Get Vehicle care -> Bulb replacement Guide for Vauxhall Combo Van Fifth Generation (2018-2026)

220

Vehicle care

1. Remove the protective cover by

pulling.

Bulb replacement

Before replacing a bulb, ensure that

all exterior and interior lights and the

ignition are switched off.

Only hold a new bulb at the base. Do

not touch the bulb glass with bare

hands.

Use only the same bulb type for

replacement.

Replace headlight bulbs from within

the engine compartment.

Low beam (1) outer bulb

High beam (2) inner bulb

Bulb check

2. Withdraw the bulb socket from the

reflector housing.

Low beam (1)

After a bulb replacement switch on

the ignition, operate and check the

lights.

Halogen headlights

Halogen headlights with separate

bulbs for low beam and high beam.

Vehicle care

221

3. Detach the bulb from the bulb

socket and replace the bulb.

4. Insert the bulb socket into the

reflector housing.

5. Fit the protective cover on.

High beam (2)

3. Detach the bulb from the bulb

socket and replace the bulb.

2. Disengage the spring clip from the

retainer by moving it to the

righthand side. Swivel the spring

clip downwards.

4. Insert the bulb socket into the

reflector housing.

Withdraw the bulb socket from the

reflector housing.

5. Fit the protective cover on.

1. Remove the protective cover by

pulling.

222

Vehicle care

Have lights repaired by a workshop in

case of failure.

Sidelight / daytime running light

with bulbs

Front fog lights

2. Remove the bulb from the bulb

socket by pulling.

3. Replace and insert the new bulb

1. Rotate the bulb socket

into the bulb socket.

anticlockwise to disengage and

withdraw from the reflector.

4. Insert the bulb socket into the light

assembly and turn clockwise.

1. Wrap a cloth around the tip of a flat

screwdriver to prevent paint

damage. Insert the screwdriver in

the recess at the edge of the

cover. Release the cover by

levering it out carefully.

Sidelight / daytime running light

with LEDs

In case of defective LEDs, have them

replaced by a workshop.

LED headlights

Daytime running lights are designed

as LEDs and can not be changed.

Vehicle care

223

3. Turn the bulb socket

anticlockwise and remove it from

the light assembly.

Front turn lights

2. Unscrew and remove the two

screws and remove the light

assembly to the front.

1. Rotate the bulb socket

anticlockwise to disengage and

withdraw from the reflector.

4. Disengage the plug connector by

pulling the retaining lug.

5. Remove and replace the bulb unit

and attach the plug connector.

Note that the bulb and the socket

are one unit and have to be

changed together.

6. Insert the bulb socket into the light

assembly by turning clockwise

and engage.

7. Mount the light assembly by

tightening the two screws.

8. Attach and engage the cover.

224

Vehicle care

2. Slightly press down the bulb, turn

it anticlockwise and remove it

from the socket.

3. Replace and insert the new bulb

into socket by turning clockwise.

4. Insert the bulb socket into the

reflector and turn clockwise.

Tail lights

Light assembly in the body

2. Carefully withdraw the tail light

assembly from recess and

4. Press the retaining lug

backwards, pull the bulb carrier

and disengage the remaining

retaining lugs.

Vehicle with tailgate

remove. Take care that the cable

duct remains in position.

3. Detach the cable from the

retainer.

1. Unscrew and remove the two

screws.

Vehicle care

225

5. Push the bulb slightly down, turn

it and remove it from the bulb

carrier. Replace the bulb:

1. Unscrew and remove the two

screws.

Rear fog light (1)

Reversing light (2)

Turn light / hazard warning flasher

(3)

Tail light / brake light (4)

6. Attach the bulb carrier to the light

assembly.

7. Attach the cable to the retainer.

4. Disengage the retaining lugs to

remove the bulb carrier.

8. Attach the light assembly to the

vehicle body and tighten both

screws.

2. Carefully withdraw the tail light

assembly from recess and

remove. Take care that the cable

Vehicle with rear doors

duct remains in position.

3. Detach the cable from the

retainer.

5. Push the bulb slightly down, turn

it and remove it from the bulb

carrier. Replace the bulb:

226

Vehicle care

Tail light / brake light (1)

Turn light / hazard warning flasher

(2) outer bulb

Reversing light (3) inner bulb

Rear fog light (4)

Side turn lights

To replace the bulb, remove the lamp

housing:

6. Attach the bulb carrier to the light

assembly.

7. Attach the cable to the retainer.

8. Attach the light assembly to the

vehicle body and tighten both

screws.

2. Press the retaining lug upwards

and remove the bulb socket from

the plug connector.

3rd-brake light

The 3rd-brake light is designed as

LED and can not be changed.

Have lights repaired by a workshop in

case of failure.

3. Replace the complete unit.

1. Slide the lamp housing forward

and remove it at the back.

4. Insert left end of the lamp, slide to

the left and insert right end.

Bulb check

Switch on the ignition, operate and

check all lights.

Vehicle care

227

2. Pull the bulb from the bulb holder

and replace it.

Number plate light

Electrical system

3. Attach the cover.

Fuses

Data on the replacement fuse must

match the data on the defective fuse.

There are two fuse boxes in the

vehicle:

Interior lights

Have the following bulbs replaced by

a workshop:

●

courtesy light, reading lights

load compartment light

instrument panel illumination

●

engine compartment

instrument panel

Before replacing a fuse, turn off the

respective switch and the ignition.

A blown fuse can be recognised by its

melted wire.

1. Insert a screwdriver in the recess

of the cover and remove it.

Caution

Do not replace the fuse until the

cause of the fault has been

remedied.

Some functions are protected by

several fuses.

Fuses may also be inserted without

existence of a function.

Vehicle care -> Bulb replacement for Your Vauxhall Combo Van Fifth Generation (2018-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals