2005-2017 Aston Martin Vantage 2 Door Vehicle Security User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Vehicle Security for Your Aston Martin Vantage 2 Door Third Generation (2005-2017)

Vehicle Security
Introduction ...............................................................................2.2
Aston Martin Tracking ................................................................2.2
Emotion Control Unit .................................................................2.5
Emergency Key...........................................................................2.6
Unlocking and Opening .............................................................2.7
Locking ......................................................................................2.8
Master Locks ..............................................................................2.8
Trunk Lid ...................................................................................2.9
Deadlocking.............................................................................2.11
Automatic Lock ........................................................................2.11
Approach Light.........................................................................2.12
Homesafe ................................................................................2.12
Alarm.......................................................................................2.12
Reduced Guard........................................................................2.13
Passive Anti-Theft System .........................................................2.14
Garage Door Opener ...............................................................2.15
Personalisation .........................................................................2.18
2.2
Vehicle Security
Introduction
This vehicle is protected by an electronic security system which
includes:
• Remote arm and disarm
• Perimeter sensing
• Remote door, trunk lid, fuel flap release lock and unlock
• Guard reduction mode
• Alarm siren with battery backup
1
• Random code encryption to prevent electronic scanning or
grabbing of the vehicle key identity code
• Interior movement sensor
2
• Tilt Sensor
2.
Vehicle protection is enhanced by a Passive Anti-Theft System (PATS)
which provides engine immobilisation if the wrong vehicle key is
used.
When the security system is armed, any attempt to forcibly open a
door, the trunk lid or the hood will result in full alarm operation.
Garage Door Opener
As a security precaution make sure that all programming is erased in
the HomeLink system before selling this vehicle (Refer to ’Garage
Door Opener’, page 2.15).
Aston Martin Tracking
Option - Not available in all markets.
The Aston Martin Tracking system is a stolen vehicle tracking system.
It uses the latest Global Positioning System (GPS) and Global System
for Mobile communications (GSM) technology providing pinpoint
accuracy and unparalleled service levels.
The system, which is discretely installed in the vehicle, is an easy-to-
use system that provides the following important features:
Automatic Driver Recognition
Alerts the Aston Martin Tracking Secure Operating Centre
immediately if your vehicle is stolen, even if the thief has your keys.
Engine Start Inhibit
Activated by the Secure Operating Centre with Police authorisation,
to prevent the engine from being restarted.
Tamper Alert
Activated when the system battery is disconnected or discharged, or
when the system wiring is cut.
Tow-Away Alert
Triggered when motion is detected with the ignition switched off and
the driver card is not present.
1.
Markets where audible sirens are permitted.
2.
Option.
2.3
Vehicle Security
System Health Check
Regular automatic self diagnostic check.
Transport Mode
Set by the Secure Operating Centre when the vehicle owner has
confirmed the vehicle is being transported. This will prevent false
alerts being generated.
Vehicle Servicing Mode
Set by the Secure Operating Centre when the vehicle has been given
to the Aston Martin Dealer for maintenance.
Theft History
Minute by minute theft log helps Police secure convictions.
Pinpoint GPS Tracking
Accurate to within 10 metres.
International GSM Coverage
Roaming SIM card gives coverage across more than 180 countries.
European Coverage
Local language Police liaison and stolen vehicle recovery across
Europe.
Countries covered by Aston Martin Tracking System:
Albania, Austria, Belarus, Belgium, Bosnia and Herzegovina,
Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France (Monaco), Germany, Greece, Hungary, Ireland, Italy
(Vatican City, San Marino), Latvia, Lithuania, Luxembourg,
Macedonia, Malta, Montenegro, Netherlands, Norway, Poland,
Portugal, Romania, Russia, Serbia, Slovakia, Slovenia, South Africa,
Spain (Andorra, Gibraltar), Sweden, Switzerland (Liechtenstein),
Turkey, Ukraine and United Kingdom.
Insurance Accreditation
Conforms to the highest European accreditations for stolen vehicle
tracking systems - Thatcham, Incert (formerly Assuralia) and SCM and
is approved by major insurers.
Aston Martin Approved
The only vehicle tracking system approved for all Aston Martin
vehicles.
How the System Works
The Aston Martin Tracking system is supplied with two unique driver
cards. An authorized driver must have a driver card in their
possession when using the vehicle.
Do not leave the driver card inside the vehicle or with the vehicle
key. It should be kept in a safe place and always separately from your
vehicle keys.
The system automatically arms itself after the vehicle ignition has
been switched off for 70 seconds and the driver card is out of range
(approximately 3 metres).
The system will automatically disarm itself when the driver card is
bought back in range of the vehicle.
If your vehicle is driven approximately 100 metres and the driver card
has not been detected, a silent alert is transmitted to the Secure
Operating Centre to inform the advisors of a potential unauthorized
movement of your vehicle. The advisors then contact you.
To avoid an alert being generated, if the engine has been started and
the driver card is not in your possession, switch the ignition off and
call the Secure Operating Centre for advice.
2.4
Vehicle Security
The system will additionally:
• Send an alert if your vehicle is lifted or towed away without the
keys.
• Send an alert if your vehicle battery is disconnected or
discharged.
• Send an alert if the GPS antenna has been disconnected.
• Send a monthly health check message to the Secure Operating
Centre to confirm full system functionality.
Please consult your Aston Martin Dealer for details and subscription
rates.
If your Vehicle is Stolen
After an alert has been received, the Secure Operating Centre
advisors attempt to contact you using the telephone number(s) that
you supplied at the time of registration. A minimum of two telephone
numbers must be provided at the time of activation of the contract.
The Police are not contacted until the advisors have spoken with you.
This is to comply with Police procedures so that Police time is not
wasted with false alarms.
Once the theft has been confirmed with you, the advisors will ask you
to contact the Police to report the theft and to call the advisor back
immediately with a Police incident number. Receipt of an alert does
not constitute a confirmed theft, as Police Forces require key holder
verification of a theft.
The Secure Operating Centre then liases with the relevant Police
Force to seek to recover your vehicle.
If your vehicle is outside the UK, the Secure Operating Centre work
with the Police in their local language across Europe to recover your
vehicle quickly.
In order to prevent your vehicle being moved following a theft, the
Secure Operating Centre under instruction from the Police, may
temporarily prevent the vehicle's engine from restarting.
Once the Police have secured the stolen vehicle, arrangements are
made with you for the vehicle to be collected. The Police may require
it to be taken to a secure compound for further investigation.
You will be liable for any statutory Police recovery and storage
charges, payable directly to the Police.
Additional Information
False Alarms
To avoid unnecessary alerts, contact the Secure Operation Centre to
inform them of any potential false alarm. Excessive false alerts may
result in a charge.
Damage Check
If you are involved in an accident or if your vehicle battery has been
disconnected for any reason (for example, body work repair or paint
re-spray), you must call Aston Martin Tracking Customer Services so
that they can test the system to check that it is still functioning
correctly.
2.5
Vehicle Security
Change of Details
Should any of your personal details change, you must call Aston
Martin Tracking Customer Services. For example:
• Changing the registration plate on the vehicle.
• Selling the vehicle.
• Change of address.
• Change of mobile phone number.
• New owner buying a pre-owned vehicle already fitted with Aston
Martin Tracking System.
Contact Details
All the relevant contact details for your specific country are contained
in your registration information. For any additional information,
contact your Aston Martin Dealer.
Remember to keep all contact details and information safe and
not in the vehicle otherwise you will not be able to refer to it if your
vehicle is stolen.
Emotion Control Unit
The vehicle is supplied with three vehicle keys
1
(Emotion Control
Units), a glass key, a spare key and an emergency key.
Keep the spare key in a safe place. Do not leave a vehicle key in the
vehicle when unattended.
If a vehicle key is lost, contact your Aston Martin Dealer.
FCC Warning: ‘Note’ - Changes not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC - Radio Frequency Devices
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
1.
Manufactured by 8D33-70290-BG.
2.6
Vehicle Security
Vehicle Key Security Functions
[1] LOCK: Press and release for one step
vehicle locking and to arm the security
system. The vehicle will deadlock after 25
seconds (Refer to ’Deadlocking’, page 2.11).
