Get Lights and vision -> Interior lights Guide for Audi RS6 4 Door Fourth Generation (2019-2025)

Lights and vision

Reading lights



Automatic headlights: fault. See owner's

manual

►

Briefly touch the surface 1 to turn the appro-

priate reading light on/off.

To dim the reading light, touch the surface

when the light is switched off, and hold your

finger on the surface until the desired bright-

ness level is reached.

The light sensor/rain sensor is out of action. For

safety reasons, the dipped headlights will then

be switched on permanently when the lights are

set to AUTO. Drive to a qualified workshop soon

and have the fault rectified.

►

On some versions, the reading lights are on the

side.

Interior lights

Switching the front interior lights on/off

Background lighting settings

The background lighting turns on when the vehi-

cle is switched on. The background lighting is de-

activated when the light function is OFF.

You can change the settings for the background

lighting in the Car menu ðpage 26.

Available settings:

– You can adjust the brightness and colour of the

background lighting individually for the linear

and surface lighting.

Fig. 21 Headliner: Interior lights

Buttons for interior lights

1  – Interior lights on/off

2  – Rear interior lights on/off

– You can also select from several defined colour

settings.

– You can set the linear and surface lighting to

change according to the Audi drive select

mode.

Touch-sensitive reading lights

►

Briefly touch the surface 3 to turn the appro-

Functional background lighting settings

priate reading light on/off.

►

To dim the reading light, touch the surface

The functional background lighting uses the line-

ar and surface lighting to indicate when certain

functions are activated and to provide warnings

about hazards. For example, it can show an acti-

vated turn signal or provide a warning if one of

the doors is open. The main component of this

lighting is a light strip at the bottom edge of the

windscreen.

when the light is switched off, and hold your

finger on the surface until the desired bright-

ness level is reached.

Switching the rear interior lights on/off

You can switch the functional background light-

ing on/off for certain functions and change the

brightness in the Car menu ðpage 26.

The functional background lighting is always

switched on for certain functions.

Fig. 22 Headliner: Rear reading lights

Lights and vision

The vehicle stores the user’s last settings. When

you select reverse gear, an LED next to the sym-

bol for the mirror on the control panel will flash

to indicate that the automatic lowering function

is activated.

Adjusting the display brightness

You can adjust the brightness of the instrument

cluster and the displays in the Car menu

ðpage 26.

The mirror returns to its original position:

Clear vision

– If you switch the vehicle off.

Adjusting the exterior mirrors

– If you drive forwards faster than 15 km/h.

– If you switch the automatic lowering function

off by pressing the button again.

WARNING

Convex or wide-angle exterior mirrors give a

larger field of vision. However, they make ob-

jects look smaller and further away than they

really are. If you use these mirrors to estimate

the distance to vehicles behind you when

changing lane, you could misjudge the dis-

tance. Risk of accident!

Fig. 23 Driver's door: Control panel for exterior mirrors

The buttons for adjusting the exterior mirrors are

on the control panel in the driver's door.

CAUTION

/ – To select the exterior mirror (left or right

side). To adjust the mirror, press on the control

panel 1 in the desired direction.

– Applies to vehicles with electrically retracta-

ble exterior mirrors: If one of the mirror

housings is knocked out of position (e.g.

when parking), the mirrors must be fully re-

tracted with the electric control. You will

hear a loud noise when the mirrors snap

back into place. Do not readjust the mirror

housing by hand, as this will interfere with

the mirror adjuster function.

 – To fold in the exterior mirrors. To fold the

mirrors back out, press  again. One of the cen-

tre display settings allows you to control whether

or not the mirrors are folded in automatically

when you lock the vehicle.

 – To select the automatic lowering function.

– Applies to vehicles without electrically re-

tractable exterior mirrors: If one of the mir-

ror housings is knocked out of position (e.g.

when parking), it must be returned to its

proper position by hand.

If the electrical adjustment should fail to oper-

ate, both of the mirrors can be adjusted by hand

by lightly pressing the edge of the mirror glass.

Automatic lowering function

– Before washing the vehicle in an automatic

car wash, please make sure to retract the

exterior mirrors to prevent them from being

damaged. Do not fold electrically retracta-

ble exterior mirrors in or out by hand! Al-

ways use the electrical power control.

Select this function to obtain a better view of the

kerb, such as when reversing into a parking

space. The automatic lowering function can only

be activated when the vehicle is in reverse gear.

►

Press  to activate the automatic lowering

function.

Anti-dazzle setting

►

Select the left and/or right exterior mirror.

►

Adjust the mirror position using the control

Manual anti-dazzle interior mirror

panel if necessary.

►

Pull the lever at the bottom of the mirror to-

wards you.



Lights and vision -> Interior lights for Your Audi RS6 4 Door Fourth Generation (2019-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals