2019-2026 Volvo V90 SUV MAINTENANCE AND SERVICE -> Replacing bulbs User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

MAINTENANCE AND SERVICE -> Replacing bulbs for Your Volvo V90 SUV Second Generation (2019-2026)

MAINTENANCE AND SERVICE  
Replacing bulbs  
CAUTION  
NOTE  
Bulb types vary depending on model and  
equipment level. If a light bulb15 breaks, it can  
be replaced by following the procedure  
shown in the Owner's Manual.  
Never touch the bulb glass with your bare  
fingers. Grease and oils from your fingers  
vaporize in the heat and will leave a  
deposit on the reflector, which may dam-  
age it.  
Bulbs for active curve lighting* contain  
traces of mercury and should therefore  
always be submitted to a certified Volvo  
service technician.  
If you are experiencing problems with any  
lights other than light bulbs, contact a work-  
Related information  
shop16  
.
Location of exterior lights (p. 575)  
•
NOTE  
If there is a problem with an LED17 light, the  
entire lamp unit will normally need to be  
replaced.  
Removing the plastic cover to replace  
bulbs (p. 575)  
•
If the error message persists after the  
defective bulb has been replaced, we rec-  
ommend a visit to an authorized Volvo  
workshop.  
Replacing the low beam headlight bulbs  
(p. 576)  
•
•
•
•
NOTE  
For information on lights not mentioned in  
the Owner's Manual, contact a Volvo  
dealer or a certified Volvo service techni-  
cian.  
Replacing the high beam headlight bulbs  
(p. 577)  
NOTE  
Replacing daytime running lights/front  
parking light bulbs (p. 578)  
Exterior lighting such as headlights and  
taillights may develop temporary conden-  
sation on the inside of the lens. This is nor-  
mal. All exterior lighting is designed to  
resist this. Condensation is normally ven-  
ted out of the lamp housing once the light  
has been lit for some period of time.  
Replacing front turn signal bulbs  
(p. 579)  
WARNING  
Replacing backup lights (p. 579)  
Replacing the rear fog light bulb (p. 580)  
Bulb specifications (p. 581)  
•
•
•
The vehicle electrical system must be in  
ignition mode 0 when bulbs are replaced.  
15  
Some vehicles do not have any light bulbs.  
An authorized Volvo workshop is recommended.  
LED (Light Emitting Diode)  
16  
17  
574  
* Option/accessory.  
MAINTENANCE AND SERVICE  
Removing the plastic cover to  
replace bulbs  
The headlight bulbs can be replaced without  
the assistance of a workshop, but before a  
bulb can be replaced, the plastic cover over  
the headlight needs to be removed.  
Location of exterior lights  
NOTE  
The vehicle's exterior lighting consists of sev-  
eral different bulbs. LED18 bulbs must be  
replaced by a workshop. An authorized Volvo  
workshop is recommended.  
To bear in mind when refitting the cover-  
ing:  
The pin in the clip must be pressed  
back completely before the clip is rein-  
stalled in the covering.  
•
Front bulbs (vehicles with halogen  
headlights)  
When the covering is reinstalled, the  
pin must be pressed in until the end  
surface is level with the surface of the  
clip.  
•
Related information  
Replacing bulbs (p. 574)  
•
Replacing the low beam headlight bulbs  
(p. 576)  
•
Replacing the high beam headlight bulbs  
(p. 577)  
•
•
•
•
–
Release the pins in the plastic cover's four  
clips by pressing them down with a  
screwdriver or similar object and remove  
the covering.  
Replacing daytime running lights/front  
parking light bulbs (p. 578)  
Low beams  
Replacing front turn signal bulbs  
(p. 579)  
High beams  
Daytime running light/parking light  
Turn signal  
Bulb specifications (p. 581)  
Front fog light/cornering illumination*  
(LED)  
18  
LED (Light Emmitting Diode)  
}}  
* Option/accessory. 575  
MAINTENANCE AND SERVICE  
||  
Rear bulbs  
Replacing the low beam headlight  
bulbs  
The low beam bulbs in the halogen head-  
lights can be changed without the help of a  
workshop.  
Before the bulbs can be replaced, the plastic  
covering over the headlight must be removed.  
CAUTION  
Never touch the bulb glass with your bare  
fingers. Grease and oils from your fingers  
vaporize in the heat and will leave a  
deposit on the reflector, which may dam-  
age it.  
Left headlight.  
1. Remove the low beam rubber cover from  
the headlight housing.  
Parking light (LED)  
Parking light (LED)  
Fog light  
2. Remove the connector from the bulb.  
3. Remove the bulb by pressing it slightly  
upward and then pulling it out.  
Backup light  
4. Insert the new bulb in the socket. The  
bulb's guiding pin should point straight  
up.  
Turn signal19  
Brake light (LED)  
5. Press the connector into place.  
Brake light ‒ central, high-mounted (LED)  
6. Put the rubber cover back in place.  
Related information  
Replacing bulbs (p. 574)  
•
•
•
Bulb specifications (p. 581)  
Lighting control and panel (p. 152)  
19  
Contact a workshop for replacement ‒ an authorized Volvo workshop is recommended.  
576  
MAINTENANCE AND SERVICE  
2. Remove the bulb by turning the bulb  
holder upward and then pulling it straight  
out.  
Related information  
Replacing the high beam headlight  
bulbs  
The high beam bulbs in the halogen head-  
lights can be changed without the help of a  
workshop.  
Location of exterior lights (p. 575)  
•
Removing the plastic cover to replace  
bulbs (p. 575)  
•
•
3. Carefully pry the plastic sleeve by the con-  
nector's locking lug to release it.  
Bulb specifications (p. 581)  
Before the bulbs can be replaced, the plastic  
covering over the headlight must be removed.  
4. Remove the connector from the bulb.  
5. Replace the bulb.  
CAUTION  
6. Position the bulb in the socket and turn it  
downward.  
Never touch the bulb glass with your bare  
fingers. Grease and oils from your fingers  
vaporize in the heat and will leave a  
deposit on the reflector, which may dam-  
age it.  
7. Put the rubber cover back in place.  
Related information  
Location of exterior lights (p. 575)  
•
Removing the plastic cover to replace  
bulbs (p. 575)  
•
Bulb specifications (p. 581)  
•
Left headlight.  
1. Remove the high beam rubber cover from  
the headlight housing.  
577  
MAINTENANCE AND SERVICE  
Replacing daytime running lights/  
front parking light bulbs  
Related information  
Location of exterior lights (p. 575)  
•
The daytime running light/parking light bulbs  
in the halogen headlights can be changed  
without the help of a workshop.  
Before the bulbs can be replaced, the plastic  
covering over the headlight must be removed.  
Removing the plastic cover to replace  
bulbs (p. 575)  
•
Bulb specifications (p. 581)  
•
•
Replacing the high beam headlight bulbs  
(p. 577)  
NOTE  
Daytime running lights/parking lights are  
easier to reach if the high beam headlight  
bulbs are removed. The high beam head-  
lights are mounted above and to the side of  
the daytime running lights/parking lights.  
Remove the high beam headlight bulb by  
turning the bulb holder upward and then  
pulling it straight out.  
Left headlight.  
1. Remove the daytime running light/parking  
light rubber cover from the headlight  
housing.  
2. Pull the daytime running light/parking  
light bulb holder straight out.  
3. Remove the bulb by pulling it straight out.  
4. Replace the bulb.  
CAUTION  
Never touch the bulb glass with your bare  
fingers. Grease and oils from your fingers  
vaporize in the heat and will leave a  
deposit on the reflector, which may dam-  
age it.  
5. Position the bulb holder in the socket and  
push it into place.  
6. If the high beam bulb holder has come  
loose, position it in the socket and turn  
downward.  
7. Put the rubber cover back in place.  
578  
MAINTENANCE AND SERVICE  
Replacing front turn signal bulbs  
Related information  
Replacing backup lights  
The light bulb for the backup light is located  
behind the panel in the tailgate.  
Location of exterior lights (p. 575)  
•
The turn signal bulbs in the halogen head-  
lights can be changed without the help of a  
workshop.  
Before the bulbs can be replaced, the plastic  
covering over the headlight must be removed.  
Removing the plastic cover to replace  
bulbs (p. 575)  
•
Bulb specifications (p. 581)  
•
1. Remove the panel on the inside of the tail-  
gate by turning both clips counterclock-  
wise a quarter-turn. Remove the panel.  
Place the panel in a safe location out of  
the way.  
Left headlight.  
1. Remove the turn signal rubber cover from  
the headlight housing.  
2. Press the retaining catches together and  
pull the bulb holder straight out.  
3. The bulb holder and bulb must be  
replaced as one unit.  
4. Position the bulb holder in the socket and  
push it into place.  
5. Put the rubber cover back in place.  
}}  
579  

Related Topics

MAINTENANCE AND SERVICE
Volvo's service program Engine compartment overview Start battery Fuses and fuseboxes Cleaning the interior Cleaning the exterior

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot