Get Lights and vision -> Clear vision Guide for Audi RS6 4 Door Fourth Generation (2019-2025)

Lights and vision

The vehicle stores the user’s last settings. When

you select reverse gear, an LED next to the sym-

bol for the mirror on the control panel will flash

to indicate that the automatic lowering function

is activated.

Adjusting the display brightness

You can adjust the brightness of the instrument

cluster and the displays in the Car menu

ðpage 26.

The mirror returns to its original position:

Clear vision

– If you switch the vehicle off.

Adjusting the exterior mirrors

– If you drive forwards faster than 15 km/h.

– If you switch the automatic lowering function

off by pressing the button again.

WARNING

Convex or wide-angle exterior mirrors give a

larger field of vision. However, they make ob-

jects look smaller and further away than they

really are. If you use these mirrors to estimate

the distance to vehicles behind you when

changing lane, you could misjudge the dis-

tance. Risk of accident!

Fig. 23 Driver's door: Control panel for exterior mirrors

The buttons for adjusting the exterior mirrors are

on the control panel in the driver's door.

CAUTION

/ – To select the exterior mirror (left or right

side). To adjust the mirror, press on the control

panel 1 in the desired direction.

– Applies to vehicles with electrically retracta-

ble exterior mirrors: If one of the mirror

housings is knocked out of position (e.g.

when parking), the mirrors must be fully re-

tracted with the electric control. You will

hear a loud noise when the mirrors snap

back into place. Do not readjust the mirror

housing by hand, as this will interfere with

the mirror adjuster function.

 – To fold in the exterior mirrors. To fold the

mirrors back out, press  again. One of the cen-

tre display settings allows you to control whether

or not the mirrors are folded in automatically

when you lock the vehicle.

 – To select the automatic lowering function.

– Applies to vehicles without electrically re-

tractable exterior mirrors: If one of the mir-

ror housings is knocked out of position (e.g.

when parking), it must be returned to its

proper position by hand.

If the electrical adjustment should fail to oper-

ate, both of the mirrors can be adjusted by hand

by lightly pressing the edge of the mirror glass.

Automatic lowering function

– Before washing the vehicle in an automatic

car wash, please make sure to retract the

exterior mirrors to prevent them from being

damaged. Do not fold electrically retracta-

ble exterior mirrors in or out by hand! Al-

ways use the electrical power control.

Select this function to obtain a better view of the

kerb, such as when reversing into a parking

space. The automatic lowering function can only

be activated when the vehicle is in reverse gear.

►

Press  to activate the automatic lowering

function.

Anti-dazzle setting

►

Select the left and/or right exterior mirror.

►

Adjust the mirror position using the control

Manual anti-dazzle interior mirror

panel if necessary.

►

Pull the lever at the bottom of the mirror to-

wards you.



Lights and vision

Automatic anti-dazzle mirrors

At low ambient temperatures, particularly below

freezing, the switching processes are delayed.

►

The interior and exterior mirrors will darken

when bright light (e.g. from the headlights of a

following vehicle) shines on the surface of the

interior mirror.

Setting the transparency

You can set the transparency of the individual

segments by pushing the  switch 1 .

The automatic anti-dazzle mirrors may not func-

tion as intended if the light falling on the surface

of the interior mirror is obstructed.

►

Automatic adjustment: Briefly push the switch

to the corresponding end position to change all

segments at once to either all let sunlight in or

all block it out. You can stop the automatic ad-

justment at any position by pressing the switch

again.

The automatic anti-dazzle mirrors do not darken

if the interior lighting is on or the car is in reverse

gear.

►

Manual adjustment: Push the switch to the cor-

WARNING

responding end position and hold it there until

the segments let sunlight in or block it out as

desired. You can stop the manual adjustment at

any position by letting go of the switch.

Electrolyte fluid can leak from a broken auto-

matic anti-dazzle mirror. This fluid can cause

irritation to the skin, eyes, and respiratory or-

gans. Wash thoroughly with clean water

should you come into contact with this fluid.

Seek medical assistance if necessary.

Selecting a defined transparency pattern

You can select one of the defined transparency

patterns by pressing the  switch 1 .

CAUTION

►

Press the switch to select a transparency pat-

tern or to change between the transparency

patterns.

Electrolyte fluid can leak from a broken auto-

matic anti-dazzle mirror. This fluid can dam-

age plastic surfaces and paintwork. Use a wet

sponge or similar to remove the fluid as soon

as possible.

Information on the sun visors

Operating the panoramic glass roof with

switchable transparency

Fig. 25 Headliner: Sun visor

Sun visors

The sun visors can be pulled out of their mount-

ings 1 and turned towards the doors.

Fig. 24 Headliner: Switch for panoramic glass roof with

switchable transparency

Make-up mirrors

The panoramic glass roof with switchable trans-

parency is divided into segments. You can adjust

the settings so that certain segments let sunlight

in or block it out. You can also select one of the

defined transparency patterns.

►

Slide the make-up mirror cover 2 to the side.

The mirror light will be switched on.

Lights and vision

be activated automatically in the rain. The higher

the sensitivity level for the rain sensor (i.e. the

further switch 6 is moved to the right), the

sooner the windscreen wipers react to moisture

on the windscreen. You can deactivate the rain

sensor mode in the Car menu ðpage 26 (this will

activate the intermittent wipe mode). In inter-

mittent wipe mode, you can adjust the interval

with switch 6 .

Using the side blinds

2 Slow wipe

3 Fast wipe

Fig. 26 Rear door: Side blind

4 Single wipe. If you hold the wiper lever in this

position, the wipers will switch from slow contin-

uous wiping to fast continuous wiping after a

while. Single wipe also works when the vehicle is

switched off.

►

Pull out the side blind on the rear door and

hook it into the retainer at the top of the door

frame.

Wipers

5 Wash/wipe . The number of wipe and extra-

wipe cycles depends on how long you hold the

wiper lever in position 5 .

Using the windscreen wipers

The windscreen is given an extra wipe a few sec-

onds later to remove any dribbles of water (if the

vehicle is moving). You can deactivate this func-

tion by moving the wiper lever to position

again within 10 seconds after the extra wipe. The

extra-wipe function is activated again the next

time you switch the vehicle on.

The headlight washer system only operates when

the dipped headlights are switched on. The head-

lights are also automatically washed intermit-

tently when you move the wiper lever to position

5 .

Fig. 27 Wiper lever: Windscreen wipers

7 Rear wipe . The frequency of the rear wiper

depends on the frequency of the windscreen wip-

ers.

If the windscreen wipers are on and in operation,

the rear window wiper will also be switched on

automatically when you engage reverse gear.

Fig. 28 Wiper lever: Rear window wiper

8 Rear wash/wipe . The number of wiper cy-

cles depends on how long you hold the wiper lev-

er in position 8 . The reversing camera is also

washed (depends on the vehicle’s equipment).

►

Move the windscreen wiper lever  to the ap-

propriate position:

0 Wipers off



1 Rain sensor/intermittent wipe. As long as the

vehicle has been moving faster than approx.

4 km/h at least once, the windscreen wipers will

Lights and vision -> Clear vision for Your Audi RS6 4 Door Fourth Generation (2019-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals