Get Vehicle care -> Bulb replacement Guide for Vauxhall Crossland SUV First Generation (2020-2024)

180

Vehicle care

When the vehicle battery is being

replaced, ensure that there are no

open ventilation holes in the vicinity of

the positive terminal. If a ventilation

hole is open in this area, it must be

closed off with a dummy cap, and the

ventilation in the vicinity of the

Discharge protection

Warning label

Battery voltage

When the vehicle battery voltage is

running low, a warning message will

appear in the Driver Information

Centre.

negative terminal must be opened.

When the vehicle is being driven, the

load reduction function temporarily

deactivates certain functions, e.g. the

heated rear window.

Ensure that the vehicle battery is

always replaced by the same type of

battery.

The vehicle battery has to be

The deactivated functions are

reactivated automatically as soon as

conditions permit.

replaced by a workshop.

Stop-start system 3 126.

Meaning of symbols:

Idle boost

●

No sparks, naked flames or

smoking.

Charging the vehicle battery

If charging of the vehicle battery is

required due to battery condition, the

power output of the generator must

be increased. This will be achieved by

an idle boost which may be audible.

●

Always shield eyes. Explosive

gases can cause blindness or

injury.

9 Warning

On vehicles with stop-start

system, ensure that the charging

potential does not exceed 14.6 V

when using a battery charger.

Otherwise the vehicle battery may

be damaged.

●

Keep the vehicle battery out of

A message appears in the Driver

Information Centre.

reach of children.

The vehicle battery contains

sulphuric acid which could cause

blindness or serious burn

injuries.

Power outlet

The power outlets are deactivated in

the event of low vehicle battery

voltage.

Jump starting 3 208.

Vehicle care

181

●

See the Owner's Manual for

further information.

Explosive gas may be present in

the vicinity of the vehicle battery.

Within one minute after switching off

ignition, operate the wiper lever to

positon the wiper blades vertically on

the windscreen.

Lift the wiper arm until it stays in the

raised position, press button to

disengage the wiper blade and

remove.

Diesel fuel system bleeding

If the tank has been run dry, the diesel

fuel system must be bled. Switch on

the ignition three times for

15 seconds at a time. Then crank the

engine for a maximum of

40 seconds. Repeat this process after

no less than 5 seconds. If the engine

fails to start, seek the assistance of a

workshop.

Power saving mode

This mode deactivates electrical

consumers to avoid excessive

discharging of the vehicle battery.

These consumers, such as the

infotainment system, windscreen

wipers, low beam headlights,

courtesy light, etc. can be used for a

total maximum time of about

40 minutes after ignition is switched

off.

Attach the wiper blade slightly angled

to the wiper arm and push until it

engages.

Lower wiper arm carefully.

Wiper blade replacement

Windscreen

Rear window

Deactivating power saving mode

Power saving mode is deactivated

automatically when the engine is

restarted. Run the engine for a

sufficient charge:

●

for less than 10 minutes to use

the consumers for approx.

5 minutes

●

for more than 10 minutes to use

the consumers for up to approx.

30 minutes

Lift wiper arm. Disengage wiper blade

as shown in illustration and remove.

Switch off ignition.

182

Vehicle care

Attach the wiper blade slightly angled

to the wiper arm and push until it

engages.

Halogen headlights

Bulb replacement

Switch off the ignition and switch off

the relevant switch or close the doors.

Lower wiper arm carefully.

Only hold a new bulb at the base. Do

not touch the bulb glass with bare

hands.

Use only the same bulb type for

replacement.

Replace headlight bulbs from within

the engine compartment.

Bulb check

After a bulb replacement switch on

the ignition, operate and check the

lights.

1 : high beam, turn light

2 : low beam

Vehicle care

183

2. Withdraw the upper bulb socket

from the reflector housing.

High beam

Turn light

1. Rotate the cap anticlockwise and

remove it.

1. Rotate the cap anticlockwise and

remove it.

3. Remove the bulb from the plug

connector by pulling.

4. Replace the bulb and connect it to

the plug connector.

5. Insert and push the bulb socket

into the reflector housing by

setting the lug into position.

6. Fit the cap and rotate clockwise.

184

Vehicle care

2. Rotate the lower bulb socket

anticlockwise to disengage.

Withdraw the bulb socket from the

reflector housing.

2. Lift the retainer, then pull the plug

connector backwards.

3. Fold down the retainer and

remove the bulb from the reflector

housing.

Low beam

1. Rotate the cap anticlockwise and

remove it.

3. Press latch and remove the bulb

from the bulb socket.

4. Replace the bulb and push it into

the reflector housing by setting

the lug into position.

4. Replace the bulb and attach it to

the bulb socket.

5. Insert the bulb socket into the

reflector housing and rotate

clockwise.

5. Fold up the retainer and hold in

position.

6. Attach the plug connector to the

bulb and fix it with the retainer.

6. Fit the cap and rotate clockwise.

7. Fit the cap and rotate clockwise.

Vehicle care

185

1. Rotate the cap anticlockwise and

remove it.

3. Remove the bulb from the plug

connector by pulling.

Sidelight / daytime running light

In case of defective LEDs, have them

replaced by a workshop.

4. Replace the bulb and connect it to

the plug connector.

5. Insert the bulb socket into the

reflector housing and push it

forwards until it engages.

LED headlights

Headlights for low and high beam,

sidelights, daytime running lights and

turn lights are designed as LEDs and

cannot be changed.

6. Fit the cap and rotate clockwise.

Front fog lights

Have lights repaired by a workshop in

case of failure.

The bulbs are accessible from the

underside of the vehicle.

Eco-LED headlights

2. Push the bulb socket to the left

and withdraw it from the reflector

housing.

The turn lights are designed as bulbs.

1. Turn the bulb holder anti-

clockwise and remove it from the

reflector housing.

186

Vehicle care

2. Remove the light assembly by

pulling it straight back.

3. Remove the bulb socket.

a) Version without LED:

Light assembly in the body

Detaching the light assembly

2. Disengage the bulb socket from

the plug connector by pressing

the retaining lug.

3. Remove and replace the bulb

socket with bulb and attach the

plug connector.

1. Unscrew the two screws that

secure the light assembly.

Remove the three screws and

take out.

b) Version with LED:

4. Insert the bulb socket into the

reflector housing by turning

clockwise and engage.

Tail lights

Depending on version, tail lights and

brake lights are designed as LEDs. In

case of defective LEDs, have them

replaced by a workshop.

Vehicle care

187

1 : tail light / brake light

2 : turn light

b) Version with LED:

Remove from the light assembly

by turning it anticlockwise.

4. Remove the bulb.

2. Attach the light assembly to the

vehicle body and secure with the

two screws.

a) Version without LED:

Pull straight out to remove from

the socket and replace.

Attaching the light assembly

1. Depending on version, attach the

bulb carrier to the light assembly

and secure with the three screws

or attach turn light bulb socket.

Pull and replace.

188

Vehicle care

2. Unscrew the plastic nut by hand.

Light assembly in the tailgate

Detaching the light assembly

Press latch to release and remove

bulb socket.

b) Version with LED:

3. Carefully withdraw the light

assembly from the recesses and

remove.

1. Release the cover in the tailgate

and remove it.

4. Remove bulb socket.

a) Version without LED:

Vehicle care

189

Remove the reverse light bulb

socket from the light assembly by

turning it anticlockwise.

5. Remove bulb.

a) Version without LED:

Pull straight out to remove and

replace.

2. Attach the light assembly to the

tailgate.

3. Secure the light assembly with the

Attaching the light assembly

1. Depending on version, attach the

bulb carrier to the light assembly

or attach the reverse light bulb

socket.

plastic nut.

4. Attach the cover to the tailgate.

Remove and replace.

1 : tail light

2 : rear fog light or reverse light

b) Version with LED:

190

Vehicle care

4. Insert bulb socket and turn

clockwise.

5. Insert left end of the light

assembly, slide to the left and

insert right end.

Side turn lights

To replace bulb, remove light

assembly:

Number plate light

The number plate light is designed as

LEDs and cannot be changed. In

case of defective LEDs, have them

replaced by a workshop.

2. Turn bulb socket anticlockwise

and remove from light assembly.

Interior lights

Have the following bulbs replaced by

a workshop:

1. Slide the light assembly forward

and remove it at the back.

●

courtesy light, reading lights

load compartment light

instrument panel illumination

3. Pull bulb from bulb socket and

replace it.

Vehicle care -> Bulb replacement for Your Vauxhall Crossland SUV First Generation (2020-2024)

Related Topics

Vehicle care

Popular Owner Manuals

Latest Owner Manuals