Get Controls Guide for BMW M6 4 Door Third Generation (2012-2019)

Controls

This chapter is intended to provide you with

information that will give you complete control of

your vehicle. All features and accessories that

are useful for driving and your safety, comfort

and convenience are described here.

Controls

Opening and closing

Overview

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

1

2

3

4

Unlocking

Locking

Remote control/key

Opening the trunk lid

Press briefly: headlight courtesy delay fea‐

ture

General information

The vehicle is supplied with two remote con‐

trols with integrated key.

Press and hold: Panic mode

Every remote control holds a replaceable bat‐

tery.

Integrated key

You may set the key functions depending on

the optional features and country-specific ver‐

sion. For Settings, refer to page 42.

The vehicle stores personal settings for every

remote control. Personal Profile, refer to

page 35.

The remote controls hold information on re‐

quired maintenance. Service data in the re‐

mote control, refer to page 187

Press button, arrow 1, and remove the key, ar‐

row 2.

The integrated key fits the following locks:

▷

Driver's door.

Storage compartment in the center arm‐

rest.

The storage compartment contains a switch

for separately securing the trunk lid, refer to

page 41.

34

Opening and closing

Controls

▷

Interference of radio transmission by

charger while charging items such as mo‐

bile devices in the vehicle.

Replacing the battery

A Check Control message is displayed if an at‐

tempt is made to switch on the ignition or start

the engine.

Starting the engine with emergency

detection of the remote control

1. Remove integrated key from remote con‐

trol.

2. Push in the catch with the key, arrow 1.

3. Remove the cover of the battery compart‐

ment, arrow 2.

4. Insert a battery of the same type with the

positive side facing up.

5. Press the cover closed.

M double-clutch transmission: if a correspond‐

ing Check Control message appears, hold the

remote control, as shown, against the marked

area on the steering column and press the

Start/Stop button within 10 seconds while

pressing the brake.

Take the used battery to a recycling

center or to your service center.

New remote controls

New remote controls are available from the

service center.

Manual transmission: if a corresponding Check

Control message appears, hold the remote

control, as shown, against the marked area on

the steering column and press the Start/Stop

button within 10 seconds while pressing the

clutch pedal.

Loss of the remote controls

Lost remote controls can be disabled by your

service center.

If the remote control is not recognized: slightly

change the height position of the remote con‐

trol and repeat the procedure.

Emergency detection of remote

control

It is possible to switch on the ignition or start

the engine in situations such as the following:

▷

Interference of radio transmission to re‐

mote control by external sources e.g., by

radio masts.

Personal Profile

The concept

▷

Empty battery in remote control.

Personal Profile provides three profiles, using

which personal vehicle settings can be stored.

Every remote control has one of these profiles

assigned.

Interference from radio transmissions

through mobile devices in close proximity

to remote control.

If the vehicle is unlocked using a remote con‐

trol, the assigned personal profile will be acti‐

35

Controls

Opening and closing

vated. All settings stored in the profile are au‐

tomatically applied.

Profile management

Opening profiles

Regardless of the remote control in use a dif‐

ferent profile may be activated.

If several drivers use their own remote control,

the vehicle will adjust the personal settings

during unlocking. These settings are also re‐

stored, if the vehicle has been used in the

meantime by a person with a different remote

control.

1. "Settings"

2. "Profiles"

3. Select a profile.

Changes to the settings are automatically

saved in the personal profile.

▷

All settings stored in the called-up profile

are automatically applied.

Three personal profiles and a guest profile can

be created.

The called-up profile is assigned to the re‐

mote control being used at the time.

Adjusting

If the profile is already assigned to a differ‐

ent remote control, this profile will apply to

both remote controls. It cannot be differen‐

tiated anymore between the settings for

the two remote controls.

The settings for the following systems and

functions are saved in the active profile. The

scope of storable settings is country- and

equipment-dependable.

▷

Unlocking and locking.

Lights.

Renaming profiles

A personal name can be assigned to every pro‐

file to avoid confusion between the profiles.

Climate control.

Radio.

1. "Settings"

Instrument cluster.

Programmable memory buttons.

Volumes, tone.

Control Display.

Navigation.

2. "Profiles"

3. "Options"

4. "Rename current profile"

Resetting profiles

The settings of the active profile are reset to

their default values.

TV.

Park Distance Control PDC.

Rearview camera

Side View.

1. "Settings"

2. "Profiles"

Head-up Display.

M Drive: configurations.

3. "Options"

4. "Reset current profile"

Driver's seat position, exterior mirror posi‐

tion, steering wheel position.

Exporting profiles

▷

Intelligent Safety.

Most settings of the active profile can be ex‐

ported.

Active Blind Spot Detection.

Night vision.

This can be helpful for securing and retrieving

personal settings, before delivering the vehicle

to a workshop, e.g. Profiles can be taken to an‐

36

Opening and closing

Controls

other vehicle equipped with the Personal Pro‐

file function.

Display profile list during start

The profile list can be displayed during each

start to select the desired profile.

The following export options are available:

▷

Via BMW Online.

1. "Settings"

Via the USB port to a USB device.

2. "Profiles"

Popular file systems for USB devices are

supported. FAT32 and exFAT are the rec‐

ommended formats for profile export.

Other formats may not support the export.

3. "Options"

4. "Display user list at startup"

1. "Settings"

Using the remote control

2. "Profiles"

Note

3. "Export profile"

4. BMW Online: "BMW Online"

USB interface: "USB device"

Take the remote control with you

People or animals left unattended in a

parked vehicle can lock the doors from the in‐

side. Always take the remote control with you

when leaving the vehicle so that the vehicle

can then be opened from the outside.◀

Importing profiles

Profiles exported via BMW Online can also be

imported via BMW Online.

Profiles stored on a USB device can be im‐

ported via the USB interface.

Unlocking

Press button on the remote control.

Existing settings are overwritten with the im‐

ported profile.

▷

All doors, the tailgate, and the fuel filler flap

are being unlocked.

1. "Settings"

2. "Profiles"

Interior lamps and courtesy lamps are acti‐

vated. This function is not available, if the

interior lamps were switched off manually.

3. "Import profile"

4. BMW Online: "BMW Online"

USB interface: "USB device"

▷

The welcome lamps are switched on, if this

function was activated.

Using the guest profile

Exterior mirrors folded through convenient

closing are folded open.

The guest profile is for individual settings that

are saved in none of the three personal pro‐

files.

You can set how the vehicle is to be unlocked.

For Settings, refer to page 42.

This can be useful for drivers who are using

the vehicle temporarily and do not have their

own profile.

Anti-theft protection is switched off.

The alarm system, refer to page 44, is dis‐

armed.

1. "Settings"

2. "Profiles"

3. "Guest"

Convenient opening

Press and hold this button on the re‐

mote control after unlocking.

The guest profile cannot be renamed. It is not

assigned to the current remote control.

37

Controls

Opening and closing

The windows are opened, the glass sunroof is

tilted and the sliding visor moves back, as long

as the button on the remote control is pressed.

Opening the trunk lid

Press button on the remote control for

approx. 1 second.

Locking

The trunk lid opens, regardless of whether the

vehicle was previously locked or unlocked.

Locking from the outside

During opening, the trunk lid pivots back and

up. Ensure that adequate clearance is available

before opening.

Do not lock the vehicle from the outside

with people inside the car, as the vehicle can‐

not be unlocked from inside without special

knowledge.◀

Depending on the features and the country

version, it is also possible to have door un‐

locked. Create the settings, refer to page 42.

The driver's door must be closed.

Press button on the remote control.

If the doors were not unlocked, the trunk lid is

locked again as soon as it closes.

All doors, the tailgate, and the fuel filler flap are

being locked.

Do not place the remote control in the

cargo area

Anti-theft protection is switched on. It pre‐

vents the doors from being unlocked using the

lock buttons or the door openers.

Take the remote control with you and do not

leave it in the cargo area; otherwise, the re‐

mote control is locked inside the vehicle when

the trunk lid is closed.◀

The alarm system, refer to page 44, is armed.

Switching on interior lights and

courtesy lights

Switching on the headlight courtesy

delay feature

Press button on the remote control with

the vehicle locked.

Briefly press the button on the remote

control.

This function is not available, if the interior

lamps were switched off manually.

The duration can be set in the Control Display.

If the button is pressed again within 10 sec‐

onds after vehicle was locked, the interior mo‐

tion sensor and tilt alarm sensor of the anti-

theft warning system, refer to page 45, are

turned off. After locking, wait 10 seconds be‐

fore pressing the button again.

Malfunction

Remote control detection by the vehicle can

among others be malfunctioning under the fol‐

lowing circumstances:

▷

The battery of the remote control is dis‐

charged. Replace the battery, refer to

page 35.

Panic mode

▷

Interference of the radio connection from

transmission towers or other equipment

with high transmit power.

You can trigger the alarm system if you find

yourself in a dangerous situation.

Press button on the remote control for

at least 3 seconds.

▷

Shielding of the remote control due to

metal objects.

To reel off the alarm: press any button.

Interference of the radio connection from

mobile phones or other electronic devices

in direct proximity.

38

Opening and closing

Controls

Do not transport the remote control together

with metal objects or electronic devices.

Remove the key before pulling the door

handle

In the case of interference, the vehicle can also

be unlocked and locked from the outside with‐

out remote control, refer to page 39.

Before pulling the outside door handle, remove

the key to avoid damaging the paintwork and

the key.◀

For US owners only

The transmitter and receiver units comply with

part 15 of the FCC/Federal Communication

Commission regulations. Operation is gov‐

erned by the following:

FCC ID:

▷

LX8766S.

LX8766E.

LX8CAS.

Unlock or lock the driver's door via the door

lock using the integrated key, refer to page 34.

LX8CAS2.

MYTCAS4.

In some vehicle equipment versions, only the

driver's door can be unlocked or locked via the

door lock. In this case, the other doors must be

unlocked or locked from the inside.

Compliance statement:

This device complies with part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

Alarm system

▷

This device may not cause harmful inter‐

ference, and

With some country versions, the alarm system

is not armed if the vehicle is locked with the

integrated key.

▷

this device must accept any interference

received, including interference that may

cause undesired operation.

In some country-specific versions, the alarm

system is triggered when the vehicle is un‐

locked via the door lock.

Any unauthorized modifications or changes to

these devices could void the user's authority to

operate this equipment.

In order to terminate this alarm, unlock vehicle

with the remote control or switch on the igni‐

tion, if needed, through emergency detection

of the remote control, refer to page 35.

Without remote control

From the outside

Locking from the outside

Do not lock the vehicle from the outside

with people inside the car, as the vehicle can‐

not be unlocked from inside without special

knowledge.◀

39

Controls

Opening and closing

From the inside

Opening from the outside

Unlocking and locking

▷

Press on the top half of the BMW label.

Press button on the remote con‐

trol for approx. 1 second.

Pressing the central locking system button

locks or unlocks the vehicle with the doors

closed.

As the case may be, the doors are also un‐

locked. Unlocking with the remote control,

refer to page 38.

The vehicle is not secured against theft when

locking.

The trunk lid opens.

The fuel filler flap remains unlocked.

In the event of a severe accident, the vehicle is

automatically unlocked. The hazard warning

system and interior lights come on.

Opening from the inside

With the vehicle is stationary, press

the button in the driver's footwell.

The trunk lid opens.

Doors

Closing

Hints

Automatic Soft Closing

To close the doors, push lightly.

It is closed automatically.

Keep the closing path clear

Make sure that the closing path of the

trunk lid is clear; otherwise, injuries may re‐

sult.◀

Danger of jamming

Make sure that the closing path of the

doors is clear; otherwise, injuries may result.◀

Do not place the remote control in the

cargo area

Trunk lid

Take the remote control with you and do not

leave it in the cargo area; otherwise, the re‐

mote control is locked inside the vehicle when

the trunk lid is closed.◀

Opening

During opening, the trunk lid pivots back and

up.

Ensure that adequate clearance is available

before opening.

40

Opening and closing

Controls

Closing

Comfort Access

The concept

The vehicle can be accessed without activat‐

ing the remote control.

All you need to do is to have the remote con‐

trol with you, such as in your pants pocket.

The vehicle automatically detects the remote

control when it is in close proximity or in the

car's interior.

Recessed grips in the interior trim of the trunk

lid make it easier to pull down the lid.

Comfort Access supports the following func‐

tions:

▷

Unlocking/locking of the vehicle.

Convenient closing.

Locking separately

The trunk lid can be locked separately using

the switch in the center armrest. If the center

arm rest is locked, the trunk lid cannot be

opened.

Open the trunk lid individually.

Start the engine.

Functional requirements

▷

Trunk lid secured, arrow 1.

▷

There are no external sources of interfer‐

ence nearby.

Trunk lid not secured, ar‐

row 2.

To lock the vehicle, the remote control

must be located outside of the vehicle.

The next unlocking and locking cycle is not

possible until after approx. 2 seconds.

Slide the switch into the arrow 1 position. This

secures the trunk lid and disconnects it from

the central locking system.

The engine can only be started if the re‐

mote control is in the vehicle.

This is beneficial when the vehicle is parked

using valet service. The infrared remote con‐

trol can be handed out without the key.

Unlocking

Emergency unlocking

Grasp the handle of a vehicle door completely,

arrow.

Pull the handle inside the cargo area.

The trunk lid unlocks.

This corresponds with pressing the button on

the remote control.

41

Controls

Opening and closing

Locking

Separately unlocking the trunk lid

Press on the top half of the BMW label.

This corresponds to pressing

mote control button.

the re‐

The situation of the doors does not change.

Do not place the remote control in the

cargo area

Take the remote control with you and do not

leave it in the cargo area; otherwise, the re‐

mote control is locked inside the vehicle when

the trunk lid is closed.◀

Touch the surface on the handle of a vehicle

door, arrow, with your finger for approx. 1 sec‐

ond without grasping the door handle.

Malfunction

This corresponds with pressing the button on

the remote control.

Remote control detection by the vehicle can

among others be malfunctioning under the fol‐

lowing circumstances:

To save battery power, ensure that the ignition

and all electronic systems and/or power con‐

sumers are turned off before locking the vehi‐

cle.

▷

The battery of the remote control is dis‐

charged. Replace the battery, refer to

page 35.

▷

Interference of the radio connection from

transmission towers or other equipment

with high transmit power.

Convenient closing

Monitor closing

Monitor closing to ensure that no one

becomes trapped.◀

▷

Shielding of the remote control due to

metal objects.

Interference of the radio connection from

mobile phones or other electronic devices

in direct proximity.

Do not transport the remote control together

with metal objects or electronic devices.

In the case of a malfunction, unlock and lock

the vehicle using the buttons of the remote

control or using the integrated key, refer to

page 39.

Touch the surface on the handle of a vehicle

door, arrow, with your finger and hold it there

without grasping the door handle.

Adjusting

This corresponds to pressing and holding

the remote control button.

Unlocking

The settings are saved in the active profile, re‐

fer to page 35.

In addition to locking, the windows and the

glass sunroof close and the exterior mirrors

fold in.

42

Opening and closing

Automatic locking

Controls

Doors

1. "Settings"

2. "Doors/key"

The settings are saved in the active profile, re‐

fer to page 35.

3.

Select the symbol.

1. "Settings"

4. Select the desired function:

2. "Doors/key"

▷

"Driver's door only"

3. Select the desired function:

Only the driver's door and the fuel filler

flap are unlocked. Pressing again un‐

locks the entire vehicle.

▷

"Lock if no door is opened"

The vehicle locks automatically after a

short period of time if no door is

opened.

▷

"All doors"

The entire vehicle is unlocked.

▷

"Lock after start driving"

The vehicle locks automatically after

you drive off.

Trunk lid

Depending on optional features and country

version, this setting is not offered in some

cases.

Retrieving the seat, mirror, and

steering wheel settings

The driver's seat, exterior mirror, and steering

wheel position adjusted last will be stored for

the active profile.

1. "Settings"

2. "Doors/key"

3.

Select the symbol.

When the vehicle is unlocked, these positions

are automatically retrieved if this function was

activated.

4. Select the desired function:

▷

"Tailgate"

The trunk lid is opened.

"Tailgate + door(s)"

Pinch hazard when moving back the seat

If this function is used, first make sure

that the footwell behind the driver's seat is

empty. Otherwise, people might get injured or

objects damaged when the seat is moved

back.◀

The trunk lid is opened and the doors

are unlocked.

Confirmation signals from the vehicle

The settings are saved in the active profile, re‐

fer to page 35.

The adjustment procedure is interrupted:

▷

When a seat position reel is pressed.

1. "Settings"

When a button of the seat, mirror, and

steering wheel memory is pressed briefly.

2. "Doors/key"

3. Deactivate or activate the desired confir‐

mation signals.

Activating the setting

1. "Settings"

▷

"Acoustic sig. lock/unlock"

"Flash when lock/unlock"

2. "Doors/key"

3. "Last seat position autom."

43

Controls

Opening and closing

Indicator lamp on the interior rearview

mirror

Alarm system

The concept

When the vehicle is locked, the vehicle alarm

system responds to:

▷

Opening a door, the hood or the trunk lid.

Movements in the interior.

Changes in the vehicle tilt, e. g., during at‐

tempts at stealing a wheel or when towing

the car.

▷

Disconnected battery voltage.

▷

The indicator lamp flashes briefly every

2 seconds:

The alarm system briefly signals tampering:

The system is armed.

▷

By sounding an acoustic alarm.

The indicator lamp flashes after locking:

By switching on the hazard warning sys‐

tem.

The doors, hood or trunk lid is not closed

properly, but the rest of the vehicle is se‐

cured.

▷

By flashing the daytime running lights.

Arming and disarming the alarm

system

When you unlock or lock the vehicle, either

with the remote control, Comfort Access or at

the door lock the alarm system is disarmed or

armed at the same time.

After 10 seconds, the indicator lamp

flashes continuously. Interior motion sen‐

sor and tilt alarm sensor are not active.

When the still open access is closed, inte‐

rior motion sensor and tilt alarm sensor will

be switched on.

▷

The indicator lamp goes out after unlock‐

ing:

Door lock and armed alarm system

Unlocking via the door lock will trigger the

alarm on some country-specific versions.

The vehicle has not been tampered with.

The indicator lamp flashes after unlocking

until the engine ignition is switched on, but

no longer than approx. 5 minutes:

Trunk lid and armed alarm system

The trunk lid can be opened even when the

alarm system is armed.

An alarm has been triggered.

After the trunk lid is closed, it is locked and

monitored again when the doors are locked.

The hazard warning system flashes once.

Tilt alarm sensor

The tilt of the vehicle is monitored.

The alarm system responds in situations such

as attempts to steal a wheel or when the car is

towed.

Panic mode

You can trigger the alarm system if you find

yourself in a dangerous situation.

Interior motion sensor

The windows and glass sunroof must be

closed for the system to function properly.

Press button on the remote control for

at least 3 seconds.

To switch off the alarm: press any button.

44

Opening and closing

Controls

Avoiding unintentional alarms

The tilt alarm sensor and interior motion sen‐

sor can be switched off together, such as in

the following situations:

▷

In automatic car washes.

In duplex garages.

During transport on trains carrying vehi‐

cles, at sea or on a trailer.

▷

With animals in the vehicle.

Opening

Switching off the tilt alarm sensor and

interior motion sensor

▷

Press the button to the resistance

point.

Press the remote control button again

within 10 seconds as soon as the vehicle

is locked.

The window opens while the switch is held.

▷

Press the switch beyond the resist‐

ance point.

The indicator lamp lights up for approx. 2 sec‐

onds and then continues to flash.

The window opens automatically. Pressing

the switch again stopse the motion.

The tilt alarm sensor and interior motion sen‐

sor are turned off, until the vehicle is locked

again.

See also: Convenient opening, refer to

page 37, via remote control.

Switching off the alarm

Closing

▷

Unlock vehicle with the remote control or

switch on the ignition, if needed through

emergency detection of remote control, re‐

fer to page 35.

Keep the closing path clear

Monitor closing and make sure that the

closing path of the window is clear; otherwise,

injuries may result.◀

▷

With Comfort Access: if you are carrying

the remote control on your person, grasp

the driver side or front passenger side door

handle completely.

▷

Pull the switch to the resistance

point.

The window closes while the switch is

held.

Power windows

▷

Pull the switch beyond the resistance

point.

Hint

The window closes automatically. Pulling

again stops the motion.

Take the remote control with you

Take the remote control with you when

leaving the vehicle so that children, e.g., can‐

not operate the power windows and injure

themselves.◀

See also: closing by means of Comfort Access,

refer to page 41.

45

Controls

Opening and closing

blocked for a limited time to prevent overheat‐

ing. Let the system cool.

Pinch protection system

Danger of jamming even with pinch pro‐

tection

The roller sunblind for the rear window cannot

be moved at low interior temperatures.

Even with the pinch protection system, check

that the window's closing path is clear; other‐

wise, the closing action may not stop in certain

situations, e.g., if thin objects are present.◀

Driver's door controls

No window accessories

Do not install any accessories in the win‐

dow's range of movement; otherwise, the

pinch protection system will be impaired.◀

If closing force exceeds a specific margin as a

window closes, closing is interrupted.

The window reopens slightly.

Roller sunblind for rear window

Closing without the pinch protection

system

Press button.

Keep the closing path clear

Monitor closing and make sure that the

closing path of the window is clear; otherwise,

injuries may result.◀

Glass sunroof, powered with

tilt function

E.g. danger from the outside or ice might pre‐

vent window from closing properly - proceed

as follows:

General information

The glass sunroof and the sliding visor can be

operated together or separately, using the

same switch.

1. Pull the reel past the resistance point and

hold it there.

The glass sunroof is operational when the igni‐

tion is switched on.

The pinch protection is limited and the

window reopens slightly if the closing force

exceeds a certain margin.

Keep the closing path clear

Monitor closing and make sure that the

closing path of the glass sunroof is clear; oth‐

erwise, injuries may result.◀

2. Pull the reel past the resistance point again

within approx. 4 seconds and hold it there.

The window closes without jam protection.

Take the remote control with you

Take the remote control with you when

leaving the vehicle so that children, e.g., can‐

not operate the glass sunroof and injure them‐

selves.◀

Roller sunblind

General information

If you are no longer able to move the roller sun‐

blind for the rear window after having activated

it a number of times in a row, the system is

46

Opening and closing

Controls

Pinch protection system

If the closing force exceeds a specific value as

a glass sunroof closes, the closing action is in‐

terrupted.

The glass sunroof is tilted again.

Danger of jamming even with pinch pro‐

tection

Despite the pinch protection system, check

that the glass sunroof's closing path is clear;

otherwise, the closing action may not be inter‐

rupted in certain extreme situations, such as

when thin objects are present.◀

Tilting up and closing glass sunroof

▷

Push switch briefly upward.

The closed glass sunroof is

tilted and the sliding visor

opens slightly.

Closing without the pinch protection

system

▷

Briefly press out the reel

twice in succession toward

the rear past the resistance

point.

If there is an external danger or if, e. g., icing

prevents automatic closing, push the reel for‐

ward past the resistance point and hold it.

The glass sunroof closes without jam protec‐

tion. Make sure that the closing area is clear.

Closed glass sunroof is tilted

and the sliding visor moves

all the way back.

Initializing after a power failure

▷

To close the reel, press upward briefly or

twice forward past the resistance point.

After a power failure during the opening or

closing process, the glass sunroof can only be

operated to a limited extent.

Additional options:

▷

Convenient opening, refer to page 37, via

the remote control.

Initializing the system

The system can be initialized when the vehicle

is stationary and the engine is running.

▷

Closing by means of Comfort Access, refer

to page 41.

During the initialization, the glass sunroof

closes without jam protection.

Opening/closing the sliding visor

Keep the closing path clear

▷

Press the reel in the desired

direction to the resistance

point and hold it there.

Monitor closing and make sure that the

closing path of the glass sunroof is clear; oth‐

erwise, injuries may result.◀

The sliding visor moves, as

long as the reel is held

down.

Press the reel up and hold it until

the initialization is complete:

▷

Press the reel in the desired direction past

the resistance point.

▷

Initialization begins within

15 seconds and is com‐

pleted when the glass sun‐

The sliding visor moves automatically.

Pressing the reel upward stops the motion.

47

Controls

Opening and closing

roof and sliding visor are

completely closed.

▷

The glass sunroof closes without jam pro‐

tection.

48

Adjusting

Controls

Adjusting

Keep the movement area unobstructed

Vehicle features and options

When changing the seat position, keep

the seat's area of movement unobstructed;

otherwise, people might get injured or objects

damaged.◀

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

At a glance

Sitting safely

The ideal seating position can make a vital

contribution to relaxed, fatigue-free driving.

The seating position plays an important role in

an accident in combination with:

1

2

3

4

5

6

7

8

Active seat

Seat, mirror, and steering wheel memory

Backrest width

▷

Safety belts, refer to page 52.

Head restraints, refer to page 53.

Airbags, refer to page 100.

Lumbar support

Backrest, head restraint

Shoulder support

Seats

Forward/back, height, tilt

Thigh support

Hints

Do not adjust the seat while driving

General information

Do not adjust the driver's seat while driv‐

ing, or the seat could respond with unexpected

movement and the ensuing loss of vehicle

control could lead to an accident.◀

The seat setting for the driver's seat is stored

for the profile currently in use. When the vehi‐

cle is unlocked via the remote control, the po‐

sition is automatically retrieved if the Function,

refer to page 43, is activated for this purpose.

Do not incline the backrest too far to the

rear

Do not incline the backrest too far to the rear

while driving, or there is a risk of slipping under

the safety belt in the event of an accident. This

would eliminate the protection normally pro‐

vided by the belt.◀

49

Controls

Adjusting

Adjustments in detail

Thigh support

1. Forward/back.

Multifunctional seat

2. Height.

Adjust the position using the lever.

Lumbar support

The curvature of the seat backrest can be ad‐

justed in a way that it supports the lumbar re‐

gion of the spine. The lower back and the

spine are supported for upright posture.

▷

Press the front/rear section

of the switch.

The curvature is increased/

decreased.

3. Seat tilt.

▷

Press the upper/lower sec‐

tion of the switch.

The curvature is shifted up/

down.

Backrest width

Change the width of the back‐

rest using the side wings to ad‐

just the lateral support.

4. Backrest tilt.

To make it easier to enter and exit the vehicle,

the backrest width temporarily opens fully.

50

Adjusting

Controls

Shoulder support

Switching on

Press button once for each tempera‐

ture level.

The maximum temperature is reached when

three LEDs are lit.

If the journey is continued within approx. 15

minutes, the seat heating is activated automat‐

ically with the temperature selected last.

Switch off

Also supports the back in the shoulder area:

Press button longer.

The LEDs go out.

▷

Results in a relaxed seating position.

Reduces strain on the shoulder muscles.

Temperature distribution

Active seat

The heating action in the seat cushion and

backrest can be distributed in different ways.

Active adjustment of the seat cushion's con‐

tours reduces muscular tension and fatigue to

help prevent lower back pain.

On the Control Display:

1. "Climate"

2. "Front seat heating"

3. Select the required seat.

4. Turn the controller to set the temperature

distribution.

Active seat ventilation, front

The seat cushion and backrest surfaces are

cooled by means of integrated fans.

Press button. The LED lights up.

The ventilation cools the seat, e. g., if the vehi‐

cle interior is overheated or for continuous

cooling at high temperatures.

Front seat heating

51

Controls

Adjusting

Switching on

Hints

Press button once for each ventilation

level.

One person per safety belt

Never allow more than one person to

wear a single safety belt. Never allow infants or

small children to ride on a passenger's lap.◀

The highest level is active when three LEDs

are lit.

After a short time, the system automatically

moves down one level in order to prevent ex‐

cessive cooling.

Putting on the belt

Lay the belt, without twisting, snugly

across the lap and shoulders, as close to the

body as possible. Make sure that the belt lies

low around the hips in the lap area and does

not press on the abdomen. Otherwise, the belt

can slip over the hips in a frontal impact and in‐

jure the abdomen.

Switch off

Press button longer.

The LEDs go out.

The safety belt must not lie across the neck,

rub on sharp edges, be routed over breakable

objects, or be pinched.◀

Safety belts

Seats with safety belt

The vehicle has four seats, each of which is

equipped with a safety belt.

What reduces the restraining effect

Avoid wearing bulky clothing, and pull

the shoulder belt periodically to readjust the

tension. Make sure that the belt is not jammed;

otherwise, the belt can be damaged and the

restraining effect is reduced.◀

General information

Always make sure that safety belts are being

worn by all occupants before driving off.

For the occupants' safety the belt locking

mechanism triggers early. Slowly guide the

belt out of the holder when applying it.

Buckling the belt

Although airbags enhance safety by providing

added protection, they are not a substitute for

safety belts.

The upper shoulder strap's anchorage point

will be correct for adult seat occupants of ev‐

ery build if the seat is correctly adjusted.

▷

The two outer safety belt buckles,

integrated into the rear seat, are for pas‐

sengers sitting on the left and right.

Make sure you hear the latch plate engage in

the belt buckle.

▷

The center rear safety belt buckle is solely

intended for the center passenger.

Tensioning the safety belt

automatically

When the belt is closed, it is automatically

tightened once after the release.

52

Adjusting

Controls

Unbuckling the belt

1. Hold the belt firmly.

Front headrests

Correctly adjusted head restraint

2. Press the red button in the belt buckle.

3. Guide the belt back into its roll-up mecha‐

nism.

General information

A correctly adjusted head restraint reduces the

risk of injury to cervical vertebrae in the event

of an accident.

Safety belt reminder for driver's and

passenger's seat

The indicator lamp lights up and a sig‐

nal sounds. Make sure that the safety

belts are positioned correctly. The

safety belt reminder is active at speeds above

approx. 6 mph/10 km/h. It can also be activated

if objects are placed on the front passenger

seat.

Note

Adjusting the head restraint

Adjust the head restraints of all occupied

seats properly; otherwise, there is an increased

risk of injury in an accident.◀

Height

Safety mode

Adjust the head restraint so that its center is

approximately at ear level.

In critical situations, e.g., during full brake ap‐

plication, the front safety belts tighten auto‐

matically.

Distance

Adjust the distance so that the head restraint

is as close as possible to the back of the head.

If the situation passes without an accident oc‐

curring, the belt tension relaxes.

If the belt tension does not loosen automati‐

cally, stop the vehicle and unbuckle the belt

using the red button in the buckle. Fasten the

belt before continuing on your trip.

Active head restraint

In the event of a rear-end collision with a cer‐

tain severity, the active head restraint automat‐

ically reduces the distance from the head.

Damage to safety belts

Reduced protective function

Wear and tear after accidents or when dam‐

aged otherwise:

▷

Do not use seat or head restraint

covers.

Have the safety belts, including the safety belt

tensioners, replaced and have the belt anchors

checked.

▷

Do not hang objects, e.g., clothes hangers,

on the head restraints.

Only attach accessories approved by BMW

to the seat or head restraint.

Check and replace safety belts

This should only be done by your service

center; otherwise, this safety feature might not

work properly.◀

Otherwise, the protective function of the active

head restraint will be impaired and the per‐

sonal safety of the occupants will be endan‐

gered.◀

Wear and tear after accidents or when dam‐

aged otherwise:

Have the active headrest checked and if

needed replaced.

53

Controls

Adjusting

Adjusting the height

Entering the rear

Note

Keep the movement area unobstructed

When changing the seat position, keep

the seat's area of movement unobstructed;

otherwise, people might get injured or objects

damaged.◀

Folding back and locking the backrest

Adjusting electrically.

Before driving off, fold back and lock the

backrests; otherwise, an unexpected seat

movement may cause an accident.◀

Distance to the back of the head

Unlocking the backrest

▷

Forward: pull.

Back: press the button and push the head

restraint toward the rear.

1. Pull lever up to the stop.

2. Fold backrest forward.

Adjusting the side extensions

Changing the seat position

Requirements

▷

Vehicle at a standstill.

When the door is open, the seat is accessi‐

ble from the side on which the door is

open.

Fold forward for increased lateral support in

the resting position.

Removing

The head restraints cannot be removed.

54

Adjusting

Controls

Keep the movement area unobstructed

Controls

When changing the seat position, keep

the seat's area of movement unobstructed;

otherwise, people might get injured or objects

damaged.◀

At a glance

▷

Press and hold this button until the seat

has moved to the desired position. Releas‐

ing the button stops window/roof move‐

ment.

Press button briefly. The seat automati‐

cally moves to the respective end position.

Pressing again stops the motion.

Storing

1. Switch on the ignition.

2. Set the desired position.

Folding back and locking the backrest

After entering the rear, fold the backrest back

and lock it.

3.

Press button. The LED in the but‐

ton lights up.

Press button. The seat moves to its origi‐

nal position. Pressing again stops the

motion.

4. Press selected button 1 or 2 while the LED

is lit. The LED goes out.

If the SET button is pressed accidentally:

Press button again.

The LED goes out.

Seat, mirror, and steering

wheel memory

The concept

Calling up settings

Two driver's seat and exterior mirror positions

can be stored per profile, refer to page 35, and

called up. Settings for the backrest width and

lumbar support are not stored in memory.

Comfort function

1. Open the driver's door.

2. Switch off the ignition.

3. Briefly press the desired button 1 or 2.

Hints

The corresponding seat position is performed

automatically.

Do not retrieve the memory while driving

Do not retrieve the memory setting while

driving, as an unexpected movement of the

seat could result in an accident.◀

The procedure stops when a reel for adjusting

the seat or one of the buttons is pressed.

55

Controls

Adjusting

Safety mode

At a glance

1. Close the driver's door or reel on the igni‐

tion.

2. Press and hold the desired button 1 or 2

until the adjustment procedure is com‐

pleted.

Calling up of a seat position

deactivated

After a brief period, calling up stored seat posi‐

tions is deactivated to save battery power.

1

2

3

Adjustingꢀꢁ56

To reactivate calling up of a seat position:

Left/right, Automatic Curb Monitor

Fold in and outꢀꢁ57

▷

Open or close the door or trunk lid.

Press a button on the remote control.

Press the Start/Stop button.

Selecting a mirror

To change over to the other mirror:

Slide the switch.

Mirrors

Adjusting electrically

Exterior mirrors

The setting corresponds to the direc‐

tion in which the button is pressed.

General information

The mirror on the passenger side is more

curved than the driver's side mirror.

Saving positions

Seat, mirror, and steering wheel memory, refer

to page 55.

Depending on the vehicle equipment, the mir‐

ror setting is stored for the profile currently in

use. When the vehicle is unlocked via the re‐

mote control, the position is automatically re‐

trieved if this function is active.

Adjusting manually

In case of electrical malfunction press edges of

mirror.

Note

Estimating distances correctly

Automatic Curb Monitor

The concept

Objects reflected in the mirror are closer

than they appear. Do not estimate the distance

to the traffic behind you based on what you

see in the mirror, as this will increase your risk

of an accident.◀

If reverse gear is engaged, the mirror glass on

the front passenger side is tilted downward.

This improves your view of the curb and other

low-lying obstacles when parking, e.g.

56

Adjusting

Controls

Activating

Interior rearview mirror, automatic

dimming feature

1.

Slide the switch to the driver's side

mirror position.

The concept

2. Engage selector lever position R.

Deactivating

Slide the switch to the passenger side mirror

position.

Fold in and out

Press button.

Photocells are used for control:

Possible at speeds up to approx.

15 mph/20 km/h.

▷

In the mirror glass.

On the back of the mirror.

E. g. this is advantageous

▷

In car washes.

Functional requirement

For proper operation:

In narrow streets.

For folding mirrors back out that were

folded away manually.

▷

Keep the photocells clean.

Mirrors that were folded in are folded out auto‐

matically at a speed of approx.

25 mph/40 km/h.

Do not cover the area between the inside

rearview mirror and the windshield.

Fold in the mirror in a car wash

Steering wheel

Before washing the car in an automatic

car wash, fold in the exterior mirrors by hand or

with the button; otherwise, the mirrors could

be damaged, depending on the width of the

vehicle.◀

Note

Do not adjust while driving

Do not adjust the steering wheel while

driving; otherwise, an unexpected movement

could result in an accident.◀

Automatic heating

Both exterior mirrors are automatically heated

whenever the engine is running.

Automatic dimming feature

Both exterior mirrors are automatically dim‐

med. Photocells are used to control the Interior

rearview mirror, refer to page 57.

57

Controls

Adjusting

The steering wheel can be adjusted in four di‐

rections.

Storing the position

Seat, mirror, and steering wheel memory, refer

to page 55.

Assistance getting in and out

The steering wheel temporarily moves into the

highest position to make it easier to enter and

exit the vehicle.

Steering wheel heating

Press button.

▷

On: the LED lights up.

Off: the LED goes out.

If the trip is resumed within approx. 15 min,

steering wheel heating is automatically acti‐

vated again.

58

Transporting children safely

Controls

Transporting children safely

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

The right place for children

Note

Children in the vehicle

Deactivating the front-seat passenger

airbags

Do not leave children unattended in the

vehicle; otherwise, they could endanger them‐

selves and other persons, e.g., by opening the

doors.◀

If a child restraint system is used in the front

passenger seat, deactivate the front-seat pas‐

senger airbags; otherwise, there is an in‐

creased risk of injury to the child when the air‐

bags are activated, even with a child restraint

system.◀

Children should always be in the rear

Accident research shows that the safest place

for children is in the back seat.

Transporting children in the rear

Installing child restraint

systems

Only transport children younger than

13 years of age or shorter than 5 ft/150 cm in

the rear in child restraint systems provided in

accordance with the age, weight and size of

the child; otherwise, there is an increased risk

of injury in an accident.

Hints

Manufacturer's information for child re‐

straint systems

To select, mount and use child restraint sys‐

tems, observe the information provided by the

system manufacturer; otherwise, the protec‐

tive effect can be lost.◀

Children 13 years of age or older must wear a

safety belt as soon as a suitable child restraint

system can no longer be used due to their age,

weight and size.◀

Ensuring the stability of the child seat

Children on the front passenger seat

When installing child restraint systems,

make sure that the child seat is securely fas‐

tened to the backrest of the seat. Angle and

headrest of the backrest might need to be ad‐

justed or possibly be removed. Make sure that

all backrests are securely locked. Otherwise

the stability of the child seat can be affected,

and there is an increased risk of injury because

Should it ever be necessary to use a child re‐

straint system in the front passenger seat,

make sure that the front, knee and side airbags

on the front passenger side are deactivated.

Automatic deactivation of front-seat passen‐

ger airbags, refer to page 102.

59

Controls

Transporting children safely

of unexpected movement of the seat back‐

rest.◀

the adjustment after this; otherwise, the stabil‐

ity of the child seat will be reduced.◀

Adjustable backrest width: before installing a

child restraint system in the front passenger

seat, open the backrest width completely. Do

not change the backrest width again and do

not call up a memory position.

On the front passenger seat

Deactivating airbags

Deactivating the front-seat passenger

airbags

Child seat security

If a child restraint system is used in the front

passenger seat, deactivate the front-seat pas‐

senger airbags; otherwise, there is an in‐

creased risk of injury to the child when the air‐

bags are activated, even with a child restraint

system.◀

After installing a child restraint system in the

front passenger seat, make sure that the front,

knee and side airbags on the front passenger

side are deactivated.

The rear safety belts and the front passenger

safety belt can be permanently locked to fas‐

ten child restraint systems.

Deactivate the front-seat passenger airbags

automatically, refer to page 102.

The front passenger safety belt can be perma‐

nently locked to fasten child restraint systems.

Seat position and height

Before installing a child restraint system, move

the front passenger seat as far back as possi‐

ble and adjust its height to the highest and

thus best possible position for the belt and to

offer optimal protection in the event of an acci‐

dent.

Locking the safety belt

1. Pull out the strap completely.

2. Secure the child restraint system with the

belt.

If the upper anchorage of the safety belt is lo‐

cated in front of the belt guide of the child seat,

move the passenger seat carefully forward un‐

til the best possible belt guide position is

reached.

3. Allow the strap to be pulled in and pull it

tight against the child restraint system.

The safety belt is locked.

Unlocking the safety belt

1. Unbuckle the belt buckle.

Backrest width

2. Remove the child restraint system.

3. Allow the strap to be pulled in completely.

Backrest width for the child seat

Before installing a child restraint system

in the front passenger seat, the backrest width

must be opened completely. Do not change

60

Transporting children safely

Controls

LATCH child restraint system

LATCH: Lower Anchors and Tether for Chil‐

dren.

Before installing LATCH child

restraint systems

Pull the belt away from the area of the child re‐

straint system.

Note

Follow manufacturer's information for

LATCH child restraint systems

Assembly of LATCH child restraint

systems

1. Mount the child restraint system; refer to

the user's manual of the system.

To mount and use the LATCH child restraint

systems, observe the operating and safety in‐

formation from the system manufacturer; oth‐

erwise, the level of protection may be re‐

duced.◀

2. Ensure that both LATCH anchors are prop‐

erly connected.

Child restraint fixing system with a

tether strap

Mounts for the lower LATCH anchors

The lower anchors may be used to attach the

CRS to the vehicle seat up to a combined child

and CRS weight of 65 lb/30 kg when the child

is restrained by the internal harnesses.

Mounting points

The respective symbol shows the an‐

chor for the upper retaining strap.

Seats with an upper Top Tether are

Note

marked with this symbol. It can be found on

the rear seat backrest or the rear window shelf.

Properly engage the lower LATCH an‐

chors

Make sure that the lower LATCH anchors have

properly engaged and that the child restraint

system is resting snugly against the backrest;

otherwise, the degree of protection may be re‐

duced.◀

Note

Mounting eyelets

Use the mounting eyes only for the up‐

per retaining strap to secure child restraint

systems; otherwise, the mounting eyes could

be damaged.◀

Position

The corresponding symbol shows the

mounts for the lower LATCH anchors.

Seats equipped with lower anchors are

marked with a pair, 2, of LATCH sym‐

bols. It is not recommended to use the

inner lower anchors of standard outer

LATCH positions to fasten a child restraint

system on the middle seat. Use the vehicle

seat belt instead for the middle seat.

Retaining strap guide

Retaining strap

Make sure the upper retaining strap does

not run over sharp edges and is not twisted as

it passes to the top anchor. Otherwise, the

strap will not properly secure the child restraint

system in the event of an accident.◀

61

Controls

Transporting children safely

1

2

3

4

5

6

Direction of travel

Upper retaining strap

Head restraint

Rear window shelf

Mounting point/eye

Hook for upper retaining strap

Attaching the upper retaining strap to

the mounting point

1. Lift the cover over the mounting point.

2. Guide the upper retaining strap over the

head restraint.

3. Attach the hook of the retaining strap to

the mounting eye.

4. Tighten the retaining strap by pulling it

down.

62

Driving

Controls

Driving

Ignition off

Vehicle features and options

M double-clutch transmission: Press the Start/

Stop button again without stepping on the

brake.

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Manual transmission: Press the Start/Stop but‐

ton again without stepping on the clutch pedal.

All indicator lights in the instrument cluster go

out.

To save battery power when the engine is off,

switch off the ignition and any unnecessary

electronic systems/power consumers.

P when the ignition is switched off

Start/Stop button

P is engaged automatically when the ig‐

nition is switched off. When in an automatic car

wash, e.g., ensure that the ignition is not

switched off accidentally.◀

The concept

Pressing the Start/Stop button

switches the ignition on or off

and starts the engine.

The ignition automatically cuts off while the

vehicle is stationary and the engine is stopped:

M Double-clutch transmission:

The engine starts if the brakes

are stepped on while pressing the Start/Stop

button.

▷

When locking the vehicle, and when the

low beams are activated.

▷

Shortly before the battery is discharged

completely, so that the engine can still be

started. This function is only available

when the low beams are turned off.

Manual transmission: The engine starts with

the clutch pedal pressed when the Start/Stop

button is pressed.

▷

When opening or closing the driver door, if

the driver's safety belt is unbuckled and

the low beams are turned off.

Ignition on

M double-clutch transmission: Press the Start/

Stop button without stepping on the brake.

While the driver's safety belt is unbuckled

with driver's door open and low beams off.

Manual transmission: Press the Start/Stop but‐

ton without stepping on the clutch pedal.

The low beams switch to parking lights after

approx. 15 minutes of no use.

All vehicle systems are ready for operation.

Most of the indicator and warning lights in the

instrument cluster light up for a varied length

of time.

Radio ready state

Activate radio-ready state:

▷

When the engine is running: press the

Start/Stop button.

To save battery power when the engine is off,

switch off the ignition and any unnecessary

electronic systems/power consumers.

Some electronic systems/power consumers

remain ready for operation.

63

Controls

Driving

The radio-ready state switches off automati‐

cally:

Repeated starting in quick succession

Avoid trying to start the vehicle repeat‐

edly and in quick succession. Otherwise, the

fuel is not burned or is inadequately burned,

posing a risk of overheating and damage to the

catalytic converter.◀

▷

After approx. 8 minutes.

When the vehicle is locked using the cen‐

tral locking system.

▷

Shortly before the battery is discharged

completely, so that the engine can still be

started.

Do not wait for the engine to warm-up while

the vehicle remains stationary. Start driving at

moderate engine speeds.

The radio-ready state remains active if, e.g.,

the ignition is automatically switched off for the

following reasons:

M double-clutch transmission

▷

Opening or closing the driver's door.

Unfastening of the driver's safety belt.

Starting the engine

1. Depress the brake pedal.

2. Press the Start/Stop button.

When automatically switching from low

beams to parking lights.

The ignition is activated automatically for a

certain time and is stopped as soon as the en‐

gine starts.

If the engine is switched off and the ignition is

switched on, the system automatically

switches to the radio-ready state if the lights

are turned off or, if correspondingly equipped,

the daytime running lights are activated.

Manual transmission

Starting the engine

1. Depress the brake pedal.

Starting the engine

2. Press on the clutch pedal and shift to neu‐

tral.

Hints

3. Press the Start/Stop button.

Enclosed areas

The ignition is activated automatically for a

certain time and is stopped as soon as the en‐

gine starts.

Do not let the engine run in enclosed

areas, since breathing in exhaust fumes may

lead to loss of consciousness and death. The

exhaust gases contain carbon monoxide, an

odorless and colorless but highly toxic gas.◀

Engine stop

Unattended vehicle

Hints

Do not leave the vehicle unattended with

the engine running; doing so poses a risk of

danger.

Take the remote control with you

Take the remote control with you when

leaving the vehicle so that children, e.g., can‐

not start the engine.◀

Before leaving the vehicle with the engine run‐

ning, set the parking brake and engage trans‐

mission position P; otherwise, the vehicle may

begin to move.◀

Apply parking brake and further secure

the vehicle if needed.

Set the parking brake firmly when parking; oth‐

erwise, the vehicle could roll. On steep upward

64

Driving

Controls

and downward inclines, further secure the ve‐

hicle, e.g., by turning the steering wheel in the

direction of the curb.◀

is available when the vehicle is traveling faster

than about 3 mph, approx. 5 km/h.

Engine stop

The engine is switched off automatically dur‐

ing a stop under the following conditions:

Before driving into a car wash

So that the vehicle can roll into a car wash ob‐

serve instructions for going into an automatic

car wash, refer to page 200.

M double-clutch transmission:

▷

The selector lever is in selector lever posi‐

tion D.

M double-clutch transmission

Switching off the engine

1. Apply the brakes until the vehicle comes to

a stop.

Brake pedal remains depressed while the

vehicle is stopped.

The driver's safety belt is buckled or the

driver's door is closed.

Manual transmission:

2. Press the Start/Stop button.

The engine is switched off.

▷

Neutral is engaged and the clutch pedal is

not pressed.

The radio-ready state is switched on.

3. Set the parking brake.

▷

The driver's safety belt is buckled or the

driver's door is closed.

The air flow from the air conditioner is reduced

when the engine is switched off.

Manual transmission

Switching off the engine

1. With the vehicle at a standstill, press the

Start/Stop button.

Displays in the instrument cluster

The display indicates that the

Auto Start/Stop function is

ready for an Automatic engine

start.

2. Shift into first gear or reverse.

3. Set the parking brake.

The display indicates that the

conditions for an automatic en‐

gine stop have not been met.

Auto Start/Stop function

The concept

The Auto Start/Stop function helps save fuel.

The system switches off the engine during a

stop, e.g., in traffic congestion or at traffic

lights. The ignition remains switched on. The

engine starts again automatically for driving

off.

Functional limitations

The engine is not switched off automatically in

the following situations:

▷

External temperature too low.

The external temperature is high and auto‐

matic climate control is running.

Semi-automatic mode

After every start of the engine using the Start/

Stop button, the Auto Start/Stop function is in

the last selected state, refer to page 67.

▷

The car's interior has not yet been heated

or cooled to the required level.

When the Auto Start/Stop function is active, it

65

Controls

Driving

▷

The engine is not yet at operating temper‐

ature.

▷

The steering wheel is turned.

Double-clutch transmission: Change from

selector lever position D to N, R or D/S.

The wheels are at a sharp angle or the

steering wheel is being turned.

▷

M double-clutch transmission: Accelerat‐

ing while simultaneously applying the

brake.

▷

After driving in reverse.

Fogging of the windows when the auto‐

matic climate control is switched on.

▷

The vehicle begins rolling.

▷

Vehicle battery is heavily discharged.

At higher elevations.

Fogging of the windows when the auto‐

matic climate control is switched on.

▷

Vehicle battery is heavily discharged.

The engine compartment lid is unlocked.

Stop-and-go traffic.

Excessive cooling of the car's interior when

the heating is switched on.

Use of fuel with high ethanol content.

▷

Low brake vacuum pressure; this can oc‐

cur, e.g., if the brake pedal is depressed a

number of times in succession.

Starting the engine

The engine starts automatically under the fol‐

lowing conditions:

Preventing an automatic engine stop

with aM double-clutch transmission

▷

M double-clutch transmission:

By releasing the brake pedal.

Manual transmission:

The concept

▷

To make it possible to drive off very quickly,

such as at an intersection, the automatic en‐

gine stop can be actively prevented.

The clutch pedal is pressed.

After the engine starts, accelerate as usual.

Safety mode

Preventing an engine stop using the

brake pedal

The engine stop can be actively prevented

within one second after the vehicle comes to a

standstill.

After the engine switches off automatically, it

will not start again automatically if any one of

the following conditions are met.

▷

The driver's safety belt is unbuckled and

the driver's door is open.

▷

Immediately after the vehicle comes to a

standstill, briefly press the brake pedal

forcefully.

▷

The hood was unlocked.

Some indicator lights light up for a varied

length of time.

▷

Then press the brake pedal with normal

braking force.

The engine can only be started via the Start/

Stop button.

Functional limitations

Even if driving off was not intended, the deacti‐

vated engine starts up automatically in the fol‐

lowing situations:

▷

Excessive warming of the car's interior

when the cooling function is switched on.

66

Driving

Controls

Activating/deactivating the system

manually

Malfunction

The Auto Start/Stop function no longer

switches off the engine automatically. A Check

Control message is displayed. It is possible to

continue driving. Have the system checked.

Using the button

Parking brake

The concept

The parking brake is used to prevent the vehi‐

cle from rolling when it is parked.

Overview

Press button.

▷

LED comes on: Auto Start/Stop function is

deactivated.

The engine is started during an automatic

engine stop.

The engine can only be stopped or started

via the Start/Stop button.

LED goes out: Auto Start/Stop function is

activated.

Parking brake

Switching off the vehicle during an

automatic engine stop

During an automatic engine stop, the vehicle

can be switched off permanently, e. g., when

leaving it.

Setting

Apply parking brake and further secure

the vehicle if needed.

Set the parking brake firmly when parking; oth‐

erwise, the vehicle could roll. On steep upward

and downward inclines, further secure the ve‐

hicle, e.g., by turning the steering wheel in the

direction of the curb.◀

1. Press the Start/Stop button. The ignition is

switched off. The Auto Start/Stop function

is deactivated.

P is engaged automatically.

2. Set the parking brake.

Take the remote control with you

Engine start as usual via Start/Stop button.

Take the remote control with you when

leaving the vehicle so that children, e.g., can‐

not release the parking brake.◀

Automatic deactivation

In certain situations, Auto Start/Stop function

is deactivated automatically for safety reasons

as if the driver were absent.

Pull the reel.

The LED lights up.

67

Controls

Driving

The indicator lamp lights up red. The

parking brake is set.

▷

Drive mode engaged.

Driver buckled in and doors closed.

Automatic release in cars with manual

transmission

Drive off as usual. The parking brake disen‐

gages when the clutch pedal is released.

While driving

Use as emergency brake while driving:

Pull the reel and hold it. The vehicle brakes

hard while the reel is being pulled.

The LED and indicator lamp go out.

The indicator lamp lights up red, a sig‐

nal sounds and the brake lights light

up.

Under the following conditions, the parking

brake is automatically released:

▷

Engine on.

A Check Control message is displayed.

Gear engaged.

If the vehicle is slowed down down to a speed

of approx. 2 mph/3 km/h the parking brake is

set.

Driver buckled in and doors closed.

Engine power is sufficient to drive off.

Inadvertent operation of the clutch pedal

Make sure that the clutch pedal is not

Releasing

With the ignition switched on:

operated unintentionally; otherwise, the vehi‐

cle is set in motion when the clutch is released,

and there is a risk of an accident.◀

Manual transmission: Press the switch

while the brake or clutch pedal is

pressed.

Malfunction

M double-clutch transmission: Press the

switch while pressing on the brake pedal.

In the event of a failure or malfunction of the

parking brake, secure the vehicle against roll‐

ing using a wheel chock, e.g., when leaving it.

The LED and indicator lamp go out.

The parking brake is released.

After a power failure

Automatic release in cars with

M double-clutch transmission

Putting the parking brake into

operation

1. Switch on the ignition.

Inadvertent operation of the accelerator

pedal

Make sure that the accelerator pedal is not op‐

erated unintentionally; otherwise, the vehicle is

set in motion and there is a risk of an acci‐

dent.◀

2.

Press the reel while stepping on the

brake pedal or transmission position P is

set.

It may take several seconds for the brake to be

put into operation. Any sounds associated with

this are normal.

For automatic release, step on the accelerator

pedal.

The LED and indicator lamp go out.

The indicator lamp in the instrument

cluster goes out as soon as the parking

brake is ready for operation.

The parking brake is automatically released

when you step on the accelerator:

▷

Engine on.

68

Driving

Controls

High beams, headlight flasher

Turn signal, high beams,

headlight flasher

Turn signal

Using turn signals

▷

High beams, arrow 1.

Headlight flasher, arrow 2.

Washer/wiper system

Press the lever beyond the resistance point.

To switch off manually, press the lever to the

resistance point.

Switching the wipers on/off and brief

wipe

Unusually rapid flashing of the indicator lamp

indicates that a turn signal bulb has failed.

Hints

Do not activate wipers if frozen to wind‐

shield

Triple turn signal activation

Press the lever to the resistance point.

The turn signal flashes three times.

The function can be activated or deactivated.

On the Control Display:

Do not switch on the wipers if they are frozen

to the windshield; otherwise, the wiper blades

and the wiper motor may be damaged.◀

Do not activate wipers on dry windshield

Do not use the wipers if the windshield is

dry, as this may damage the wiper blades or

cause them to become worn more quickly.◀

1. "Settings"

2. "Lighting"

3. "Triple turn signal"

Settings are stored for the profile currently in

use.

Switching on

Signaling briefly

Press the lever to the resistance point and hold

it there for as long as you want the turn signal

to flash.

Push wiper lever up.

69

Controls

Driving

The lever automatically returns to its initial po‐

sition when released.

Activating/deactivating

▷

Normal wiper speed: push up once.

The wipers switch to intermittent operation

when the vehicle is stationary.

▷

Fast wiper speed: press up twice or press

once beyond the resistance point.

Wipers change to normal speed when ve‐

hicle comes to standstill.

Press button on the wiper lever.

Switch off and brief wipe

Wiping is started. If the vehicle is equipped

with a rain sensor: LED in wiper lever lights up.

When wipers are frozen to windshield, wiper

operation is deactivated.

During trip interruption with the rain sensor

switched on: if the trip is resumed within ap‐

prox. 15 minutes, the rain sensor is automati‐

cally activated again.

Deactivate the rain sensor in car washes

Push wiper lever down.

Deactivate the rain sensor when passing

through an automatic car wash; otherwise, un‐

intentional wiping can cause damages.◀

The lever automatically returns to its initial po‐

sition when released.

▷

Single wipe: press down once.

To switch off normal wipe: press down

once.

Setting the frequency or sensitivity of

the rain sensor

▷

To switch off fast wipe: press down twice.

Interval mode or rain sensor

The concept

The rain sensor automatically controls the time

between wipes depending on the intensity of

the rainfall. The sensor is located on the wind‐

shield, directly behind the interior rearview mir‐

ror.

Turn the thumbwheel.

70

Driving

Controls

Folding wipers back down

Clean the windshield, headlights

Before switching the ignition on, fold the

wipers back down to the windshield; other‐

wise, the wipers may become damaged when

they are activated.◀

1. Switch on the ignition.

2. Push wiper lever down. Wipers move to

their resting position and are ready again

for operation.

Pull the wiper lever towards you.

The system sprays washer fluid on the wind‐

shield and activates the wipers briefly.

Washer fluid

Hints

In addition, the headlights are cleaned at regu‐

lar intervals when the vehicle's lights are acti‐

vated.

Antifreeze for washer fluid

Antifreeze is flammable and can cause

injury if it is used incorrectly.

Do not use the washer system at freezing

temperatures

Therefore, keep it away from possible sources

of ignition.

Do not use the washers if fluid could freeze

onto the windshield which might impede your

viewing field. Therefore use antifreeze fluid.

Only keep it in the closed original container

and inaccessible to children.

Follow the notes and instructions on the con‐

tainer.

Avoid using the washer when the reservoir is

empty; operation might damage pump.◀

United States: The washer fluid mixture ratio is

regulated by the U.S. EPA and many individual

states; do not exceed the allowable washer

fluid dilution ratios limits that apply. Follow the

usage instructions on the washer fluid con‐

tainer. Use BMW’s Windshield Washer Con‐

centrate or the equivalent.◀

Windshield washer nozzles

The windshield washer nozzles are automati‐

cally heated while the ignition is switched on.

Fold-out position of the wipers

Fold wipers back when you want to change the

blades or with pending low temperatures.

Adding washer fluid

Only add washer fluid when the engine is

cool, and then close the cover completely to

avoid contact between the washer fluid and

hot engine parts.

1. Switch the ignition on and off again.

2. With icy conditions make sure that blades

are not frozen to the windshield.

3. Press the wiper lever up beyond the point

of resistance and hold it for approx. 3 sec‐

onds, until the wiper remains in a nearly

vertical position.

Otherwise, there is a danger of fire and a risk to

personal safety if the fluid is spilled.◀

After the wipers are folded back down, the

wiper system must be reactivated.

71

Controls

Driving

▷

Various drive programs, Drivelogic.

Washer fluid reservoir

Upshifting display, Shift point indicator, re‐

fer to page 94.

▷

Automatic downshifting and protection

from misshifting even in sequential mode.

▷

Launch Control.

Low Speed Assistant.

Selector lever, selector lever positions

At a glance

All washer nozzles are supplied from one res‐

ervoir.

Fill with a mixture of windshield washer con‐

centrate and tap water and – if required – with a

washer antifreeze, according to the manufac‐

turer's recommendations.

Mix the washer fluid before adding to find the

right mixture.

Do not add windshield washer concentrate and

antifreeze undiluted and do not fill with pure

water; this could damage the wiper system.

▷

R: reverse gear.

Do not mix window washer concentrates of dif‐

ferent manufacturers because they can clog

the windshield washer nozzles.

N: neutral.

Center position, forward position.

+: manual upshifting.

-: manual downshifting.

Recommended minimum fill quantity:

0.2 US gal/1 liter.

D/S: reel between drive mode and sequen‐

tial mode.

M double-clutch

Engaging a selector lever position

Press on the brake pedal and pull or push the

selector lever in the corresponding direction.

transmission with Drivelogic

General information

The M double-clutch transmission with Drive‐

logic is an automatic shift transmission with

two clutches and partial transmissions in which

the gears can be changed without interrupting

the tractive force.

As soon as the selector lever is released, it re‐

verts to the center position. In position R, the

selector lever locks.

The engaged selector lever position is dis‐

played in the instrument cluster and on the se‐

lector lever.

The operation is via the selector lever or two

shift paddles on the steering wheel.

If a selector lever position is engaged, the vehi‐

cle may start rolling, after the brake is released,

e.g. on downhill slopes. Thus, drive off immedi‐

ately after releasing the brake.

Functions

▷

Drive mode or Sequential mode.

72

Driving

Controls

Use the Slow Speed Assistant for maneuver‐

ing and during stop-and-go traffic.

Switch to Sequential mode: shift using the

shift paddles or the selector lever, or push the

selector lever in the D/S direction.

Low Speed Assistant

S Sequential mode

Use the shift paddles or the selector lever to

upshift or downshift without letting off the gas.

The Low Speed Assistant gives assistance at

very low speeds. The vehicle moves at walking

speed.

This can also be used for rocking the vehicle in

the snow. To do this, reel between reverse

gear and forward gear without stepping on the

brakes in the process.

▷

Shortly before falling below a gear-de‐

pendent minimum speed, the transmission

is automatically downshifted.

Upshifting or downshifting is done only if

the rpm and vehicle speed are appropriate.

Activating

For example, there is no downshifting if the

engine speed is too high.

1. Engage a driving position.

2. Briefly tap the accelerator pedal.

The vehicle rolls at minimum speed.

▷

Kickdown: the lowest possible gear is se‐

lected by simultaneously operating the

kickdown and the left shift paddle or selec‐

tor lever.

This is possible in 1st and 2nd gear and in re‐

verse gear.

It is also possible to start out in 2nd gear,

e. g. on icy roads.

Overheating

Do not ride the brake; otherwise, the

transmission may overheat.◀

Switch to Drive mode: push selector lever in

D/S direction.

Deactivating

R is Reverse

Apply the brakes until the vehicle comes to a

stop.

Select only when the vehicle is stationary.

It is also possible to rock the vehicle up to

6 mph/10 km/h. To do this, reel between for‐

ward gear and reverse gear without stepping

on the brakes in the process.

Flashing display on the selector lever

of the double clutch transmission

The actually engaged transmission position

can deviate from the selector lever position in

some situations. The display in the selector

lever flashes.

N is Neutral

Use in automatic car washes, e.g. The vehicle

can then roll, refer to page 200.

Observe the display in the instrument cluster,

refer to page 74, in these cases.

P Park

The drive wheels are blocked.

P is engaged automatically:

D Drive mode

In Drive mode, all forward gears are automati‐

cally changed.

▷

After the engine is switched off when the

vehicle is in radio-ready state, refer to

page 63, or when the ignition is switched

off, refer to page 63, and when position R

or D is set.

Kickdown: for maximum acceleration, e. g.

when passing. To do this, depress the acceler‐

ator pedal past the resistance point.

73

Controls

Driving

▷

With the ignition is off, if position N is set.

Using the shift paddles on the steering

wheel

If the safety belt is unbuckled, the driver's

door is opened, and the brake is released

while the vehicle is stationary and position

D or R is set.

Displays in the instrument cluster

Drive mode

▷

Engaged gear together with

a D, arrow 1.

▷

Shift up: pull right shift paddle.

Shift down: pull left shift paddle.

▷

Selected driving program,

Drivelogic, refer to

page 74, arrow 2.

Drivelogic

Various driving programs are available.

Sequential mode

After each switch between Sequential mode

and Drive mode, the last program selected is

an active.

▷

Engaged gear, arrow 1.

Selected driving program,

Drivelogic, refer to

page 74, arrow 2.

Exception: after each engine start, driving pro‐

gram 1 is active in Drive mode.

▷

Gear shift indicator, refer to

page 86

In Drive mode

Choice of three driving programs:

Note

▷

1: efficient driving.

2: relaxed driving.

3: sporty driving.

When the external temperature is very low, the

display may not work. Current driving direction

is recognizable at the engaged selector lever

position.

In Sequential mode

Gear change

Choice of three driving programs:

Shifting in Sequential mode possible.

▷

1: comfortable shifting operations.

2: sporty, fast shifting operations.

A shift in Drive mode causes a reel to Sequen‐

tial mode.

3: maximum shifting speed, Launch Con‐

trol, refer to page 75.

Using the selector lever

▷

To shift up: pull the selector lever rear‐

wards.

▷

To shift down: press the selector lever for‐

ward.

74

Driving

Controls

Risk of an accident

Selecting driving program using

button in center console

Use the settings for DSC in M Drive; oth‐

erwise, driving stability may be impaired, and

there is risk of an accident.◀

Display in the instrument cluster

Selected driving program corre‐

sponds to the number of illumi‐

nated fields.

Press button repeatedly until the de‐

sired driving program is displayed in

the instrument cluster.

Launch Control

The concept

Launch Control enables optimum acceleration

on surfaces with good traction.

Selecting driving program using

M Drive

On the Control Display:

Hints

1. "Settings"

Component wear

2. "M Drive 1" or "M Drive 2"

Do not use Launch Control too often;

otherwise, this may result in premature wear of

components due to the high stress placed on

the vehicle.◀

3.

Select the symbol.

4. "Mode"

5. Turn the controller until the desired setting

is reached and press the controller.

Do not use Launch Control during the break-in,

refer to page 158, period.

▷

"D": drive mode

"S": sequential mode.

Requirements

6. "Shift position"

Launch Control is available when the engine is

warmed up, that is, after uninterrupted driving

of at least 6 miles/10 km.

7. Turn the controller until the desired setting

is reached and press the controller.

8. Selecting another driving program.

To start with Launch Control do not steer the

steering wheel.

When M Drive is active, setting is immedi‐

ately applied.

Activate Launch Control

1. Deactivate Dynamic Stability Control, refer

to page 125.

To activate M Drive with the selected settings,

press the corresponding button on the steer‐

ing wheel:

▷

2. Select Sequential mode with gear 1 and

driving program 3.

▷

3. With the engine running, apply the brake

with the left foot.

75

Controls

Driving

4. While the vehicle is stationary, press the

selector lever forward and hold it.

M Driving Dynamics Control

A flag symbol is displayed in the instru‐

ment cluster.

The concept

The M Driving Dynamics Control affects the

response of the vehicle to accelerator pedal

movements.

5. Fully depress the accelerator pedal.

The starting engine speed adjusts.

6. If necessary, change the starting engine

speed by 500 rpm via cruise control.

Programs

Response behavior options:

7. Release brake. When the selector lever is

released, the vehicle accelerates. Continue

to depress the accelerator pedal.

▷

"Efficient": efficient, comfortable. Minimal

fuel consumption.

Ideal e. g. in city traffic or on snow.

"Sport": sporty, dynamic.

Upshifting occurs automatically as long as

the accelerator pedal is fully depressed.

▷

"Sport Plus": spontaneous, direct. Maxi‐

mum dynamics.

Launch Control is available again only after a

certain distance has been driven.

Selecting a channel

System limits

This transmission has an overheating protec‐

tion mechanism, which protects the clutch

from extreme stress.

Via M Drive

On the Control Display:

▷

Indicator lamp lights up yellow:

transmission too hot.

1. "Settings"

2. "M Drive 1" or "M Drive 2"

Avoid high engine stress and fre‐

quent starts.

3.

Select the symbol.

4. Select the desired channel.

▷

Indicator lamp lights up red: transmission

is overheating.

When M Drive is active, setting is immedi‐

ately applied.

Further driving at a moderate pace is pos‐

sible. At the next opportunity, stop the car,

shut off the engine and allow the transmis‐

sion to cool down.

To activate M Drive with the selected settings,

press the corresponding button on the steer‐

ing wheel:

▷

Avoid fast starts, and on inclines did not accel‐

erate lightly while letting the clutch slip; other‐

wise, the transmission may overheat.

▷

During traffic jams or at very low speeds, use

the Low Speed Assistant, refer to page 73.

76

Driving

Controls

Using the button

Press button repeatedly until the desired

program is displayed in the instrument

cluster.

Display in the instrument cluster

Engine Dynamics Control with selected

program with activated Display of the

system states of the driving dynamics,

refer to page 85.

Manual transmission

Shifting

Shifting into 5th or 6th gear

When shifting into 5th or 6th gear, push

the gearshift lever to the right; otherwise, inad‐

vertent shifting into 3rd or 4th gear could lead

to engine damage.◀

Reverse gear

Select only when the vehicle is stationary.

To overcome the resistance push the selector

lever dynamically to the left and engage the re‐

verse gear.

77

Controls

Displays

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

Overview, instrument cluster

1

2

3

4

Fuel gaugeꢀꢁ82

5

6

7

8

Engine oil temperatureꢀꢁ82

Current fuel consumption

Electronic displaysꢀꢁ78

Reset milesꢀꢁ83

Speedometer

Messages, e.g. Check Control

Tachometerꢀꢁ82

Electronic displays

▷

Selection lists, refer to page 88.

▷

Date, refer to page 83.

External temperature, refer to page 83.

Auto Start/Stop function, refer to page 65.

On-board computer, refer to page 88.

Digital tachometer, refer to page 83.

Energy recovery, refer to page 84.

78

Displays

Controls

▷

Gear display with Drivelogic, refer to

page 84.

Red lights

Safety belt reminder

▷

Miles/trip miles, refer to page 83.

Flashing or illuminated: safety belt on

the driver or passenger side is not

buckled. The safety belt reminder can

also be activated if objects are placed on the

front passenger seat.

Messages, e.g. Check Control, refer to

page 79.

▷

Current fuel consumption, refer to

page 84.

Navigation display, see User's manual for

Navigation, Entertainment and Communi‐

cation.

Make sure that the safety belts are positioned

correctly.

▷

Range, refer to page 84.

Airbag system

Service requirements, refer to page 85.

Speed limit detection, refer to page 87.

Airbag system and belt tensioner are

defective.

System states of driving dynamics, refer to

page 85.

Have the vehicle checked by the serv‐

ice center immediately.

▷

Time, refer to page 83.

Parking brake

Check Control

The parking brake is set.

The concept

For additional information, refer to Release

parking brake, refer to page 68.

The Check Control system monitors functions

in the vehicle and notifies you of malfunctions

in the monitored systems.

Brake system

A Check Control message is displayed as a

combination of indicator or warning lights and

text messages in the instrument cluster and in

the Head-up Display.

Continue to drive moderately.

Have the vehicle checked by the serv‐

ice center immediately.

In addition, an acoustic signal may sound and a

text message may appear on the Control Dis‐

play.

Front-end collision warning

Indicator/warning lights

General information

The indicator and warning lights in the instru‐

ment cluster can light up in a variety of combi‐

nations and colors.

Illuminated: advance warning is issued,

e.g., when there is the impending dan‐

ger of a collision or the distance to the

vehicle ahead is too small.

Increase distance.

Flashing: acute warning of the imminent dan‐

ger of a collision when the vehicle approaches

another vehicle at a relatively high differential

speed.

Several of the lights are checked for proper

functioning and light up temporarily when the

engine is started or the ignition is switched on.

79

Controls

Displays

Intervention by braking or make an evasive ma‐

neuver.

M Dynamic Mode MDM is switched on.

For more information, see M Dynamic

Mode, refer to page 124.

Pedestrian warning

Additional flashing: MDM controls the

drive and brake forces. The vehicle is

stabilized.

Symbol in the instrument cluster.

If a collision with a person detected in this way

is imminent, the symbol lights up and a signal

sounds.

Illuminated: MDM failed. Have the sys‐

tem checked by the service center.

For more information, see M Dynamic

Mode, refer to page 124.

Yellow lights

Anti-lock Braking System ABS

Flat Tire Monitor FTM

Avoid abrupt braking if possible. Brak‐

ing force boost in some cases defec‐

tive. Stop carefully. Take into account

longer brake travel. Have this checked

by the service center immediately.

The Flat Tire Monitor signals a loss of

tire inflation pressure in a tire.

Reduce your speed and stop cau‐

tiously. Avoid sudden braking and steering ma‐

neuvers.

For more information, see Flat Tire Monitor, re‐

fer to page 106.

DSC Dynamic Stability Control

Flashing: DSC controls the drive and

braking forces. The vehicle is stabi‐

lized. Reduce speed and adapt driving

profile to the driving circumstances.

Tire Pressure Monitor TPM

Illuminated: the Tire Pressure Monitor

signals a loss of tire inflation pressure

in a tire.

Illuminated: DSC failed. Have the system

checked by the service center.

Reduce your speed and stop cautiously. Avoid

sudden braking and steering maneuvers.

For additional information, refer to Dynamic

Stability Control DSC, refer to page 124.

Flashing and then continuously illuminated: no

flat tire or loss of tire inflation pressure can be

detected.

DSC Dynamic Stability Control deactivated

DSC Dynamic Stability Control is

switched off.

▷

Interference through systems or devices

with the same radio frequency: after leav‐

ing the area of the interference, the system

automatically becomes active again.

For additional information, refer to Dy‐

namic Stability Control DSC, refer to

page 124.

▷

TPM could not conclude the reset: perform

the reset of the system again.

M Dynamic Mode MDM

A wheel without TPM electronics is fitted:

have the service center check it if needed.

Malfunction: have the system checked by

your service center.

80

Displays

Controls

For more information, see Tire Pressure Moni‐

tor, refer to page 103.

High-beam Assistant

High-beam Assistant is switched on.

High beams are activated and off auto‐

matically as a function of the traffic sit‐

Steering system

uation.

Steering system in some cases defec‐

tive.

For additional information, refer to High-beam

Assistant, refer to page 97.

Have the steering system checked by

the service center.

Cruise control

Engine functions

The system is switched on. It maintains

the speed that was set using the con‐

trol elements on the steering wheel.

Have the vehicle checked by the serv‐

ice center.

For additional information, refer to On-

board Diagnostics socket, refer to page 188.

Blue lights

High beams

Lane departure warning

High beams are activated.

System is switched on and under cer‐

tain circumstances warns if a detected

lane is left without flashing beforehand.

For additional information, refer to High

beams, refer to page 69.

For additional information, refer to Lane depar‐

ture warning, refer to page 116.

General lamps

Check Control

Green lights

At least one Check Control message is

displayed or is stored. The symbol is

shown in the display of the instrument

cluster.

Turn signal

Turn signal on.

Unusually rapid flashing of the indicator

lamp indicates that a turn signal bulb

has failed.

M Drive

M Drive 1 is activated.

For additional information, refer to Turn signal,

refer to page 69.

M Drive 2 is activated.

Parking lights, headlight control

Parking lights or headlights are acti‐

vated.

Text messages

For additional information, refer to

Parking lights/low beams, headlight control, re‐

fer to page 95.

Text messages in combination with a symbol

in the instrument cluster explain a Check Con‐

trol message and the meaning of the indicator

and warning lights.

81

Controls

Displays

They are stored and can be displayed

again later.

Supplementary text messages

Additional information, such as on the cause of

an error or the required action, can be called up

via Check Control.

Displaying stored Check Control

messages

On the Control Display:

With urgent messages the added text will be

automatically displayed on the Control Display.

1. "Vehicle info"

Symbols

2. "Vehicle status"

Depending on the Check Control message, the

following functions can be selected.

3.

"Check Control"

4. Select the text message.

▷

"Owner's Manual"

Display additional information about the

Check Control message in the Integrated

Owner's Manual.

Messages after trip completion

Special messages displayed while driving are

displayed again after the ignition is switched

off.

▷

"Service request"

Contact your service center.

"Roadside Assistance"

Fuel gauge

Contact Roadside Assistance.

Vehicle tilt position may cause

the display to vary.

Hiding Check Control messages

Depending on the equipment

version, the arrow beside the

fuel pump symbol shows which

side of the vehicle the fuel filler flap is on.

Hints on refueling, refer to page 168.

Tachometer

Press the onboard computer button on the

turn signal lever.

Always avoid engine speeds in

the red warning field. In this

range, the fuel supply is inter‐

rupted to protect the engine.

▷

Some Check Control messages are dis‐

played continuously and are not cleared

until the malfunction is eliminated. If sev‐

eral malfunctions occur at once, the mes‐

sages are displayed consecutively.

Engine oil temperature

▷

Cold engine: the pointer is at

the low temperature end.

Drive at moderate engine

and vehicle speeds.

These messages can be faded for approx.

8 seconds. After this time, they are dis‐

played again automatically.

▷

Other Check Control messages are faded

automatically after approx. 20 seconds.

▷

Normal operating tempera‐

ture: the pointer is in the

82

Displays

Controls

middle or in the left half of

the temperature display.

Ice on roads

Even at temperatures above

▷

Hot engine: the pointer is at the high end of

the temperature range. A Check Control

message is also displayed.

+37 ℉/+3 ℃, roads might be icy.

Therefore, drive carefully on bridges and

shaded roads, e.g., to avoid the increased risk

of an accident.◀

Coolant temperature

If the coolant along with the engine becomes

too hot, a Check Control message is displayed.

Time

The time is displayed at the bot‐

tom of the instrument cluster.

Check the coolant level, refer to page 186.

Setting the time and time for‐

mat, refer to page 91.

Odometer and trip odometer

Display

Date

▷

Odometer, arrow 1.

The date is displayed in the

computer.

Trip odometer, arrow 2.

Setting the date and date for‐

mat, refer to page 91.

Show/reset kilometers

Digital tachometer

Press the knob.

Display

▷

When the ignition is

switched off, the time, the

external temperature and

the odometer are displayed.

The current speed is displayed

in the instrument cluster.

▷

When the ignition is switched on, the trip

odometer is reset.

Activate display

1. "Settings"

External temperature

2. "Instrument cluster"

3. "Digital speedometer"

If the indicator drops to

+37 ℉/+3 ℃ or lower, a signal

sounds.

Adjusting the unit

1. "Settings"

A Check Control message is

displayed.

2. "Language/Units"

3. "Dig. speedo:"

There is an increased risk of ice on roads.

4. Select the desired unit.

83

Controls

Displays

Settings are stored for the profile currently in

use.

With navigation system: range with

destination guidance active

If respective equipment is fitted

and destination guidance is ac‐

tive, the remaining range is dis‐

played when the destination is

reached.

Gear display with Drivelogic

Sequential mode

▷

Engaged gear, arrow 1.

Selected driving program,

Drivelogic, refer to page 74,

arrow 2.

Current fuel consumption

Display

Drive mode

Depending on your vehicle's op‐

tional features, the current fuel

consumption can be displayed

in the instrument cluster. Check

whether you are currently driv‐

ing in an efficient and environmentally-friendly

manner.

▷

Engaged gear together with

a D, arrow 1.

Selected driving program,

Drivelogic, refer to page 74,

arrow 2.

Range

Displaying the current fuel

consumption

1. "Settings"

Display

With a low remaining range:

2. "Instrument cluster"

▷

A Check Control message is

displayed briefly.

3. If necessary, "M dynamic driving syst."

The display for the current fuel con‐

sumption is active.

▷

The remaining range is

shown on the on-board co‐

mupter.

Display of the dynamic driving sys‐

tems, refer to page 85.

▷

With a dynamic driving style - e.g., taking

curves aggressively - engine operation

might vary.

The bar display for the current fuel consump‐

tion is displayed in the instrument cluster.

The Check Control message appears continu‐

ously below a range of approx. 30 miles/50 km.

Energy recovery

Refuel promptly

Display

Refuel no later than at a range of

30 miles/50 km or engine operation might fail

and damage might occur.◀

The kinetic energy of the vehicle

is converted to electrical energy

while coasting. The vehicle bat‐

tery is partially charged and fuel

consumption can be reduced.

84

Displays

Controls

Displaying energy recovery

1. "Settings"

Dynamic driving systems

Display

2. "Instrument cluster"

The dynamic driving system

states are displayed in the in‐

strument cluster.

3. If necessary, "M dynamic driving syst."

The display for the energy recovery is

active.

Display of the dynamic driving sys‐

tems, refer to page 85.

Symbols Description

M Engine Dynamics Control, refer

to page 76.

EfficientDynamics display

Displaying Efficient Dynamics

Information on fuel consumption and technol‐

ogy can be displayed while driving.

Dynamic Damping Control, refer to

page 126.

Servotronic, refer to page 126.

1. "Vehicle info"

2. "EfficientDynamics"

Displaying fuel consumption history

Activate display

The average fuel consumption can be dis‐

played within an adjustable time frame.

1. "Settings"

2. "Instrument cluster"

3. If necessary, "M dynamic driving syst."

"Consumption history"

The display for the dynamic driving

systems is active.

Adjusting fuel consumption history

time frame

Display for current consumption, refer

to page 84, and energy recovery, refer to

page 84.

Select the symbol.

Resetting fuel consumption history

1. Open "Options".

2. "Reset consumption history"

Service requirements

Displaying EfficientDynamics info

The current efficiency can be displayed.

"EfficientDynamics info"

The concept

After the ignition is turned on the instrument

cluster briefly displays available driving dis‐

tance or time to the next scheduled mainte‐

nance.

The following systems are displayed:

▷

Auto Start/Stop function.

Energy recovery.

Your service specialist can read the current

service requirements from your remote con‐

trol.

Climate control output.

85

Controls

Displays

3.

"Service required"

Display

Data regarding the service status or legally

mandated vehicle inspections are automati‐

cally transmitted to your service center before

a service due date.

4. "§ Vehicle inspection"

5. "Date:"

6. Adjust the settings.

7. Confirm.

Detailed information on service

requirements

The entered date is stored.

Automatic Service Request

More information on the scope of service re‐

quired can be displayed on the Control Dis‐

play.

Data regarding the service status or legally

mandated vehicle inspections are automati‐

cally transmitted to your service center before

a service due date.

On the Control Display:

1. "Vehicle info"

You can check when your service center was

notified.

2. "Vehicle status"

3.

"Service required"

On the Control Display:

Required maintenance procedures and le‐

gally mandated inspections are displayed.

1. "Vehicle info"

2. "Vehicle status"

3. Open "Options".

4. "Last Service Request"

4. Select an entry to call up detailed informa‐

tion.

Symbols

Sym‐

bols

Description

Gear shift indicator

The concept

No service is currently required.

The system recommends the most fuel effi‐

cient gear for the current driving situation.

The deadline for scheduled mainte‐

nance or a legally mandated inspec‐

tion is approaching.

The gear shift indicator is active in the sequen‐

tial mode of the M double clutch transmission

and for the manual transmission.

Suggestions to shift gear up or down are dis‐

played in the instrument cluster.

The service deadline has already

passed.

On vehicles without a gear shift indicator, the

engaged gear is displayed.

Entering appointment dates

Enter the dates for the required inspections.

Make sure that the vehicle's date and time are

set correctly.

On the Control Display:

1. "Vehicle info"

2. "Vehicle status"

86

Displays

Controls

Displays

At a glance

Camera

Symbol Description

Shift up to fuel efficient gear.

Shift down to fuel efficient gear.

Speed limit detection

The camera is found near the interior rearview

mirror.

The concept

Keep the windshield in the area behind the in‐

terior rearview mirror clean and clear.

Speed limit detection

Speed limit detection uses a symbol in the

shape of a traffic sign to display the currently

detected speed limit. The camera in the area of

the interior rearview mirror detects traffic signs

at the edge of the road as well as variable over‐

head sign posts. Traffic signs with extra sym‐

bols for wet road conditions, etc. are also de‐

tected and compared with the vehicle's

onboard data, such as for the rain sensor, and

will be displayed depending on the situation.

The system takes into account the information

stored in the navigation system and also dis‐

plays speed limits present on routes without

signs.

Switching on/off

On the Control Display:

1. "Settings"

2. "Instrument cluster"

3. "Speed limit information"

If speed limit detection is switched on, it can

be displayed on the info display in the instru‐

ment cluster via the computer.

Display

The following is displayed in the instrument

cluster:

Hints

Personal judgment

Speed limit detection

The system cannot serve as a substitute

for the driver's personal judgment of the traffic

situation.

Current speed limit.

The system assists the driver and does not re‐

place the human eye.◀

Speed limit detection is not

available.

87

Controls

Displays

Speed limit detection can also be displayed in

the Head-up Display.

▷

Turn on voice activation system.

Display

System limits

The system may not be fully functional and

may provide incorrect information in the fol‐

lowing situations:

▷

In heavy fog, rain or snowfall.

When signs are concealed by objects.

When driving very close to the vehicle in

front of you.

▷

When driving toward bright lights.

Depending on your vehicle's optional features,

the list in the instrument cluster can differ from

the illustration shown.

When the windshield behind the interior

rearview mirror is fogged over, dirty or cov‐

ered by a sticker, etc.

▷

In the event of incorrect detection by the

camera.

Activating a list and adjusting the

setting

If the speed limits stored in the navigation

system are incorrect.

In areas not covered by the navigation sys‐

tem.

When roads differ from the navigation,

such as due to changes in road routing.

When passing buses or trucks with a

speed sticker.

▷

If the traffic signs are non-conforming.

On the right side of the steering wheel, turn

the thumbwheel to activate the corresponding

list.

During calibration of the camera immedi‐

ately after vehicle shipment.

Using the thumbwheel, select the desired set‐

ting and confirm it by pushing the thumbwheel.

Selection lists in the

instrument cluster

The concept

On-board computer

Depending on your vehicle's optional features,

the following can be displayed or operated us‐

ing the buttons and the thumbwheel on the

steering wheel as well as the displays in the in‐

strument cluster and the Head-up Display:

Indication in the info display

The information from the com‐

puter is shown in the info display

in the instrument cluster.

▷

Current audio source.

Redial phone feature.

88

Displays

Controls

On the Control Display:

Calling up information on the info

display

1. "Settings"

2. "Instrument cluster"

3. Select the desired displays.

Information in detail

Range

Displays the estimated cruising range available

with the remaining fuel.

It is calculated based on your driving style over

the last 20 miles/30 km.

Press the onboard computer button on the

turn signal lever.

If there is only enough fuel left for less than

45 miles/80 km, the color of the display

changes.

Information is displayed in the info display of

the instrument cluster.

Information at a glance

Average fuel consumption

The average fuel consumption is calculated for

the period while the engine is running.

Repeatedly pressing the button on the turn

signal lever calls up the following information in

the info display:

The average fuel consumption is calculated for

the distance traveled since the last reset by the

on-board comupter.

▷

Range.

Average consumption, fuel.

Average speed.

Average speed

Periods in which the vehicle is parked with the

engine manually stopped are not included in

the calculation of the average speed.

Date.

Speed limit detection.

Not for a multi-functional instrument dis‐

play.

Resetting average values

▷

Time of arrival.

Press and hold the onboard computer button

on the turn signal lever.

When destination guidance is activated in

the navigation system.

Distance to destination

Distance to destination.

The distance remaining to the destination is

displayed if a destination is entered in the navi‐

gation system before the trip is started.

When destination guidance is activated in

the navigation system.

The distance to the destination is adopted au‐

tomatically.

Adjusting the info display

Depending on the vehicle equipment version,

you can select what information from the com‐

puter is to be displayed on the info display of

the instrument cluster.

89

Controls

Displays

3. "Consumpt." or "Speed"

4. "Yes"

Time of arrival

The estimated time of arrival is

displayed if a destination is en‐

tered in the navigation system

before the trip is started.

Sport displays

The time must be correctly set.

The concept

On the Control Display, the current values for

performance and torque can be displayed if

the vehicle is appropriately equipped.

Speed limit detection

Description of the speed limit detection, refer

to page 87, function.

Displaying sport displays on the

Control Display

1. "Vehicle info"

Trip computer

The vehicle features two types of board com‐

puters.

2. "Sport displays"

▷

"Onboard info": the values can be reset as

often as necessary.

▷

"Trip computer": the values provide an

overview of the current trip.

Speed warning

The concept

Displays a speed, when reached, should cause

a warning to be issued.

Resetting the trip computer

On the Control Display:

The warning is repeated if the vehicle speed

drops below the set speed once by at least

3 mph/5 km/h.

1. "Vehicle info"

2. "Trip computer"

3. "Reset": all values are reset.

"Automatically reset": all values are reset

approx. 4 hours after the vehicle came to a

standstill.

Displaying, setting or changing the

speed warning

On the Control Display:

1. "Settings"

2. "Speed"

Display on the Control Display

Display the computer or trip computer on the

Control Display.

3. "Warning at:"

4. Turn the controller until the desired speed

is displayed.

1. "Vehicle info"

2. "Onboard info" or "Trip computer"

5. Press the controller.

Speed warning is stored.

Resetting the fuel consumption or

speed

On the Control Display:

1. "Vehicle info"

2. "Onboard info"

90

Displays

Controls

6. Turn the controller until the desired mi‐

nutes are displayed.

Activating/deactivating the speed

warning

On the Control Display:

7. Press the controller.

The time is stored.

1. "Settings"

2. "Speed"

Setting the time format

1. "Settings"

3. "Warning"

4. Press the controller.

2. "Time/Date"

3. "Format:"

Setting your current speed as the

speed warning

On the Control Display:

4. Select the desired format.

The time format is stored.

1. "Settings"

Automatic time setting

2. "Speed"

Depending on your vehicle's optional features,

the time, date and, if needed, the time zone are

updated automatically.

3. "Select current speed"

4. Press the controller.

The current vehicle speed is stored as the

speed warning.

1. "Settings"

2. "Time/Date"

3. "Auto time set"

Settings on the Control

Display

Date

Setting the date

1. "Settings"

2. "Time/Date"

3. "Date:"

Time

Setting the time zone

1. "Settings"

4. Turn the controller until the desired day is

displayed.

2. "Time/Date"

3. "Time zone:"

5. Press the controller.

4. Select the desired time zone.

The time zone is stored.

6. Make the necessary settings for the month

and year.

The date is stored.

Setting the time

1. "Settings"

2. "Time/Date"

3. "Time:"

Setting the date format

1. "Settings"

2. "Time/Date"

4. Turn the controller until the desired hours

are displayed.

3. "Format:"

4. Select the desired format.

The date format is stored.

5. Press the controller.

91

Controls

Displays

Depending on the light conditions, the bright‐

ness settings may not be clearly visible.

Language

Setting the language

To set the language on the Control Display:

Head-up Display

1. "Settings"

2. "Language/Units"

3. "Language:"

The concept

4. Select the desired language.

Settings are stored for the profile currently in

use.

Setting the voice dialog

Voice dialog for the voice activation system,

refer to page 27.

This system projects important information

into the driver's field of vision, e.g., the speed.

Units of measure

Setting the units of measure

To set the units for fuel consumption, route/

distance and temperature:

The driver can get information without averting

his or her eyes from the road.

Display visibility

1. "Settings"

The visibility of the displays in the Head-up

Display is influenced by the following factors:

2. "Language/Units"

3. Select the desired menu item.

4. Select the desired unit.

▷

Certain sitting positions.

Objects on the cover of the Head-up Dis‐

play.

Settings are stored for the profile currently in

use.

▷

Sunglasses with certain polarization filters.

Wet roads.

Brightness

Unfavorable light conditions.

Setting the brightness

To set the brightness of the Control Display:

If the image is distorted, check the basic set‐

tings.

1. "Settings"

2. "Control display"

3. "Brightness"

4. Turn the controller until the desired bright‐

ness is set.

5. Press the controller.

Settings are stored for the profile currently in

use.

92

Displays

Controls

Select displays in the Head-up Display.

Switching on/off

Selecting displays in the Head-up

Display

On the Control Display:

1. "Settings"

2. "Head-Up Display"

3. "Displayed information"

4. Select the desired displays in the Head-up

Display.

Press button.

Setting the brightness

The brightness is automatically adjusted to the

ambient brightness.

Display

Standard view

The basic setting can be adjusted manually.

On the Control Display:

▷

Speed.

Navigation system.

1. "Settings"

Check Control messages.

Selection list from the instrument cluster.

Driver assistance systems.

2. "Head-Up Display"

3. "Brightness"

4. Turn the controller.

Some of this information is only displayed

briefly as needed.

When the low beams are activated, the bright‐

ness of the Head-up Display can be addition‐

ally influenced using the instrument lighting.

M view

Settings are stored for the profile currently in

use.

Adjusting the height

On the Control Display:

1. "Settings"

2. "Head-Up Display"

3. "Height"

4. Turn the controller.

1

2

3

4

5

6

Current engine speed, highlighted

Shift point indicator

Settings are stored for the profile currently in

use.

Pre-warning field, speed display

Red warning field, speed display

Speed

Setting the rotation

On the Control Display:

Gear display/warning messages

1. "Settings"

2. "Head-Up Display"

Activate M view:

93

Controls

Displays

3. "Rotation"

4. Turn the controller.

Display

Settings are stored for the profile currently in

use.

Special windshield

The windshield is part of the system.

The shape of the windshield makes it possible

to display a precise image.

A film in the windshield prevents double im‐

ages from being displayed.

▷

Current engine speed is displayed in the

tachometer.

Therefore, have the special windshield re‐

placed by a service center only.

Arrow 1: successive yellow illuminated

fields indicate the upcoming upshift mo‐

ment.

▷

Arrow 2: fields are illuminated in red. Do

not wait any further to shift.

Shift point indicator

When the maximum possible speed is

reached, the entire display flashes.

General information

The display is in the Head-up Display.

When the maximum speed is exceeded, the

supply of fuel is interrupted in order to protect

the engine. Speeds in this range must be

avoided.

Shift point indicator in the Head-up

Display

Switching on

Shift lights are only shown in the Head-up Dis‐

play in the M view, refer to page 93.

1. Switch on Head-up Display, refer to

page 93.

2. "Settings"

3. "Head-Up Display"

4. "Displayed information"

5. "M View"

94

Lights

Controls

Lights

If the driver door is opened with the ignition

switched off, the exterior lighting is automati‐

cally switched off at these switch settings.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Parking lights

Position of switch

: the vehicle's lights

light up on all sides, e.g., for parking.

Do not use the parking lights for extended pe‐

riods; otherwise, they might drain the battery

and it would then be impossible to start the en‐

gine.

When parking, it is preferable to switch on the

one-sided roadside parking lights, refer to

page 96.

Overview

Low beams

Position of switch

with the ignition

switched on: the low beams light up.

Welcome lights

When parking the vehicle, leave the switch in

position

or

: the parking and interior

lights light up briefly when the vehicle is un‐

locked.

1

2

Rear fog lights

Depending on the equipment: automatic

headlight control, Adaptive Light Control,

High-beam Assistant, Welcome lights,

Daytime running lights

Activating/deactivating

On the Control Display:

1. "Settings"

3

4

5

Lights off, daytime running lights

2. "Lighting"

Parking lights, daytime running lights

3. "Welcome lights"

Depending on the equipment: low beams,

welcome lights, High-beam Assistant

Settings are stored for the profile currently in

use.

6

Instrument lighting

Headlight courtesy delay feature

The low beams stay lit for a short while after

the radio-ready state is switched off if the

lights are turned off and the headlight flasher is

switched on.

Parking lights/low beams,

headlight control

General information

Position of switch:

,

95

Controls

Lights

2. "Lighting"

Setting the duration

On the Control Display:

3. "Daytime running lamps"

Settings are stored for the profile currently in

use.

1. "Settings"

2. "Lighting"

3. "Pathway lighting:"

4. Set length of time.

Roadside parking lights

Settings are stored for the profile currently in

use.

Automatic headlight control

Position of switch

: the low beams are acti‐

vated and off automatically, e.g., in tunnels, in

twilight or if there is precipitation. The indicator

lamp in the instrument cluster lights up.

The vehicle can be illuminated on one side.

When emerging from a tunnel during the day,

the low beams are not switched off immedi‐

ately but instead only after approx. 2 minutes.

Switching on

With the ignition switched off, press the lever

either up or down past the resistance point for

approx. 2 seconds.

A blue sky with the sun low on the horizon can

cause the lights to be switched on.

Personal responsibility

The automatic headlight control cannot

serve as a substitute for your personal judg‐

ment in determining when to turn the lights on

in response to ambient lighting conditions.

Switch off

Briefly press the lever to the resistance point in

the opposite direction.

E. g. the sensors are unable to detect fog or

hazy weather. To avoid safety risks under

these conditions, you should always switch on

the lights manually.◀

Adaptive Light Control

The concept

Adaptive Light Control is a variable headlight

control system that enables dynamic illumina‐

tion of the road surface.

Daytime running lights

With the ignition switched on, the daytime run‐

ning lights light up in position

. After the ignition is switched off, the park‐

ing lights light up in position

,

or

Depending on the steering angle and other pa‐

rameters, the light from the headlight follows

the course of the road.

.

In tight curves, e.g., on mountainous roads or

when turning, an additional, corner-illuminating

lamp is switched on that lights up the inside of

the curve when the vehicle is moving below a

certain speed.

Activating/deactivating

In some countries, daytime running lights are

mandatory, so it may not be possible to deacti‐

vate the daytime running lights.

On the Control Display:

1. "Settings"

96

Lights

Controls

Activating

Note

Position of switch

switched on.

with the ignition

Personal responsibility

The High-beam Assistant cannot serve

To avoid blinding oncoming traffic, the Adap‐

tive Light Control does not swivel to the driv‐

er's side when the vehicle is at a standstill.

as a substitute for the driver's personal judg‐

ment of when to use the high beams. There‐

fore, manually reel off the high beams in situa‐

tions where required to avoid a safety risk.◀

The turning lights are automatically switched

on depending on the steering angle or the use

of turn signals.

Activating

When driving in reverse, the turning lights may

be automatically switched on regardless of the

steering angle.

Self-leveling headlights

The self-leveling headlights compensate for

acceleration and braking operations in order

not to blind the oncoming traffic and to achieve

optimum illumination of the roadway.

1. Depending on the equipment, turn the light

Malfunction

A Check Control message is displayed.

switch into position

or

.

2. Press button on the turn signal lever, ar‐

row.

Adaptive Light Control is malfunctioning or has

failed. Have the system checked as soon as

possible.

The indicator lamp in the instrument

cluster lights up.

When the low beams are on, the lights are au‐

tomatically brightened or dimmed.

High-beam Assistant

The system responds to light from oncoming

traffic and traffic driving ahead of you, and to

adequate illumination, e.g., in towns and cities.

The concept

When the low beams are activated, this system

automatically switches the high beams on and

off or suppresses the light in the areas that

blind oncoming traffic. The procedure is con‐

trolled by a camera on the front of the interior

rearview mirror. The assistant ensures that the

high beams are activated whenever the traffic

situation allows. The driver can intervene at

any time and switch the high beams non and

off as usual.

The blue indicator lamp in the instru‐

ment cluster lights up when the system

switches on the high beams. Depend‐

ing on the version of the system in the vehicle,

the high beams may not switch off for oncom‐

ing vehicles, but may only be dimmed in the

areas that blind oncoming traffic. In this case,

the blue indicator light will stay on.

97

Controls

Lights

Switching the high beams on and off

manually

Instrument lighting

Adjusting

The parking lights or low beams

must be switched on to adjust

the brightness.

Adjust the brightness with the

thumbwheel.

Interior lights

▷

High beams on, arrow 1.

High beams off/headlight flasher, arrow 2.

General information

The interior lights, footwell lights, access lights

and courtesy lights are controlled automati‐

cally.

The High-beam Assistant can be switched off

when manually adjusting the light. To reacti‐

vate the High-beam Assistant, press the but‐

ton on the turn signal lever.

Thumb wheel for the instrument lighting con‐

trols brightness of some of these features.

System limits

The system is not fully functional in situations

such as the following, and driver intervention

may be necessary:

Overview

▷

In very unfavorable weather conditions,

such as fog or heavy precipitation.

▷

When detecting poorly-lit road users such

as pedestrians, cyclists, horseback riders

and wagons; when driving close to train or

ship traffic; and at animal crossings.

▷

In tight curves, on hilltops or in depres‐

sions, in cross traffic or half-obscured on‐

coming traffic on freeways.

1

2

Interior lights

Reading lamp

In poorly-lit towns and cities and in the

presence of highly reflective signs.

Switching the interior lights on and off

▷

At low speeds.

Press button.

When the windshield behind the interior

rearview mirror is fogged over, dirty or cov‐

ered with stickers, etc.

To reel off permanently: press the button for

approx. 3 seconds.

Switch back on: press button.

98

Lights

Controls

Reading lights

Press button.

Reading lights are located at the front and rear

next to the interior lights.

Bang & Olufsen High End Surround

Sound System

Adjusting speaker lighting

Some speakers in the vehicle are illuminated.

The lighting can be individually set.

1. "Settings"

2. "Lighting"

3. "B&O"

4. Select the desired lighting setting.

▷

"Off": no lighting.

"Reduced": the speakers in the field of

view are faded while driving.

▷

"On": the speakers are always illumi‐

nated.

99

Controls

Safety

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

Airbags

1

2

3

Front airbag, driver

Front airbag, front passenger

Head airbag

4

5

Side airbag

Knee airbags

Front airbags

Side airbags

Front airbags help protect the driver and front

passenger by responding to frontal impacts in

which safety belts alone would not provide ad‐

equate restraint.

In a lateral impact, the side airbag supports the

side of the body in the chest and lap area.

Head airbags

In a lateral impact, the head airbag supports

the head.

100

Safety

Controls

▷

Do not apply adhesive materials to the air‐

bag cover panels, do not cover them or

modify them in any way.

Knee airbag

The knee airbag supports the legs in a frontal

impact.

Never modify either the individual compo‐

nents or the wiring in the airbag system.

This also applies to steering wheel covers,

the dashboard, the seats, the roof pillars

and the sides of the roofliner.◀

Protective action

Airbags are not triggered in every impact situa‐

tion, e.g., in less severe accidents or rear-end

collisions.

Even when you follow all instructions very

closely, injury from contact with the airbags

cannot be ruled out in certain situations.

Information on how to ensure the optimal

protective effect of the airbags

▷

Keep at a distance from the airbags.

The ignition and inflation noise may lead to

short-term and, in most cases, temporary

hearing impairment in sensitive individuals.

Always grasp the steering wheel on the

steering wheel rim, holding your hands at

the 3 o'clock and 9 o'clock positions, to

keep the risk of injury to your hands or

arms as low as possible when the airbag is

triggered.

Malfunction, deactivation and after de‐

ploying the airbags

Do not touch the individual components imme‐

diately after the system has been triggered;

otherwise, you may risk burns.

▷

There should be no person, animals, or ob‐

jects between an airbag and a person.

Only have the airbags checked, repaired or dis‐

mantled and the airbag generator scrapped by

the service center or an authorized repair shop

for handling explosives.

Do not use the cover of the front airbag on

the front passenger side as a storage area.

Dashboard and windshield on the front

passenger side must stay clear - do not at‐

tach adhesive labels or coverings and do

not attach brackets or cables, e. g., for GPS

devices or' mobile phones.

Non-professional attempts to service the sys‐

tem could lead to failure in an emergency or

unintentional activation of the airbag - both

may lead to injury.◀

▷

Make sure that the front passenger is sit‐

ting correctly, i.e., keeps his or her feet and

legs in the footwell; otherwise, leg injuries

might occur when front airbag is activated.

Warnings and information on the airbags are

also found on the sun visors.

Functional readiness of the airbag

system

Do not place slip covers, seat cushions or

other objects on the front passenger seat

that are not approved specifically for seats

with integrated side airbags.

When the ignition is reel on, the warn‐

ing lamp in the instrument cluster lights

up briefly and thereby indicates the op‐

erational readiness of the entire airbag system

and the belt tensioner.

▷

Do not hang pieces of clothing, such as

jackets, over the backrests.

Make sure that occupants keep their heads

away from the side airbag and do not rest

against the head airbag; otherwise, injuries

might occur when airbag is activated.

Airbag system malfunctioning

▷

Warning lamp does not come on when the

ignition is turned on.

▷

Do not remove the airbag system.

Do not remove the steering wheel.

▷

The warning lamp lights up continuously.

101

Controls

Safety

In case of a malfunction have airbag sys‐

tem checked immediately.

▷

Do not attach covers, cushions, ball mats

or other items to the front passenger seat

unless they are specifically recommended

by your vehicle's manufacturer.

In case of a malfunction have airbag system

checked immediately; otherwise, there is a risk

that the system does not function as expected

in case of a severe accident.◀

Do not place any electronic devices on the

passenger seat if a child restraint system is

to be installed on it.

▷

Do not place objects under the seat that

could press against the seat from below.

Automatic deactivation of the front-

seat passenger airbags

The system reads if the front passenger seat is

occupied by measuring the human body's re‐

sistance.

No moisture in or on the seat.

Indicator lamp for the front-seat

passenger airbags

Front, knee and side airbag on the front pas‐

senger's side are either activated or deacti‐

vated.

Leave feet in the footwell

Make sure that the front passenger

keeps his or her feet in the footwell; otherwise,

proper functioning of the front passenger air‐

bag might not be assured.◀

Child restraint fixing system in the front

passenger seat

The indicator lamp for the front-seat passen‐

ger airbags indicates the operating state of the

front-seat passenger airbags.

Before transporting a child on the front pas‐

senger seat, refer to the safety notes and in‐

structions for children on the front passenger

seat, see Children.◀

The lamp indicates whether the airbags are ei‐

ther activated or deactivated.

▷

The indicator lamp lights up

when a child is properly

seated in a child restraint fix‐

ing system or when the seat

is empty. The airbags on the

front passenger side are not

activated.

Malfunction of the automatic

deactivation system

When transporting older children and adults,

the front-seat passenger airbags may be deac‐

tivated in certain sitting positions. In this case,

the indicator lamp for the front-seat passenger

airbags lights up.

▷

The indicator lamp does not light up when,

e.g., a correctly seated person of sufficient

size is detected on the seat. The airbags

on the front passenger side are activated.

In this case, change the sitting position so that

the front-seat passenger airbags are activated

and the indicator lamp goes out.

If it is not possible to activate the airbags, have

the person sit in the rear.

Detected child seats

To enable correct recognition of the occupied

seat cushion

The system generally detects children seated

in a child seat, particularly in child seats re‐

quired by NHTSA when the vehicle was manu‐

102

Safety

Controls

factured. After installing a child seat, make

sure that the indicator lamp for the front-seat

passenger airbags lights up. This indicates

that the child seat has been detected and the

front-seat passenger airbags are not activated.

Tire Pressure Monitor TPM

The concept

The system monitors tire inflation pressure in

the four mounted tires. The system warns you

if there is a significant loss of pressure in one

or more tires. For this purpose, sensors in the

tire valves measure the tire inflation pressure

and tire temperature.

Strength of the driver's and front-seat

passenger airbag

The explosive power that activates driver's/

front passenger's airbags very much depends

on the positions of the driver's/front passeng‐

er's seat.

Hints

Tire damage due to external factors

With a respective message appearing on Con‐

trol Display calibrate the front seats to keep

the accuracy of this function over the long-

term.

Sudden tire damage caused by external

circumstances cannot be recognized in ad‐

vance.◀

With use of the system observe further infor‐

mation found under Tire inflation pressure, re‐

fer to page 172.

Calibrating the front seats

A corresponding message appears on the

Control Display.

Functional requirements

1. Press the reel and move the respective

seat all the way forward.

The system must have been reset with the

correct tire inflation pressure; otherwise, relia‐

ble signaling of tire inflation pressure loss is

not assured.

2. Press the reel forward again. The seat still

moves forward slightly.

3. Readjust the seat to the desired position.

Reset the system after each adjustment of the

tire inflation pressure and after every tire or

wheel change.

The calibration procedure is completed when

the message on the Control Display disap‐

pears.

Always use wheels with TPM electronics to

ensure that the system will operate properly.

If the message continues to be displayed, re‐

peat the calibration.

Status display

If the message does not disappear after a re‐

peat calibration, have the system checked as

soon as possible.

The current status of the Tire Pressure Moni‐

tor TPM can be displayed on the Control Dis‐

play, e.g., whether or not the TPM is active.

Unobstructed area of movement

On the Control Display:

Ensure that the area of movement of the

seats is unobstructed to avoid personal injury

or damage to objects.◀

1. "Vehicle info"

2. "Vehicle status"

3.

"Tire Pressure Monitor (TPM)"

The status is displayed.

103

Controls

Safety

5. Reset tire inflation pressure:"Perform

reset".

Status control display

Tire and system status are indicated by the

color of the wheels and a text message on the

Control Display.

6. Drive away.

The tires are shown in gray and the status is

displayed.

All wheels green

After driving faster than 19 mph/30 km/h for a

short period, the set tire inflation pressures are

accepted as reference values. The reset is

completed automatically while driving.

System is active and will issue a warning rela‐

tive to the tire inflation pressures stored during

the last reset.

After a successfully completed Reset, the

wheels on the Control Display are shown in

green and "Tire Pressure Monitor (TPM)

active" is displayed.

One wheel is yellow

A flat tire or major drop in inflation pressure in

the indicated tire.

You may interrupt this trip at any time. When

you continue the reset resumes automatically.

All wheels are yellow

A flat tire or major drop in inflation pressure in

several tires.

Low tire pressure message

The yellow warning lamp lights up. A

Check Control message is displayed.

Wheels, gray

The system cannot detect a flat tire. Reasons

for this may be:

▷

There is a flat tire or a major loss in

tire inflation pressure.

▷

The system is being reset.

Malfunction.

▷

No reset was performed for the system.

The system therefore issues a warning

based on the tire inflation pressures before

the last reset.

Status information

The status control display additionally shows

the current tire inflation pressures and, de‐

pending on the model, tire temperatures. It

shows the actual values read; they may vary

depending on driving style or weather condi‐

tions.

1. Reduce your speed and stop cautiously.

Avoid sudden braking and steering maneu‐

vers.

2. Identify the damaged wheel. Do so by

checking the tire inflation pressure using

the Mobility System. To correct the tire in‐

flation pressure

Carry out reset

Reset the system after each adjustment of the

tire inflation pressure and after every tire or

wheel change.

3. Repair flat tire with the Mobility System or

replace the damaged wheel.

Required tire inflation pressure check

message

A Check Control message is displayed in the

following situations

On the Control Display and on the vehicle:

1. "Vehicle info"

2. "Vehicle status"

3.

"Perform reset"

▷

The system has detected a wheel change,

but no reset was done.

4. Start the engine - do not drive off.

104

Safety

Controls

▷

Inflation was not carried out according to

specifications.

Declaration according to NHTSA/

FMVSS 138 Tire Pressure Monitoring

System

The tire inflation pressure has fallen below

the level of the last confirmation.

Each tire, including the spare (if provided)

should be checked monthly when cold and in‐

flated to the inflation pressure recommended

by the vehicle manufacturer on the vehicle

placard or tire inflation pressure label. (If your

vehicle has tires of a different size than the size

indicated on the vehicle placard or tire inflation

pressure label, you should determine the

proper tire inflation pressure for those tires.)

As an added safety feature, your vehicle has

been equipped with a tire pressure monitoring

system (TPMS) that illuminates a low tire pres‐

sure telltale when one or more of your tires is

significantly under-inflated. Accordingly, when

the low tire pressure telltale illuminates, you

should stop and check your tires as soon as

possible, and inflate them to the proper pres‐

sure. Driving on a significantly under-inflated

tire causes the tire to overheat and can lead to

tire failure. Under-inflation also reduces fuel ef‐

ficiency and tire tread life, and may affect the

vehicle's handling and stopping ability. Please

note that the TPMS is not a substitute for

proper tire maintenance, and it is the driver's

responsibility to maintain correct tire pressure,

even if under-inflation has not reached the

level to trigger illumination of the TPMS low

tire pressure telltale. Your vehicle has also

been equipped with a TPMS malfunction indi‐

cator to indicate when the system is not oper‐

ating properly. The TPMS malfunction indica‐

tor is combined with the low tire pressure

telltale. When the system detects a malfunc‐

tion, the telltale will flash for approximately one

minute and then remain continuously illumi‐

nated. This sequence will continue upon sub‐

sequent vehicle start-ups as long as the mal‐

function exists. When the malfunction indicator

is illuminated, the system may not be able to

detect or signal low tire pressure as intended.

TPMS malfunctions may occur for a variety of

reasons, including the installation of replace‐

ment or alternate tires or wheels on the vehicle

In this case:

▷

Check the tire pressure and correct as

needed.

▷

Carry out a reset of the system after a tire

change.

System limits

The system does not function properly if a re‐

set has not been carried out, e.g., a flat tire is

reported though tire inflation pressures are

correct.

The tire inflation pressure depends on the

tire's temperature. Driving or exposure to the

sun will increase the tire's temperature, thus

increasing the tire inflation pressure. The tire

inflation pressure is reduced when the tire

temperature falls again. These circumstances

may cause a warning when temperatures fall

very sharply.

Malfunction

The yellow warning lamp flashes and

then lights up continuously. A Check

Control message is displayed. No flat

tire or loss of tire inflation pressure can be de‐

tected.

Display in the following situations:

▷

A wheel without TPM electronics is fitted:

have the service center check it if needed.

Malfunction: have the system checked by

your service center.

TPM was unable to complete the reset.

Reset the system again.

Interference through systems or devices

with the same radio frequency: after leav‐

ing the area of the interference, the system

automatically becomes active again.

105

Controls

Safety

that prevent the TPMS from functioning prop‐

erly. Always check the TPMS malfunction tell‐

tale after replacing one or more tires or wheels

on your vehicle to ensure that the replacement

or alternate tires and wheels allow the TPMS

to continue to function properly.

detect a flat tire. Initialization is started by con‐

firming the tire inflation pressures.

Do not initialize the system when driving with

snow chains.

On the Control Display:

1. "Vehicle info"

2. "Vehicle status"

FTM Flat Tire Monitor

3.

"Perform reset"

4. Start the engine - do not drive off.

5. Start the initialization with "Perform reset".

6. Drive away.

The concept

The system detects tire inflation pressure loss

on the basis of rotation speed differences be‐

tween the individual wheels while driving.

The initialization is completed while driving,

which can be interrupted at any time.

In the event of a tire inflation pressure loss, the

diameter and therefore the rotational speed of

the corresponding wheel changes. This will be

detected and reported as a flat tire.

The initialization automatically continues when

driving resumes.

The system does not measure the actual infla‐

tion pressure in the tires.

Indication of a flat tire

The yellow warning lamp lights up. A

Check Control message is displayed.

Functional requirements

There is a flat tire or a major loss in tire

inflation pressure.

The system must have been initialized when

the tire inflation pressure was correct; other‐

wise, reliable flagging of a flat tire is not as‐

sured. Initialize the system after each correc‐

tion of the tire inflation pressure and after

every tire or wheel change.

1. Reduce your speed and stop cautiously.

Avoid sudden braking and steering maneu‐

vers.

2. Identify the damaged wheel. Do so by

checking the tire inflation pressure using

the Mobility System. If the tire inflation

pressure in all tires is correct, the Flat Tire

Monitor may not have been initialized. In

this case, initialize the system.

Status display

The current status of the Flat Tire Monitor can

be displayed on the Control Display, e.g.,

whether or not the FTM is active.

On the Control Display:

3. Repair flat tire with the Mobility System or

replace the damaged wheel.

1. "Vehicle info"

2. "Vehicle status"

System limits

3.

"Flat Tire Monitor (FTM)"

Sudden tire damage

The status is displayed.

Sudden serious tire damage caused by

external circumstances cannot be recognized

in advance.◀

Initialization

When initializing the once set inflation tire

pressures serve as reference values in order to

106

Safety

Controls

A natural, even tire inflation pressure loss in all

four tires will not be recognized. Therefore,

check the tire inflation pressure regularly.

Be alert

Due to system limitations, warnings may

be not issued at all, or may be issued late or

improperly. Therefore, always be alert and

ready to intervene; otherwise, there is the risk

of an accident.◀

The system could be delayed or malfunction in

the following situations:

▷

When the system has not been initialized.

When driving on a snowy or slippery road

surface.

Tow-starting and towing

For tow-starting or towing, switch off the

Intelligent Safety systems; otherwise malfunc‐

tions of the individual braking systems might

lead to accidents.◀

▷

Sporty driving style: spinning traction

wheels, high lateral acceleration (drifting).

When driving with snow chains.

At a glance

Intelligent Safety

Button in the vehicle

The concept

Intelligent Safety enables central operation of

the driver assistance system.

Depending on how the vehicle is equipped, In‐

telligent Safety consists of one or more sys‐

tems that can help prevent a imminent colli‐

sion. These systems are active automatically

every time the engine is started using the

Start/Stop button:

▷

Front-end collision warning with City Brak‐

ing function, refer to page 108.

Intelligent Safety button

▷

Pedestrian warning, refer to page 110.

Camera

Hints

Personal responsibility

The system does not serve as a substi‐

tute for the driver's personal judgment of the

traffic situation.

Be aware of the traffic situation and the vehi‐

cle's surroundings at all times, otherwise acci‐

dents are still possible despite all warnings.◀

Adapting your speed and driving style

The camera is found near the interior rearview

mirror.

The displays and warnings of the system

do not relieve the driver of the responsibility to

adapt his or her driving speed and style to the

traffic conditions.◀

Keep the windshield in the area behind the in‐

terior rearview mirror clean and clear.

107

Controls

Safety

Switching on/off

Detection range

The Intelligent Safety systems are automati‐

cally active after every departure.

Press button: the systems are turned

off. The LED goes out.

Press button: the systems are turned on. The

LED lights up.

Settings can be made on the Control Display.

It responds to objects if they are detected by

the system.

Front-end collision warning

with City Braking function

Hints

The concept

Personal responsibility

The ystem can help prevent accidents. If an

accident cannot be prevented, the system will

help reduce the collision speed.

The system does not serve as a substi‐

tute for the driver's personal judgment of the

traffic situation.

The system sounds a warning before an immi‐

nent collision and actuates brakes independ‐

ently if needed.

Be aware of the traffic situation and the vehi‐

cle's surroundings at all times, otherwise acci‐

dents are still possible despite all warnings.◀

The automatic braking intervention is done

with limited force and duration.

Adapting your speed and driving style

A camera in the area of the rearview mirror

controls the system.

The displays and warnings of the system

do not relieve the driver of the responsibility to

adapt his or her driving speed and style to the

traffic conditions.◀

The front-end collision warning is available

even if cruise control has been deactivated.

With the vehicle approaching another vehicle

intentionally the collision warning is delayed

avoiding false alarm.

Be alert

Due to system limitations, warnings may

be not issued at all, or may be issued late or

improperly. Therefore, always be alert and

ready to intervene; otherwise, there is the risk

of an accident.◀

General information

The system warns at two levels of an imminent

danger of collision at speeds from approx.

3 mph/5 km/h. Time of warnings may vary with

the current driving situation.

Tow-starting and towing

For tow-starting or towing, switch off the

Intelligent Safety systems; otherwise malfunc‐

tions of the individual braking systems might

lead to accidents.◀

Appropriate braking kicks in at speeds of up to

35 mph/60 km/h.

108

Safety

Controls

At a glance

Setting the warning time

The warning time can be set via iDrive.

Button in the vehicle

1. "Settings"

2. "Frontal Coll. Warning"

3. Activate the desired time on the Control

Display.

The selected time is stored for the profile cur‐

rently in use.

Warning with braking function

Display

Intelligent Safety button

If a collision with a recognized vehicle is immi‐

nent a warning symbol appears in the instru‐

ment cluster and in the Head-Up Display.

Camera

Symbol Measure

The vehicle lights up red: prewarn‐

ing.

Brake and increase distance.

The vehicle flashes red and an

acoustic signal sounds: acute warn‐

ing.

You are requested to intervene by

braking or make an evasive maneu‐

ver.

The camera is found near the interior rearview

mirror.

Keep the windshield in the area behind the in‐

terior rearview mirror clean and clear.

Prewarning

This warning is issued, e.g., when there is the

impending danger of a collision or the distance

to the vehicle ahead is too small.

Switching on/off

Switching on automatically

The system is automatically active after every

driving-off.

The driver must intervene actively when there

is a prewarning.

Acute warning with braking function

Switch off

Warning of the imminent danger of a collision

when the vehicle approaches another object at

a relatively high differential speed.

Press button: the system is switched

off. The LED goes out.

Re-press button: the system is switched on.

The LED lights up.

The driver must intervene actively when there

is an acute warning. If necessary, the driver is

assisted by a minor automatic braking inter‐

vention in a possible risk of collision.

109

Controls

Safety

Acute warnings can also be triggered without

previous prewarning.

▷

In heavy fog, rain, sprayed water or snow‐

fall.

▷

In tight curves.

Braking intervention

If the driving stability control systems are

limited or deactivated, e.g., DSC OFF.

The warning prompts the driver himself/herself

to react. During a warning, the maximum brak‐

ing force is used. Premise for the brake boos‐

ter is sufficiently quick and hard stepping on

the brake pedal. The system can assist with

some braking intervention if there is risk of a

collision. At low speeds vehicles may thus

come to a complete stop.

▷

If, depending on the vehicle equipment

version, the field of view of the camera in

the mirror or the radar sensor is dirty or ob‐

scured.

▷

Up to 10 seconds after the start of the en‐

gine, via the Start/Stop knob.

During calibration of the camera immedi‐

ately after vehicle shipment.

Manual transmission: During a braking inter‐

vention up to a complete stop, the engine may

be shut down.

If there is constant blinding effects be‐

cause of oncoming light, e. g., from the sun

low in the sky.

The braking intervention is executed only if

DSC Dynamic Stability Control is switched on

and M Dynamic mode MDM is not activated.

Warning sensitivity

The braking intervention can be interrupted by

stepping on the accelerator pedal or by ac‐

tively moving the steering wheel.

The more sensitive the warning settings are,

e.g. the warning time, the more warnings are

displayed. However, there may also be an ex‐

cess of false warnings.

Object detection can be restricted. Limitations

of the detection range and functional restric‐

tions are to be considered.

Pedestrian warning

System limits

Depending on how the vehicle is equipped, the

function warns of an imminent collision with

pedestrians during daytime or nighttime.

Detection range

The system's detection potential is limited.

The function is subdivided into the following

systems:

Thus a warning might not be issued or be is‐

sued late.

▷

During daytime: Pedestrian warning with

city braking function, refer to page 110

E. g. the following situations may not be de‐

tected:

▷

At night: Night vision, refer to page 113

▷

Slow moving vehicles when you approach

them at high speed.

▷

Vehicles that suddenly swerve in front of

you, or sharply decelerating vehicles.

Pedestrian warning with city

braking function

▷

Vehicles with an unusual rear appearance.

Two-wheeled vehicles ahead of you.

The concept

The ystem can help prevent accidents with pe‐

destrians.

Functional limitations

The system may not be fully functional in the

following situations:

110

Safety

Controls

The system issues a warning in the city driving

speed area if there is imminent danger of a col‐

lision with pedestrians and includes a braking

function.

Hints

Personal responsibility

The system does not serve as a substi‐

tute for the driver's personal judgment of the

traffic situation.

The camera in the area of the rearview mirror

controls the system.

Be aware of the traffic situation and the vehi‐

cle's surroundings at all times, otherwise acci‐

dents are still possible despite all warnings.◀

General information

In daylight the system warns of possible colli‐

sions with pedestrians at speeds from about

6 mph/10 km/h to about 35 mph/60 km/h

shortly before a collision the system supports

you with a braking intervention.

Adapting your speed and driving style

The displays and warnings of the system

do not relieve the driver of the responsibility to

adapt his or her driving speed and style to the

traffic conditions.◀

Under those circumstances it reacts to people

who are within the detection range of the sys‐

tem.

Be alert

Due to system limitations, warnings may

be not issued at all, or may be issued late or

improperly. Therefore, always be alert and

ready to intervene; otherwise, there is the risk

of an accident.◀

Detection range

Tow-starting and towing

For tow-starting or towing, switch off the

Intelligent Safety systems; otherwise malfunc‐

tions of the individual braking systems might

lead to accidents.◀

The detection area in front of the vehicle is div‐

ided into two areas.

At a glance

▷

Central area, arrow 1, directly in front of the

vehicle.

Button in the vehicle

▷

Expanded area, arrow 2, to the right and

left.

A collision is imminent if pedestrians are lo‐

cated within the central area. A warning is is‐

sued about pedestrians who are located within

the extended area only if they are moving in

the direction of the central area.

Intelligent Safety button

111

Controls

Safety

ter is sufficiently quick and hard stepping on

the brake pedal. The system can assist with

some braking intervention if there is risk of a

collision. At low speeds vehicles may thus

come to a complete stop.

Camera

Manual transmission: During a braking inter‐

vention up to a complete stop, the engine may

be shut down.

The braking intervention is executed only if

DSC Dynamic Stability Control is switched on

and M Dynamic mode MDM is not activated.

The camera is found near the interior rearview

mirror.

The braking intervention can be interrupted by

stepping on the accelerator pedal or by ac‐

tively moving the steering wheel.

Keep the windshield in the area behind the in‐

terior rearview mirror clean and clear.

Object detection can be restricted. Limitations

of the detection range and functional restric‐

tions are to be considered.

Switching on/off

Switching on automatically

The system is automatically active after every

driving-off.

System limits

Detection range

The detection potential of the camera is lim‐

ited.

Switch off

Press button: the systems are turned

off. The LED goes out.

Thus a warning might not be issued or be is‐

sued late.

Press button: the systems are turned on. The

LED lights up.

E. g. the following situations may not be de‐

tected:

▷

Partially covered pedestrians.

Warning with braking function

Display

If a collision with a person detected in this way

is imminent, a warning symbol appears on the

instrument cluster and in the Head-up Display.

Pedestrians that are not detected as such

because of the viewing angle or contour.

▷

Pedestrians outside of the detection range.

Pedestrians having a body size less than

32 in/80 cm.

The red symbol is displayed and a sig‐

nal sounds.

Functional limitations

The system may not be fully functional or may

not be available in the following situations:

Intervene immediately by braking or make an

evasive maneuver.

▷

In heavy fog, rain, sprayed water or snow‐

fall.

Braking intervention

▷

In tight curves.

The warning prompts the driver himself/herself

to react. During a warning, the maximum brak‐

ing force is used. Premise for the brake boos‐

If the driving stability control systems are

deactivated, e.g. DSC OFF.

112

Safety

Controls

▷

If the camera viewing field or the front

windshield are dirty or covered.

radiation emitted by the object. Objects that

are similar in temperature to the environment

or that radiate very little heat are difficult to de‐

tect.

Up to 10 seconds after the start of the en‐

gine, via the Start/Stop knob.

During calibration of the camera immedi‐

ately after vehicle shipment.

For safety reasons, when driving at speeds

above approx. 3 mph/5 km/h and in low ambi‐

ent light, the image is only displayed when the

low beams are activated.

If there is constant blinding effects be‐

cause of oncoming light, e. g., from the sun

low in the sky.

A still image is displayed at regular intervals for

a fraction of a second.

▷

When it is dark outside.

Pedestrian and animal detection

Night Vision with Pedestrian

and Animal Detection

The concept

Night Vision with pedestrian and animal detec‐

tion is a night vision system.

An infrared camera scans the area in front of

the vehicle and issues a warning if it detects

pedestrians and animals on the street. Warm

objects that are similar in shape to human be‐

ings or animals are detected by the system. If

necessary, the heat image can be displayed on

the Control Display.

Object detection and warning only functions in

darkness.

Warm objects that are similar in shape to hu‐

man beings are detected by the system.

In addition, the system also detects animals

above a certain minimum size, e.g., deer.

Heat image

With heat image activated on the Control Dis‐

play:

People detected by the system are displayed

with a slight yellow hue.

Animals detected by the system are displayed

in a darker yellow.

Under good ambient conditions, the object de‐

tection operates within the following distance

ranges:

The image shows the heat radiated by objects

in the field of view of the camera.

▷

Pedestrian detection: up to approx.

330 ft/100 m

Warm objects have a light appearance and

cold objects, a dark appearance.

Detection of large animals: up to approx.

490 ft/150 m

The ability to detect an object depends on the

temperature difference between the object

and the background and on the level of heat

Detection of medium animals: up to ap‐

prox. 230 ft/70 m

113

Controls

Safety

Environmental influences can limit the availa‐

bility of object detection.

The camera is automatically heated when the

external temperatures are low.

If the vehicle systems detect that the vehicle is

located in a residential area, the animal detec‐

tion is temporarily switched off.

The camera lens is automatically cleaned to‐

gether with the headlights.

Switching on/off

Hints

Switching on automatically

Personal responsibility

When it is dark outside, the system is automat‐

ically active after every driving-off.

Night Vision cannot replace the driver's

personal judgment of the visibility conditions

and the traffic situation. The view ahead and

the actual visibility conditions must always be

the basis on which the vehicle speed is ad‐

justed; otherwise, there is a risk to road

safety.◀

Switch off

The system is only switched off until the next

time the engine is started with the Start/Stop

button.

Press button.

Overview

The LED goes out.

Buttons in the vehicle

Switching on heat image additionally

The heat image from the Night Vision camera

can also be displayed on the Control Display.

This function has no effect on object detec‐

tion.

Press button.

The image from the camera is displayed on the

Control Display.

Intelligent Safety button

Adjustments via the iDrive

Switch on/switch off heat image

With heat image switched on:

1. Press the controller.

2. Select brightness or contrast.

Camera

▷

Select the symbol.

3. Turn the controller until the desired setting

is selected.

4. Press the controller.

114

Safety

Controls

The displayed symbol can vary with the people

detected.

Display

Warning of people or animals in

danger

Intervene actively by braking or make an eva‐

sive maneuver.

If a collision with a person or an animal de‐

tected in this way is imminent, a warning sym‐

bol appears on the instrument cluster and in

the Head-up Display.

When animals are detected, an animal

symbol is displayed. The symbol also

shows the side of the road on which

the animal was detected. Intervene actively by

braking or make an evasive maneuver.

Although both the shape and the heat radiation

are analyzed, false warnings cannot be ruled

out.

Acute warning

Warning area in front of the vehicle

The red symbol is displayed and a sig‐

nal sounds.

When animals are detected, an red animal

symbol is displayed with the signal tone.

Red symbol in the instrument cluster.

Intervene immediately by braking or make an

evasive maneuver.

The warning area for the pedestrian warning

consists of two parts:

Display in the Head-up Display

▷

Central area, arrow 1, directly in front of the

vehicle.

The warning is displayed simultane‐

ously in the Head-up Display and on

the instrument cluster. The displayed

symbol can vary with the people detected.

▷

Expanded area, arrow 2, to the right and

left.

When animals are detected, an animal symbol

is displayed.

With animal warnings, no distinction is made

between the central or expanded area.

The entire area moves along with the vehicle in

the direction of the steering angle and changes

with the vehicle speed. As the vehicle speed

increases, the area becomes longer and wider,

e.g.

System limits

Basic limits

System operation is limited in situations such

as the following:

Prewarning

▷

On steep hills, in steep depressions or in

tight curves.

The yellow symbol is displayed when a

person is detected in the central area

immediately in front of the vehicle.

▷

When the camera is dirty or the protective

glass is damaged.

▷

In heavy fog, rain or snowfall.

The yellow symbol is displayed when a person

in the extended area is moving from the right

or left towards the central area.

At very high external temperatures.

115

Controls

Safety

Limits of pedestrian and animal

detection

Hints

Personal responsibility

In some situations, it may occur that pedes‐

trians are detected as animals or animals as

pedestrians.

The system cannot serve as a substitute

for the driver's personal judgment of the

course of the road and the traffic situation.

Small animals are not detected by the object

detection function, even if they are clearly visi‐

ble in the image.

In the event of a warning, do not jerk the steer‐

ing wheel, as you may lose control of the vehi‐

cle.◀

Limited detection:

▷

People or animals who are fully or partially

covered, especially when their heads are

covered.

At a glance

Button in the vehicle

▷

People who are not in an upright position,

e.g., lying down.

Cyclists on unconventional bicycles (e.g.,

recumbent bicycles).

After physical damage to the system, e.g.,

after an accident.

Lane departure warning

The concept

Starting at a specific speed, this system alerts

you when the vehicle on streets with lane

markings is about to leave the lane. This

speed, depending on the country version, is

between 35 mph/55 km/h and

Camera

45 mph/70 km/h.

When switching on the system below this

speed, a message is displayed in the instru‐

ment cluster.

The steering wheel begins vibrating gently in

the event of warnings. The time of the warning

may vary depending on the current driving sit‐

uation.

The camera is found near the interior rearview

mirror.

The system does not provide a warning if the

turn signal is set before leaving the lane.

Keep the windshield in the area behind the in‐

terior rearview mirror clean and clear.

Switching on/off

Press button.

116

Safety

Controls

▷

On: the LED lights up.

Off: the LED goes out.

▷

When the windshield in front of the interior

rearview mirror is fogged over, dirty or cov‐

ered with stickers, etc.

Settings are stored for the profile currently in

use.

During calibration of the camera immedi‐

ately after vehicle shipment.

Display in the instrument cluster

▷

Lines: system is activated.

Active Blind Spot Detection

Arrows: at least one lane marking

was detected and warnings can be

issued.

The concept

Issued warning

If you leave the lane and if a lane marking has

been detected, the steering wheel begins vi‐

brating.

If the turn signal is set before changing the

lane, a warning is not issued.

Two radar sensors below the rear bumper

monitor the area behind and next to the vehicle

at speeds above approx. 30 mph/50 km/h.

End of warning

The warning ends:

▷

Automatically after approx. 3 seconds.

When returning to your own lane.

When braking hard.

The system indicates whether there are vehi‐

cles in the blind spot, arrow 1, or approaching

from behind on the adjacent lane, arrow 2.

When using the turn signal.

The lamp in the exterior mirror housing is dim‐

med.

System limits

The system may not be fully functional in the

following situations:

Before you change lanes after setting the turn

signal, the system issues a warning in the sit‐

uations described above.

▷

In heavy fog, rain or snowfall.

The lamp in the exterior mirror housing flashes

and the steering wheel vibrates.

In the event of missing, worn, poorly visi‐

ble, merging, diverging, or multiple lane

markings such as in construction areas.

Hints

▷

When lane markings are covered in snow,

ice, dirt or water.

Personal responsibility

The system does not serve as a substi‐

tute for the driver's personal judgment of the

traffic situation.

▷

In tight curves or on narrow lanes.

When the lane markings are covered by

objects.

Be aware of the traffic situation and the vehi‐

cle's surroundings at all times, otherwise acci‐

dents are still possible despite all warnings.◀

▷

When driving very close to the vehicle in

front of you.

When driving toward bright lights.

117

Controls

Safety

At a glance

Button in the vehicle

Display

Lamp in the exterior mirror housing

Active Blind Spot Detection

Information stage

The dimmed lamp in the exterior mirror hous‐

ing indicates when there are vehicles in the

blind spot or approaching from behind.

Radar sensors

Warning

If the turn signal is set while a vehicle is in the

critical zone, the steering wheel vibrates briefly

and the lamp in the exterior mirror housing

flashes brightly.

The warning stops when the turn signal is

switched off, or the other vehicle leaves the

critical zone.

The radar sensors are located under the rear

bumper.

System limits

The system may not be fully functional in the

following situations:

Switching on/off

Press button.

▷

When a vehicle is approaching at a speed

much faster than your own.

▷

On: the LED lights up.

Off: the LED goes out.

▷

In heavy fog, rain or snowfall.

In tight curves or on narrow lanes.

Settings are stored for the profile currently in

use.

If the bumper is dirty or iced up, or covered

with stickers.

A Check Control message is displayed when

the system is not fully functional.

For US owners only

The transmitter and receiver units comply with

part 15 of the FCC/Federal Communication

118

Safety

Controls

Commission regulations. Operation is gov‐

erned by the following:

▷

PreCrash

PostCrash

FCC ID:

Attentiveness assistant

The concept

The system can detect increasing lack of alert‐

ness or fatigue of the driver during long, mo‐

notonous journeys, e.g., on highways. In this

situation, it is recommended that the driver

takes a break.

▷

NBG009014A.

Compliance statement:

This device complies with part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

▷

This device may not cause harmful inter‐

ference, and

▷

this device must accept any interference

received, including interference that may

cause undesired operation.

Note

Personal responsibility

Any unauthorized modifications or changes to

these devices could void the user's authority to

operate this equipment.

The system cannot act as a substitute for

the personal assessment of one's physical

state and may not detect an increasing lack of

alertness or fatigue or may not detect it cor‐

rectly. Therefore, make sure that the driver is

rested and alert; otherwise, risks may be de‐

tected too late and an accident be caused as a

result.◀

Brake force display

The concept

Function

The system is activated each time the engine

is started and cannot be switched off.

After travel has begun, the system is trained

about the driver, so that increasing lack of

alertness or fatigue can be detected.

This procedure takes the following criteria into

account:

▷

During normal brake application, the outer

brake lights light up.

▷

Personal driving style, e.g., steering behav‐

ior.

During heavy brake application, the inner

brake lights light up in addition.

▷

Driving conditions, e.g., length of trip.

Starting at approximately 43 mph/70 km/h, the

system is active and can display a recommen‐

dation to take a break.

Active Protection

Break recommendation

General information

The Active Protection safety package consists

of systems that are independent of each other:

If the driver becomes increasingly less alert or

fatigued, a message is displayed in the Control

Display with the recommendation to take a

break.

▷

Attentiveness assistant.

119

Controls

Safety

A recommendation to take a break is displayed

only once during an uninterrupted trip.

Note

Personal responsibility

After a break, another recommendation to take

a break cannot be displayed until after approxi‐

mately 45 minutes.

The system cannot possibly serve as a

substitute for the driver's personal judgment of

the traffic situation. The system may not al‐

ways detect critical situations reliably and in a

timely manner. Adapt speed to traffic situation

and drive alertly; otherwise, a risk to safety may

result.◀

System limits

The function may be limited in the following

situations, for instance, and will either output

an incorrect warning or no warning at all:

▷

When the clock is set incorrectly.

Function

When the vehicle speed is mainly below

about 43 mph/70 km/h.

After the safety belt is buckled, the front belts

are automatically pretensioned once after the

vehicle is driven is away.

▷

With a sporty driving style, such as during

rapid acceleration or when cornering fast.

In critical driving situations, the following indi‐

vidual functions become active as needed:

In active driving situations, such as when

changing lanes frequently.

▷

The front belts are automatically preten‐

sioned.

▷

When the road surface is poor.

In the event of strong side winds.

▷

Automatic closing of the windows.

Automatic closing of the glass sunroof.

PreCrash

Automatic Positioning of the backrest for

the front passenger seat.

The concept

After a critical driving situation without an acci‐

dent, the front belts are loosened again. All

other systems can be restored to the desired

setting.

With this system critical driving situations that

might result in an accident can be detected

above a speed of approx. 20 mph/30 km/h. In

these situations, preventive measures are au‐

tomatically taken to minimize the risk of an ac‐

cident as much as possible.

If the belt tension does not loosen automati‐

cally, stop the vehicle and unbuckle the belt

using the red button in the buckle. Fasten the

belt before continuing on your trip.

Critical driving situations may include:

Emergency stop.

PostCrash

If the vehicle includes the front-end collision

warning or front-end collision warning with

braking feature, impending collisions with vehi‐

cles driving ahead or stopped in front of you

can also be detected within the system's

range.

In the event of an accident, the system can

bring the car to a halt automatically without in‐

tervention by the driver in certain situations.

This can reduce the risk of a further collision

and the consequences thereof.

Depressing the brake pedal can cause the ve‐

hicle to brake harder. This interrupts automatic

braking. Destepping on the gas pedal also in‐

terrupts automatic braking.

120

Safety

Controls

After coming to a halt, the brake is released

automatically. Secure the vehicle against roll‐

ing.

121

Controls

Driving stability control systems

2. Release the foot brake and drive off with‐

Vehicle features and options

out delay.

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

After the foot brake is released, the vehicle is

held in place for approx. 2 seconds.

Depending on the vehicle load, the vehicle may

roll back slightly.

Driving off without delay

After releasing the foot brake, start driv‐

ing without delay, since the drive-off assistant

will not hold the vehicle in place for more than

approx. 2 seconds and the vehicle will begin to

roll back.◀

Antilock Brake System ABS

ABS prevents locking of the wheels during

braking.

M Drive

The vehicle contains its steering power even

during full brake applications, thus increasing

active safety.

The concept

Individual settings can be carried out in two

preassigned configurations for the vehicle.

ABS is operational every time you start the en‐

gine.

When the engine is started, an efficient driving

state is active by default. M Drive is deacti‐

vated.

Brake assistant

At a glance

When you apply the brakes rapidly, this system

automatically produces the greatest possible

braking force boost. It reduces the braking dis‐

tance to a minimum during emergency stop.

This system utilizes all of the benefits provided

by ABS.

Configurations

The configurations are preassigned as follows:

▷

"M Drive 1": relaxed, comfortable driving.

"M Drive 2": sporty, dynamic driving.

Do not reduce the pressure on the brake pedal

for the duration of the emergency stop.

Setting options

Symbol Meaning

Drive-off assistant

Dynamic Stability Control DSC, re‐

This system supports driving off on inclines.

The parking brake is not required.

fer to page 124, and M Dynamic

Mode MDM.

1. Hold the vehicle in place with the foot

brake.

Programs of M Engine Dynamics

Control, refer to page 76.

122

Driving stability control systems

Deactivating

Controls

Symbol Meaning

Programs of Dynamic Damping

Press the corresponding button on the steer‐

ing wheel.

Control, refer to page 126.

Indicator lights

Programs of Servotronic, refer to

page 126.

▷

Indicator lamp comes on: corre‐

sponding M Drive is activated.

Drivelogic, refer to page 74: shift

modes and Drivelogic driving pro‐

grams.

▷

Indicator lamp flashes: M Drive

could not be activated. Antilock

braking system ABS or Dynamic

Stability Control DSC directly regu‐

late the driving stability.

Views of the Head-up Display, refer

to page 92.

Reactivate M Drive if indicator lamp

is no longer flashing.

Configuring M Drive

The preassigned configurations can be individ‐

ually adjusted.

Hints

If M Drive is activated, individual settings can

also be modified outside of M Drive, e. g. using

the buttons in the center console. This deacti‐

vates M Drive.

On the Control Display:

1. "Settings"

2. "M Drive 1" or "M Drive 2"

3. Select the desired setting option.

4. Select the desired channel.

To reactivate all settings made for M Drive on

the Control Display, briefly press one of the fol‐

lowing buttons:

Individual settings are stored for the profile

currently in use.

▷

If M Drive is activated, a change in the setting

on the Control Display is immediately adopted.

▷

To adopt the changed settings in M Drive,

press and hold the corresponding button.

Activating/deactivating M Drive

Activating

Press the corresponding button on the steer‐

ing wheel:

Resetting M Drive

Individual settings can be reset to default val‐

ues.

▷

Activate M Drive 1.

1. "Settings"

▷

Activate M Drive 2.

2. "M Drive 1" or "M Drive 2"

3. "Reset M Drive 1" or "Reset M Drive 2"

4. "Yes"

If DSC OFF or MDM is set in M Drive, a mes‐

sage appears in the instrument cluster. This

message is confirmed by pressing the button

again.

To cancel resetting: "No"

123

Controls

Driving stability control systems

DSC OFF button

DSC Dynamic Stability

Control

Indicator/warning lights

The concept

DSC prevents traction loss in the power

wheels when driving off and accelerating.

The indicator lamp flashes: DSC con‐

trols the drive and braking forces.

The indicator lamp lights up: DSC has

DSC also recognizes unstable vehicle condi‐

tions such as fishtailing or nose-diving. Within

the physical limits DSC helps to keep the vehi‐

cle on a steady course by reducing engine

speed and by applying brakes to the individual

wheels.

failed.

M Dynamic Mode MDM

M Dynamic Mode makes it possible to drive on

a dry roadway with high longitudinal and trans‐

verse acceleration but with limited driving sta‐

bility.

Note

Adjust your driving style to the situation

Only in the absolute limit area does the system

intervene for stabilization by reducing the en‐

gine power and by braking interventions on the

wheels. In this driving condition, additional

steering corrections may be necessary.

An appropriate driving style is always the

responsibility of the driver.

The laws of physics cannot be repealed, not

even with DSC.

Limited stabilizing interventions

Therefore, do not reduce the additional safety

margin by driving in a risky manner.◀

When M Dynamic Mode is activated, sta‐

bilizing interventions are carried out only to a

reduced extent. You must react yourself; oth‐

erwise, there is the risk of an accident.◀

Do not deactivate DSC when driving with

roof load

Do not deactivate Dynamic Stability Control

DSC when driving with roof load, e.g. roof-

mounted luggage rack.

To increase vehicle stability, activate DSC

again as soon as possible.

Otherwise, driving safety is not given in driv‐

ing-critical situation due to the elevated center

of gravity.◀

Activating MDM

Press button briefly.

The MDM and DSC OFF indicator lights

on the instrument cluster light up.

Overview

Button in the vehicle

Deactivating MDM

Press button.

The MDM and DSC OFF indicator lights

go out.

124

Driving stability control systems

Controls

Via M Drive

Deactivating DSC: DSC OFF

On the Control Display:

When DSC is deactivated, driving stability is

reduced during acceleration and when driving

in curves.

1. "Settings"

2. "M Drive 1" or "M Drive 2"

To increase vehicle stability, activate DSC

again as soon as possible.

3.

Select the symbol.

4. "MDM"

Deactivating DSC

To open M Drive with the selected settings,

press the corresponding button on the steer‐

ing wheel:

Press and hold this button but not longer

than approx. 10 seconds, until the indica‐

tor lamp for DSC OFF lights up in the instru‐

ment cluster and displays DSC OFF.

▷

The DSC system is switched off.

▷

A message appears in the instrument cluster.

This message is confirmed by pressing the

button again.

Activating DSC

Press button.

DSC OFF and the DSC OFF indicator

lamp go out.

Deactivating MDM

Press the appropriate button 1 or button 2 on

the steering wheel again.

Via M Drive

M Dynamic Mode and the settings selected

under M Drive are deactivated.

On the Control Display:

1. "Settings"

2. "M Drive 1" or "M Drive 2"

Indicator/warning lights

3.

Select the symbol.

Indicator lights light up:

4. "DSC OFF"

M Dynamic Mode is activated.

To open M Drive with the selected settings,

press the corresponding button on the steer‐

ing wheel:

▷

DSC indicator lamp also flashes:

M Dynamic Mode controls the drive

forces and brake forces.

▷

Indicator lights light up:

A message appears in the instrument cluster.

This message is confirmed by pressing the

button again.

M Dynamic Mode or DSC has failed.

Indicator/warning lights

When DSC is deactivated, DSC OFF is dis‐

played in the instrument cluster.

125

Controls

Driving stability control systems

The indicator lamp lights up: DSC is

deactivated.

When M Drive is active, setting is immedi‐

ately applied.

To activate M Drive with the selected settings,

press the corresponding button on the steer‐

ing wheel:

Active M differential

▷

The concept

▷

The active M differential assures continuously

variable locking of the rear axle differential de‐

pending on the driving situation. This prevents

individual rear wheels from spinning even

when DSC is switched off and in M Dynamic

Mode, so that optimum traction is always as‐

sured in all driving situations.

Using the button

The driver is responsible adapting his or her

driving behavior to the situation.

Dynamic Damping Control

The concept

Press button repeatedly until the desired

program is displayed in the instrument

cluster.

This system reduces undesirable vehicle mo‐

tion when using a dynamic driving style or trav‐

eling on uneven road surfaces.

The system enhances driving dynamics and

comfort fitting road surface and driving style.

Display in the instrument cluster

Dynamic Damping Control with se‐

lected program with activated display

of the system states of the driving dy‐

namics, refer to page 85.

Programs

Setting options for calibrating the shock ab‐

sorbers:

▷

"Comfort": comfort-oriented.

"Sport": balanced out.

Servotronic

"Sport Plus": consistently sporty.

The concept

Selecting a channel

The Servotronic varies the steering force re‐

quired to turn the wheels in accordance with

the vehicle speed. At low speeds, the steering

force is strongly supported, i. e. during steer‐

ing, low force is required. As the speed in‐

creases, the assistance of the steering force is

reduced.

Via M Drive

On the Control Display:

1. "Settings"

2. "M Drive 1" or "M Drive 2"

3.

Select the symbol.

Furthermore, the steering force adapts accord‐

ing to the driving program, so that a direct,

4. Select the desired channel.

126

Driving stability control systems

Controls

sporty feel and/or comfortable steering is con‐

veyed.

Display in the instrument cluster

Servotronic with selected program with

activated display of the System states

of the driving dynamics, refer to

page 85.

Programs

Steering force setting options:

▷

"Comfort": low.

"Sport": medium.

"Sport Plus": high.

Selecting a channel

Via M Drive

On the Control Display:

1. "Settings"

2. "M Drive 1" or "M Drive 2"

3.

Select the symbol.

4. Select the desired channel.

When M Drive is active, setting is immedi‐

ately applied.

To activate M Drive with the selected settings,

press the corresponding button on the steer‐

ing wheel:

▷

Using the button

Press button repeatedly until the desired

program is displayed in the instrument

cluster.

127

Controls

Driving comfort

Controls

Overview

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Press but‐

ton

Function

Cruise control on/off, interrupt,

refer to page 128

Store/maintain speed, refer to

page 129

Resume speed, refer to

page 129

Cruise control

rocker switch:

The concept

Maintain, store, change speed,

refer to page 129

The system maintains a preset speed via the

buttons on the steering wheel. The system

brakes on downhill gradients if engine braking

is insufficient.

Buttons are arranged according to vehicle's

series, optional features and country specifica‐

tions.

General information

Depending on the driving settings, the features

of the cruise control can change in certain

areas.

Switching on

Press button on the steering wheel.

Hints

The marking in the speedometer is set to the

current speed.

Unfavorable conditions

The cruise control can be used.

Do not use the system if unfavorable

conditions make it impossible to drive at a con‐

stant speed, e.g.:

Switch off

Deactivated or interrupted system

▷

On winding roads.

In heavy traffic.

With deactivated or interrupted system

use your brakes, steering and moves as usual

to avoid the chance of an accident.◀

On slippery roads, in fog, snow or rain, or

on a loose road surface.

Otherwise, you could lose control of the vehi‐

cle and cause an accident.◀

Press button on the steering wheel.

▷

If active: press twice.

If interrupted: press once.

128

Driving comfort

Controls

The displays go out. The stored desired speed

is deleted.

This is displayed, refer to page 129, in the

speedometer and briefly in the instrument

cluster.

Interrupting

When cruise control is maintained or stored,

DSC Dynamic Stability Control will be turned

on if needed.

When active, press the button.

The system is automatically interrupted if:

Changing the speed

▷

The brakes are applied.

Press the rocker switch up or down repeatedly

until the desired speed is set.

The clutch pedal is depressed for a few

seconds or released while a gear is not en‐

gaged.

If active, the displayed speed is stored and the

vehicle reaches the stored speed when the

road is clear.

▷

Selector lever position D is disengaged.

MDM is activated or DSC is deactivated.

DSC is actively controlling stability.

▷

Each time the rocker switch is pressed to

the point of resistance, the desired speed

increases or decreases by approx.

1 mph/1 km/h.

Maintaining, storing, and changing the

speed

▷

Each time the rocker switch is pressed

past the point of resistance, the desired

speed increases or decreases by a maxi‐

mum of 5 mph/10 km/h.

Hints

Adjusting the desired speed

The maximum speed that can be set de‐

pends on the vehicle.

Modify desired speed to road conditions

and be ready to brake at all times; otherwise,

there is the risk of an accident.◀

▷

Pressing the rocker switch to the resist‐

ance point and holding it accelerates or de‐

celerates the vehicle without requiring

pressure on the accelerator pedal.

Maintaining/storing the speed

Press button.

Or:

After the rocker switch is released, the ve‐

hicle maintains its final speed. Pressing the

switch beyond the resistance point causes

the vehicle to accelerate more rapidly.

Resuming the desired speed

Press button.

The stored speed is reached and maintained.

Displays in the instrument cluster

Indicator lamp

Press the rocker switch while the system is in‐

terrupted.

Depending on how the vehicle is equip‐

ped, the indicator lamp in the instru‐

When the system is switched on, the current

speed is maintained and stored as the desired

speed.

129

Controls

Driving comfort

ment cluster indicates whether the system is

switched on.

An acoustic warning is first given:

▷

By the front sensors and the two rear cor‐

ner sensors at approx. 24 in/60 cm.

Desired speed

▷

By the rear middle sensors at approx.

5 ft/1.50 m.

▷

The marking lights up green:

the system is active.

To ensure full functionality:

▷

Do not cover sensors, e.g., with stickers,

bicycle racks.

▷

The marking lights up or‐

ange: the system has been

interrupted.

▷

Keep the sensors clean and free of ice.

▷

The marking does not light up: the system

is switched off.

When using high-pressure washers, do not

spray the sensors for long periods and

maintain a distance of at least 12 in/30 cm.

Brief status display

Hints

Selected desired speed.

Personal responsibility

Even an active system does not relieve

the driver from personal responsibility while

driving.

If --- appears briefly on the display for Check

Control messages, it is possible that the sys‐

tem requirements are currently not ready for

operations.

Technically the system has its limits, it cannot

independently react to all traffic situations.

Monitor your driving, be on the alert, observe

the vehicle surroundings and other traffic and

react when needed - risk of accident.◀

Displays in the Head-up Display

Some system information can also be dis‐

played in the Head-up Display.

Avoid driving fast with PDC

Avoid approaching an object too fast.

PDC Park Distance Control

Avoid driving off fast while PDC is not yet ac‐

tive.

The concept

For technical reasons, the system may other‐

wise be too late in issuing a warning.◀

PDC is a support when parking. When you

slowly approach an object in the rear - or also

in the front of the vehicle if the feature is availa‐

ble - then the object is reported through:

▷

Signal tones.

Visual display.

General information

Ultrasound sensors in the bumpers measure

the distances from objects.

The maneuvering range, depending on the ob‐

stacle and environmental conditions, is approx.

6 ft/2 m.

130

Driving comfort

Controls

The shorter the distance to the object, the

shorter the intervals.

Overview

With front PDC: button in vehicle

If the distance to a detected object is less than

approx. 10 in/25 cm, a continuous tone is

sounded.

With front PDC: if objects are located both in

front of and behind the vehicle, an alternating

continuous signal is sounded.

An interval tone is interrupted with the appro‐

priate equipment after about 3 seconds:

▷

If the vehicle stops in front of an object that

is detected by only one of the corner sen‐

sors.

PDC Park Distance Control

▷

If moving parallel to a wall.

Switching on/off

Volume

The volume of the PDC signal tone can be ad‐

justed similar to the sound and volume set‐

tings of the radio.

Switching on automatically

With the engine running, engage lever in posi‐

tion P R.

Settings are stored for the profile currently in

use.

Automatic deactivation during forward

travel

The system switches off when a certain driving

distance or speed is exceeded.

Visual warning

The approach of the vehicle to an object can

be shown on the Control Display. Objects that

are farther away are already displayed on the

Control Display before a signal sounds.

Switch the system back on if needed.

With front PDC: switching on/off

manually

A display appears as soon as Park Distance

Control (PDC) is activated.

Press button.

The range of the sensors is represented in the

colors green, yellow and red.

▷

On: the LED lights up.

Off: the LED goes out.

When the image of the rearview camera is dis‐

played, the reel can be made to PDC:

"Rear view camera"

Display

System limits

Signal tones

When approaching an object, an intermittent

sound indicates the position of the object. E. g.

if an object is detected to the left rear of the

vehicle, a signal tone sounds from the left rear

speaker.

Limits of ultrasonic measurement

Ultrasonic measuring might not function under

the following circumstances:

▷

For small children and animals.

131

Controls

Driving comfort

▷

For persons with certain clothing, e.g.

coats.

▷

Due to other ultrasound sources, e.g.,

sweeping machines, high pressure steam

cleaners or neon lights.

With external interference of the ultra‐

sound, e.g. from passing vehicles or loud

machines.

Malfunction

A Check Control message is displayed.

▷

When sensors are dirty, iced over, dam‐

aged or out of position.

The range of the sensors is shown as a shaded

area on the Control Display.

Under certain weather conditions such as

high relative humidity, rain, snowfall, ex‐

treme heat or strong wind.

PDC has failed. Have the system checked.

To ensure full functionality:

▷

With tow bars and trailer couplings of other

vehicles.

▷

Keep the sensors clean and free of ice.

dimmedDo not put any stickers on sen‐

sors.

▷

With thin or wedge-shaped objects.

With moving objects.

▷

When using high-pressure washers, do not

spray the sensors for long periods and

maintain a distance of at least 12 in/30 cm.

With elevated, protruding objects such as

ledges or cargo.

▷

With objects with corners and sharp edges.

With objects with a fine surface structure

such as fences.

Surround View

▷

For objects with porous surfaces.

The concept

Low objects already displayed, e.g., curbs, can

move into the blind area of the sensors before

or after a continuous tone sounds.

Surround View comprises various camera as‐

sistance systems that help the driver when

parking, maneuvering, and at complex exits

and intersections.

False warnings

▷

Rearview camera, refer to page 132

Side View, refer to page 135.

Top View, refer to page 136.

PDC may issue a warning under the following

conditions even though there is no obstacle

within the detection range:

▷

In heavy rain.

When sensors are very dirty or covered

with ice.

Rearview camera

▷

When sensors are covered in snow.

On rough road surfaces.

The concept

The rearview camera provides assistance in

parking and maneuvering backwards. The area

behind the vehicle is shown on the Control

Display.

On uneven surfaces, such as speed

bumps.

▷

In large buildings with right angles and

smooth walls, e.g., in underground ga‐

rages.

▷

In automatic car washes.

Through heavy pollution.

132

Driving comfort

Controls

Hints

Switching on/off

Check the traffic situation as well

Switching on automatically

With the engine running, engage lever in posi‐

tion P R.

Check the traffic situation around the ve‐

hicle with your own eyes. Otherwise, an acci‐

dent could result from road users or objects

that are not lidtured by the camera.◀

The rearview camera image is displayed if the

system was switched on via the iDrive.

At a glance

Automatic deactivation during forward

travel

The system switches off when a certain driving

distance or speed is exceeded.

Button in the vehicle

Switch the system back on if needed.

Switching on/off manually

Press button.

▷

On: the LED lights up.

Off: the LED goes out.

Rearview camera

The PDC is shown on the Control Display.

Switching the view via iDrive

With PDC activated or Top View switched on:

"Rear view camera"

Camera

The rearview camera image is displayed.

Display on the Control Display

Functional requirement

▷

The rearview camera is switched on.

The trunk lid is fully closed.

The camera lens is located under the BMW

emblem of the tail gate. The image quality may

be impaired by dirt. The camera calibrates it‐

self regularly after the system has been

switched off. This is why the emblem on the

tailgate remains open after the system has

been deactivated and while driving. The em‐

blem closes automatically as soon as calibra‐

tion is complete.

Activating assistance functions

More than one assistance function can be ac‐

tive at the same time.

▷

Parking aid lines

"Parking aid lines"

Lanes and turning radius are indicated.

Obstacle marking

▷

Clean the camera lens, refer to page 203.

"Obstacle marking"

Spatially-shaped markings are displayed.

133

Controls

Driving comfort

Pathway lines

Obstacle marking

Obstacle markings can be faded into the image

of the rearview camera.

▷

Pathway lines can be superimposed on the

image of the rearview camera.

Their colored margins match the markings of

the PDC. This simplifies estimation of the dis‐

tance to the object shown.

They help you to estimate how much

space is needed when parking and maneu‐

vering on level pavement.

▷

They are dependent on the current steer‐

ing angle and are continuously adjusted to

the steering wheel movements.

Parking using pathway and turning

radius lines

1. Position the vehicle so that the turning ra‐

dius lines lead to within the limits of the

parking space.

Turning circle lines

▷

Turning circle lines can only be superim‐

posed on the rearview camera image to‐

gether with pathway lines.

2. Turn the steering wheel to the point where

the pathway line covers the corresponding

turning radius line.

▷

They show the course of the smallest pos‐

sible turning radius on a level road.

Only one turning radius line is displayed af‐

ter the steering wheel is turned past a cer‐

tain angle.

134

Driving comfort

Controls

Display settings

Hints

The images from both cameras are shown si‐

multaneously on the Control Display.

Brightness

With the rearview camera switched on:

Check the traffic situation as well

1.

Select the symbol.

Check the traffic situation around the ve‐

hicle on blind driveways and intersections with

your own eyes. Otherwise, an accident could

result from road users or objects located out‐

side the picture area of the Side View cam‐

eras.◀

2. Turn the controller until the desired setting

is reached, and press the controller.

Contrast

With the rearview camera switched on:

1.

Select the symbol.

At a glance

2. Turn the controller until the desired setting

is reached, and press the controller.

Button in the vehicle

System limits

Detection of objects

Very low obstacles as well as high, protruding

objects such as ledges may not be detected by

the system.

Assistance functions also take into account

data of the PDC.

Follow instructions in the PDC chapter, refer to

page 130.

Side View

The objects displayed on the Control Display

under certain circumstances are closer than

they appear. Do not estimate the distance from

the objects on the display.

Cameras

Side View

The concept

Side View provides an early look at cross traffic

at blind driveways and intersections. Road

users concealed by obstacles to the left and

right of the vehicle can only be detected rela‐

tively late from the driver's seat. To improve

visibility, two cameras in the front of the vehi‐

cle record the traffic situation on each side.

Two cameras integrated in the bumpers cap‐

ture the image.

The two camera lenses are located on the

sides of the bumper.

The image quality may be impaired by dirt.

Clean the camera lenses, refer to page 203.

135

Controls

Driving comfort

Switching on/off

System limits

The cameras lidture a maximum range of

330 ft/100 m.

Switching on/off manually

Press button.

Top View

Automatic deactivation during forward

travel

The concept

The system switches off when a certain driving

distance or speed is exceeded.

Top View provides assistance in parking and

maneuvering. The area around the doors and

the road area around the vehicle are shown on

the Control Display for this purpose.

Switch the system back on if needed.

Display

General information

The traffic area to the left and right is displayed

on the Control Display.

The image is lidtured by two cameras

integrated in the exterior mirrors and by the

rearview camera.

The range is at least 7 ft/2 m to the side and

rear.

In this way, obstacles up to the height of the

exterior mirrors are detected early.

Hints

Check the traffic situation as well

Guidelines at the bottom of the image show

the position of the front of the vehicle.

Check the traffic situation around the ve‐

hicle with your own eyes. Otherwise, an acci‐

dent could result from road users or objects

that are not lidtured by the camera.◀

Brightness

With the Side View switched on:

Overview

1.

"Brightness"

Button in the vehicle

2. Turn the controller until the desired setting

is reached, and press the controller.

Contrast

With the Side View switched on:

1.

"Contrast"

2. Turn the controller until the desired setting

is reached, and press the controller.

Top View

136

Driving comfort

Controls

When the distance to an object is small, a red

bar is shown in front of the vehicle, as it is in

the PDC display.

Cameras

The lenses of the Top View camera are located

at the bottom in the mirror housings. The im‐

age quality may be impaired by dirt.

The display appears as soon as Top View is

activated.

Clean the camera lenses, refer to page 203.

When the image of the rearview camera is dis‐

played, it is possible to reel to top view:

Switching on/off

"Rear view camera"

Switching on automatically

With the engine running, engage lever in posi‐

tion P R.

Brightness

With Top View switched on:

The Top View and PDC images are displayed if

the system is switched on via iDrive.

1.

Select the symbol.

2. Turn the controller until the desired setting

is reached, and press the controller.

Automatic deactivation during forward

travel

The system switches off when a certain driving

distance or speed is exceeded.

Contrast

With Top View switched on:

Switch the system back on if needed.

1.

Select the symbol.

2. Turn the controller until the desired setting

is reached, and press the controller.

Switching on/off manually

Press button.

Displaying the turning radius and

pathway lines

▷

On: the LED lights up.

Off: the LED goes out.

▷

The static, red turning radius line shows

the space needed to the side of the vehicle

when the steering wheel is turned all the

way.

Top View is displayed.

Display

▷

The variable, green pathway line assists

you in assessing the amount of space ac‐

tually needed to the side of the vehicle.

Visual warning

The approach of the vehicle to an object can

be shown on the Control Display.

The lane line depends on the engaged

gear and the current steering angle. The

137

Controls

Driving comfort

track line is continuously adjusted for the

steering wheel movement.

"Parking aid lines"

Turning circle and pathway lines are displayed.

System limits

Top View cannot be used in the following sit‐

uations:

▷

With a door open.

With the trunk lid open.

With an exterior mirror folded in.

In poor light.

A Check Control message is displayed in some

of these situations.

138

Climate control

Controls

Climate control

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

Automatic climate control

1

2

3

4

5

6

7

8

9

Air distribution, left

11 Air distribution, right

Temperature, left

12 Seat heating, rightꢀꢁ51

13 Active seat ventilation, rightꢀꢁ51

AUTO program, left

Air flow, AUTO intensity, left, residual heat

Remove ice and condensation

Maximum cooling

14 Automatic recirculated-air control/recircu‐

lated-air mode

15 Cooling function

16 Rear window defroster

17 SYNC program

Display

Air flow, AUTO intensity, right

AUTO program, right

18 Active seat ventilation, leftꢀꢁ51

19 Seat heating, leftꢀꢁ51

10 Temperature, right

139

Controls

Climate control

Hints

AUTO program

Sufficient ventilation

Press button.

Air flow, air distribution and tempera‐

ture are controlled automatically.

When remaining in the vehicle for an ex‐

tended period of time, ensure sufficient exter‐

nal ventilation. Do not continuously use recir‐

culated-air mode; otherwise the air quality in

the interior continuously deteriorates and win‐

dow condensation increases.◀

Depending on the selected temperature,

AUTO intensity program and outside influen‐

ces, the air is directed to the windshield, side

windows, upper body, and into the footwell.

The cooling function, refer to page 141, is

switched on automatically with the AUTO pro‐

gram.

Climate control functions in detail

Manual air distribution

At the same time, a condensation sensor con‐

trols the program so as to prevent window

condensation as much as possible.

Press button repeatedly to select a

program:

▷

Upper body region.

Intensity of the AUTO program

Upper body region and footwell.

Footwell.

With the AUTO program activated, the auto‐

matic intensity control can be changed.

Windows and footwell.

Press the left or right side of the but‐

ton: decrease or increase the inten‐

sity.

Windows, upper body region, and footwell.

Windows: driver's side only.

Windows and upper body region.

The selected intensity is shown on the display

of the automatic climate control.

If the windows are fogged over, press the

AUTO button on the driver's side to utilize the

condensation sensor.

Air flow, manual

To manually adjust air flow turn off AUTO pro‐

gram first.

Temperature

Turn the ring to set the desired

temperature.

Press the left or right side of the but‐

ton: decrease or increase air flow.

The selected air flow is shown on the display of

the automatic climate control.

The automatic climate control achieves this

temperature as quickly as possible, if needed

by using the maximum cooling or heating li‐

dacity, and then keeps it constant.

The air flow of the automatic climate control

may be reduced automatically to save battery

power.

Do not rapidly switch between different tem‐

perature settings. Otherwise, the automatic cli‐

mate control will not have sufficient time to ad‐

just the set temperature.

Defrosts windows and removes

condensation

Press button.

140

Climate control

Controls

Ice and condensation are quickly removed

from the windshield and the front side win‐

dows.

button on the driver's side to utilize the con‐

densation sensor. Make sure that air can flow

to the windshield.

For this purpose, point the side vents onto the

side windows as needed.

Sufficient ventilation

When remaining in the vehicle for an ex‐

tended period of time, ensure sufficient exter‐

nal ventilation. Do not continuously use recir‐

culated-air mode; otherwise the air quality in

the interior continuously deteriorates and win‐

dow condensation increases.◀

Adjust air flow with the program active.

If the windows are fogged over, you can also

switch on the cooling function or press the

AUTO button to utilize the condensation sen‐

sor.

Cooling function

Maximum cooling

The car's interior can only be cooled with the

engine running.

Press button.

The system is set to the lowest tem‐

perature, optimum air flow and air circulation

mode.

Press button.

The air will be cooled and dehumidi‐

fied and, depending on the temperature set‐

ting, warmed again.

Air flows out of the vents to the upper body re‐

gion. The vents need to be open for this.

Depending on the weather, the windshield and

side windows may fog up briefly when the en‐

gine is started.

The function is available above an external

temperature of approx. 32 ℉/0 ℃ and with the

engine running is indicated.

The cooling function is switched on automati‐

cally with the AUTO program.

Adjust air flow with the program active.

When using the automatic climate control,

condensation water, refer to page 161, devel‐

ops that exits underneath the vehicle.

Automatic recirculated-air control/

recirculated-air mode

You may respond to unpleasant odors or pollu‐

tants in the immediate environment by tempo‐

rarily suspending the supply of outside air. The

system then recirculates the air currently

within the vehicle.

Rear window defroster

Press button.

The rear window defroster switches

Press button repeatedly to select an

operating mode:

off automatically after a certain period of time.

SYNC program

▷

LEDs off: outside air flows in continuously.

Press button.

Left LED on, automatic recirculated-air

control: a sensor detects pollutants in the

outside air and shuts off automatically.

Current settings on the driver's side

for the temperature, air flow, air distribution,

and AUTO program are transferred to the front

passenger side.

▷

Right LED on, recirculated-air mode: the

supply of outside air into the vehicle is per‐

manently blocked.

The program is switched off if the settings on

the front passenger side are changed.

If the windows are fogged over, switch off the

recirculated-air mode and press the AUTO

141

Controls

Climate control

Switching on

Residual heat

The heat stored in the engine is used to heat

the interior.

Press any button except:

▷

Rear window defroster.

Left side of Air volume button.

Seat heating.

Functional requirement

▷

Up to 15 minutes after switching off the

engine.

Seat ventilation.

If necessary, SYNC program.

▷

Warm engine.

The battery is sufficiently charged.

External temperature below 77 ℉/25 ℃.

Microfilter/activated-charcoal filter

The microfilter removes dust and pollen from

the incoming air.

The availability of the function is shown on the

display of the automatic climate control.

The activated-charcoal filter removes gaseous

pollutants from the outside air that enters the

vehicle.

Switching on

1. Switch off the ignition.

This combined filter should be replaced during

scheduled maintenance, refer to page 187, of

your vehicle.

2.

Press the right side of the button

on the driver's side.

The symbol appears on the automatic cli‐

mate Control Display.

Ventilation

The interior temperature, air volume and air

distribution can be adjusted with the ignition

switched on.

Front ventilation

Switch off

At the lowest fan speed, press the left side of

the button on the driver's side.

The symbol on the display of the automatic

climate control flashes.

Switching the system on/off

Switch off

▷

Thumbwheel to vary the temperature, ar‐

row 1.

▷

Complete system:

Press and hold the left button on

the driver's side until the control

clicks off.

On the front passenger side:

Press and hold the left button on

the front passenger side.

Toward blue: colder.

Toward red: warmer.

The set interior temperature for the driver

and passenger are not changed.

▷

Lever for changing the air flow direction,

arrow 2.

Thumbwheels for opening and closing the

vents continuously, arrows 3.

142

Climate control

Controls

Adjusting the ventilation

Activating the reel-on time

▷

Ventilation for cooling:

On the Control Display:

Direct vent in your direction when vehicle's

interior is too hot.

1. "Settings"

2. "Climate"

▷

Draft-free ventilation:

3. "Activate timer 1" or "Activate timer 2"

Adjust the vent to let the air flow past you.

The symbol on the automatic climate con‐

trol lights up when the reel-on time is acti‐

vated.

Parked-car ventilation

The symbol on the automatic climate con‐

trol flashes when the system has been

switched on.

The concept

The parked-car ventilation ventilates the vehi‐

cle interior and lowers its temperature, if

needed.

The system will only be switched on within the

next 24 hours. After that, it needs to be reacti‐

vated.

Operation can be performed via iDrive.

Functional requirements

Parked-car ventilation

▷

Using the preset reel-on time or when op‐

erated directly: any external temperature.

Open the vents to allow air to flow out.

Switching on/off directly

On the Control Display:

1. "Settings"

2. "Climate"

3. "Activate comf. ventilation"

The symbol on the automatic climate con‐

trol flashes if the system is switched on.

The system continues to run for some time af‐

ter being switched off.

Preselecting the reel-on time

On the Control Display:

1. "Settings"

2. "Climate"

3. "Timer 1:" or "Timer 2:"

4. Set the desired time.

143

Controls

Interior equipment

Compatibility

Vehicle features and options

If this symbol is printed on the packag‐

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

ing or in the instructions of the system

to be controlled, the system is gener‐

ally compatible with the universal garage door

opener.

If you have any questions, please contact:

▷

Your service center.

on the Internet.

HomeLink is a registered trademark of Gentex

Corporation.

Universal Integrated Remote

Control

Control elements on the interior

rearview mirror

The concept

The universal garage door opener can operate

up to 3 functions of remote-controlled sys‐

tems such as garage door drives or lighting

systems. The universal garage door opener re‐

places up to 3 different hand-held transmitters.

To operate the remote control, the buttons on

the interior rearview mirror must be program‐

med with the desired functions. The hand-held

transmitter for the particular system is required

in order to program the remote control.

▷

LED, arrow 1.

Buttons, arrow 2.

During programming

The hand-held transmitter, arrow 3, is re‐

quired for programming.

During programming and before activat‐

ing a device using the universal garage door

opener, ensure that there are no people, ani‐

mals or objects in the area of the remote-con‐

trolled device; otherwise, there is a risk of in‐

jury or damage.

Programming

General information

1. Switch on the ignition.

2. Initial setup:

Also follow the safety instructions of the hand-

held transmitter.◀

Press and hold the left and right button on

the interior rearview mirror simultaneously

for approximately 20 seconds until the LED

on the interior rearview mirror flashes. This

Before selling the vehicle, delete the stored

functions for the sake of security.

144

Interior equipment

Controls

erases all programming of the buttons on

the interior rearview mirror.

rearview mirror starts flashing rapidly and then

stays lit constantly for 2 seconds, the system

features an alternating-code system. Flashing

and continuous illumination of the LED will re‐

peat for approximately 20 seconds.

3. Hold the hand-held transmitter for the sys‐

tem to be controlled approx. 1 to 3 in/2.5 to

8 cm away from the buttons of the interior

rearview mirror. The required distance de‐

pends on the manual transmitter.

For systems with an alternating-code system,

the universal garage door opener and the sys‐

tem also have to be synchronized.

4. Simultaneously press and hold the button

of the desired function on the hand-held

transmitter and the button to be program‐

med on the interior rearview mirror. The

LED on the interior rearview mirror will be‐

gin flashing slowly.

Please read the operating manual to find out

how to synchronize the system.

Synchronizing is easier with the aid of a sec‐

ond person.

To synchronize:

5. Release both buttons as soon as the LED

flashes more rapidly. The LED flashing

faster indicates that the button on the inte‐

rior rearview mirror has been programmed.

1. Park the vehicle within range of the re‐

mote-controlled system.

2. Program the relevant button on the interior

rearview mirror as described.

If the LED does not flash faster after at

least 60 seconds, change the distance be‐

tween the interior rearview mirror and the

hand-held transmitter and repeat the step.

Several more attempts at different distan‐

ces may be necessary. Wait at least

15 seconds between attempts.

3. Locate and press the synchronizing button

on the system being programmed. You

have approx. 30 seconds for the next step.

4. Hold down the programmed button on the

interior rearview mirror for approximately

3 seconds and then release it. If necessary,

repeat this step up to three times in order

to finish synchronization. Once synchroni‐

zation is complete, the programmed func‐

tion will be carried out.

Canada: if programming with the hand-

held transmitter was interrupted, hold

down the interior rearview mirror button

and repeatedly press and release the

hand-held transmitter button for 2 sec‐

onds.

Reprogramming individual buttons

6. To program other functions on other but‐

tons, repeat steps 3 to 5.

1. Switch on the ignition.

2. Press and hold the interior rearview mirror

button to be programmed.

The systems can be controlled using the inte‐

rior rearview mirror buttons.

3. As soon as the interior rearview mirror LED

starts flashing slowly, hold the hand-held

transmitter for the system to be controlled

approx. 1 to 3 in/2.5 to 8 cm away from the

buttons of the interior rearview mirror. The

required distance depends on the manual

transmitter.

Special feature of the alternating-

code wireless system

If you are unable to operate the system after

repeated programming, please check if the

system to be controlled features an alternat‐

ing-code system.

Read the system's operating manual, or press

the programmed button on the interior rear‐

view mirror longer. If the LED on the interior

145

Controls

Interior equipment

4. Likewise, press and hold the button of the

desired function on the hand-held trans‐

mitter.

proximately 20 seconds until the LED flashes

rapidly. All stored functions are deleted. The

functions cannot be deleted individually.

5. Release both buttons as soon as the inte‐

rior rearview mirror LED flashes more rap‐

idly. The LED flashing faster indicates that

the button on the interior rearview mirror

has been programmed. The system can

then be controlled by the button on the in‐

terior rearview mirror.

Sun visor

Glare shield

Fold the sun visor down or up.

Vanity mirror

If the LED does not flash faster after at

least 60 seconds, change the distance and

repeat the step. Several more attempts at

different distances may be necessary. Wait

at least 15 seconds between attempts.

A vanity mirror is located in the sun visor be‐

hind a cover. When the cover is opened, the

mirror lighting switches on.

Canada: if programming with the hand-

held transmitter was interrupted, hold

down the interior rearview mirror button

and repeatedly press and release the

hand-held transmitter button for 2 sec‐

onds.

Ashtray/cigarette lighter

Manual transmission: opening

Controls

Before operation

Before operating a system using the uni‐

versal garage door opener, ensure that there

are no people, animals, or objects within the

range of movement of the remote-controlled

system; otherwise, there is a risk of injury or

damage.

Press on the cover.

Also follow the safety instructions of the hand-

held transmitter.◀

Open

The system, such as the garage door, can be

operated using the button on the interior rear‐

view mirror while the engine is running or when

the ignition is started. To do this, hold down

the button within receiving range of the system

until the function is activated. The interior rear‐

view mirror LED stays lit while the wireless sig‐

nal is being transmitted.

Press button.

Deleting stored functions

Press and hold the left and right button on the

interior rearview mirror simultaneously for ap‐

146

Interior equipment

Controls

Emptying

Take out the insert.

Sockets

General information

The lighter socket can be used as a socket for

electrical equipment while the engine is run‐

ning or when the ignition is switched on.

Lighter

Push in the lighter.

The lighter can be removed as

soon as it pops back out.

Note

The total load of all sockets must not exceed

140 watts at 12 volts.

Danger of burns

Do not damage the socket by using unsuitable

connectors.

Only hold the hot lighter by its knob; oth‐

erwise, there is a danger of getting burned.

Switch off the ignition and take the remote

control with you when leaving the vehicle so

that children cannot use the lighter and burn

themselves.◀

Manual transmission: center console

Replace the cover after use

Reinsert the lighter or socket cover after

use, otherwise objects may get into the lighter

socket or fixture and cause a short circuit.◀

Press on the cover.

Connecting electrical

devices

Remove the cover or cigarette lighter.

Hints

Center console

Do not connect charging devices to the

12 volt socket in the vehicle

Do not connect battery chargers to the fac‐

tory-installed 12 volt sockets in the vehicle as

this may damage the vehicle battery due to an

increased power consumption.◀

Replace the cover after use

Reinsert the lighter or socket cover after

use, otherwise objects may get into the lighter

socket or fixture and cause a short circuit.◀

Press button.

Remove the cover or cigarette lighter.

147

Controls

Interior equipment

necessary, when pulling the release, press

against the insert.

In the front passenger footwell

Socket is located below the glove compart‐

ment.

2. Lay out the ski bag.

To access the socket: fold open the cover.

3. Press button in the cargo area, open tail‐

board and attach to the rear wall via mag‐

netic holder.

Center armrest

4. Load the ski bag. If necessary, wrap the

sharp edges of the skis.

Remove the cover.

5. Tighten the retaining strap.

Ski bag

Capacity

The ski bag makes it possible to transport two

pairs of skis up to a length of 6 ft/2.10 m.

Preparing and loading the ski bag

1. Pull the release in the direction of the ar‐

row, and remove the insert from the front. If

Securing the ski bag

Secure the ski bag by tightening the re‐

taining strap; otherwise, the contents could

present a source of danger to the passengers,

for example during braking or evasive maneu‐

vers.◀

148

Interior equipment

Controls

Stowing the ski bag

Proceed in the reverse order of loading.

When replacing the insert, place both pins into

the rail at the bottom and press the insert back

in place until a 'click' is heard. Ensure that the

rear seat backrest upholstery is not damaged.

149

Controls

Storage compartments

Vehicle features and options

Glove compartment

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Note

Close the glove compartment again im‐

mediately

Close the glove compartment immediately af‐

ter use while driving; otherwise, injury may oc‐

cur during accidents.◀

Opening

Hints

No loose objects in the car's interior

Do not stow any objects in the car's inte‐

rior without securing them; otherwise, they

may present a danger to occupants e.g., during

braking and evasive maneuvers.◀

Do not place anti-slip mats on the dash‐

board

Pull the handle.

The light in the glove compartment switches

on.

Do not place anti-slip mats on the dashboard.

The mat materials could damage the dash‐

board.◀

Closing

Fold cover closed.

Storage compartments

The following storage compartments are avail‐

able in the vehicle interior:

USB interface for data transfer

The concept

Connection for importing and exporting data

on USB devices, e.g.:

▷

Glove compartment on the front passenger

side, refer to page 150.

Storage compartment on the center con‐

sole: manual transmission.

▷

Personal Profile settings, refer to page 35.

Music collection, see user's manual for

Navigation, Entertainment and Communi‐

cation.

Storage compartment in the center arm‐

rest, refer to page 151.

▷

Compartments in the doors.

Hints

Pockets on the backrests of the front

seats.

Observe the following when connecting:

▷

Net in the front passenger footwell.

150

Storage compartments

Controls

▷

Do not use force when plugging the con‐

nector into the USB interface.

Locking the storage compartment

Do not connect devices such as fans or

lights to the USB interface.

▷

Do not connect USB hard drives.

Do not use the USB interface for recharg‐

ing external devices.

With navigation system Professional

or TV: at a glance

The storage compartment in the armrest can

be locked with an integrated key to separately

secure the trunk lid, refer to page 41, e.g.

After the storage compartment is locked, the

remote control can be handed out without the

integrated key, refer to page 34, for instance at

a hotel.

This prevents access to the storage compart‐

ment and to the cargo area.

The USB interface is located in the center arm‐

rest.

Connection for an external audio

device

An external audio device, e.g.,

an MP3 player, can be con‐

nected via the AUX-IN port or

the USB audio interface in the

center armrest.

Front center armrest

Opening

A storage compartment is located in the center

armrest between the front seats.

Clothes hooks

Do not obstruct view

When suspending clothing from the

hooks, ensure that it will not obstruct the driv‐

er's view.◀

No heavy objects

Do not hang heavy objects from the

hooks; otherwise, they may present a danger

to passengers during braking and evasive ma‐

neuvers.◀

Press buttons next to the lock.

151

Controls

Storage compartments

Two folding clothes hooks are provided in the

rear of the vehicle. To unfold them, press on

the top edge of the clothes hooks.

To open: press the buttons next to the lock.

Center console

Cupholders

Hints

Shatter-proof containers and no hot

drinks

Use light and shatter-proof containers and do

not transport hot drinks. Otherwise, there is

the increased danger of injury in an accident.◀

To open: press on the cover.

Unsuitable containers

Do not forcefully push unsuitable con‐

tainers into the cupholders. This may result in

damage.◀

Storage compartments in the

cargo area

Net

Manual transmission: center console

Small objects can be stowed in the net on the

rear cargo area trim.

Lashing eyes

To secure the cargo, refer to page 163, there

are lashing eyes in the cargo area.

Storage under the cargo floor panel

A cupholder is located on the center console.

Manual transmission: center armrest

Raise the cargo floor panel using the strap.

A cupholder is located in the center armrest

compartment.

152

Storage compartments

Controls

153

Controls for Your BMW M6 4 Door Third Generation (2012-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals