2019-2025 Audi RS6 4 Door Opening and closing -> Occupant detection User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Opening and closing -> Occupant detection for Your Audi RS6 4 Door Fourth Generation (2019-2025)

Opening and closing  
Indirect occupant detection without sensor  
When the function has been deactivated, the LED  
on the door sill will flash briefly and then remain  
off for approx. half a minute.  
The system monitors whether the rear doors are  
opened. If one of the rear doors has been  
opened, the system assumes that there could be  
someone on the rear seats ðpage 38, Driver  
messages about the occupant detection system.  
WARNING  
Do not leave anyone (especially children) in  
the car if it is locked from the outside and the  
safelock mechanism is activated: the doors  
and windows cannot then be opened from the  
inside. Locked doors could delay assistance in  
an emergency, potentially putting lives at  
risk.  
WARNING  
Never leave persons or animals unsupervised  
in the vehicle, even if the vehicle is equipped  
with an occupant detection system.  
Setting the occupant detection system  
CAUTION  
You can adjust the settings for the occupant de-  
tection system in the Car menu ðpage 26.  
If you switch off the safelock mechanism,  
the interior monitor and tow-away protec-  
tion are automatically disabled, and vice  
versa. This means that your vehicle is no  
longer completely protected against break-  
ins and theft.  
The settings depend on the equipment fitted in  
your vehicle.  
The following settings are possible:  
Applies to vehicles with Audi connect vehi-  
cle control services: The safelock mecha-  
nism is not switched on if you use Audi con-  
nect services to lock the vehicle remotely.  
Rear notification sound  
On vehicles with indirect occupant detection, you  
can switch the notification sound for the driver  
message in the instrument cluster on/off.  
Driver messages about the anti-theft alarm  
system  
Driver messages about the occupant  
detection system  
The message Be aware of door safelock. See  
owner's manual appears on the instrument clus-  
ter display when you switch the vehicle off as a  
reminder that the safelock mechanism  
The following driver messages may appear, de-  
pending on the equipment installed in your vehi-  
cle:  
ðpage 37, Safelock will be activated.  
/ Please check rear seats!  
or  
Occupant detection  
/ Please check rear seats and be aware of  
door safelock. See owner's manual  
Introduction  
The purpose of the occupant detection system is  
to warn the driver if there could be other per-  
sons, especially children, on the rear seats after  
the vehicle has been switched off.  
At the end of each trip, a driver message will ap-  
pear on the centre display to remind you that  
someone may be seated on the rear seats. If you  
previously opened one of the rear doors, the driv-  
er message will also appear in the instrument  
cluster. Make sure that you do not leave any per-  
sons or animals behind when you leave the vehi-  
cle.  
The occupant detection system is designed to re-  
duce the risk of accidentally leaving someone be-  
hind in the vehicle.  
Before locking the vehicle, make sure that there  
are no persons or animals still in the vehicle.  
38  
Opening and closing  
For vehicles with the safelock mechanism, please  
observe ð in Information on the anti-theft  
alarm system on page 38  
Locking/unlocking the  
doors manually  
Unlocking the driver’s door manually if the  
vehicle key battery is flat  
Fig. 8 Connecting a power source  
If the 12-volt power supply fails, the doors must  
be unlocked separately.  
Connecting the central locking system to an  
emergency power supply  
The vehicle must be connected to an emergency  
power supply via the contacts in the bumper in  
order to unlock the door manually.  
Fig. 6 Driver’s door: Unlocking the electronic door handle  
manually  
Firmly press the cap inwards briefly  
ðpage 275, Fig. 149. The cap will be released  
The driver’s door must be unlocked manually if  
the vehicle key battery is flat.  
from the bumper.  
Release the two contact pins from the cap.  
Connect the positive terminal  
power source to the positive terminal  
vehicle’s contact pin (red cable).  
+
of the 12-volt  
Hold the vehicle key above the exterior door  
handle 1 in the centre with one hand.  
+
of the  
To unlock the vehicle, pull the door handle  
2
Connect the negative terminal  
of the 12-volt  
of the  
as normal with the other hand. Remove your  
hand from the door handle 3 completely after  
you have pulled it.  
Repeat this process several times at intervals of  
over 1 second until you can open the door.  
power source to the negative terminal  
vehicle’s contact pin (brown cable).  
Open the driver’s door as normal.  
Remove the terminals of the power source  
again.  
After the door has been unlocked manually, the  
vehicle key battery must be changed ðpage 42.  
Re-secure the contact pins in the cap.  
Reinsert the cap in the bumper cover.  
Open the bonnet and charge the 12-volt vehicle  
battery.  
Unlocking the driver’s door manually if the  
12-volt vehicle battery is flat  
WARNING  
The non-insulated parts of the battery clamps  
must not be allowed to touch – risk of short  
circuit.  
Fig. 7 Front bumper: Cap with 12-volt connections clipped  
into it  
39  

Related Topics

Popular Owner Manuals