Get Seats and storage Guide for Audi A5 4 Door First Generation (2007-2013)

Seats and storage70

Seats and storage

Manual adjustment of front seats

Applies to vehicles: with manual seat adjustment

Seat adjuster controls

There are several seat adjustment functions for your

comfort and convenience

Some of the controls shown are only fitted on certain models or are

optional extras.

Adjuster controls

Moves seat backwards or forwards

Thigh support*

Adjusts angle of seat cushion*

Adjusts lumbar support*

Adjusts seat height

Adjusts backrest angle

Applies to vehicles: with manual seat adjustment

Seat adjustment

It is possible to adjust the position and shape of the seat

manually so that you can travel in a safe and comfortable

sitting position.

Before adjusting your seat, please read and observe the

warnings ⇒ .

Moving seat backwards or forwards

– Lift the lever ⇒ fig. 72 and move the seat to the

desired position.

– Then release the lever and move the seat further until

the catch engages.

Extending or shortening the thigh support*

– Lift the control below the seat cushion. The front seat

cushion will spring forward.

– Slide the seat cushion back to the normal position after

each use.

Adjusting angle of seat cushion*

– Pull the lever ⇒ fig. 72 up or down repeatedly (i.e.

pump the lever).

Adjusting contour of lumbar support*

– Press the front or rear part of the adjuster switch to

increase or decrease the curvature of the lumbar support

as required.

Fig. 72 Adjuster

controls on driver's

seat

document_0900452a8179700c.book Seite 70 Donnerstag, 22. März 2007 10:19 10

Seats and storage 71

Controls Safety Driving tips General maintenance Self-help Technical data

Adjusting height of lumbar support*

– Press the top or bottom part of the adjuster switch to

move the lumbar support upwards or downwards as

required.

Raising or lowering the seat

– Pull the lever ⇒ page 70, fig. 72 up or down repeat-

edly (i.e. pump the lever).

Adjusting backrest angle

– Lean forwards to take your weight off the backrest.

– Turn the adjuster wheel ⇒ page 70, fig. 72 to set the

angle of the backrest as required.

WARNING

• Never adjust the driver's seat when the vehicle is moving - this

could lead to an accident.

• Be careful when adjusting the seat height. Careless or uncon-

trolled use of the seat adjustment can cause injuries.

• Do not drive with the backrests of the front seats reclined too

far as otherwise the seat belt and airbag could fail to restrain the

wearer properly in an accident, possibly leading to injury.

Applies to vehicles: with manual seat adjustment

Easy-entry function

The easy-entry function gives improved access to the rear

seats.

Folding down backrest and moving front seats

forwards

– Pull up the lever ⇒ fig. 73.

– Keep holding the lever and fold down the backrest.

– Let go of the lever and push the seat forwards.

Moving front seat back and returning backrest

to an upright position

– Push the front seat back before you return the backrest to

an upright position. Otherwise, it will not be possible to

move the seat back to its original position.

WARNING

Before you drive off, always make sure the front seats are upright

and securely locked in position.

Fig. 73 Driver's seat:

Lever on backrest

document_0900452a8179700c.book Seite 71 Donnerstag, 22. März 2007 10:19 10

Seats and storage72

Electric adjustment of front seats

Applies to vehicles: with electric seat adjustment

Seat adjuster controls

The arrangement of the switches corresponds with the

design of the seats.

The adjustment switches for the seat and backrest correspond with

the design of the seat. The seats can be adjusted simply by pressing

the corresponding switch in the required direction.

Adjuster controls

Lumbar support

Seat adjuster

Height adjuster for backrest and head restraint

Thigh support*

Applies to vehicles: with electric seat adjustment

Seat adjustment

You can use the electrical adjustment to set the position,

angle and shape of the seat so that you can travel in a

safe and comfortable sitting position.

Before adjusting your seat, please read and observe the

warnings ⇒ .

Adjusting contour of lumbar support

– Press the front or rear of switch to increase or

decrease the curvature of the lumbar support as

required.

Adjusting height of lumbar support

– Press the top or bottom of adjuster switch to move the

lumbar support upwards or downwards as required.

Moving seat backwards or forwards

– Press switch ⇒ fig. 74 forwards or backwards.

Adjusting seat height

– Press switch up or down.

Raising/lowering seat at front

– Press the front of switch up or down.

Raising/lowering seat at rear

– Press the rear of switch up or down.

Adjusting backrest angle

– Press switch forwards or backwards.

Fig. 74 Front seat:

Adjuster controls

document_0900452a8179700c.book Seite 72 Donnerstag, 22. März 2007 10:19 10

Seats and storage 73

Controls Safety Driving tips General maintenance Self-help Technical data

Adjusting head restraint height

– Press switch up or down.

Extending or shortening the thigh support*

– Lift the control below the seat cushion. The front seat

cushion will spring forward.

– Slide the seat cushion back to the desired position.

WARNING

• Never adjust the driver's seat when the vehicle is moving - this

could lead to an accident.

• The electrical seat adjustment also works when the ignition is

off and when the key is not in the ignition. To avoid accidental inju-

ries, never leave children unattended in the vehicle.

• Be careful when adjusting the seat height. Careless or uncon-

trolled use of the height adjustment can cause injuries.

• Do not drive with the backrests of the front seats reclined too

far as otherwise the seat belt and airbag could fail to restrain the

wearer properly in an accident, possibly leading to injury.

Applies to vehicles: with electric seat adjustment

Easy-entry function

The easy-entry function gives improved access to the rear

seats.

Tipping the front backrests forward

– Pull up the lever ⇒ fig. 75.

– Tip the backrest forward and down.

Moving the front seats forward

– Press and hold the switch until the seat reaches the

desired position.

Moving the front seats back

– Press and hold the switch until the seat reaches the

desired position. The seat will stop automatically when it

has moved back to its original position.

The front backrests can be tipped forward for easier access to the

rear seats (the head restraints will be retracted automatically). At

the same time, the front seats can also be moved forwards and

backwards as required.

Fig. 75 Driver's seat:

easy-entry controls

document_0900452a8179700c.book Seite 73 Donnerstag, 22. März 2007 10:19 10

Seats and storage74

When the front seats are moved forward, their original positions are

stored in a memory. The seats then stop automatically in this posi-

tion when they are moved back. If you want to move one of the seats

back further, release the switch and press it again.

The head restraints on the front seats retract automatically

(depending on the seat height setting) when the backrests are

tipped forward, and move back to their original positions when the

backrests are returned to the upright position.

Note

The easy-entry switches on the relevant seat are out of action when

the driver's or passenger's doors are closed.

Seat memory

Applies to vehicles: with seat memory

Memory for driver's seat

You can use the recall buttons in the driver's door to store

and recall the seat adjustments for two drivers.

As well as the driver's seat position, the seat memory will store and

recall the exterior mirror settings (if the vehicle is equipped accord-

ingly):

Storing and recalling settings

You can store and recall the settings for two different drivers using

the recall buttons 1 and 2 ⇒ fig. 76 ⇒ page 74.

In addition, the current settings are automatically stored when you

lock the vehicle and assigned to the remote control key that is being

used. When you unlock the vehicle, the system automatically recalls

the settings stored on that remote control key.

Switching seat memory on and off

The seat memory will be out of action if the switch is in the

raised position (press and release). The word OFF will then light up

in the switch.

The stored settings will all remain in the memory. We recommend

using the switch to deactivate the seat memory when the

vehicle is being driven temporarily by a different driver whose

settings do not need to be stored in the system.

Applies to vehicles: with seat memory

Storing and recalling settings

The switch must be in its down position (pressed

in) before you can store and recall the desired settings.

Storing settings

– Adjust the driver's seat as required.

– Adjust both exterior mirrors.

– Press and hold the button. At the same time press

one of the recall buttons for at least a second.

– Then release the buttons. The settings are now stored on

the selected recall button.

Fig. 76 Driver's door:

Seat memory

ON/OFF

SET

document_0900452a8179700c.book Seite 74 Donnerstag, 22. März 2007 10:19 10

Seats and storage 75

Controls Safety Driving tips General maintenance Self-help Technical data

Recalling settings

– If the driver's door is open, press the desired recall

button briefly.

– If the driver's door is closed, press and hold down the

desired recall button until the programmed settings are

reached.

A tone will sound and the diode in the button ⇒ page 74,

fig. 76 will light up to confirm that the settings have been stored.

When you lock the vehicle the current settings are automatically

stored and assigned to the remote control key. However, the

settings assigned to the remote control key will not overwrite the

settings stored on recall buttons 1 and 2. The settings stored on the

recall buttons can be called up at any time. When you unlock the

vehicle, the settings assigned to the remote control key are recalled

automatically.

If your vehicle is also driven by other persons using your remote

control key, it is advisable to store your personal settings on one of

the recall buttons. You can then recall your own settings at any time

simply by pressing the corresponding recall button. When you lock

the vehicle these settings are then stored automatically and

assigned once again to the remote control key.

WARNING

• For safety reasons, never recall seat settings when the vehicle

is moving - this could lead to an accident.

• In an emergency the recall function can be stopped at any time

by pressing the switch, or by briefly pressing any of the

recall buttons.

Applies to vehicles: with seat memory

Activating memory for remote control key

The relevant function must be activated on the sound

system or MMI so that the settings stored in the memory

can be recalled using the remote control key.

– Select: Function selector button > Seat adjustment

> Driver's seat > Remote control key > on.

SET

ON/OFF

Fig. 77 MMI display:

Driver's seat

CAR

document_0900452a8179700c.book Seite 75 Donnerstag, 22. März 2007 10:19 10

Seats and storage76

Head restraints

Adjusting the front head restraints

In combination with properly worn seat belts, the head

restraints offer effective protection. However, they must

always be properly adjusted to suit the height of the occu-

pant.

Raising head restraint

– Take hold of the sides of the head restraint with both

hands.

– Push the head restraint upwards.

Lowering head restraint

– Take hold of the sides of the head restraint.

– Press button ⇒ fig. 78 and push the head restraint

downwards.

Electric height adjustment*

– Press the switch ⇒ fig. 79 up or down to move the head

restraint to the desired height.

– You should adjust the head restraint so that the top of

the head restraint is at least at eye level, or higher

⇒ fig. 78.

For best protection, the top of the head restraint should be at least

at eye level, or higher.

The height of the head restraints is adjustable. They should be set

to suit the height of the occupant. In combination with the seat

belts, the head restraints offer effective protection, provided they

are properly adjusted.

Adjusting the rear head restraints

Fig. 78 Front seat:

Adjusting head

restraint

Fig. 79 Front seat:

Adjusting head

restraint (electric

adjustment*)

Fig. 80 Rear seats:

Head restraint

document_0900452a8179700c.book Seite 76 Donnerstag, 22. März 2007 10:19 10

Seats and storage 77

Controls Safety Driving tips General maintenance Self-help Technical data

Raising head restraint

– Take hold of the sides of the head restraint with both

hands.

– Push the head restraint upwards as far as it will go.

Lowering head restraint

– Take hold of the sides of the head restraint.

– Press the button ⇒ page 76, fig. 80 and push the head

restraint downwards.

For best protection, the top of the head restraint should be at least

at eye level, or higher.

When the rear seats are not occupied the head restraints should be

moved to the lowest position so that they do not obstruct the

driver's field of vision.

Applies to vehicles: with front armrest

Front armrest

The armrest can be adjusted to several positions and

moved back and forwards.

Adjusting armrest

– To adjust the position of the armrest, pull the armrest all

the way down.

– Then lift the armrest gradually until it engages in the

desired position.

Moving armrest

– You can move the armrest backwards or forwards

⇒ fig. 81.

Please note that the armrest can restrict the driver's movements

when it is lowered. The armrest should therefore be moved back

before driving in city traffic.

There is a storage compartment underneath the armrest.

Luggage compartment

Loading the luggage compartment

Loads in the luggage compartment should be safely

secured.

Fig. 81 Armrest

between driver's seat

and front passenger's

seat

Fig. 82 Heavy items

should be placed as far

forwards as possible.

document_0900452a8179700c.book Seite 77 Donnerstag, 22. März 2007 10:19 10

Seats and storage78

To maintain safe handling on the road, please observe the

following points:

– Distribute the weight as evenly as possible.

– Position heavy items as far forward as possible

⇒ page 77, fig. 82.

– Secure the load with the luggage net* or with non-elastic

straps secured to the fastening rings* ⇒ page 78.

WARNING

• Unsecured objects in the luggage compartment can suddenly

shift and cause changes in the handling of the vehicle.

• In an accident or a sudden manoeuvre, loose objects in the

passenger compartment can be flung forward and possibly injure

vehicle occupants.

• Always store objects in the luggage compartment and secure

with suitable straps. This is especially important for heavy

objects.

• When you transport heavy objects, always keep in mind that a

change of the centre of gravity can also cause changes in vehicle

handling.

• Please observe the important safety warnings ⇒ page 162,

“Safe driving”.

Note

Adjust the tyre pressure to match the vehicle loading - the correct

pressures are specified on the sticker on the end face of the driver's

door.

Applies to vehicles: with fastening rings

Fastening rings

There are four fastening rings in the luggage compart-

ment which can be used to secure loads.

– Use the fastening rings to secure the load ⇒ fig. 83

-arrows-.

– Please refer to the safety notes ⇒ page 169.

Fig. 83 Location of

fastening rings in

luggage compartment

document_0900452a8179700c.book Seite 78 Donnerstag, 22. März 2007 10:19 10

Seats and storage 79

Controls Safety Driving tips General maintenance Self-help Technical data

Applies to vehicles: with stretch net

Stretch net / retaining net

The stretch net / retaining net can be used to secure light

items in the luggage compartment.

Stretch net

– First secure the front hooks in the fastening rings

⇒ fig. 84.

–Then secure the rear hooks in the fastening rings.

Retaining net

– Secure the hooks of the retaining net to the fastening

rings at the bottom of the tail panel ⇒ fig. 85.

– Pull down the retaining hooks at the top of the luggage

compartment. Pull up the net and attach the loops of the

net to the retaining hooks.

You can also use the retaining hooks ⇒ fig. 85 to secure light items

of luggage, such as shopping bags, etc.

The hooks will fold up again by themselves when not in use.

WARNING

The retaining net should only be used to hold objects weighing up

to 5 kg. Heavier objects cannot be safely secured (injury risk).

Side storage compartment

The DVD player for the navigation system* is located in

the left side compartment in the luggage compartment.

Fig. 84 Stretch net laid

out

Fig. 85 Stretch net

attached in position as

retaining net

Fig. 86 Luggage

compartment: Side

trim with closed

storage compartment

document_0900452a8179700c.book Seite 79 Donnerstag, 22. März 2007 10:19 10

Seats and storage80

– To open the storage compartment, pull the handle

⇒ page 79, fig. 86.

DVD player for navigation system*

The DVD player for the navigation system is located in this storage

compartment ⇒ fig. 87 in the luggage compartment. For more

information, please refer to the Infotainment/MMI Operating

Manual.

Applies to vehicles: with folding backrests

Extending the luggage compartment from the

boot

The backrests can be folded forwards to increase the

storage space.

Releasing and folding down backrest

– When you pull the release lever ⇒ fig. 88 in the direction

of the arrow, the safety knob ⇒ fig. 89 will pop up and

the red marking on the knob will become visible.

– Fold down the backrest.

Fig. 87 Luggage

compartment: DVD

player for navigation

system

Fig. 88 Release lever in

luggage compartment

Fig. 89 Safety knob

document_0900452a8179700c.book Seite 80 Donnerstag, 22. März 2007 10:19 10

Seats and storage 81

Controls Safety Driving tips General maintenance Self-help Technical data

Returning backrest to an upright position

– Push the backrest up again until it engages securely

⇒ . The red marking on the safety knob ⇒ page 80,

fig. 89 should no longer be visible when the backrest is

properly secured.

When the backrest is properly engaged in its upright position, it can

be locked and unlocked with the key. This prevents unauthorised

access to the luggage compartment from inside the vehicle.

The luggage compartment can only be extended from the boot

when the backrest has not been locked with the key.

WARNING

The rear backrest must always be securely latched so that objects

stored in the luggage compartment will not fly forward during

sudden braking.

Caution

When returning the backrest to an upright position, make sure that

the seat belts for the rear seats are in their guides so that they

cannot be caught up and damaged in the catches for the backrest.

It is also important to remove any other objects from the rear seats

to avoid damaging the backrest when folding it forwards.

Applies to vehicles: with folding backrests

Extending the luggage compartment from

inside the vehicle

The backrests can be folded forwards to increase the

storage space.

Folding down backrest

– When you pull the release handle ⇒ fig. 90 in the

direction of the arrow, the safety knob will pop up and

the red marking on the knob will become visible.

– Fold down the backrest.

Returning backrest to an upright position

– Push the backrest up until it engages securely ⇒ . The

red marking on the safety knob should no longer be

visible when the backrest is properly secured.

When the backrest is properly engaged in its upright position, the

release handle can be locked and unlocked with the key. This

prevents unauthorised access to the luggage compartment from

inside the vehicle.

Fig. 90 Release handle

on backrest

document_0900452a8179700c.book Seite 81 Donnerstag, 22. März 2007 10:19 10

Seats and storage82

WARNING

The rear backrest must always be securely latched so that objects

stored in the luggage compartment will not fly forward during

sudden braking.

Caution

When returning the backrest to an upright position, make sure that

the seat belts for the rear seats are in their guides so that they

cannot be caught up and damaged in the catches for the backrest.

Applies to vehicles: with folding backrests

Locking the backrest

–Turn the key ⇒ fig. 91 to the right to lock the backrest.

– Turn the key to the left to unlock the backrest.

When the backrest is properly engaged in its upright position, the

release handle can be locked and unlocked with the key. This

prevents unauthorised access to the luggage compartment from

inside the vehicle.

Caution

When returning the backrest to an upright position, make sure that

the seat belts for the rear seats are in their guides so that they

cannot be caught up and damaged in the catches for the backrest.

Storage shelf

The storage shelf behind the rear backrest should only be

used to store light articles of clothing.

WARNING

Do not store any heavy or hard objects on the storage shelf. They

could cause injury if the brakes are applied suddenly.

Caution

Please note that hard objects could chafe against the wires of the

heating element in the rear window and cause damage.

Note

Make sure that the slots between the rear window and the storage

shelf are kept clear to ensure unimpaired ventilation.

Fig. 91 Locking the

backrest

document_0900452a8179700c.book Seite 82 Donnerstag, 22. März 2007 10:19 10

Seats and storage 83

Controls Safety Driving tips General maintenance Self-help Technical data

Applies to vehicles: with load-through hatch

Load-through hatch

You can use the load-through hatch and bag to transport

objects safely inside the vehicle.

Opening the load-through hatch

– In the passenger compartment, pull down the centre rear

armrest.

– Pull the release catch ⇒ fig. 92 -arrow- and fold the cover

of the load-through hatch down into the passenger

compartment.

– Open the boot lid.

– Working from the luggage compartment, push the bag

through the opening.

– Secure the bag ⇒ page 83.

Closing the load-through hatch

– Open the boot lid.

– Take the bag out of the load-through hatch.

– Fold the cover of the load-through hatch back up from

inside the vehicle until it engages.

– Fold up the centre armrest again if desired.

– Close the boot lid.

WARNING

Loose objects must be transported in the bag, as the bag can be

secured. Individual objects cannot be secured - Risk of accident!

Note

• You can also open the load-through hatch from the luggage

compartment. Press down the release catch and push the cover

forwards.

• The load-through hatch can be locked and unlocked from inside

the vehicle using the emergency key ⇒ fig. 92.

Applies to vehicles: with load-through hatch

Securing the transport bag

The transport bag must be secured in the luggage

compartment.

Fig. 92 In the rear seat:

Opening the lid of the

load-through hatch

Fig. 93 Luggage

compartment:

Securing the bag

document_0900452a8179700c.book Seite 83 Donnerstag, 22. März 2007 10:19 10

Seats and storage84

Securing the bag in the luggage compartment

– Two belts with hooks are attached to the bottom side of

the bag. Engage the hooks into the rear fastening rings

in the luggage compartment ⇒ page 83, fig. 93.

Securing the objects in the bag

– Pull the free end of the belt tight to secure it ⇒ fig. 94.

Note

If the bag is damp or wet, allow it to dry before putting it away.

Roof carrier

Description

Additional loads can be transported using the roof carrier.

Note the following points if you intend to carry loads on the roof:

• The rain channels are moulded into the roof as part of the aero-

dynamic roof design. It is therefore not possible to mount conven-

tional roof luggage racks. We recommend using the carrier units

from the range of Audi Genuine accessories.

• These carrier units form the basic elements of a complete roof

carrier system. Special fixtures must then be added in order to

safely transport luggage, bicycles, skis, surf boards or boats on the

roof. All the elements of this system are available from Audi dealers.

Caution

Any damage to the vehicle caused by the use of other types of roof

rack or incorrect installation will not be covered by the factory

warranty. The roof carrier system must therefore be installed exactly

according to the instructions provided.

Attachment points

The roof carrier must be attached at the marked points

only.

Mounting

The front feet of the carrier units must be fitted exactly onto the

locating pins between the side frame and the roof frame trim

⇒ fig. 95. The pins come into view when you push the sealing lip

back off the roof frame trim using the tool supplied with the roof

carrier. The rear attachment points are marked by two small

arrows on the top edge of the side window.

Fig. 94 Securing the

objects in the bag

Fig. 95 Attachment

points for carrier units

document_0900452a8179700c.book Seite 84 Donnerstag, 22. März 2007 10:19 10

Seats and storage 85

Controls Safety Driving tips General maintenance Self-help Technical data

Roof load

Loads carried on the roof must be securely attached. The

car's handling is affected when transporting loads.

The maximum permissible roof load for your vehicle is 75 kg. The

load limit applies to the combined weight of the carrier system and

the load itself.

It will not be possible to carry the full maximum load if the roof

carrier you are using is rated for a load which is less than this figure.

Do not exceed the maximum weight limit for the roof carrier, which

is listed in the fitting instructions.

WARNING

• To prevent accidents, loads carried on the roof must be

securely attached.

• Do not exceed the maximum roof load for the vehicle, the

maximum axle loads or the maximum gross vehicle weight, as this

could cause an accident.

• When transporting heavy or bulky loads on the roof, bear in

mind that the car's handling is affected by the extra weight on the

roof and a possible susceptibility to cross winds. Adjust your

speed and driving style accordingly to avoid accidents.

For the sake of the environment

The increased air resistance when the roof carrier is fitted means

that the vehicle uses more fuel. For this reason you should always

take off the roof carrier when it is not in use.

Cup holders

Front cup holder

– Two drinks can be placed in this cup holder ⇒ fig. 96.

Opening rear cup holder

– Press the symbol

 ⇒ fig. 97.

Placing drinks in rear cup holder

– To adjust the arm of the cup holder , move it in the

direction indicated by the arrow.

Fig. 96 Centre console:

Front cup holder

Fig. 97 Cup holder in

rear armrest

document_0900452a8179700c.book Seite 85 Donnerstag, 22. März 2007 10:19 10

Seats and storage86

– Position the cup in the holder and let go of the arm. The

arm will move back automatically to secure the cup.

Closing cup holder

– Press the middle piece between the two arms and push

the cup holder back into the shaft as far as it will go.

The retainer arm should be positioned against the drinks container

so that it is held securely.

One or two drink containers can be held in the centre armrest.

WARNING

• Do not put any hot drinks in the cup holders while the vehicle

is moving. You could be scalded if the hot liquid is spilt.

• Do not use hard china cups or glasses. These could cause injury

in the event of an accident.

Caution

You should avoid putting open drinks containers in the cup holders.

The drinks could otherwise spill over and cause damage to e.g. the

electrical equipment or the seat covers.

Ashtrays

Front ashtray

Opening ashtray

– Slide the cover open.

Closing ashtray

– Lightly press the cover to make the ashtray close auto-

matically.

Removing ashtray

–Slide the switch ⇒ fig. 98 to the right to release the

ashtray.

– Take out the ashtray ⇒ fig. 98.

Inserting ashtray

– Insert the ashtray and press it into its mountings.

WARNING

Never put waste paper in the ashtray, as this could cause a fire.

Fig. 98 Centre console:

Ashtray open

document_0900452a8179700c.book Seite 86 Donnerstag, 22. März 2007 10:19 10

Seats and storage 87

Controls Safety Driving tips General maintenance Self-help Technical data

Rear ashtray

Opening ashtray

– Pull the front lip of the ashtray ⇒ fig. 99 in the direc-

tion of the arrow.

Removing ashtray

– Press down the retainer and take out the ashtray.

Inserting ashtray

– Place the ashtray in the holder.

WARNING

Never put waste paper in the ashtray, as this could cause a fire.

Cigarette lighter and electrical

sockets

Cigarette lighter

The 12 Volt socket for the cigarette lighter can also be

used as a power source for other electrical appliances.

Using cigarette lighter

– Open the cover of the front ashtray.

– Press in the cigarette lighter knob.

– Wait for the lighter to spring out.

– Pull out the cigarette lighter immediately.

– Use the glowing heater element of the cigarette lighter to

light your cigarette.

– Put the cigarette lighter back in its socket.

Operating electrical socket

– Take out the cigarette lighter.

– Insert the plug of the electrical appliance into the ciga-

rette lighter socket.

Fig. 99 Rear centre

console: Ashtray

Fig. 100 Front ashtray

(open)

document_0900452a8179700c.book Seite 87 Donnerstag, 22. März 2007 10:19 10

Seats and storage88

The cigarette lighter employs a standard 12 Volt socket which can

also be used as a power source for electrical appliances. The appli-

ances connected to the socket must not exceed a power rating of

100 W.

WARNING

• Take care when using the cigarette lighter. Carelessness or

negligence when using the cigarette lighter can cause burns.

• The cigarette lighter also works when the ignition is off and

when the ignition key is removed. To avoid the risk of fire, never

leave children unsupervised in the vehicle.

• The electrical sockets and any appliances connected to them

will operate only when the ignition is switched on. Improper use

of the electrical sockets or the appliances connected to them can

cause injuries or fire. To avoid the risk of injury, never leave chil-

dren unsupervised in the vehicle with the key.

Caution

Always use the correct type of plugs to avoid damaging the sockets.

Note

Using electrical appliances with the engine switched off will drain

the battery.

Applies to vehicles: with 12 Volt sockets

12 Volt sockets

Electrical equipment can be connected to both 12 Volt

sockets.

Electrical socket in luggage compartment and

front centre console

– Open the cover cap concealing the socket ⇒ fig. 101.

– Insert the plug of the electrical appliance into the socket.

Electrical socket in rear centre console

– Fold up the lid ⇒ page 89, fig. 103 to access the socket.

Fig. 101 Detail of the

side trim in the

luggage compartment:

12 Volt socket

Fig. 102 Electrical

socket in the centre

console

document_0900452a8179700c.book Seite 88 Donnerstag, 22. März 2007 10:19 10

Seats and storage 89

Controls Safety Driving tips General maintenance Self-help Technical data

– Insert the plug of the electrical appliance into the socket.

Electrical equipment can be connected to the 12 Volt socket. The

appliances connected to the socket must not exceed a power rating

of 100 W.

WARNING

The electrical sockets and any appliances connected to them will

operate only when the ignition is switched on. Improper use of the

electrical sockets or the appliances connected to them can cause

injuries or fire. To avoid the risk of injury, never leave children

unsupervised in the vehicle with the key.

Caution

• To avoid damage to the vehicle's electrical system, never

connect equipment that generates electrical current, such as a solar

panel or battery charger, to the 12 Volt sockets or cigarette lighter in

order to charge the vehicle's battery.

• Use only equipment which has been tested for electromagnetic

compatibility in compliance with EC Directive 2004/104/EC.

Note

Using electrical appliances with the engine switched off will drain

the battery.

Applies to vehicles: with 230 Volt Euro socket

On-board 230 Volt Euro socket

Electrical equipment can be connected to the 230 Volt

Euro socket in the rear centre console.

The 230 Volt Euro socket can only be used when the engine

is running ⇒ .

– Fold up the lid to access the socket.

– Plug the Euro connector into the socket. This will auto-

matically release the child safety device.

LED in electrical socket

Appliances suitable for connection

Electrical equipment with a Euro plug connector can be connected

to the 230 Volt Euro socket. The appliances connected to the

230 Volt Euro socket must not exceed a power rating of 150 W

(300 W peak power).

Steady green light: The socket is ready for use.

Flashing red light: The socket has tripped out due

to a power surge, overheating or

similar

Fig. 103 Rear centre

console: 230 Volt Euro

socket

document_0900452a8179700c.book Seite 89 Donnerstag, 22. März 2007 10:19 10

Seats and storage90

If you connect more than one appliance, the total power rating of all

appliances must not exceed 150 W. If necessary, check the type

plates on the connected appliances for details of the power ratings.

Connected appliances must be in perfect condition and free of

defects.

WARNING

• Heavy appliances or plugs (such as power supply units) can

damage the mounting of the 230 Volt Euro socket if they are

suspended directly from the socket – Risk of injury!

• Make sure that all connected appliances are securely stowed

when driving to prevent them from being catapulted through the

car under braking or in an accident – Danger to life!

• Never spill liquid over the socket – Danger to life! If the socket

does get wet, ensure that it is absolutely dry before using it again.

• Improper use of the electrical socket or appliances connected

to it can cause injuries or fire – Risk of injury!

• Never leave children unattended in the vehicle while the engine

is running – Risk of injury!

• Connected appliances behave differently than when they are

connected to the public electricity grid. As a result, the connected

appliances may become hot during operation – Risk of injury!

• When using adapters or extension cables, please remember

that the child safety device on the 230 Volt Euro socket is deacti-

vated and the socket is live – Risk of injury!

• Do not insert conductive materials, such as knitting needles,

into the contacts of the 230 Volt Euro socket – Danger to life!

• Switch off the connected electrical appliances if the inverter

trips out due to overheating – Risk of injury!

Caution

• Please observe the operating instructions for the connected

appliances.

• If the power drawn by the connected appliances is above 150 W,

the inverter in the socket will get warm. The inverter will trip out if

the temperature exceeds a certain limit. The inverter can trip out on

hot days even when an appliance with a suitable power rating is

used. The inverter will switch on again automatically after it has

cooled down. Appliances which are already connected and

switched on will be activated again automatically ⇒ .

• Do not connect lamps which contain a neon tube. For technical

reasons, this may damage the lamp.

• Do not connect 115 Volt appliances to the 230 Volt Euro socket.

This may cause irreparable damage to the appliance. Check the type

plate on the appliance if you are unsure of the voltage rating.

• With some power supplies (e.g. on laptop computers), the inte-

grated surge suppressor prevents the equipment from being

switched on because the starting current is too high. If this

happens, please disconnect the power supply unit from the load

and wait for about 10 seconds before re-connecting.

Note

• Unshielded equipment can cause interference on the radio, TV

and vehicle's electrical system.

• The Euro socket has an integrated child safety device. There is no

power at the socket until the Euro connector is fully inserted.

• Some appliances may not function normally due to the lower

power rating (wattage).

• The socket can be operated with 115 Volt power supplies, as is

the case in certain countries. In this case, a different type of inverter

must be installed in the vehicle. Retrofit kits are available from your

Audi dealer. Do not connect 115 Volt appliances to the 230 Volt Euro

socket.

• Interference can occur on the radio's AM waveband if electrical

appliances are used near the rear window aerial.

document_0900452a8179700c.book Seite 90 Donnerstag, 22. März 2007 10:19 10

Seats and storage 91

Controls Safety Driving tips General maintenance Self-help Technical data

Storage compartments

Overview

There are several storage compartments at various points

in the vehicle.

Glove box

The glove box is equipped with a lock* and a light.

Opening glove box

– Pull the catch on the lid in the direction indicated (arrow)

⇒ fig. 104 and open the lid.

Closing glove box

– Close the lid and push it in until it engages.

The glove box lid has separate holders for a pen and a note pad.

On the right-hand side of the glove box there is a holder with a key

shell. In order to start the engine with the spare key, it has to be

clipped into this shell.

WARNING

To avoid the risk of injuries, always keep the glove box lid closed

when driving.

Compartment for (sun)glasses in headliner

– To open the cover, lightly press the panel ⇒ fig. 105

(arrow). The cover will then open by itself.

– To close the cover, push it upwards until it engages.

Glove box ⇒ page 91

Compartment for (sun)glasses in head-

liner

⇒ page 91

Storage compartments in the front seats ⇒ page 92

Coat hooks ⇒ page 92

First-aid kit ⇒ page 254

Side storage compartment in luggage

compartment

⇒ page 79

Warning triangle ⇒ page 254

Fig. 104 Glove box

Fig. 105 Compartment

for (sun)glasses in

headliner

document_0900452a8179700c.book Seite 91 Donnerstag, 22. März 2007 10:19 10

Seats and storage92

WARNING

Always keep the compartment cover closed while the vehicle is in

motion to reduce the risk of injury during a sudden braking

manoeuvre or in the event of an accident.

Coat hooks

The coat hooks are located on the rear side of the B-pillars

(in the rear passenger compartment).

WARNING

• Please make sure that any items of clothing hanging from the

coat hooks do not obstruct your view to the rear.

• Only use the coat hooks for light items of clothing and make

sure that there are no heavy or sharp objects in the pockets.

• Do not use clothes hangers to hang up the clothing, as this

could interfere with the function of the head-protection

airbags*.

Applies to vehicles: with storage compartments in the front seats

Storage compartments in front seats

There is a fold-out drawer in the front part of each front

seat.

Opening

– Pull the handle to open the compartment.

Closing

– Close the lid and push it in until it engages.

Note

The storage compartment will hold a maximum weight of 1 kg.

document_0900452a8179700c.book Seite 92 Donnerstag, 22. März 2007 10:19 10

Seats and storage for Your Audi A5 4 Door First Generation (2007-2013)

Related Topics

Popular Owner Manuals

Latest Owner Manuals