Get Vehicle care -> Bulb replacement Guide for Vauxhall Corsa 4 Door First Generation (2014-2019)

196

Vehicle care

Wiper blade on the rear window

Bulb replacement

Switch off the ignition and switch off

the relevant switch or close the doors.

Only hold a new bulb at the base! Do

not touch the bulb glass with bare

hands.

Use only the same bulb type for

replacement.

Replace headlight bulbs from within

the engine compartment.

Sidelight/daytime running light (1)

Low beam (2)

High beam (3)

Bulb check

After a bulb replacement switch on

the ignition, operate and check the

lights.

Lift wiper arm. Disengage wiper blade

as shown in illustration and remove.

Front turn signal lights 3 200.

Attach the wiper blade slightly angled

to the wiper arm and push until it

engages.

Halogen headlights

Lower wiper arm carefully.

Halogen headlights with separate

bulbs for sidelight, low beam and high

beam.

Vehicle care

197

2. Press the clip to disengage bulb

holder. Withdraw the bulb holder

from the reflector.

Low beam

High beam

1. Rotate the cap (2) anticlockwise

and remove it.

1. Rotate the cap (3) anticlockwise

and remove it.

3. Detach the bulb from the bulb

holder and replace the bulb.

4. Insert the bulb holder with the clip

downwards and engage into the

reflector until it clicks.

5. Install cap.

198

Vehicle care

2. Press the clip to disengage bulb

holder. Withdraw the bulb holder

from the reflector.

2. Press both clips together and

withdraw the bulb socket from the

headlamp housing.

Sidelight/daytime running light

with bulbs

1. Rotate bulb socket (1)

3. Detach the bulb from the bulb

holder and replace the bulb.

3. Remove the bulb from the socket

by pulling.

anticlockwise to disengage.

4. Insert the bulb holder with the clip

downwards and engage into the

reflector until it clicks.

4. Replace and insert new bulb into

socket.

5. Insert the bulb socket into the

headlamp housing and turn

clockwise.

5. Install cap.

Vehicle care

199

2. Rotate the bulb holder

Sidelight/daytime running light

with LEDs

Sidelights and daytime running lights

are designed as LEDs and cannot be

changed. Consult a workshop in case

of a defective LED.

Corner lighting

anticlockwise to disengage.

Withdraw the bulb holder from the

reflector.

Xenon headlights

9 Danger

Xenon headlights work under

extremely high electrical voltage.

Do not touch. Have bulbs replaced

by a workshop.

1. Rotate the cap (3) anticlockwise

and remove it.

3. Remove the bulb from the plug

connector by disengaging and

pulling.

4. Replace the bulb. Connect and

engage bulb holder with the plug

connector.

5. Insert the bulb holder into the

reflector and rotate clockwise to

secure.

Sidelight/daytime running lights are

designed as LEDs and cannot be

changed.

Bulbs for corner lighting can be

changed.

Front turn signal lights 3 200.

6. Fit the cap and rotate clockwise.

200

Vehicle care

Fog lights

Tail lights

The bulbs are accessible from the

underside of the vehicle.

2. Disengage the bulb socket from

the plug connector by pressing

the retaining lug.

3. Remove and replace the bulb

socket with bulb and attach the

plug connector.

1. Release the cover in the load

compartment on the respective

side and remove.

1. Turn the bulb holder anti-

clockwise and remove it from the

reflector.

4. Insert the bulb socket into the

reflector by turning clockwise and

engage.

Front turn signal lights

Front turn signal lights consist of long-

life bulbs which cannot be changed.

Consult a workshop in case of a

defective long-life bulb.

Vehicle care

201

2. Unscrew both plastic securing

nuts from the inside by hand.

4. Press the retaining lugs and

remove the bulb carrier from the

light assembly.

Reversing light/rear fog light

Reversing light is located on the left

light assembly in the tailgate, and the

rear fog light is located on the right

light assembly in the tailgate.

The description of bulb replacement

is the same for both lights.

3. Carefully withdraw the light

assembly from the recesses and

remove.

5. Remove and replace the bulb by

pushing the bulb slightly into the

socket and rotating anticlockwise:

Tail light/Brake light (1)

Turn signal light (2)

1. Remove screw from the tailgate.

6. Insert and turn bulb clockwise into

the tail light assembly. Fit light

assembly with the retaining pins

into the recesses of the vehicle

body and tighten the plastic

securing nuts from inside the load

compartment.

Close cover and engage.

202

Vehicle care

Side turn signal lights

To replace bulb, remove lamp

housing:

2. Move light assembly slightly to the

outside, then withdraw from the

tailgate.

4. Remove the bulb by pushing

slightly into the socket and

rotating anticlockwise. Replace

the bulb.

1. Slide lamp to its left side and

remove with its right end.

5. Insert the bulb socket into the

assembly and turn to secure.

6. Attach light assembly into the

tailgate and secure with the

screw.

3. Remove the bulb holder by

turning.

Vehicle care

203

4. Insert bulb holder and turn

clockwise.

5. Insert left end of the lamp, slide to

the left and insert right end.

Centre high-mounted brake

light

Have LEDs replaced by a workshop.

Number plate light

2. Turn bulb holder anticlockwise

and remove from housing.

2. Remove lamp downwards, taking

care not to pull on the cable.

1. Insert screwdriver in recess of the

cover, press to the side and

release spring.

3. Pull bulb from bulb holder and

replace it.

3. Remove bulb holder from lamp

housing by turning anticlockwise.

204

Vehicle care

4. Pull bulb from bulb holder and

replace it.

There are different kinds of fuses in

the vehicle.

Electrical system

5. Insert bulb holder into lamp

Fuses

housing and turn clockwise.

Data on the replacement fuse must

match the data on the defective fuse.

6. Insert lamp into bumper and let

engage.

There are two fuse boxes in the

vehicle:

Interior lights

Courtesy light, reading lights

●

in the front left of the engine

compartment

in left-hand drive vehicles, behind

the light switch, or, in right-hand

drive vehicles, behind the

glovebox

Have bulbs replaced by a workshop.

Load compartment light

Have bulbs replaced by a workshop.

Before replacing a fuse, turn off the

respective switch and the ignition.

Depending on the type of fuse, a

blown fuse can be recognized by its

melted wire. Do not replace the fuse

until the cause of the fault has been

remedied.

Dome light

Have bulbs replaced by a workshop.

Some functions are protected by

Instrument panel

illumination

several fuses.

Fuses may also be inserted without

existence of a function.

Have bulbs replaced by a workshop.

Fuse extractor

A fuse extractor may be located in the

fuse box in the engine compartment.

Vehicle care -> Bulb replacement for Your Vauxhall Corsa 4 Door First Generation (2014-2019)

Related Topics

Vehicle care

Popular Owner Manuals

Latest Owner Manuals