[2] UNLOCK: Press and release to unlock the
driver’s door only. Press and release twice,
within three seconds, to unlock all doors.
[3] TRUNK OPEN: Press once to release the
trunk lid catch (Refer to ’Trunk Lid’, page
2.9).
[4] APPROACH LIGHT: Press to set the front,
rear side and interior lamps to ON (Refer to
’Approach Light’, page 2.12).
Emergency Key
In the unlikely event that either the vehicle
key fails to operate or the vehicle battery is
fully discharged use the emergency key to
lock or unlock the vehicle.
Insert the emergency key in the door lock
and turn fully towards the front of the
vehicle, then release, to centrally lock the
vehicle, disable the trunk lid and fuel flap
release switches. The security system will
not arm.
To centrally unlock the vehicle, enable the
trunk lid and fuel flap release switches, turn fully towards the rear of
the vehicle, then release. If the security system was armed, the alarm
will start.
To stop the alarm insert the vehicle key (even if the vehicle key has
lost all power) into the ignition control and move to position ‘II’
(ignition ON).
If the vehicle battery is fully discharged the emergency key will
only lock or unlock a door.
Even if the vehicle key has lost all power it will start the engine if
required.
Memory seats: The front seats and door rear view mirrors will not
move to a preset position if the vehicle is unlocked using the
emergency key.
If the emergency key is lost, contact your Aston Martin Dealer.
2.7
Vehicle Security
Unlocking and Opening
Stand within 16 ft of the vehicle, point the vehicle key towards the
vehicle and press the UNLOCK button once to unlock the driver's
door and disarm the security system (the direction indicators will flash
twice). Press twice to unlock the passenger door and enable the trunk
lid catch and fuel flap release button.
Push at point A and grab the
emerging door release. Pull the
door release to open the door.
If a door is opened while driving
a warning sound will be heard
until the door is closed.
If preferred you can unlock all
doors and enable the trunk lid
and fuel flap release switches
with one press of the button (Refer to ’Personalisation’, page 2.18).
For ease of use at night white LEDs are incorporated into the door
handles. An LED will come ON in the door handles when the vehicle
is unlocked. A door LED will go OFF once the door is opened. If a
door is not opened the LEDs will go OFF after two minutes.
If the vehicle has been opened using the spare key and the driver
seat or door rear view mirrors have been adjusted, the seat and door
rear view mirrors will move to the positions memorized by the key
which is being used (Refer to ’Seat Memory Function’, page 3.5).
As the vehicle is unlocked, the interior lamps will come ON for
five minutes. The lamps will go OFF 30 seconds after doors are closed
or when the vehicle is started.
If the door is left open the door puddle lamp will go OFF after
eight minutes.
Unlocking From Inside the Vehicle
If reduced guard was not set to ON before locking the vehicle,
deadlocking, interior movement and tilt sensors (optional)
1
are
enabled. Passengers will not be able to unlock a door from the
inside.
If reduced guard or automatic lock was set to ON before the vehicle
was locked, one pull of a door handle will centrally unlock the doors,
a second pull of the door handle will open that door.
(Refer to ’Automatic Lock’, page 2.11).
(Refer to ’Reduced Guard’, page 2.13).
Vehicle unlock from inside can be set to automatic unlock when the
vehicle key is removed from the ignition control. With automatic
unlock ON only one pull of a door handle will open that door (Refer
to ’Personalisation’, page 2.18).
When opening a door from inside the vehicle after reduced guard has
been set to ON, the security system alarm will start. Press the
UNLOCK button on the vehicle key to stop the alarm (there is
approximately a ten second delay before the alarm is stopped).
1.
Option.
2.8
Vehicle Security
Locking
If passengers are to stay in the vehicle after it has been locked,
reduced guard must be set to ON before locking. This will let a
passenger open a door from inside the vehicle.
Make sure that all the doors, the trunk lid and the hood are closed
(the vehicle will not lock if a door is left open). Stand within 5 m of
the vehicle, point the vehicle key towards the vehicle and press the
LOCK button once to lock the doors, disable the trunk lid and fuel
flap release switches and arm the security system. The direction
indicators will flash once as the security system is armed (Refer to
’Personalisation’, page 2.18). The driver's seat and both door rear
view mirror positions are memorized and will be recalled the next
time the vehicle is opened using the same vehicle key.
