Get Vehiclespecifications -> 9-1. Specifications Guide for Toyota Yaris 4 Door Third Generation (2011-2020)

468

9-1. Specifications

Maintenanc e data (fuel, oil level, etc .)

Dimensions and weights

Overall length

Overall width

3950 mm (155.5 in.)

1695 mm (66.7 in.)

1510 mm (59.4 in.)

1520 mm (59.8 in.)*²

1530 mm (60.2 in.)*³

Overall height*¹

Wheelbase

2510 mm (98.8 in.)

1485 mm (58.5 in.)*⁴

1470 mm (57.9 in.)*⁵

1460 mm (57.5 in.)*⁶

1470 mm (57.9 in.)*⁴

1460 mm (57.5 in.)*⁵

1445 mm (56.9 in.)*⁶

Front

Tread

Rear

1KR-FE engine

1450 kg (3197 lb.)

 Multidrive

1500 kg (3307 lb.)

Gross vehicle

mass

1NR-FE engine

1ND-TV engine

 Manual transmission

1490 kg (3285 lb.)

1545 kg (3406 lb.)

 1KR-FE engine

825 kg (1819 lb.)

 1NR-FE engine

Maximum

permissible

axle capacity

Front

Rear

850 kg (1874 lb.)

 1ND-TV engine

895 kg (1973 lb.)

825 kg (1819 lb.)

50 kg (110 lb.)

Drawbar load

469

9-1. Specifications

 1KR-FE engine

730 kg (1609 lb.)

 1NR-FE engine

with brake

880 kg (1940 lb.)

Towing capacity

 1ND-TV engine

780 kg (1719 lb.)

550 kg (1212 lb.)

without brake

Maximum permissible mass for tow-

ing hitch/bracket*⁷

19 kg (41 lb.)

*¹: Unladen vehicles

*²: Vehicles with rough road package (without raised vehicle height)

*³: Vehicles with rough road package (with raised vehicle height)

*⁴: 175/65R14, 175/70R14 or 175/65R15 tires

*⁵: 185/60R15 tires

*⁶: 195/50R16 tires

*⁷: Vehicle category N1 models

9

470

9-1. Specifications

Vehicle identification

 Vehicle identification number

The vehicle identification number (VIN) is the legal identifier for

your vehicle. This is the primary identification number for your Toy-

ota. It is used in registering the ownership of your vehicle.

This number is stamped under

the front right seat.

This number is also on the

manufacturer’s label on the left-

hand side of the center pillar.

471

9-1. Specifications

 Engine number

The engine number is stamped on the engine block as shown.

 1NR-FE engine

 1KR-FE engine

 1ND-TV engine

Engine

 Gasoline engine

 1KR-FE engine

Model

1KR-FE

Type

3-cylinder in line, 4-cycle, gasoline

71.0  84.0 mm (2.79  3.30 in.)

998 cm³(60.9 cu.in.)

Bore and stroke

Displacement

9

Valve clearance

(engine cold)

Intake: 0.145 — 0.235 mm (0.006 — 0.009 in.)

Exhaust: 0.275 — 0.365 mm (0.011 — 0.014 in.)

Drive belt tension

Automatic adjustment

472

9-1. Specifications

 1NR-FE engine

Model

1NR-FE

Type

4-cylinder in line, 4-cycle, gasoline

72.5  80.5 mm (2.85  3.17 in.)

1329 cm³(81.1 cu.in.)

Bore and stroke

Displacement

Valve clearance

(engine cold)

Automatic adjustment

Drive belt tension

 Diesel engine

 1ND-TV engine

Model

1ND-TV

Type

4-cylinder in line, 4-cycle, diesel

73.0  81.5 mm (2.87  3.21 in.)

1364 cm³(83.2 cu.in.)

Bore and stroke

Displacement

Valve clearance

(engine cold)

Intake: 0.11 — 0.17 mm (0.004 — 0.007 in.)

Exhaust: 0.14 — 0.20 mm (0.006 — 0.008 in.)

Drive belt tension

Automatic adjustment

NOTICE

Drive belt type (diesel engine)

The high strength drive belt is used for the generator side drive belt. When

replacing the drive belt, use Toyota genuine drive belt or equivalent high

strength drive belt. If the high strength drive belt is not used, durability of the

belt may become less than expected. The high strength drive belt is a belt

with Aramid core which has higher strength compared to usually available

belts with PET or PEN core.

473

9-1. Specifications

Fuel

 Gasoline engine

EU area:

Unleaded gasoline conforming to European

standard EN228 only

Except EU area:

Fuel type

Unleaded gasoline only

Research Octane

Number

95 or higher

Fuel tank capacity

(Reference)

42 L (11.1 gal., 9.2 Imp.gal.)

 Diesel engine

EU area:

Diesel fuel conforming to European standard

EN590

Except EU area:

Fuel type

Diesel fuel that contains 50 ppm or less of sulfur

Cetane number

48 or higher

Fuel tank capacity

(Reference)

42 L (11.1 gal., 9.2 Imp.gal.)

9

474

9-1. Specifications

Lubrication system (gasoline engine)

 Oil capacity (Drain and refill — reference*)

With filter

 1KR-FE engine

2.8 L (3.0 qt., 2.5 Imp.qt.)

 1NR-FE engine

3.4 L (3.6 qt., 3.0 Imp.qt.)

Without filter

 1KR-FE engine

2.6 L (2.7 qt., 2.3 Imp.qt.)

 1NR-FE engine

3.2 L (3.4 qt., 2.8 Imp.qt.)

*: The engine oil capacity is a reference quantity to be used when changing

the engine oil. Warm up and turn off the engine, wait more than 5 minutes,

and check the oil level on the dipstick.

475

9-1. Specifications

 Engine oil selection

“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Toyota

recommends the use of approved “Toyota Genuine Motor Oil”.

Another motor oil of matching quality can also be used.

Oil grade:

0W-20, 5W-20, 5W-30 and 10W-30:

API grade SL “Energy-Conserving”, SM “Energy-Conserving” or SN

“Resource-Conserving”; or ILSAC multigrade engine oil

15W-40 and 20W-50:

API grade SL, SM or SN multigrade engine oil

Recommended viscosity (SAE):

SAE 0W-20 is filled into your

Preferred

Toyota vehicle at manufactur-

ing, and the best choice for

good fuel economy and good

starting in cold weather.

If SAE 0W-20 oil is not avail-

able, SAE 5W-30 oil may be

used. However, it should be

replaced with SAE 0W-20 at the

next oil change.

Temperature range anticipated

before next oil change

If you use SAE 10W-30 or a

higher viscosity engine oil in

extremely low temperatures,

the engine may become difficult

to start, so SAE 0W-20, 5W-20

or 5W-30 engine oil is recom-

mended.

9

476

9-1. Specifications

Oil viscosity (0W-20 is explained here as an example):

• The 0W in 0W-20 indicates the characteristic of the oil which

allows cold startability. Oils with a lower value before the W allow

for easier starting of the engine in cold weather.

• The 20 in 0W-20 indicates the viscosity characteristic of the oil

when the oil is at high temperature. An oil with a higher viscosity

(one with a higher value) may be better suited if the vehicle is

operated at high speeds, or under extreme load conditions.

How to read oil container labels:

Either or both API registered marks are added to some oil contain-

ers to help you select the oil you should use.

1

API Service Symbol

Top portion: “API SERVICE SN”

means the oil quality designa-

tion by American Petroleum

Institute (API).

Center portion: “SAE 0W-20”

means the SAE viscosity grade.

Lower portion: “Resource-Con-

serving” means that the oil has

fuel-saving and environmental

protection capabilities.

2

ILSAC Certification Mark

The International Lubricant Specification Advisory Committee (ILSAC)

Certification Mark is displayed on the front of the container.

Lubrication system (diesel engine)

 Oil capacity (Drain and refill — reference*)

With filter

3.9 L (4.1 qt., 3.4 Imp.qt.)

3.5 L (3.7 qt., 3.1 Imp.qt.)

Without filter

*: The engine oil capacity is a reference quantity to be used when changing

the engine oil. Warm up and turn off the engine, wait more than 5 minutes,

and check the oil level on the dipstick.

477

9-1. Specifications

 Engine oil selection

 Vehicles without a DPF system*

“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Toyota

recommends the use of approved “Toyota Genuine Motor Oil”.

Another motor oil of matching quality can also be used.

Oil grade: ACEA C2, B1, API CF-4 or CF

Recommended viscosity (SAE):

SAE 0W-30 is filled into your

Preferred

Toyota vehicle at manufactur-

ing, and the best choice for

good fuel economy and good

starting in cold weather.

If you use SAE 10W-30 or a

higher viscosity engine oil in

extremely low temperatures,

the engine may become difficult

to start, so SAE 5W-30 or

0W-30 engine oil is recom-

mended.

Temperature range anticipated

before next oil change

Oil viscosity (0W-30 is explained here as an example):

• The 0W in 0W-30 indicates the characteristic of the oil which

allows cold startability. Oils with a lower value before the W allow

for easier starting of the engine in cold weather.

• The 30 in 0W-30 indicates the viscosity characteristic of the oil

when the oil is at high temperature. An oil with a higher viscosity

(one with a higher value) may be better suited if the vehicle is

operated at high speeds, or under extreme load conditions.

*: To determine whether or not your vehicle has a DPF system, contact any

authorized Toyota dealer or repairer, or another duly qualified and

equipped professional.

9

478

9-1. Specifications

 Vehicles with a DPF system*

“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Toyota

recommends the use of approved “Toyota Genuine Motor Oil”.

Another motor oil of matching quality can also be used.

Oil grade: ACEA C2

NOTICE

Using engine oil other than ACEA C2 may damage the catalytic converter.

Recommended viscosity (SAE):

SAE 0W-30 is filled into your

Toyota vehicle at manufactur-

ing, and the best choice for

good fuel economy and good

starting in cold weather.

Preferred

Temperature range anticipated

before next oil change

Oil viscosity (0W-30 is explained here as an example):

• The 0W in 0W-30 indicates the characteristic of the oil which

allows cold startability. Oils with a lower value before the W allow

for easier starting of the engine in cold weather.

• The 30 in 0W-30 indicates the viscosity characteristic of the oil

when the oil is at high temperature. An oil with a higher viscosity

(one with a higher value) may be better suited if the vehicle is

operated at high speeds, or under extreme load conditions.

*: To determine whether or not your vehicle has a DPF system, contact any

authorized Toyota dealer or repairer, or another duly qualified and

equipped professional.

479

9-1. Specifications

Cooling system

 Gasoline engine

1KR-FE

engine

4.5 L (4.8 qt., 4.0 Imp.qt.)

 Multidrive

Capacity

(Reference)

4.8 L (5.1 qt., 4.2 Imp.qt.)

1NR-FE

engine

 Manual transmission

4.6 L (4.9 qt., 4.0 Imp.qt.)

Use either of the following:

• “Toyota Super Long Life Coolant”

• A similar high-quality ethylene glycol-based

non-silicate, non-amine, non-nitrite, and

non-borate coolant with long-life hybrid

organic acid technology

Coolant type

Do not use plain water alone.

 Diesel engine

 Without a power heater

4.5 L (4.8 qt., 4.0 Imp.qt.)

Capacity

(Reference)

 With a power heater

4.9 L (5.2 qt., 4.3 Imp.qt.)

Use either of the following:

• “Toyota Super Long Life Coolant”

• A similar high-quality ethylene glycol-based

non-silicate, non-amine, non-nitrite, and

non-borate coolant with long-life hybrid

organic acid technology

Coolant type

Do not use plain water alone.

9

480

9-1. Specifications

Ignition system (gasoline engine only)

Spark plug

Make

 1KR-FE engine

DENSO SC16HR11

 1NR-FE engine

DENSO SC20HR11

1.1 mm (0.043 in.)

Gap

NOTICE

Iridium-tipped spark plugs

Use only iridium-tipped spark plugs. Do not adjust the spark plug gap.

Electrical system

Battery

Open voltage* at

20C (68F):

12.6 — 12.8 V Fully charged

12.2 — 12.4 V Half charged

11.8 — 12.0 V Discharged

(*: Voltage is checked 20 minutes after the

engine and all lights are turned off.)

Charging rates

5 A max.

Multidrive

Fluid capacity*

Fluid type

6.4 L (6.8 qt., 5.6 Imp.qt.)

Toyota Genuine CVT Fluid FE

*: The fluid capacity is the reference quantity. If replacement is necessary,

contact any authorized Toyota dealer or repairer, or another duly qualified

and equipped professional.

481

9-1. Specifications

NOTICE

Multidrive fluid type

Using Multidrive fluid other than “Toyota Genuine CVT Fluid FE” may cause

deterioration in shift quality, locking up of your transmission accompanied

by vibration, and ultimately damage the transmission of your vehicle.

Manual transmission

 1KR-FE engine

1.7 L (1.8 qt., 1.5 Imp.qt.)

Gear oil capacity

(Reference)

 1NR-FE and 1ND-TV engines

2.4 L (2.5 qt., 2.1 Imp.qt.)

Use either of the following:

• “TOYOTA Genuine Manual Transmission Gear

Oil LV”

• Other gear oil that meets API GL-4 and

SAE 75W specifications

Gear oil type

NOTICE

Manual transmission gear oil

Please be aware that depending on the particular characteristics of the gear

oil used or the operating conditions, idle sound, shift feeling and/or fuel effi-

ciency may be different or affected. Toyota recommends to use “TOYOTA

Genuine Manual Transmission Gear Oil LV” to achieve optimal perfor-

mance.

Clutch

Pedal free play

Fluid type

5 — 15 mm (0.2 — 0.6 in.)

SAE J1704 or FMVSS No. 116 DOT 4

9

482

9-1. Specifications

Brakes

 Rear drum brake

83 mm (3.27 in.) Min.

Gasoline

engines

 Rear disk brake

Left-

hand

79 mm (3.11 in.) Min.

drive

vehicles

 Rear drum brake

81 mm (3.19 in.) Min.

Diesel

engines

 Rear disk brake

78 mm (3.07 in.) Min.

Pedal

clearance*¹

 Rear drum brake

76 mm (2.99 in.) Min.

Gasoline

engines

 Rear disk brake

Right-

hand

drive

74 mm (2.91 in.) Min.

 Rear drum brake

vehicles

75 mm (2.95 in.) Min.

Diesel

engines

 Rear disk brake

73 mm (2.87 in.) Min.

1 — 6 mm (0.04 — 0.24 in.)

 Rear drum brake

Pedal free play

5 — 7 clicks

Parking brake lever travel*²

 Rear disc brake

4 — 6 clicks

Fluid type

SAE J1704 or FMVSS No.116 DOT 4

*¹: Minimum pedal clearance when depressed with a force of 300 N (31.0 kgf,

67.4 lbf) while the engine is running

*²: Parking brake lever travel when pulled up with a force of 200 N (20.4 kgf,

45.0 lbf)

Steering

Free play

Less than 30 mm (1.2 in.)

483

9-1. Specifications

Tires and wheels

 14-inch tires (Type A)

Tire size

175/65R14 82T

Tire inflation pressure

(Recommended

tire inflation pressure)

cold 220 kPa (2.2 kgf/cm²or bar, 32 psi)

Wheel size

14  5J

Wheel nut torque

103 N·m (10.5 kgf·m, 76 ft·lbf)

 14-inch tires (Type B)

Tire size

175/70R14 84S

Front wheel

Rear wheel

Tire inflation pressure

kPa (kgf/cm²or bar, psi) kPa (kgf/cm²or bar, psi)

(Recommended

tire inflation pressure)

cold

250 (2.5, 36)

240 (2.4, 35)

Wheel size

14  5J

Wheel nut torque

103 N·m (10.5 kgf·m, 76 ft·lbf)

 15-inch tires (Type A)

Tire size

175/65R15 84H

Front wheel

Rear wheel

kPa (kgf/cm²or bar, psi) kPa (kgf/cm²or bar, psi)

Tire inflation pressure

Standard tire pressure: Standard tire pressure:

220 (2.2, 32)

(Recommended

tire inflation pressure)

cold

230 (2.3, 33)

ECO tire pressure*:

250 (2.5, 36)

ECO tire pressure*:

240 (2.4, 35)

Wheel size

15  5J

9

Wheel nut torque

103 N·m (10.5 kgf·m, 76 ft·lbf)

*: For some models, ECO tire pressure is shown on the tire pressure label.

(P. 440)

“For optimizing fuel economy, ECO tire pressure is recommended.

Tire pressure affects traveling comfort, road noise and steering character-

istics.”

484

9-1. Specifications

 15-inch tires (Type B)

Tire size

185/60R15 84H

Front wheel

Rear wheel

Vehicle speed kPa (kgf/cm²kPa (kgf/cm²or

or bar, psi)

bar, psi)

Tire inflation pressure

(Recommended

tire inflation pressure)

160 km/h

cold (99 mph) or

220 (2.2, 32)

less

More than

160 km/h

(99 mph)

240 (2.4, 35)

220 (2.2, 32)

Wheel size

15  5 1/2J

Wheel nut torque

103 N·m (10.5 kgf·m, 76 ft·lbf)

 16-inch tires

Tire size

195/50R16 84V

Front wheel

Rear wheel

Vehicle speed kPa (kgf/cm²kPa (kgf/cm²or

or bar, psi)

bar, psi)

Tire inflation pressure

(Recommended

tire inflation pressure)

160 km/h

cold (99 mph) or

220 (2.2, 32)

200 (2.0, 29)

less

More than

160 km/h

(99 mph)

240 (2.4, 35)

210 (2.1, 30)

Wheel size

16  6J

Wheel nut torque

103 N·m (10.5 kgf·m, 76 ft·lbf)

485

9-1. Specifications

 Compact spare tires

Tire size

T125/70D15 95M

Tire inflation pressure

(Recommended

tire inflation pressure)

cold 420 kPa (4.2 kgf/cm²or bar, 60 psi)

Wheel size

15  4T

Wheel nut torque

103 N·m (10.5 kgf·m, 76 ft·lbf)

Tire size

T125/70D16 96M

Tire inflation pressure

(Recommended

tire inflation pressure)

cold 420 kPa (4.2 kgf/cm²or bar, 60 psi)

Wheel size

16  4T

Wheel nut torque

103 N·m (10.5 kgf·m, 76 ft·lbf)

 When towing a trailer

Add 20.0 kPa (0.2 kgf/cm²or bar, 3 psi) to the recommended tire inflation

pressure, and drive at speeds below 100 km/h (62 mph).

9

486

9-1. Specifications

Light bulbs

Light Bulbs

Halogen headlights

W

Type

Reflector type

Projector type

60/55

55

A

B

Front fog lights*

19

C

D

Front position light/daytime running lights

(bulb type)

21/5

Front turn signal lights

Side turn signal lights

Rear turn signal lights

Stop/tail lights (bulb type)

Back-up light

21

5

E

G

D

F

Exterior

21

21/5

21

5

Rear fog light

License plate lights

Vanity lights*

5

Interior

Personal lights/interior light

Luggage compartment light

5

D

F

5

A: H4 halogen bulbs

C: H16 halogen bulbs

E: Wedge base bulbs (amber)

G: Single end bulbs (clear)

*: If equipped

B: HIR2 halogen bulbs

D: Wedge base bulbs (clear)

F: Double end bulbs

487

9-1. Specifications

Fuel inform at ion

 Gasoline engine

EU area:

Your vehicle must use only unleaded gasoline conforming to Euro-

pean standard EN228.

For optimum engine performance, select unleaded gasoline with a

Research Octane Number of 95 or higher.

Except EU area:

Your vehicle must use only unleaded gasoline.

For optimum engine performance, select unleaded gasoline with a

Research Octane Number of 95 or higher.

 Diesel engine

EU area:

Your vehicle must use only diesel fuel conforming to European stan-

dard EN590.

Except EU area:

Your vehicle must use only diesel fuel that contains 50 ppm or less

of sulfur and has a cetane number of 48 or higher.

 Fuel tank opening for unleaded gasoline (gasoline engine)

To help prevent incorrect fueling, your vehicle has a fuel tank opening that

only accommodates the special nozzle on unleaded fuel pumps.

 If you plan to drive in foreign countries (diesel engine)

Low sulfur diesel fuel may not be available, so please check the availability

with your distributor.

 If your engine knocks

 Consult any authorized Toyota dealer or repairer, or another duly qualified

and equipped professional.

9

 You may occasionally notice light knocking for a short time while accelerat-

ing or driving uphill. This is normal and there is no need for concern.

488

9-1. Specifications

NOTICE

Notice on fuel quality (gasoline engine)

 Do not use improper fuels. If improper fuels are used, the engine will be

damaged.

 Do not use leaded gasoline.

Leaded gasoline will cause the three-way catalytic converter to lose its

effectiveness and the emission control system to function improperly.

 EU area: Bioethanol fuel sold under names such as “E50” or “E85” and

fuel containing a large amount of ethanol should not be used. The use of

these fuels will damage the vehicle’s fuel system. In case of any doubt,

ask any authorized Toyota dealer or repairer, or another duly qualified and

equipped professional.

 Except EU area: Bioethanol fuel sold under names such as “E50” or “E85”

and fuel containing a large amount of ethanol should not be used. Your

vehicle can use gasoline mixed with 10% max ethanol. The use of fuel

with more than 10% ethanol content (E10) will damage the vehicle’s fuel

system. You must ensure that refueling is carried out only from a source

where fuel specification and quality can be guaranteed. In case of any

doubt, ask any authorized Toyota dealer or repairer, or another duly quali-

fied and equipped professional.

Notice on fuel quality (diesel engine)

 Do not use improper fuels. If improper fuels are used, the engine will be

damaged.

 Do not use a fuel that contains more than 50 ppm of sulfur.

Use of such a high sulfur fuel may damage the engine.

 EU area: FAME (Fatty Acid Methyl Ester) fuel sold under names such as

“B30” or “B100” and fuel containing a large amount of FAME should not be

used. The use of these fuels will damage the vehicle’s fuel system. In case

of any doubt, ask any authorized Toyota dealer or repairer, or another duly

qualified and equipped professional.

 Except EU area: FAME (Fatty Acid Methyl Ester) fuel sold under names

such as “B30” or “B100” and fuel containing a large amount of FAME

should not be used. Your vehicle can use diesel mixed with 5% max bio-

diesel FAME (B5). The use of fuel with more than 5% FAME content (B5)

will damage the vehicle’s fuel system. You must ensure that refueling is

carried out only from a source where fuel specification and quality can be

guaranteed. In case of any doubt, ask any authorized Toyota dealer or

repairer, or another duly qualified and equipped professional.

Vehiclespecifications -> 9-1. Specifications for Your Toyota Yaris 4 Door Third Generation (2011-2020)

Related Topics

Vehiclespecifications

Popular Owner Manuals

Latest Owner Manuals