Get Controls -> Practical interior accessories Guide for BMW 1 Series 4 Door First Generation (2004-2011)

Practical interior accessories

HomeLink is a registered trademark of Johnson

Controls, Inc.

Integrated universal remote

control*

Programming

The concept

The integrated universal remote control can

replace as many as three hand-held transmit-

ters for various remote-controlled devices,

such as garage doors and gates or lighting sys-

tems. The integrated universal remote control

registers and stores signals from the original

hand-held transmitters.

The signal of an original hand-held transmitter

can be programmed on one of the three mem-

ory buttons 1. After this, the programmed

memory button 1 will operate the system in

question. The LED 2 flashes to confirm trans-

mission of the signal.

1

2

Memory buttons

LED

Fixed-code hand-held transmitters

Should you sell your vehicle one day, be sure to

delete the stored programs beforehand for your

safety, refer to page 97.

1. Switch on the ignition, refer to page 55.

2. When starting operation for the first time:

press the left and right memory buttons 1

for approx. 20 seconds until the LED 2

flashes rapidly. The three memory buttons

are cleared.

To prevent possible damage or injury,

before programming or using the inte-

grated universal remote control, always inspect

the immediate area to make certain that no peo-

ple, animals or objects are within the pivoting or

travel range of the device being operated. Com-

ply also with the safety instructions supplied

with the original hand-held transmitter.<

3. Hold the original hand-held transmitter at a

distance of approx. 4 to 12 in/10 to 30 cm

from the memory buttons 1.

The required distance between the

hand-held transmitter and the mem-

ory buttons 1 depends on the system of the

respective original hand-held transmitter

used.<

Checking compatibility

If this symbol appears on the package

or in the instructions supplied with the

original hand-held transmitter, you can

assume that the radio remote control device will

be compatible with the integrated universal

remote control.

4. Simultaneously press the transmit key on

the original hand-held transmitter and the

desired memory button 1 on the integrated

universal remote control. The LED 2 flashes

slowly at first. As soon as the LED 2 flashes

rapidly, release both buttons. If the LED 2

does not flash rapidly after approx. 15 sec-

onds, alter the distance and repeat this

step.

For additional information, please contact your

BMW center or call: 1-800-355-3515.

You can also obtain information on the Internet

at:

5. To program other original hand-held trans-

mitters, repeat steps 3 and 4.

96

The corresponding memory button 1 is now

programmed with the signal of the original

hand-held transmitter.

The corresponding memory button 1 is now

programmed with the signal of the original

hand-held transmitter.

You can operate the device while the ignition is

switched on.

If you have any questions, please contact

your BMW center.<

If the device fails to function even after

repeated programming, check whether

Deleting all stored programs

the original hand-held transmitter uses an alter-

nating-code system. To do so, either read the

instructions for the original hand-held transmit-

ter or hold down the programmed memory

button 1 of the integrated universal remote

control. If the LED 2 on the integrated universal

remote control flashes rapidly and then remains

lit for about two seconds, the original hand-held

transmitter uses an alternating-code system. If

it uses an alternating-code system, program

the memory buttons 1 as described under

Alternating-code hand-held transmitters.<

Press the left and right memory buttons 1 for

approx. 20 seconds until the LED 2 flashes rap-

idly: all stored programs are deleted.

Reassigning individual programs

1. Hold the original hand-held transmitter at a

distance of approx. 4 to 12 in/10 to 30 cm

from the memory buttons 1.

The required distance between the

hand-held transmitter and the mem-

ory buttons 1 depends on the system of the

respective original hand-held transmitter

used.<

Alternating-code hand-held

transmitters

2. Press the desired memory button 1 of the

integrated universal remote control.

To program the integrated universal remote

control, consult the operating instructions for

the device to be set. You will find information

there on the possibilities for synchronization.

When programming hand-held transmitters

that employ an alternating code, please observe

the following supplementary instructions:

3. If the LED 2 flashes slowly after approx.

20 seconds, press the transmit key of the

original hand-held transmitter. Release

both buttons as soon as the LED 2 flashes

rapidly. If the LED 2 does not flash rapidly

after approx. 15 seconds, alter the distance

and repeat this step.

Programming will be easier with the aid of

a second person.<

1. Park your vehicle within the range of the

remote-controlled device.

2. Program the integrated universal remote

control as described above in the section

Fixed-code hand-held transmitters.

3. Locate the button on the receiver of the

device to be set, e.g. on the drive unit.

4. Press the button on the receiver of the

device to be set. After step 4, you have

approx. 30 seconds for step 5.

5. Press the programmed memory button 1 of

the integrated universal remote control

three times.

97

Digital compass*

>

Press briefly: switch display on/off

3 to 6 seconds: set compass zone

6 to 9 seconds: calibrate compass

9 to 12 seconds: set left-hand/right-hand

steering

>

12 to 15 seconds: set the language

Setting compass zones

Set the compass zone corresponding to your

vehicle's geographic location so that the com-

pass can function correctly; refer to the world

map with compass zones.

1

2

Adjustment button

Display

The display shows you the main or secondary

compass direction in which you are driving.

To set the compass zone, press the adjustment

button for approx. 3-4 seconds. The number of

the compass zone set is shown in the display.

Operating principle

You can call up various functions by pressing

the adjustment button with a pointed object

such as a pen or similar item. The following

adjustment options are displayed one after the

other, depending on how long you keep the

adjustment button pressed:

To change the zone setting, briefly press the

adjustment button repeatedly until the display

shows the number of the compass zone corre-

sponding to your current location.

The compass is operational again after approx.

10 seconds.

>

An incorrect compass direction is shown.

Calibrating the digital compass

The digital compass must be calibrated in the

following situations:

98

>

The compass direction shown does not

change although the direction of travel

does.

Glove compartment

Opening

Not all compass directions are shown.

Procedure

1. Make sure that no large metal objects or

overhead power lines are in the vicinity of

your vehicle and that you have enough

space to drive in a circle.

2. Set the currently valid compass zone.

3. Convertible: ensure that the convertible top

is fully closed.

Pull the handle.

The light in the glove compartment comes on.

4. Press the adjustment button for approx.

6-7 seconds to call up C. Then drive in at

least one full circle at a speed of no more

than 4 mph or 7 km/h.

To prevent injury in the event of an acci-

dent while the vehicle is being driven,

close the glove compartment immediately after

use.<

If calibration is successful, the display

changes from C to a compass direction.

Closing

5. Convertible: open the convertible top fully

and repeat step 4.

Fold the cover up.

Setting right-hand/left-hand steering

Locking

Your digital compass is factory-set to right-

hand or left-hand steering, in accordance with

your vehicle.

To lock the glove compartment, use the inte-

grated key of the remote control, refer to

page 26.

Setting the language

USB interface for data transmission

You can set the language of the display:

Press the adjustment button for approx.

12-13 seconds. Briefly press the adjustment

button again to switch between English, "E",

and German, "O".

The setting is automatically saved after approx.

10 seconds.

Port for importing and exporting data on USB

devices, e.g. music collections, refer to

page 158.

Observe the following when connecting:

>

Do not forcibly connect the plug to the USB

interface.

>

Do not connect devices such as fans or

lamps to the USB interface.

99

>

Do not connect USB hard drives.

Items of clothing hung from the hooks

must not obstruct the driver's view. Do

not hang heavy objects from the hooks; other-

wise, they could endanger the car's occupants,

e.g. in case of heavy braking or sudden swerv-

ing.<

Do not use the USB interface to recharge

external devices.

Center armrest

Storage compartment

Cupholders

The center armrest between the front seats

contains a credit card holder and, depending on

the equipment version, a compartment or a

snap-in adapter*.

Use lightweight and shatterproof contain-

ers and do not transport hot beverages;

otherwise, there is an increased risk of injury in

the event of the accident. Do not force contain-

ers that are too large into the cupholders; other-

wise, damage could result.<

Opening

Press the button, see arrow.

There is one cupholder in the center console.

Connection for external audio device

You can connect an external audio device such

as a CD or MP3 player and play audio tracks

over the car's loudspeaker system:

>

AUX-IN port, refer to page 159

USB audio interface*/additional connection

of the music player in the mobile phone*,

refer to page 159

You can mount an attachable cupholder* on the

side of the center console.

Storagecompartmentsinside

the vehicle

Compartments are located next to the steering

column*, on the doors and in the center con-

sole.

There are nets* on the front-seat backrests.

Coupe: clothes hooks

There are clothes hooks in the rear.

100

remote control so that children cannot operate

the cigarette lighter and burn themselves.<

Ashtray*

Opening

Connecting electrical

appliances

In your BMW, when the engine is running or the

ignition is switched on, you can use electrical

devices such as a hand lamp, car vacuum

cleaner, etc., up to approx. 200 watts at

12 volts, as long as one of the following sockets

is available. Avoid damaging the socket by

attempting to insert plugs of unsuitable shape

or size.

Push the ridge on the cover.

Emptying

Cigarette lighter socket*

To access the socket:

Open the ashtray at the front and pull out the

lighter to use the socket.

In the cargo area*

To access the socket:

Fold open the cover.

In the center console

Lift out the insert.

To access the socket, refer to External devices

on page 159.

Lighter

With the engine running or the ignition switched

on, press in the cigarette lighter.

The lighter can be pulled out as soon as it pops

back out.

Hold or touch the hot cigarette lighter by

the knob only. Holding or touching it in

other areas could result in burns.

When leaving the car, always remove the

101

Coupe: through-loading

system

Convertible: cargo loading

Enlarging the cargo area

Opening

When the convertible top is closed you can

enlarge the cargo area:

To do so, fold the cargo area partition upward.

1. To release the rear seat backrest, pull the

corresponding lever in the cargo area.

Before opening the convertible top, pull the

cargo area partition down until it engages.

2. The unlocked rear seat backrest moves for-

ward slightly. Fold the backrest forward by

the head restraint.

Ensure that pointed objects do not press

against the cargo area partition from below.

The convertible top can only be opened

when the cargo area partition is folded

down.<

Storagecompartmentsinside

the cargo area

Depending on your vehicle's equipment, the

following storage spaces can be found in the

cargo area:

Closing

Return the rear seat backrest to the upright

seating position and engage it.

>

Rubber strap* on the left trim panel for

securing small objects such as a folding

umbrella

When returning the backrest into the

seating position, make sure that the

>

Net* for small objects on the right trim

seat's locking mechanism is properly engaged.

Otherwise, cargo could be thrown around and

endanger the occupants in the event of sharp

braking or swerving.<

panel of the cargo area

Retaining straps* on cargo area floor: for

securing smaller objects or as an anti-slip

surface when you place objects on the

straps

The lashing eyes in the cargo area provide you

with a way to attach cargo area nets* or draw

straps for securing suitcases and luggage, refer

to page 110.

The lashing eyes in the cargo area provide you

with a way to attach cargo area nets* or draw

straps* for securing suitcases and luggage,

refer to page 112.

102

Securing cargo

Coupe: ski bag*

The ski bag is designed for safe, clean transport

of up to 4 pairs of standard skis or up to

2 snowboards.

With the ski bag you can stow skis with a length

of up to 6.6 ft/2.0 m. When skis of 6.6 ft/2.0 m

length are loaded, the overall capacity of the ski

bag is reduced due to its tapered design.

Loading

After loading, secure the ski bag and its con-

tents. Tighten the retaining strap on the ten-

sioning buckle for this purpose.

Ensure that the skis are clean when they are

loaded into the ski bag. Wrap sharp edges to

prevent damage.

Secure the ski bag in the manner

described; otherwise, it could endanger

the car's occupants, e.g. in case of heavy brak-

ing or sudden swerving.<

1. Fold down the center panel in the rear seat

backrest.

2. Press the button, reach into the recess and

fold down the cover. To stabilize the cover

in the folded-down position, place the cen-

ter panel underneath it.

To store the ski bag, perform the steps

described for loading in reverse order.

Removing the ski bag

The ski bag can be completely removed, e.g. for

faster drying or to allow you to use other inserts.

3. Open the Velcro fastener, spread the ski

bag between the front seats and insert the

skis or snowboards.

The zip fastener makes objects in the ski

bag easier to reach.

1. Fold down the center panel in the rear seat

backrest.

4. Attach the hook of the ski bag retaining

strap to the eyelet on the side of the ski bag

opening.

2. Pull the handle, arrow 1.

3. Pull out the insert, arrow 2.

For more information on the various

inserts available, contact your BMW cen-

ter.<

103

The zip fastener makes objects in the ski

bag easier to reach.

Convertible: through-loading

opening with integrated

transport bag*

The transport bag is designed for safe, clean

transport of up to 4 pairs of standard skis or up

to 2 snowboards.

With the transport bag you can stow skis up to a

length of 6.6 ft /2.0 m. When skis of 6.6 ft/2.0 m

length are loaded, the overall capacity of the ski

bag is reduced due to its tapered design.

When using the transport bag, it is not

permissible to transport passengers in

the rear seats.<

Ensure that the skis are clean when you load

them into the transport bag. Wrap sharp edges

to prevent damage.

Loading

Securing cargo

1. Pull the grip in the filler piece of the rear

backrest up and take out the filler piece.

2. Place the filler piece onto the seat cushion

with the backrest side facing up.

After loading, secure the transport bag and its

contents. Tighten the retaining strap on the

tensioning buckle for this purpose.

Secure the transport bag in the manner

described; otherwise, it could endanger

the car's occupants, e.g. in case of heavy brak-

ing or sudden swerving.<

3. In the cargo area: press the two recesses

together and fold down the cover.

To store the transport bag, perform the steps

described for loading in reverse order.

4. Release the strap, lay out the transport bag

between the front seats and load it.

104

105

Controls -> Practical interior accessories for Your BMW 1 Series 4 Door First Generation (2004-2011)

Related Topics

Popular Owner Manuals

Latest Owner Manuals