The security system will arm and the doors will deadlock after
25 seconds.
If the vehicle is locked with the trunk lid open, the vehicle will
lock and arm but deadlocking, tilt and interior movement sensors
1
will not operate. Close the trunk lid to arm the complete security
system.
Automatic Re-locking
If the vehicle is locked and then unlocked but a door or the trunk lid
is not opened within two minutes, the vehicle will automatically lock
and arm again.
Master Locks
All doors, fuel flap and trunk lid
release switches may be locked
and unlocked by using the master
lock switch (A). Press the switch to
lock. Press again to unlock.
If the vehicle is locked using the
master lock switch, one pull of a
door handle will centrally unlock
the doors, a second pull of the
door handle will open that door.
The master lock switch will operate for seven minutes after the
vehicle key has been removed from the ignition control, if the vehicle
is not locked using the vehicle key.
The master lock switch will not operate if the vehicle has been locked
from the outside.
Operation of the master lock switch will override automatic lock
(Refer to ’Automatic Lock’, page 2.11).
1.
Option.
2.9
Vehicle Security
When the vehicle is unlocked using the master lock switch the
LED in each door handle will come ON (for 10 seconds or until the
door is opened). This may aid access for passengers at night time.
In the event of a vehicle accident the doors will automatically
unlock.
Trunk Lid
To Open the Trunk Lid
Press the TRUNK OPEN button
on the vehicle key once to
enable the release catch, then
press the trunk lid button (A) and
lift the lid. Press the button twice
(within three seconds) to enable
the trunk lid catch and release
the lid. Lift the lid.
If the vehicle is locked and armed the security system will disarm
and the direction indicators will flash twice when the trunk is opened.
The doors will stay locked (Refer to ’Personalisation’, page 2.18).
Opening from Inside the Vehicle
Pull back on the trunk lid release
switch (B). The trunk lid catch will
release
1
. Lift the lid.
1.
The trunk lid release switch becomes the roof raise and lower switch on the
Volante.
2.10
Vehicle Security
To Close the Trunk Lid
Grasp the leather pull (C) and pull
the trunk lid down, then push the
trunk lid down and make sure
that its catch engages. Once the
catch engages, it automatically
closes. If the trunk lid is slammed
shut, this is overridden. Press the
LOCK button on the vehicle key
to lock the lid. The direction
indicators will flash once as the
security system is armed (Refer to ’Personalisation’, page 2.18).
Always make sure that the trunk lid is securely closed after use.
The trunk interior lamps will stay ON for seven minutes if the trunk
lid is left partially open and the vehicle key is removed from the
ignition control.
Vehicle Locked - Trunk Lid Open
To use a battery conditioner the trunk lid has to be left open
(trunk lid down but not latched).
If the vehicle is locked while the trunk lid is open, the vehicle will lock
and arm (deadlocking, tilt and interior movement sensors
1
will not
operate). If the trunk lid is then closed (latched) deadlocking, tilt and
interior movement sensors will operate and the whole vehicle will be
locked and armed.
Trunk Lid Emergency Open
The trunk lid can be opened
from inside the trunk by pulling
the luminous emergency release
handle (D).
1.
Option.
2.11
Vehicle Security
Deadlocking
If passengers are to stay in the vehicle after locking, reduced
guard must be ON before locking.
The vehicle will automatically deadlock after 25 seconds after arming
the security system. When the vehicle is deadlocked, the doors
cannot be opened from the inside by pulling the interior door handle.
To open the doors use the vehicle key.
Automatic Lock
When automatic lock is set to ON the doors and the trunk lid will
automatically lock as vehicle speed reaches 4mph. This function
prevents unwanted access to the vehicle when stopped at traffic
lights, etc.
Press MENU on the centre console. Navigate to <Car settings...>
Enter <Lock settings...> Enter <Automatic settings...>. Select
<Doors auto lock> or <Doors auto unlock on key out>. Press
ENTER to toggle between ON and OFF.
Then press and hold BACK to accept and return to the main screen.
<Doors auto lock>: Set to ON: Doors and the trunk lid
automatically lock when the vehicle moves off.
Set to OFF: Doors and the trunk lid will not lock when the vehicle
moves off.
<Unlock on key out>: Set to ON: The front doors and the trunk lid
automatically unlock when the vehicle key is removed from the
ignition control.
Set to OFF: One pull of a door handle will centrally unlock all doors,
a second pull of the door handle will open that door.
Automatic lock is factory set to ON (Refer to ’Personalisation’,
page 2.18).
In the event of a vehicle accident all doors will automatically
unlock.
2.12
Vehicle Security
Approach Light
When approaching the vehicle the side and interior lamps can be set
to ON by pressing the APPROACH LIGHT button on the vehicle key.
The time that the lamps stay ON is programmable (Refer to
’Personalisation’, page 2.18).
Homesafe
When exiting the vehicle and the vehicle key has been removed from
the ignition control, flash the main beam (pull the left side stalk up
and release without latching) to set homesafe ON. The main beam
and rear lamps will then stay ON for a determined amount of time
and then go OFF. The time that the main beam and rear lamps stay
ON is programmable (Refer to ’Personalisation’, page 2.18).
Alarm
When the alarm has started a siren will be heard for a 25 seconds
cycle (ten cycles maximum) and the direction indicators flash for
five minutes after which the security system returns to the armed
state. The doors and trunk lid will stay locked throughout.
Markets where visible alarm signals and audible sirens are
permitted.
Stop the alarm at any time by pressing the UNLOCK button on the
vehicle key or by inserting the vehicle key into the ignition control
(position ‘II’). There is approximately a ten second delay before the
alarm is stopped).
Insert the key to position ‘II’ by using
the flat of a finger, as shown.
2.13
Vehicle Security
Interior Movement Sensor
Optional
When the vehicle is locked and armed the interior movement sensor
will sense movement inside the vehicle. If movement is detected it
will start the alarm.
Tilt Sensor
Optional
When the vehicle is locked and armed the tilt sensor will sense if the
vehicle is tilted, for example, if the vehicle is being raised on a jack.
If vehicle tilt is detected it will start the alarm.
Reduced Guard
Warning: If a passenger is to stay in the vehicle after it has
been locked, reduced guard must be set to ON before locking. In
an emergency this will let a passenger open a door from inside
the vehicle.
When reduced guard is ON deadlocking, interior movement and tilt
sensors (option) are set to OFF. This will let a passenger open a door
from the inside by pulling the interior door handle and a passenger
or animals to be left in the vehicle with the security system armed.
If a door is opened from the inside, while reduced guard is ON, the
security system alarm will start. Press the UNLOCK button on the
vehicle key to stop the alarm at any time.
Reduced guard is set by using the car settings menu. Press MENU on
the centre console. Navigate to <Car settings...> Enter <Reduced
guard...>. Select <Activate once> or <Ask on exit> and press
ENTER to toggle between ON and OFF. Then press and hold BACK
to accept and return to the main screen.
<Ask on exit>: Set to ON: Each time the vehicle key is moved from
ignition position 'II' (ignition ON) to ignition position 'I' or '0' the
message PRESS ENTER TO REDUCE GUARD. PRESS EXIT TO
CANCEL will show in the message centre. The message will time out
after one minute and reduced guard will not come ON.
Set to OFF: No message will show and reduced guard will not come
ON.
<Activate once>: Set to ON: Reduced guard will come ON for one
time. Set to ON each time reduced guard is required.
Set to OFF: Reduced guard will not come ON.
Reduced guard stays ON until the vehicle key is inserted in the
ignition control and moved to position 'II' (ignition ON).
2.14
Vehicle Security
Passive Anti-Theft System
The Passive Anti-Theft System (PATS) is a fully automatic engine
immobilizer.
If a vehicle key is lost, a duplicate key can be created and
programmed from the spare key by your Aston Martin Dealer.
Starting the Engine
When the security system is disarmed and the vehicle key is in the
ignition control, the PATS controller sends a signal to the vehicle key.
The vehicle key must respond with a valid code before engine start
will be enabled. If a valid code is received, the ignition system will
operate normally. If the vehicle key code is not received, or is invalid,
engine start stays disabled.
PATS Status
The PATS system state is
shown by the red symbol on
the instrument cluster (A).
Fault Mode
If the status symbol continues flashing when the ignition is set to ON,
the vehicle will stay immobilized.
Should this situation arise try removing and then inserting the vehicle
key back to position ‘II’ in the ignition control. If this is unsuccessful
try the spare key. If successful, get a replacement for the faulty vehicle
key. If problems continue with the vehicle key, consult your
Aston Martin Dealer.
Ignition Action (Valid code)
ON Symbol comes ON for three seconds.
OFF Symbol will flash.
OFF and the vehicle key
removed from the ignition
control
Symbol will flash for five minutes or one minute
after the vehicle is locked using the vehicle key.
2.15
Vehicle Security
Garage Door Opener
The garage door opener (HomeLink® Universal Transceiver)
operating buttons and transceiver are located in the interior rear view
mirror.
The transceiver can be programmed to transmit the radio frequencies
of up to three different transmitters used to operate garage doors,
entry gates, home lights, security systems, or other radio frequency
operated devices.
A full list of radio frequency operated devices can be either
obtained via the HomeLink Hot-line or through the HomeLink
compatibility list which is provided on the HomeLink website.
For information, or for assistance, contact your Aston Martin Dealer.
Alternatively contact HomeLink directly at or
call the HomeLink Hot-line:
Toll-free: 008000 0466 354 65
or
+49 6838 907-277 (In certain countries difficulties may be
experienced trying to reach the toll-free number by some providers.)
Warning: Do not use the transceiver with any garage door
opening system that lacks the safety stop and reverse feature as
required by safety standards. A garage door opening system
which cannot detect an object, signalling the door to stop and
reverse, does not meet current safety standards. Using a garage
door opening system without these features increases risk of
serious injury or death.
Warning: When programming the transceiver to a garage
door opening system, make sure that people, the vehicle and
objects are out of the way to prevent potential harm or damage
as the gate or garage door will operate during the programming.
Keep the original transmitter for future use or programming
procedures if, for example, you purchase a new vehicle.
This device may suffer from interference if operated in the vicinity
of a mobile or fixed station transmitter. This interference is likely to
affect the hand-held transmitter as well as the in-vehicle transceiver.
The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to
operate the equipment.
Programming
Step 1 erases all programming. It only requires completing if
programming HomeLink for the first time or when erasing all existing
programming. It does not have to be followed to program the other
HomeLink buttons.
The HomeLink buttons can be reprogrammed individually but not
individually erased. Step 1 must be completed to erase all
programming.
1. Press and hold the two outer
HomeLink buttons, releasing
only when the HomeLink LED
begins to flash after 20 seconds.
All three buttons are now
cleared. The HomeLink system
is now in setting mode.
As a security precaution make
sure that all programming is
erased in the HomeLink system before selling this vehicle.
2.16
Vehicle Security
2. Hold the original remote control of the device to be
programmed at a distance of 4-12 inches away from the
HomeLink transmitter unit keeping the LED in view all the time.
The distance between the remote control and the transmitter
unit depends on the system being programmed. You may
require several attempts at different distances. Maintain each
setting position for at least 15 seconds before trying out another.
3. Using both hands,
simultaneously push the
remote control button
and the desired button (1,
2 or 3).
4. The LED will flash, first
slowly and then rapidly.
When the LED flashes
rapidly, release both
buttons. The rapid
flashing LED shows
successful programming of the new frequency signal.
Operation
The vehicle should be within the operating range of the gate or garage
door opener and the ignition should be ON.
The HomeLink system operates the garage door opener (or other
device) in exactly the same way as the original remote control.
When you have programmed the
HomeLink system, press the
appropriate button 1, 2, or 3 on the
control panel to operate the garage
door opener.
The LED will come ON when the
button on the control panel is
pressed.
For convenience, the original remote control of the device may
also be used at any time.
In the case of a standard code, the HomeLink LED is constantly ON
throughout the transmission process. For use with compatible
systems, no further action is necessary.
If HomeLink now does not operate the garage door opener (or other
device), this may be because the original remote control has a rolling
code feature.
Rolling Code Synchronisation
Check, by going through the following steps, whether or not the
garage door opener (or other device) is equipped with a rolling code
feature.
• Look in the garage door opener manual for clarification
• The remote control apparently programs HomeLink but
HomeLink does not operate the garage door opener
• Press and hold down the programmed HomeLink button.
With a rolling code system, the HomeLink LED flashes quickly for
a short time and then stays ON constantly for two seconds. This
pattern repeats itself for up to 20 seconds
If HomeLink was programmed with a rolling code system, then after
the end of the programming period it must be synchronized with this
system again before it will function correctly.
Follow the instructions below for Rolling Code Synchronisation (the
procedure will take less time with a second person to help).
2.17
Vehicle Security
The vehicle must be within operating range of the garage door
opener and the ignition set to ON. Make sure you comply with the
safety instructions even when synchronising the rolling code.
1. Locate the Training button (programming button) on the garage
door opener motor head unit. Exact location and colour of the
button may vary by gate or garage door opener brand (refer to
the operating instructions of the garage door opener ‘Training
additional remote controls’).
2. Press the Training button (programming button) on the garage
door opener motor head unit (which will usually set a ‘training’
LED to ON).
Following step 2, there are typically 30 seconds in which to
initiate step 3.
3. Firmly press and release the programmed HomeLink button.
Press and release the HomeLink button a second time to
complete the training process. (Some garage door openers may
require this procedure a third time to complete the training).
The garage door opener should now recognize the HomeLink signal
and operate when the HomeLink button is pressed.
The next two buttons may now be programmed if this has not
previously been done.
Reprogramming
If a HomeLink button has been programmed to operate a device, and
you now wish to use this button to operate a different device,
proceed as follows.
This procedure will erase the existing programming of the respective
HomeLink button.
1. Press the appropriate HomeLink button 1, 2, or 3 which
requires reprogramming and keep holding it for about 20
seconds until the LED starts flashing slowly. Do not release until
step 4 has been completed.
2. When the LED begins to flash slowly (after approximately 20
seconds), hold the remote control of the device you wish to use
approximately 4-12 inches away from the HomeLink transmitter
unit - keeping the LED in view.
The distance between the remote control and the HomeLink
transmitter unit depends on the system being learned. You may
require several attempts at different distances. Maintain each
setting position for at least 15 seconds before trying out another.
3. Now press the remote control and keep it pressed.
4. The HomeLink LED will flash, first slowly and then rapidly.
When the LED begins to flash rapidly, release both buttons.
2.18
Vehicle Security
Personalisation
A number of security functions can be personalized.
[1] ON/OFF: Infotainment centre ON and OFF.
[2] SCREEN: Shows options, menus and information.
[3] TUNING: Turn (left or right) to navigate in the menus.
[4] MENU: Opens the main menu.
[5] ENTER: Select in the menu or open a selection.
[6] JOYSTICK: Navigate in the menus.
[7] BACK: Navigate back in the menu or cancel a selection.
Selection
With the vehicle key in ignition position 'I' or 'II', press MENU and
navigate to the required setting and press ENTER. Use the JOYSTICK
to make a selection and press ENTER to accept.
Menu
1) Car settings...
1) Reduced guard...
1) Activate once
2) Ask on exit
2) Mirror settings...
1) Auto mirror fold flat enabled
1) Auto
2) Passenger only
3) Passenger and driver
3) Lock settings...
1) Automatic settings...
1) Doors auto lock
2) Doors auto unlock on key out
2) Doors unlock...
1) All doors
2) Driver door, then all
4) Light settings...
1) Lock confirm. light
2) Unlock confirm. light
3) Approach light duration...
4) Homesafe light duration...
1) 30, 60 or 90 seconds
5) Information...
1) VIN number...

Related Topics

Introduction Aston Martin Tracking Emotion Control Unit Emergency Key Unlocking and Opening Locking Master Locks Trunk Lid Deadlocking Automatic Lock Approach Light Homesafe Alarm Reduced Guard Passive Anti-Theft System Garage Door Opener Personalisation

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot