2025-2026 Audi A5 4 Door Emergency assistance -> Towing User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Emergency assistance -> Towing for Your Audi A5 4 Door Third Generation (2025-2026)

Emergency assistance  
With the engines running, remove the cables in  
reverse order of the way they were installed.  
Close the cover on the positive terminal.  
cumstances. Inexperienced persons should not  
tow a vehicle.  
Notes on towing  
When the engine is stopped, the transmission  
will not be sufficiently lubricated if traveling at  
high speeds and long distances:  
WARNING  
Never connect the jump start cable directly  
to your vehicle battery. Only use the connec-  
tions in the engine compartment.  
The maximum permitted towing speed is 30  
mph (50 km/h).  
Do not touch the non-insulated parts of the  
terminal clamps. The cable must also not  
come into contact with vehicle components  
that conduct electricity when it is connected  
to the positive vehicle battery terminal. This  
can cause a short circuit.  
The maximum permitted towing distance is 30  
miles (50 km).  
Additional information on towing with a tow  
truck  
The vehicle may only be towed with the front axle  
raised. Do not wrap any chains or cables around  
the brake lines.  
The plugs on the battery cells must not be  
opened.  
Keep ignition sources (such as open flames,  
burning cigarettes, etc.) away from the vehi-  
cle batteries to reduce the risk of an explo-  
sion.  
Tow bar and towing cable  
The vehicle can be towed with a tow bar or tow-  
ing cable. Both persons involved should be famil-  
iar with the special considerations when towing,  
especially when using a towing cable.  
Route the jump start cables so they cannot  
get caught in the moving parts in the other  
vehicle's engine compartment.  
Always make sure the traction force does not ex-  
ceed the permitted level and there are no shock  
loading conditions. There is always the risk of the  
coupling becoming overloaded when driving off-  
road.  
Note  
Please note that the connecting process previ-  
ously described for the jump start cables is in-  
tended for when your vehicle is being jump  
started.  
For the most safety and security, drive with a tow  
bar. You should use a towing cable only if a tow  
bar is not available. Use a towing cable made of  
synthetic elastic cable or a cable made of similar  
elastic material.  
Tips  
Make sure that the connected jump start ca-  
bles have sufficient contact with metal.  
WARNING  
Towing  
Towing highly increases the risk of an acci-  
dent, for example from colliding with the  
towing vehicle.  
General information  
You should only perform the following steps if  
you have the necessary technical knowledge and  
tools.  
To reduce the risk of an accident, do not al-  
low anyone to remain inside the vehicle  
when it is being transported by a tow truck  
or a special transporter.  
Towing requires a certain amount of practice.  
Audi recommends contacting a towing company  
to have the vehicle transported.  
Never secure the tow bar or towing cable to  
parts of the vehicle’s axles or suspension.  
These could be damaged, resulting in acci-  
dents and serious injuries.  
You should only have your vehicle towed by an-  
other vehicle when disabled in exceptional cir-  
293  
Emergency assistance  
Vehicle being towed (rear)  
Note  
Make sure the ignition is turned on so that the  
If normal towing methods are not possible,  
for example if the transmission is faulty or if  
the towing distance is greater than 30 miles  
(50 km), then transport the vehicle on a  
special carrier.  
steering wheel is not locked and so that you can  
use the turn signals, the horn, and the wind-  
shield wipers if needed ð  
.
The full functionality of the brake booster and  
power steering may not be available. You would  
then need to use more force to steer and brake  
the vehicle.  
If the vehicle is towed by a tow truck at the  
axle that is not permitted, this can cause se-  
vere damage to the transmission.  
Release the parking brake ðpage 108.  
Select the “N” position.  
Make sure the towing cable is always taut.  
The vehicle must not be tow started for  
technical reasons.  
Tips  
WARNING  
If the power supply is interrupted, then it  
will not be possible to move the selector out  
of the "P" position. The parking lock must  
be released using the manual release before  
towing the vehicle ðpage 102.  
Never tow a vehicle using a tow bar or tow-  
ing cable if the vehicle does not have electri-  
cal power.  
If the vehicle loses power while it is being  
towed, stop towing the vehicle immediately  
and consult an authorized Audi dealer or  
qualified repair facility.  
Turn off Audi pre sense* ðpage 159 when  
loading the vehicle onto a vehicle carrier,  
train, ship, or other type of transportation,  
or when towing the vehicle. This can prevent  
an undesired intervention from the pre  
sense* system.  
Rear towing eye  
Follow the local legal regulations for tow-  
ing.  
Towing  
Read and follow the important information on  
ðpage 293.  
Preparations  
Fig. 184 Rear bumper: installing the towing eye  
Only secure the towing cable or tow bar at the  
designated towing eye ðpage 294.  
Make sure the towing cable is not twisted. Oth-  
erwise it could disconnect from the towing eye  
while towing.  
Turn on the emergency flashers in both vehicles  
ðpage 57. However, do not do this if it prohib-  
ited by law.  
Towing vehicle (front)  
Start driving only once the towing cable is taut.  
Press the brake pedal very carefully.  
Applies to: RS models  
Fig. 185 Rear bumper: installing the towing eye  
Avoid sudden braking or driving maneuvers.  
The threaded opening for the towing eye is locat-  
ed on the right rear of the bumper.  
294  
Emergency assistance  
Remove the towing eye from the vehicle tool kit  
ðpage 285.  
Press the cap inward with brief, strong pressure  
ðfig. 184 or ðfig. 185. The cap will loosen  
from the bumper.  
Tighten the towing eye as far as it will go into  
the mount. Use a suitable object to tighten the  
towing eye completely and securely in the  
mount.  
After using, place the towing eye back in the ve-  
hicle tool kit.  
WARNING  
If the towing eye is not tightened all the way  
when installing, the threads may be pulled  
out when towing the vehicle and result in an  
accident.  
Tips  
Depending on the model, the shape of the cap  
can vary.  
295  

Related Topics

Popular Owner Manuals