Get Opening and closing -> Garage door opener Guide for Audi Rs Q8 SUV First Generation (2020-2026)

Opening and closing

switch to the first position until the roof has

reached the desired position.

Garage door opener

Description

Applies to: vehicles with garage door opener

Opening quickly

The sunroof and roof blind can also be opened at

the same time.

The garage door opener allows you to activate

garage doors, security systems, home or office

lighting and other electrical devices using control

buttons inside your car. The functions are operat-

ed on the MMI. You can program several receiv-

►

Briefly slide the  switch backwards to the

second position twice 2 .

If necessary, you can interrupt the quick opening/

closing procedure by pressing the button again.

ers, which perform the functions of up to eight

hand-held transmitters.

Closing the sunroof manually

WARNING

If a trapped object is detected in the mechanism

when the roof is closing, a safety cut-out will be

triggered and the roof will open again automati-

cally. If this happens, you can use the safety cut-

out override to close it.

– When you are operating or programming

the garage door opener, make sure that no

persons or objects are close to the devices

receiving the transmitter signals. Otherwise,

persons might be injured or other damage

caused by moving parts.

►

After the sunroof opens automatically, pull and

hold the corresponding switch within 5 seconds

until the sunroof is closed.

– Do not allow the displays and their opera-

tion to distract you from watching the traf-

fic.

WARNING

Note

– Please refer to the safety information

ðpage 39.

Before you sell your vehicle, reset the settings

– Take care when closing the roof. Careless or

uncontrolled use can cause injuries. For this

reason, always switch off the ignition and

take the key with you when you leave the ve-

hicle.

to the factory defaults ðpage 307.

Note

Before programming your system for the ga-

rage door opener, please check that it is com-

patible:

CAUTION

– You can obtain information from your quali-

fied workshop or at www.homelink.com.

There you will also find further information

on HomeLink.

Always close the roof when you leave your ve-

hicle and when it is raining or snowing to

avoid damaging the interior equipment and,

in particular, the electronic equipment.

– You can view information about HomeLink

(compatibility level/status/country code/

HomeLink generation) on the MMI:

– On the home screen, select CAR > Settings

& service > Garage door opener > .

Note

– The sunroof and the blinds can still be oper-

ated for a few minutes after the ignition is

switched off if neither of the front doors is

opened.

– The sunroof cannot be opened if the tem-

perature is too cold.

The possible number of hand-held transmitters depends

on the equipment.

Opening and closing

►

To program the garage door opener for the first

time, press the  button on the lower display.

Follow the instructions on the upper display. Or

To program further systems, select the follow-

ing on the home screen: CAR > Settings & serv-

ice > Garage door opener. Select the desired

button: + . Follow the instructions on the MMI.

To reprogram a system, select the following on

the home screen: CAR > Settings & service >

Garage door opener. Press the  button and

select  for the system you would like to re-

program. Select Program. Follow the instruc-

tions on the MMI.

Operation

Applies to: vehicles with garage door opener

Important: The relevant hand-held transmitter

must have been programmed ðpage 57, Pro-

gramming, the vehicle must be within range of

the system and the ignition must be switched on.

►

Several options are available for opening/closing

the garage door or other system.

►

If you have programmed only one hand-held

transmitter, press the  button on the lower

display. Or

►

If you have programmed more than one hand-

For some systems, the garage door opener is

available immediately after programming; for

others, it must be synchronised additionally.

held transmitter, press the  button on the

lower display, then press the appropriate but-

ton for the system. Or

►

Applies to vehicles with programmable steering

Synchronising

wheel button: If you have configured the pro-

grammable steering wheel button, press the 

button ðpage 36. Or

Applies to vehicles with GPS link: If you have

programmed the GPS link, press the appropri-

ate button on the top display (notification cen-

tre ðpage 30). The button will appear on the

MMI shortly before you reach the linked sys-

tem.

Important: You must have already programmed

the hand-held transmitter, and the vehicle must

be within range of the system (e.g. garage door).

►

To synchronise the system directly following pro-

gramming, follow the instructions on the MMI.

If you would like to synchronise at a later time:

►

Applies to MMI: On the home screen, select

CAR > Settings & service > Garage door open-

er.

Press the button for the system you would like

When transmission has been completed success-

fully, the driver message Send to: XXX will ap-

pear.

►

to synchronise.

►

Follow the instructions on the MMI.

Programming

Applies to: vehicles with garage door opener

GPS link

Applies to: vehicles with GPS link

The procedure described here is suitable for pro-

gramming both fixed code and rolling code sys-

tems on the MMI.

For more convenient operation, you can program

in the location of your system.

Important: The relevant hand-held transmitter

must have been programmed ðpage 57 and the

vehicle must be in front of the corresponding sys-

tem.

Important: The ignition must be switched on.

Programming

Applies to: MMI

Important: You must have the hand-held trans-

mitter with you, and the vehicle must be within

range of the system (e.g. garage door) you would

like to program.

►

If you have just programmed your system, fol-

low the instructions on the MMI. Or

If you wish to program the GPS link for a previ-

ously programmed system:



Applies only to rolling code systems

Opening and closing

►

Applies to MMI: On the home screen, select

CAR > Settings & service > Garage door open-

er.

– The programming process can take up to 30

seconds, and you may need to press the but-

ton on the hand-held transmitter again dur-

ing that time.

►

Press the  button.

►

Press the  button for the system your vehicle

is currently positioned in front of.

Select GPS link.

Follow the instructions on the MMI.

– It may be necessary to synchronise the ga-

rage door opener with the system after pro-

gramming. Note the instructions provided

by the manufacturer.

►

The notification centre ðpage 30 can only dis-

play up to three programmed systems. If you

would like to see all the systems, press .

Note

If a universal receiver is installed, the system

must be programmed via “UR mode”.

– Switch on the ignition.

Renaming an assignment

– Applies to MMI: On the home screen, select

CAR > Settings & service > Garage door

opener.

You can assign individual names (with up to 10

characters) to the systems you have program-

med.

– Press and hold the corresponding

ton.

but-

►

If you have just programmed your system, fol-

low the instructions on the MMI. Or

– Select Yes, in UR-Mode and follow the in-

If you wish to rename a previously programmed

system:

structions on the MMI.

►

Applies to MMI: On the home screen, select

CAR > Settings & service > Garage door open-

er.

►

Press the  button.

►

Press the  button for the system you would

like to rename.

►

Select Rename. You may have to delete the de-

fault name first (e.g. Garage door opener 1).

►

Follow the instructions on the MMI.

Deleting a system

The programmed systems can be deleted individ-

ually or all at once.

►

Applies to MMI: On the home screen, select

CAR > Settings & service > Garage door open-

er.

►

Press the  button.

►

To delete an individual system, press the 

button for the corresponding system. After the

tick mark  is set, select Delete.

►

To delete all systems, select: All > Delete.

Note

– Before programming a button, make sure

that the batteries in the hand-held trans-

mitter are charged.

Opening and closing -> Garage door opener for Your Audi Rs Q8 SUV First Generation (2020-2026)

Related Topics

Opening and closing

Popular Owner Manuals

Latest Owner Manuals