Get Instruments -> Volkswagen information system Guide for Volkswagen Up 4 Door Second Generation (2019-2023)

If several warning reports are detected, the symbols will appear for several seconds, one

after another. The symbols will continue to appear until the faults are rectified.

Service interval display

First read and observe the introductoryinformation and safety warnings⇒

Introduction

The service display is shown on the instrument cluster ⇒ Fig. 10 or ⇒ Fig. 11②.

Service schedules at Volkswagen are divided into two categories, with oil change, e.g. interval

service, and without oil change, e.g. inspection service. This service interval display only provides

information on services that include oil change. The sticker on the door pillar of the vehicle and the

service schedule booklet provide information on all other services, for example, the next inspection

service or brake fluid service.

In vehicles with service dependent on the time/distance travelled, the service intervals are fixed.

Service

If a service is due, an acoustic signal will sound and a service reminder in text form

will

appear for a few seconds when the ignition is switched on. Volkswagen recommends that the

scheduled service should be carried out within the next 100 km (approximately 62 miles).

Resetting the service interval display

If the service was not performed by a Volkswagen dealership, the display can be reset in the

instrument cluster as follows:

Switch off the ignition.

Press and hold the

Restart the ignition.

Release the

button.

button and press it again briefly within approximately 10 seconds.

Do not reset the service interval display between service intervals otherwise incorrect data may be

shown.

The service message will go out after a few seconds once the engine is running or when the

button in the windscreen wiper level ⇒ Fig. 12① is pressed.

If the vehicle battery is disconnected for long periods, the system will not be able to calculate

the time when the next service is due. The service displays could then display incorrect information.

If this is the case then please observe the maximum service intervals shown in ⇒BookletService

schedule,.

Volkswagen information system

Introduction

This chapter contains information on the followingsubjects:

⇒ Using the displays in the instrument cluster

⇒ Multifunction display (MFD)

Various different displays can be accessed via the instrument cluster display once the ignition has

been switched on.

The scope of the displays in the instrument cluster depends on the vehicle electronics and the level

of vehicle equipment.

A qualified workshop can program and modify other functions depending on the vehicle equipment

level. Volkswagen recommends using a Volkswagen dealership for this purpose.

Additional information and warnings:

•

Instrument cluster ⇒ Instrument overview

Exterior mirrors ⇒ Mirrors

Driver assist systems ⇒ Driver assist systems

Radio ⇒BookletRadio,

WARNING

Accidents and injuries can occur if the driver is distracted.

Never open the displays in the instrument cluster while the vehicle is in motion.

•

In some vehicles other vehicle functions can be displayed on the screen of the portable

navigation device (delivered by Volkswagen) ⇒ Accessories, modifications, repairs and renewal of

parts.

After starting the engine with a discharged vehicle battery, or after the battery has been

changed, system settings (time, date, personal convenience settings and programming) may have

been changed or deleted. Check and correct the settings as necessary once the vehicle battery has

been sufficiently charged.

Using the displays in the instrument cluster

Fig. 12 The windscreen wiper lever: button ① to confirm and rocker switch ② to change the

display

First read and observe the introductoryinformation and safety warnings⇒

Introduction

Opening a display option

•

Switch on the ignition.

If a message or vehicle pictogram is displayed, press the

button ⇒ Fig. 12①.

Press the rocker switch ② up or down until the appropriate display option is shown.

Multifunction display (MFD)

First read and observe the introductoryinformation and safety warnings⇒

Introduction

The multifunction display (MFD) is equipped with two automatic memories: 1 - Trip memory and 2 -

Total journey memory. The number of the current memory on display will be shown in the lower

right-hand corner of the display.

When the ignition is switched on and memory 1 or 2 is shown on the

display, press the

button to switch between the two memories.

The memory collects the travel and fuel consumption data from the moment

the ignition is switched on until it is switched off.

If the journey is interrupted for more than two hours, the memory is

automatically deleted. If the journey is continued within two hours of the

ignition being switched off, the new values will be added to the existing trip

recorder.

Trip memory

Depending on which instrument cluster is installed, the memory collects

journey data for any number of individual journeys up to a total of 19 hours

and 59 minutes travel time or 1,999.9 km (miles) distance travelled. Once

these total limits have been reached, the memory will be deleted

automatically and begin again at 0.

Total journey

memory

Possible displays

Time^a)

Function

Current time in hours (h) and minutes (min).

Driving time in hours (h) and minutes (min) that has elapsed since

the ignition was switched on.

Driving time

While the vehicle is in motion, current consumption is displayed

in l/100 km. When the engine is running and the vehicle is

stationary it is measured in litres/hour or, in vehicles with gas

engines, in kg/h.

Current fuel consumption

The average fuel consumption will be shown in l/100km or, in

vehicles with gas engines, in kg/100 km after a distance of

Average fuel consumption approximately 100 metres has been travelled. The display will show

dashes until this point. The displayed values will be updated

approximately every 5 seconds.

Approximate calculation of the distance in km that can still be

travelled with the current fuel level under the current driving

conditions. One factor used for calculating this figure is the current

level of fuel consumption.

Fuel range

In natural gas engines: the value with the

symbol shows the

symbol shows

total distance in petrol mode. The value with the

the total distance in petrol mode.

Distance driven

The distance travelled in km since the ignition was switched on.

Function

The average speed will be shown after a distance of approximately

100 metres has been travelled. The display will show dashes until

this point. The displayed values will be updated approximately

every 5 seconds.

Average speed

Digital speed display

Current vehicle speed displayed digitally.

Current temperature of the coolant temperature displayed digitally.

If the --.- appears in the instrument cluster display and the

red

Digital coolant temperature

display

warning light flashes, there is a fault in the engine cooling system.

Do not drive on! Seek expert assistance.

Digital outside temperature

display

Current outside temperature displayed digitally.

If the saved speed (within the range of 30 km/h (18 mph) and

250 km/h (155 mph)) is exceeded, an acoustic warning will be

given, along with a visible warning if required.

Speed warning --- km/h

Switching between displays

•

Press the rocker switch ⇒ Fig. 12② on the windscreen wiper lever.

Setting the clock^a)

•

Press and hold the

button in the windscreen wiper lever ⇒ Fig. 12① to mark the hour

display so that it flashes.

Use the rocker switch on the windscreen wiper lever ⇒ Fig. 12② to make the settings. To do

this, push the rocker switch up or down to increase or decrease the hours display.

Press the

button in the windscreen wiper lever again briefly to select the minute display

so that it flashes.

Use the rocker switch on the windscreen wiper lever to make the settings. To do this, push the

rocker switch up or down to increase or decrease the minutes display.

Press the

button on the windscreen wiper lever briefly to finish setting the clock.

Settings for the clock can also be made directly using the setting buttons on the instrument cluster

⇒ .

Saving a speed for the speed warning

•

Select the Speed warning --- km/h display.

•

Press the

button on the windscreen wiper lever to save the current speed and activate

the warning system.

•

If necessary, use the rocker switch on the windscreen wiper lever within approximately 5

seconds to set the desired speed. Then press

is now saved and the warning is activated.

again or wait a few seconds. The speed

To deactivate, press

. The set speed will be deleted.

Deleting memory 1 or 2 manually

•

Select the memory that you wish to delete.

•

Press and hold the button for approximately 2 seconds ⇒ Fig. 12①.

In some vehicles other functions in the multifunction display can be displayed on the screen

of the portable navigation device (delivered by Volkswagen) ⇒ Accessories, modifications, repairs

and renewal of parts.

^a)Type 2 instrument cluster only ⇒ Instrument cluster.

Before the journey

Before setting off

Driving tips

Introduction

This chapter contains information on the followingsubjects:

⇒ Preparing for a journey and driving safely

⇒ Driving abroad

⇒ Driving through water on roads

Depending on where the vehicle is used, it may be advisable to have an engine and transmission

guard installed. An engine and transmission guard can reduce the risk of damage to the vehicle's

underbody and engine oil sump, for example when driving over kerbs, driveways or unsurfaced

roads. Volkswagen recommends using a Volkswagen dealership for this purpose.

Instruments -> Volkswagen information system for Your Volkswagen Up 4 Door Second Generation (2019-2023)

Related Topics

Instruments

Popular Owner Manuals

Latest Owner Manuals