

After draining, tighten the drain plug by hand.

347

7-3. Do-it-yourself maintenance

Tires

Replace or rotate tires in accordance with maintenance sched-

ules and treadwear.

Checking tires

1

New tread

2

Treadwear indicator

3

Worn tread

The location of treadwear indica-

tors is shown by the “TWI” or “”

marks, etc., molded on the sidewall

of each tire.

Check spare tire condition and

pressure if not rotated.

Tire rotation

Rotate the tires in the order shown.

 Vehicles with a spare tire of dif-  Vehicles with a spare tire of

ferent wheel type from the

installed tires or an emergency

tire puncture repair kit

the same wheel type as the

installed tires

7

Front

348

7-3. Do-it-yourself maintenance

To equalize tire wear and help extend tire life, Toyota recommends

that tire rotation is carried out approximately every 10000 km (6000

miles).

Tire pressure warning system (if equipped)

Your vehicle is equipped with a tire pressure warning system that uses

tire pressure warning valves and transmitters to detect low tire infla-

tion pressure before serious problems arise.

If the tire pressure drops below a predetermined level, the driver is

warned by a warning light. (P. 408)

Installing tire pressure warning valves and transmitters (vehicles

with a tire pressure warning system)

When replacing tires or wheels, tire pressure warning valves and

transmitters must also be installed.

When new tire pressure warning valves and transmitters are installed,

new ID codes must be registered in the tire pressure warning com-

puter and the tire pressure warning system must be initialized. Have

tire pressure warning valve and transmitter ID codes registered by

any authorized Toyota dealer or repairer, or another duly qualified and

equipped professional. (P. 350)

Initializing the tire pressure warning system (vehicles with a tire

pressure warning system)

 The tire pressure warning system must be initialized in the fol-

lowing circumstances:

 When rotating front and rear tires which have different tire infla-

tion pressures

 When the tire inflation pressure is changed such as when chang-

ing traveling speed

 When changing the tire size

When the tire pressure warning system is initialized, the current tire

inflation pressure is set as the benchmark pressure.

349

7-3. Do-it-yourself maintenance

 How to initialize the tire pressure warning system (vehicles

with a tire pressure warning system)

1

Park the vehicle in a safe place and turn the engine switch to the

“LOCK” position (vehicles without a smart entry & start system)

or off (vehicles with a smart entry & start system).

Initialization cannot be performed while the vehicle is moving.

2

Adjust the tire inflation pressure to the specified cold tire inflation

pressure level. (P. 483)

Make sure to adjust the tire pressure to the specified cold tire inflation

pressure level. The tire pressure warning system will operate based on

this pressure level.

3

Turn the engine switch to the “ON” position (vehicles without a

smart entry & start system) or IGNITION ON mode (vehicles with

a smart entry & start system).

4

Press and hold the tire pres-

sure warning reset switch

until the tire pressure warn-

ing light blinks slowly 3 times.

5

Vehicles without a smart entry & start system: Wait for a few min-

7

utes with the engine switch in the “ON” position and then turn the

engine switch to the “ACC” or “LOCK” position.

Vehicles with a smart entry & start system: Wait for a few minutes

with the engine switch in IGNITION ON mode and then turn the

engine switch off.

350

7-3. Do-it-yourself maintenance

Registering ID codes (vehicles with a tire pressure warning sys-

tem)

The tire pressure warning valve and transmitter is equipped with a

unique ID code. When replacing a tire pressure warning valve and

transmitter, it is necessary to register the ID code. Have the ID code

registered by any authorized Toyota dealer or repairer, or another duly

qualified and equipped professional.

 When to replace your vehicle’s tires

Tires should be replaced if:

 You have tire damage such as cuts, splits, cracks deep enough to expose

the fabric, and bulges indicating internal damage

 A tire goes flat repeatedly or cannot be properly repaired due to the size or

location of a cut or other damage

If you are not sure, consult with any authorized Toyota dealer or repairer, or

another duly qualified and equipped professional.

 Replacing tire and wheels (vehicles with a tire pressure warning system)

If the ID code of the tire pressure warning valve and transmitter is not regis-

tered, the tire pressure warning system will not work properly. After driving for

about 10 minutes, the tire pressure warning light blinks for 1 minute and stays

on to indicate a system malfunction.

 Tire life

Any tire over 6 years old must be checked by a qualified technician even if it

has seldom or never been used or damage is not obvious.

 Low profile tires (vehicles with 195/50R16 tires)

Generally, low profile tires will wear more rapidly and tire grip performance

will be reduced on snowy and/or icy roads when compared to standard tires.

Be sure to use snow tires or tire chains on snowy and/or icy roads and drive

carefully at a speed appropriate for road and weather conditions.

351

7-3. Do-it-yourself maintenance

 Routine tire inflation pressure checks (vehicles with a tire pressure

warning system)

The tire pressure warning system does not replace routine tire inflation pres-

sure checks. Make sure to check tire inflation pressure as part of your routine

of daily vehicle checks.

 Initializing the tire pressure warning system (vehicles with a tire pres-

sure warning system)

Initialize the system with the tire inflation pressure adjusted to the specified

level.

 If the tread on snow tires wears down below 4 mm (0.16 in.)

The effectiveness of the tires as snow tires is lost.

 When initialization of the tire pressure warning system has failed (vehi-

cles with a tire pressure warning system)

Initialization can be completed in a few minutes. However, in the following

cases, the settings have not been recorded and the system will not operate

properly. If repeated attempts to record tire inflation pressure settings are

unsuccessful, have the vehicle inspected by any authorized Toyota dealer or

repairer, or another duly qualified and equipped professional.

 When operating the tire pressure warning reset switch, the tire pressure

warning light does not blink 3 times.

 After driving for a certain period of time since the initialization has been

completed, the warning light comes on after blinking for 1 minute.

7

352

7-3. Do-it-yourself maintenance

 Certification for the tire pressure warning system

The latest “DECLARATION of CONFORMITY” (DoC) is available at the fol-

lowing address:

http://www.globaldenso.com/en/products/oem/index.html

353

7-3. Do-it-yourself maintenance

7

354

7-3. Do-it-yourself maintenance

355

7-3. Do-it-yourself maintenance

The latest “DECLARATION of CONFORMITY” (DoC) is available at the fol-

lowing:

DoC address: http://www.pacific-ind.co.jp/eng/products/car/tpms/doc/

7

356

7-3. Do-it-yourself maintenance

357

7-3. Do-it-yourself maintenance

7

358

7-3. Do-it-yourself maintenance

WARNING

When inspecting or replacing tires

Observe the following precautions to prevent accidents.

Failure to do so may cause damage to parts of the drive train as well as

dangerous handling characteristics, which may lead to an accident resulting

in death or serious injury.

 Do not mix tires of different makes, models or tread patterns.

Also, do not mix tires of remarkably different treadwear.

 Do not use tire sizes other than those recommended by Toyota.

 Do not mix differently constructed tires (radial, bias-belted or bias-ply

tires).

 Do not mix summer, all season and snow tires.

 Do not use tires that have been used on another vehicle.

Do not use tires if you do not know how they were used previously.

 Vehicles with a compact spare tire: Do not tow if your vehicle has a com-

pact spare tire installed.

When initializing the tire pressure warning system (vehicles with a tire

pressure warning system)

Do not operate the tire pressure warning reset switch without first adjusting

the tire inflation pressure to the specified level. Otherwise, the tire pressure

warning light may not come on even if the tire inflation pressure is low, or it

may come on when the tire inflation pressure is actually normal.

NOTICE

Repairing or replacing tires, wheels, tire pressure warning valves,

transmitters and tire valve caps (vehicles with a tire pressure warning

system)

 When removing or fitting the wheels, tires or the tire pressure warning

valves and transmitters, contact any authorized Toyota dealer or repairer,

or another duly qualified and equipped professional as the tire pressure

warning valves and transmitters may be damaged if not handled correctly.

 Make sure to install the tire valve caps. If the tire valve caps are not

installed, water could enter the tire pressure warning valves and the tire

pressure warning valves could be bound.

 When replacing tire valve caps, do not use tire valve caps other than those

specified. The cap may become stuck.

359

7-3. Do-it-yourself maintenance

NOTICE

To avoid damage to the tire pressure warning valves and transmitters

(vehicles with a tire pressure warning system)

When a tire is repaired with liquid sealants, the tire pressure warning valve

and transmitter may not operate properly. If a liquid sealant is used, contact

any authorized Toyota dealer or repairer, or another duly qualified and

equipped professional or other qualified service shop as soon as possible.

Make sure to replace the tire pressure warning valve and transmitter when

replacing the tire. (P. 348)

Driving on rough roads

Take particular care when driving on roads with loose surfaces or potholes.

These conditions may cause losses in tire inflation pressure, reducing the

cushioning ability of the tires. In addition, driving on rough roads may cause

damage to the tires themselves, as well as the vehicle’s wheels and body.

Low profile tires (vehicles with 195/50R16 tires)

Low profile tires may cause greater damage than usual to the tire wheel

when sustaining impact from the road surface. Therefore, pay attention to

the following:

 Be sure to use proper tire inflation pressure. If tires are under-inflated, they

may be damaged more severely.

 Avoid potholes, uneven pavement, curbs and other road hazards. Failure

to do so may lead to severe tire and wheel damage.

If tire inflation pressure of each tire becomes low while driving

Do not continue driving, or your tires and/or wheels may be ruined.

7

360

7-3. Do-it-yourself maintenance

Tire inflat ion pressure

Make sure to maintain proper tire inflation pressure. Tire infla-

tion pressure should be checked at least once per month. How-

ever, Toyota recommends that tire inflation pressure be checked

once every two weeks. (P. 483)

 Effects of incorrect tire inflation pressure

Driving with incorrect tire inflation pressure may result in the following:

 Reduced fuel efficiency

 Reduced driving comfort and tire life

 Reduced safety

 Damage to the drive train

If a tire needs frequent inflating, have it checked by any authorized Toyota

dealer or repairer, or another duly qualified and equipped professional.

 Instructions for checking tire inflation pressure

When checking tire inflation pressure, observe the following:

 Check only when the tires are cold.

If your vehicle has been parked for at least 3 hours or has not been driven

for more than 1.5 km or 1 mile, you will get an accurate cold tire inflation

pressure reading.

 Always use a tire pressure gauge.

The appearance of the tire can be misleading. In addition, tire inflation pres-

sure that is even just a few pounds off can affect ride quality and handling.

 Do not reduce tire inflation pressure after driving. It is normal for tire inflation

pressure to be higher after driving.

 Never exceed the vehicle capacity weight.

Passengers and luggage weight should be placed so that the vehicle is bal-

anced.

361

7-3. Do-it-yourself maintenance

WARNING

Proper inflation is critical to save tire performance

Keep your tires properly inflated. Otherwise, the following conditions may

occur and result in an accident causing death or serious injury:

 Excessive wear

 Uneven wear

 Poor handling

 Possibility of blowouts resulting from overheated tires

 Poor sealing of the tire bead

 Wheel deformation and/or tire separation

 A greater possibility of tire damage from road hazards

NOTICE

When inspecting and adjusting tire inflation pressure

Be sure to put the tire valve caps back on.

Without the valve caps, dirt or moisture could get into the valve and cause

air leakage, which could result in an accident. If the caps are lost, replace

them as soon as possible.

7

362

7-3. Do-it-yourself maintenance

Wheels

If a wheel is bent, cracked or heavily corroded, it should be

replaced. Otherwise, the tire may separate from the wheel or

cause a loss of handling control.

Wheel selection

When replacing wheels, care should be taken to ensure that they are

equivalent to those removed in load capacity, diameter, rim width and

inset*.

Replacement wheels are available at any authorized Toyota dealer or

repairer, or another duly qualified and equipped professional.

*: Conventionally referred to as “offset”.

Toyota does not recommend using the following:

 Wheels of different sizes or types

 Used wheels

 Bent wheels that have been straightened

Aluminum wheel precautions (if equipped)

 Use only Toyota wheel nuts and wrenches designed for use with

your aluminum wheels.

 When rotating, repairing or changing your tires, check that the

wheel nuts are still tight after driving 1600 km (1000 miles).

 Be careful not to damage the aluminum wheels when using tire

chains.

 Use only Toyota genuine balance weights or equivalent and use a

plastic or rubber hammer when balancing your wheels.

363

7-3. Do-it-yourself maintenance

 When removing the wheel ornament (vehicles with steel wheels and

emergency tire puncture repair kit)

Remove the wheel ornament using the

wheel cap clip.

 When replacing wheels (vehicles with a tire pressure warning system)

The wheels of your vehicle are equipped with tire pressure warning valves

and transmitters (except for spare tire [include compact spare tire]) that allow

the tire pressure warning system to provide advance warning in the event of a

loss in tire inflation pressure. Whenever wheels are replaced, tire pressure

warning valves and transmitters must be installed. (P. 348)

WARNING

When replacing wheels

 Do not use wheels that are a different size from those recommended in the

Owner’s Manual, as this may result in a loss of handling control.

 Never use an inner tube in a leaking wheel which is designed for a tube-

less tire. Doing so may result in an accident, causing death or serious

injury.

When installing the wheel nuts

7

 Be sure to install the wheel nuts with the

tapered ends facing inward. Installing

the nuts with the tapered ends facing

Tapered

portion

outward can cause the wheel to break

and eventually cause the wheel to come

off while driving, which could lead to an

accident resulting in death or serious

injury.

364

7-3. Do-it-yourself maintenance

WARNING

 Never use oil or grease on the wheel bolts or wheel nuts.

Oil and grease may cause the wheel nuts to be excessively tightened,

leading to bolt or disc wheel damage. In addition, the oil or grease can

cause the wheel nuts to loosen and the wheel may fall off, causing an acci-

dent and resulting in death or serious injury. Remove any oil or grease

from the wheel bolts or wheel nuts.

Use of defective wheels prohibited

Do not use cracked or deformed wheels.

Doing so could cause the tire to leak air during driving, possibly causing an

accident.

NOTICE

Replacing tire pressure warning valves and transmitters (vehicles with

a tire pressure warning system)

 Because tire repair or replacement may affect the tire pressure warning

valves and transmitters, make sure to have tires serviced by any autho-

rized Toyota dealer or repairer, or another duly qualified and equipped pro-

fessional or other qualified service shop. In addition, make sure to

purchase your tire pressure warning valves and transmitters at any autho-

rized Toyota dealer or repairer, or another duly qualified and equipped pro-

fessional.

 Ensure that only genuine Toyota wheels are used on your vehicle.

Tire pressure warning valves and transmitters may not work properly with

non-genuine wheels.

365

7-3. Do-it-yourself maintenance

Air c onditioning filter

The air conditioning filter must be changed regularly to maintain

air conditioning efficiency.

Removal method

1

Turn the engine switch to the “LOCK” position (vehicles without a

smart entry & start system) or off (vehicles with a smart entry & start

system).

2

3

4

Open the glove box and slide

off the damper.

Push in each side of the glove

box to disconnect the upper

claws.

7

Pull out the glove box and dis-

connect the lower claws.

366

7-3. Do-it-yourself maintenance

5

Remove the filter cover.

 Left-hand drive vehicles

 Right-hand drive vehicles

6

Remove the air conditioning fil-

ter and replace it with a new

one.

The “UP” marks shown on the fil-

ter should be pointing up.

 Checking interval

Inspect and replace the air conditioning filter according to the maintenance

schedule. In dusty areas or areas with heavy traffic flow, early replacement

may be required. (For scheduled maintenance information, please refer to the

“Toyota Service Booklet” or “Toyota Warranty Booklet”.)

 If air flow from the vents decreases dramatically

The filter may be clogged. Check the filter and replace if necessary.

NOTICE

When using the air conditioning system

Make sure that a filter is always installed.

Using the air conditioning system without a filter may cause damage to the

system.

367

7-3. Do-it-yourself maintenance

Wireless rem ote c ontrol/elec tronic key bat-



ter y

Replace the battery with a new one if it is depleted.

You will need the following items:

 Flathead screwdriver

 Lithium battery CR2016 (vehicles without a smart entry & start sys-

tem), or CR2032 (vehicles with a smart entry & start system)

Replacing the battery

 Vehicles without a smart entry & start system

1

Lift the cover.

Insert the screw driver in the slot

and push down.

To prevent damage to the key,

cover the tip of the screwdriver with

a tape.

2

Remove the cover.

7

Insert the screw driver in the bot-

tom of the key and push down.

: If equipped

368

7-3. Do-it-yourself maintenance

3

Remove the depleted battery.

Insert a new battery with the “+”

terminal facing up.

 Vehicles with a smart entry & start system

1

Take out the mechanical key.

2

Remove the cover.

To prevent damage to the key,

cover the tip of the screwdriver with

a tape.

3

Remove the depleted battery.

Insert a new battery with the “+”

terminal facing up.

369

7-3. Do-it-yourself maintenance

 Use a CR2016 (vehicles without a smart entry & start system) or CR2032

(vehicles with a smart entry & start system) lithium battery

 Batteries can be purchased at any authorized Toyota dealer or repairer, or

another duly qualified and equipped professional, local electrical appliance

shops or camera stores.

 Replace only with the same or equivalent type recommended by the manu-

facturer.

 Dispose of used batteries according to local laws.

 If the key battery is depleted

The following symptoms may occur:

 The smart entry & start system (if equipped) and wireless remote control will

not function properly.

 The operational range will be reduced.

WARNING

Removed battery and other parts

These parts are small and if swallowed by a child, they can cause choking.

Keep away from children. Failure to do so could result in death or serious

injury.

Certification for the lithium battery

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT

TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUC-

TIONS

7

NOTICE

For normal operation after replacing the battery

Observe the following precautions to prevent accidents:

 Always work with dry hands.

Moisture may cause the battery to rust.

 Do not touch or move any other component inside the remote control.

 Do not bend either of the battery terminals.

370

7-3. Do-it-yourself maintenance

Check ing and replac ing fuses

If any of the electrical components do not operate, a fuse may

have blown. If this happens, check and replace the fuses as nec-

essary.

1

Turn the engine switch to the “LOCK” position (vehicles without a

smart entry & start system) or off (vehicles with a smart entry & start

system).

2

Open the fuse box cover.

 Engine compartment: type A and B fuse boxes

1

Type A fuse box

Push the tab in and lift the lid off.

2

Type B fuse box

Push the tab in and lift the lid off.

371

7-3. Do-it-yourself maintenance

 Engine compartment: type C fuse box (left-hand drive vehicles)

1

Pull the rubber strip on the

edge to unhook it from the

cover, and then push the

tabs in and lift the cover off.

2

Remove the battery terminal

cover and then the fuse box

cover.

 Engine compartment: type C fuse box (right-hand drive vehicles)

1

Pull the rubber strip on the

edge to unhook it from the

cover, and then push the

tabs in and lift the cover off.

7

2

Remove the battery terminal

cover and then the fuse box

cover.

372

7-3. Do-it-yourself maintenance

 Instrument panel (left-hand drive vehicles)

Remove the lid.

 Instrument panel (right-hand drive vehicles)

1

Remove the cover.

Do not pull off the cover using

excessive force as it is attached

to the footwell light.

2

Remove the lid.

3

Remove the fuse with the pull-

out tool.

Only type A fuse can be removed

using the pullout tool.

373

7-3. Do-it-yourself maintenance

4

Check if the fuse is blown.

1

Normal fuse

2

Blown fuse

From Type A to F:

Replace the blown fuse with a new fuse of an appropriate amperage rat-

ing. The amperage rating can be found on the fuse box lid.

Type G:

Contact any authorized Toyota dealer or repairer, or another duly qualified

and equipped professional.

 Type A

 Type B

 Type C

 Type D

7

374

7-3. Do-it-yourself maintenance

 Type E

 Type F

 Type G

 After a fuse is replaced

 If the lights do not turn on even after the fuse has been replaced, a bulb may

need replacement. (P. 376)

 If the replaced fuse blows again, have the vehicle inspected by any autho-

rized Toyota dealer or repairer, or another duly qualified and equipped pro-

fessional.

 If there is an overload in a circuit

The fuses are designed to blow, protecting the wiring harness from damage.

 When replacing light bulbs

Toyota recommends that you use genuine Toyota products designed for this

vehicle. Because certain bulbs are connected to circuits designed to prevent

overload, non-genuine parts or parts not designed for this vehicle may be

unusable.

375

7-3. Do-it-yourself maintenance

 When reinstalling the cover (type C fuse box)

 Left-hand drive vehicles

Reinstall the cover, and then hook the

rubber strip’s groove onto the cover.

 Right-hand drive vehicles

Reinstall the cover, and then hook the

rubber strip’s groove onto the cover.

WARNING

To prevent system breakdowns and vehicle fire

Observe the following precautions.

Failure to do so may cause damage to the vehicle, and possibly a fire or

injury.

 Never use a fuse of a higher amperage rating than that indicated, or use

any other object in place of a fuse.

7

 Always use a genuine Toyota fuse or equivalent.

Never replace a fuse with a wire, even as a temporary fix.

 Do not modify the fuses or fuse boxes.

NOTICE

Before replacing fuses

Have the cause of electrical overload determined and repaired by any

authorized Toyota dealer or repairer, or another duly qualified and equipped

professional as soon as possible.

376

7-3. Do-it-yourself maintenance

Light bulbs

You may replace the following bulbs by yourself. The difficulty

level of replacement varies depending on the bulb. As there is a

danger that components may be damaged, we recommend that

replacement is carried out by any authorized Toyota dealer or

repairer, or another duly qualified and equipped professional.

For more information about replacing other light bulbs, contact

any authorized Toyota dealer or repairer, or another duly quali-

fied and equipped professional.

Preparing for light bulb replacement

Check the wattage of the light bulb to be replaced. (P. 486)

Bulb locations

 Front

1

2

3

4

5

Front position lights/daytime

running lights (bulb type)

Front fog lights (if equipped)

Halogen headlights

Front turn signal lights

Side turn signal lights

377

7-3. Do-it-yourself maintenance

 Rear

Rear fog light*¹/

Rear turn signal lights

1

4

back-up light*²

5

Stop/tail lights (bulb type)

2

3

License plate lights

Back-up light*¹/

rear fog light*²

*¹: Left-hand drive vehicles

*²: Right-hand drive vehicles

7

378

7-3. Do-it-yourself maintenance

Replacing light bulbs

 Halogen headlights

 Reflector type

1

Unplug the connector.

2

Remove the rubber cover.

3

Release the bulb retaining

spring.

4

Remove the bulb.

To install a new bulb, align tabs

of the bulb with the cutouts of

the mounting hole.

379

7-3. Do-it-yourself maintenance

5

6

7

Set the new light bulb.

Align the 3 tabs on the light bulb

with the mounting and insert.

Install the bulb retaining

spring.

Install the rubber cover.

Ensure the rubber cover is

securely attached.

1

Fit the rubber cover outer

circumference in firmly.

2

Fit the rubber cover

7

around the light bulb in

until the light bulb plug can

be seen.

8

Install the connector.

380

7-3. Do-it-yourself maintenance

 Projector type

1

2

3

14

Turn the bulb base counter-

clockwise.

Pull the bulb out while press-

ing the lock release of the

connector.

Replace the light bulb, and

install the bulb base.

Align the 3 tabs on the light bulb

with the mounting and insert.

Turn and secure the bulb

base.

Shake the bulb base gently to

check that it is not loose, turn

the headlights on once and visu-

ally confirm that no light is leak-

ing through the mounting.

381

7-3. Do-it-yourself maintenance

 Front fog lights (if equipped)

1

Turn the steering wheel in

the opposite direction of the

light to be replaced.

Turn the steering wheel to a

point that allows your hand to

easily fit between the tire and

fender liner.

2

Remove the screw.

3

Partly remove the fender

liner until the bulb is visible.

7

4

Unplug the connector while

pressing the lock release.

382

7-3. Do-it-yourself maintenance

5

Turn the bulb base counter-

clockwise.

6

Set the new light bulb.

Align the 3 tabs on the light bulb

with the mounting, and insert.

7

Turn and secure the bulb.

8

Install the connector.

Shake the bulb base gently to

check that it is not loose, turn

the front fog light, on once and

visually confirm that no light is

leaking through the mounting.

383

7-3. Do-it-yourself maintenance

9

Reinstall the fender liner.

Attach the end of the fender liner

to the inside of the front bumper.

10

Install the screw.

 Front position lights/daytime running lights (bulb type)

1

Turn the bulb base counterclockwise.

 Type A

 Type B

7

384

7-3. Do-it-yourself maintenance

2

Remove the light bulb.

 Type A

 Type B

3

When installing, reverse the steps listed.

 Front turn signal lights

1

Turn the bulb base counterclockwise.

 Type A

 Type B

2

Remove the light bulb

 Type A

 Type B

3

When installing, reverse the steps listed.

385

7-3. Do-it-yourself maintenance

 Side turn signal lights

1

Depress the mirror.

2

Remove the mirror.

To prevent damaging the vehi-

cle, wrap the screwdriver with a

tape.

3

Remove the bulb base.

7

4

Remove the light bulb.

386

7-3. Do-it-yourself maintenance

5

After installing the new bulb,

secure the bulb base to the

mirror body.

6

Align the tabs, and secure

the mirror by pushing in each

diagonally-opposite pair of

tabs in order.

Make sure to insert the tabs in

order as shown in the illustra-

tion, and push them in until a

click is heard.

If you do not hear the click, do

not force the tabs in. Instead,

remove the mirror and check

that the tabs are aligned.

 Stop/tail lights (bulb type), and rear turn signal lights

1

Open the back door and

remove the cover.

To prevent damaging the vehi-

cle, wrap the screwdriver with a

tape.

2

Turn the bulb base counter-

clockwise.

1

Stop/tail light

2

Rear turn signal light

387

7-3. Do-it-yourself maintenance

3

4

5

6

Remove the light bulb.

1

Stop/tail light

2

Rear turn signal light

Install the new bulb.

1

Stop/tail light

2

Rear turn signal light

Turn and secure the bulb

base.

1

Stop/tail light

2

Rear turn signal light

7

Install the cover.

1

Align the cover claws with

the notches.

2

Press the cover until it is

fixed.

388

7-3. Do-it-yourself maintenance

 License plate light

1

Remove the cover.

Insert a properly sized screw-

driver into the hole of the cover,

and ply off the cover as shown

in the illustration.

To prevent damaging the vehi-

cle, wrap the screwdriver with a

tape.

2

Remove the light bulb.

3

Install the new bulb.

4

Install the cover.

Insert a properly sized screw-

driver into one of the holes,

push the screwdriver until click-

ing sound is heard. Repeat for

the other hole.

389

7-3. Do-it-yourself maintenance

5

Make sure that the cover is

secured by pressing on the

entire cover.

 Back-up light/rear fog light

1

Remove the clip and partly

remove the cover.

Pull the center section of the clip

and the remove and pull out the

lock.

2

Turn the bulb base counter-

clockwise.

7

3

Remove the light bulb.

390

7-3. Do-it-yourself maintenance

4

After installing the new bulb,

reinstall the clip.

When installing the clip, insert

the clip in and push the center of

the clip.

 Replacing the following bulbs

If any of the lights listed below has burnt out, have it replaced by

any authorized Toyota dealer or repairer, or another duly qualified

and equipped professional.

 Front position lights and daytime running lights (LED type)

 Stop/tail lights (LED type)

 High mounted stoplight

 LED Lights

The front position lights and daytime running lights (LED type), stop/tail lights

(LED type) and high mounted stoplight consists of a number of LEDs. If any

of the LEDs burn out, take your vehicle to any authorized Toyota dealer or

repairer, or another duly qualified and equipped professional to have the light

replaced.

If one or more LEDs in a stop light burn out, your vehicle may not conform to

local laws (ECE).

 Condensation build-up on the inside of the lens

Temporary condensation build-up on the inside of the headlight lens does not

indicate a malfunction. Contact any authorized Toyota dealer or repairer, or

another duly qualified and equipped professional for more information in the

following situations:

 Large drops of water have built up on the inside of the lens.

 Water has built up inside the headlight.

 When replacing light bulbs

P. 374

391

7-3. Do-it-yourself maintenance

WARNING

Replacing light bulbs

 Turn off the lights. Do not attempt to replace the bulb immediately after

turning off the lights.

The bulbs become very hot and may cause burns.

 Do not touch the glass portion of the light bulb with bare hands. When it is

unavoidable to hold the glass portion, use and hold with a clean dry cloth

to avoid getting moisture and oils on the bulb.

Also, if the bulb is scratched or dropped, it may blow out or crack.

 Fully install light bulbs and any parts used to secure them. Failure to do so

may result in heat damage, fire, or water entering the headlight unit. This

may damage the headlights or cause condensation to build up on the lens.

To prevent damage or fire

 Make sure bulbs are fully seated and locked.

 Check the wattage of the bulb before installing to prevent heat damage.

7

392

7-3. Do-it-yourself maintenance

Maintenanceandcare for Your Toyota Yaris 4 Door Third Generation (2011-2020)

Related Topics

Popular Owner Manuals

Latest Owner Manuals