Get Transport of objects -> Boot floor Guide for Volkswagen Touareg SUV Third Generation (2018-2025)

Boot floor

Boot floor - Functions

Fig. 201 In the luggage compartment: Open the

luggage compartment floor.

Closing the luggage compartment floor

Opening the luggage compartment floor

– If necessary, open the luggage

compartment cover.

– Unhook the fastening strap → fig. 201 from

the upper edge of the luggage

compartment (arrow).

→

p. 267.

– Hook in the fastening strap → fig. 201

– Pull the handle → fig. 201 (magnified image)

in the sense of

the

and lower the pi-

of the luggage

compartment floor

under the luggage

compartment floor so →

arrow and lift the floor.

- If necessary, close the luggage compartment cover.

- To fasten the floor, unhook the fastening

strap → fig. 201 from the rear of the boot lid

and hook it onto the upper edge of the boot

lid (arrow).

→

p. 267.

NOTICE

Do not drop the luggage compartment floor

when closing it, but always guide it downwards

in a controlled manner. Otherwise, the trim or

the floor of the luggage compartment may be

damaged.

The following are examples of possible damage to the

lethal weapon.

Transport of objects

269

Separation netting

Reversible load floor

Unfold and fold the separation

netting

Fig. 202 In the luggage compartment: Raise the

removable load floor.

Removing the reversible load floor

– If necessary, open the luggage compartment

cover.

Fig. 203 Deploy the separation net.

→

p. 267.

– Pull the handle → fig. 202 (magnified image)

in the sense of

of the reversible load floor

the arrow and lift the

floor.

– Remove the reversible load floor

→ fig. 202

Turning the reversible load floor upside down

– If necessary, open the luggage compartment cover.

→

p. 267.

– Pull the handle → fig. 202 (magnified image)

in the sense of

of the reversible load floor

the arrow and lift the

floor.

– Pull the floor → fig. 202

by the handle, give it

Fig. 204 Folding the separation net.

turn it over and put it back in the case →

– To return the reversible floor to its original

position, pull it out by the side handles, turn

it upside down and put it back in place.

Before the separation net is installed in the

vehicle, it must be unfolded.

Deploying the separation network

NOTICE

Remove the separation net from the

corresponding bag and unroll it.

Do not drop the reversible load floor when

lowering it, always guide it down in a controlled

manner.

Unfold the cross rods

→ fig. 203 and the

net in the direction of the arrows

until you hear a "click"

Otherwise, the trim or the load

oor may be damaged

270

Instruction manual

Folding the separation net

– Hook the partition net into the right-hand roof

mounting by compressing the cross rod → fig.

– Press the unlocking button → fig. 204

and fold the cross rod in the direction of the

arrow while keeping the button pressed.

205

– Hook the two hooks of the partition net into

the lashing eyes in the luggage

compartment.

– Press the unlocking button → fig. 204

and fold the cross rod in the direction of the

arrow while keeping the button pressed.

→ fig. 205

and tighten the fastening belts

securely.

– Roll up the separation net and store it in its

bag.

Dismantling the separation net

securely in the

– Store the separation net bag

vehicle

– If necessary, remove the case cover → page

267.

– Loosen the securing straps of the

separation net.

Use the separation net

– Unhook the net hooks from the lashing rings

→ fig . 205

– Unhook the separation net from the housing.

com-

The right-hand roof bracket → f ig.

205 by priming the transverse rod.

– Unhook the partition net from the left-hand

roof housing.

– Fold up the separation net → page 270.

– If necessary, fit the luggage compartment cover.

→

p. 267.

WARNING

In the event of braking or an accident, objects

could be thrown out of the passenger

compartment and cause serious or fatal

injuries.

Fig. 205 In the luggage compartment: Fitting the

partition net behind the rear seat.

The function of the partition net is to prevent

objects carried in the luggage compartment

from being thrown into the passenger

● Check whether the cross rods are correctly

fitted.

compartment, e.g. in the event of braking.

● Always secure objects, even when the

separation net is correctly mounted.

The partition net can be mounted behind the

rear seat or, depending on equipment, behind

the front seats with the second row of seats

folded down.

● When the vehicle is in motion, do not

allow anyone to remain behind the

mounted partition net.

Assembling the separation net

NOTICE

The partition net can be mounted behind the

rear seat or, depending on equipment, behind

the front seats with the second row of seats

folded down.

Incorrect attachment of the separation net at

points not intended for this purpose can lead to

damage

– Unhook the seat cover from the top of the

rear seat backrest and roll it up.

– If necessary, remove the case cover → page

267.

– Unfold the separation net → p. 270.

– Hook the partition net into the left roof

bracket → Fig. 205 . Make sure to pull the

cross rod downwards beyond the upper

position.

Transport of objects

271

Transport of objects -> Boot floor for Your Volkswagen Touareg SUV Third Generation (2018-2025)

Related Topics

Transport of objects