Get Mobility Guide for BMW M6 4 Door Third Generation (2012-2019)

Mobility

In order to always ensure your mobility, you will

find important information on operating fluids,

wheels and tires, maintenance and Roadside

Assistance in the following.

Mobility

Refueling

2. Turn the tank lid counterclockwise.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

3. Place the tank lid in the bracket attached to

the fuel filler flap.

Hints

Observe the fuel recommendation, refer to

page 170, prior to refueling.

Refuel promptly

Refuel no later than at a range of

30 miles/50 km or engine operation might fail

and damage might occur.◀

Fuel lid

Closing

1. Fit the lid and turn it clockwise until you

clearly hear a click.

Opening

1. Briefly press the rear edge of the fuel filler

flap.

2. Close the fuel filler flap.

Do not pinch the retaining strap

Do not pinch the retaining strap attached

to the lid; otherwise, the lid cannot be closed

properly and fuel vapors can escape.◀

Manually unlocking fuel filler flap

In the event of an electrical malfunction, e.g.

The release is located in the trunk.

168

Refueling

Mobility

1. Open the cover on the right side trim.

2. Pull the green knob with the fuel pump

symbol. This releases the fuel filler flap.

Observe the following when

refueling

The fuel tank is full when the filler nozzle clicks

off the first time.

Do not overfill the fuel tank

Do not overfill the fuel tank; otherwise

fuel may eslide, causing harm to the environ‐

ment and damaging the vehicle.◀

Handling fuels

Observe safety regulations posted at the

gas station.◀

169

Mobility

Fuel

Ethanol should satisfy the following quality

standards:

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

US: ASTM 4806–xx

CAN: CGSB-3.511–xx

xx: comply with the current standard in each

case.

Do not use a fuel with a higher percent‐

age of ethanol

Do not use a fuel with a higher ethanol per‐

centage than recommended or one with other

types of alcohol, e.g. M5 to M100; otherwise

this could damage the engine and fuel supply

system.◀

Fuel recommendation

Note

Recommended fuel grade

BMW recommends AKI 93.

General fuel quality

Even fuels that conform to the specifica‐

tions can be of low quality. This may cause en‐

gine problems, for instance poor engine start-

up behavior, poor handling and/or poor

Minimum fuel grade

BMW recommends AKI 91.

performance. Switch gas stations or use a

brand name fuel with a higher octane rating.◀

Minimum fuel grade

Do not use any gasoline below the mini‐

mum fuel grade as this may impair engine per‐

formance.◀

Gasoline

For the best fuel efficiency, the gasoline

should be sulfur-free or very low in sulfur con‐

tent.

If you use gasoline with this minimum AKI Rat‐

ing, the engine may produce knocking sounds

when starting at high outside temperatures.

This has no effect on the engine life.

Fuels that are marked on the gas pump as con‐

taining metal must not be used.

Fuel quality

Refuel only with unleaded gasoline with‐

out metallic additives.

The use of poor-quality fuels may result

in harmful engine deposits or damage. Addi‐

tionally, problems relating to drivability, start‐

ing and stalling, especially under certain envi‐

ronmental conditions such as high ambient

temperature and high altitude, may occur.

Do not refuel with any leaded gasoline or gaso‐

line with metallic additives, e. g. manganese or

iron, as this can cause permanent damage to

the catalytic converter and other compo‐

nents.◀

If drivability problems are encountered, we rec‐

ommend switching to a high quality gasoline

brand and a higher octane grade — AKI num‐

ber — for a few tank fills. To avoid harmful en‐

Fuels with a maximum ethanol content of

10 %, i. e., E10, may be used for refueling.

170

Fuel

Mobility

gine deposits, it is highly recommended to

purchase gasoline from Top Tier retailers.

Failure to comply with these recommendations

may result in the need for unscheduled main‐

tenance.◀

171

Mobility

Wheels and tires

Only check the tire inflation pressure when the

tires are cold. This means after driving no more

than 1.25 miles/2 km or when the vehicle has

been parked for at least 2 hours.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

The displays of inflation devices may under-

read by up to 1.45 psi/0.1 bar.

For Flat Tire Monitor: after correcting the tire

inflation pressure, reinitialize the Flat Tire

Monitor.

For Tire Pressure Monitor: after correcting the

tire inflation pressure, reset the Tire Pressure

Monitor.

Tire inflation pressure

Tire inflation pressure specifications

Safety information

The tire characteristics and tire inflation pres‐

sure influence the following:

The tire inflation pressure table, refer to

page 173, contains all tire inflation pressure

specifications for the specified tire sizes at the

ambient temperature. Tire inflation pressure

specifications apply to approved tire sizes and

recommended tire brands. This information

can be obtained from your service center.

▷

The service life of the tires.

Road safety.

Driving comfort.

To identify the correct tire inflation pressure,

please note the following:

Checking the tire inflation pressure

Check the tire inflation pressure regularly

▷

Tire sizes of your vehicle.

Regularly check the tire inflation pres‐

sure, and correct it as needed: at least twice a

month and before a long trip. If you fail to ob‐

serve this precaution, you may be driving on

tires with incorrect tire pressures, a condition

that may not only compromise your vehicle's

driving stability, but also lead to tire damage

and the risk of an accident.◀

Maximum permitted driving speed.

Tire inflation pressures up to

100 mph/160 km/h

For speeds of up to 100 mph/160 km/h and for

optimum driving comfort, note the pressure

values in the tire inflation pressure table, refer

to page 173, and adjust as necessary.

Tires have a natural, consistent loss of tire in‐

flation pressure.

Tires heat up while driving, and the tire infla‐

tion pressure increases along with the tire's

temperature. The tire inflation pressure speci‐

fications relate to cold tires or tires with the

ambient temperature.

172

Wheels and tires

Mobility

Tire inflation pressures at max.

speeds above 100 mph/160 km/h

Speeds above 100 mph/160 km/h

In order to drive at maximum speeds in

excess of 100 mph/160 km/h, please observe,

and, if necessary, adjust tire pressures for

speeds exceeding 100 mph/160 km/h from the

relevant table on the following pages. Other‐

wise tire damage and accidents could occur.◀

These pressure values can also be found on

the tire inflation pressure label on the driver's

door pillar.

Tire inflation pressure values over

100 mph/160 km/h

Maximum permissible speed

M6

Do not exceed 100 mph/160 km/h; other‐

wise, tire damage and accidents may result.◀

Tire size

Pressure specifications

in bar/PSI

Tire inflation pressure values up to

100 mph/160 km/h

Specifications in

bar/PSI with cold

tires

M6

Tire size

Pressure specifications

in bar/PSI

255/40 R 19 100

V M+S XL

2.6 / 37

3.0 / 43

2.8 / 40

3.2 / 46

Specifications in

bar/PSI with cold

tires

255/35 R 20 97

V M+S XL

Front: 265/40 ZR

19 102 (Y) XL

2.4 / 34

-

2.4 / 34

255/40 R 19 100

V M+S XL

2.5 / 36

Rear: 295/35 ZR

19 104 (Y) XL

255/35 R 20 97

V M+S XL

Front: 265/35 ZR

20 99 (Y) XL

2.5 / 36

-

2.5 / 36

Front: 265/40 ZR

19 102 (Y) XL

2.2 / 31

-

Rear: 295/30 ZR

20 101 (Y) XL

2.2 / 31

Rear: 295/35 ZR

19 104 (Y) XL

Front: 265/35 ZR

20 99 (Y) XL

2.4 / 34

-

Tire identification marks

2.4 / 34

Rear: 295/30 ZR

20 101 (Y) XL

Tire size

245/45 R 18 96 Y

245: nominal width in mm

173

Mobility

Wheels and tires

45: aspect ratio in %

R: radial tire code

DOT Quality Grades

Treadwear

18: rim diameter in inches

Traction AA A B C

Temperature A B C

96: load rating, not for ZR tires

Y: speed rating, before the R on ZR tires

All passenger car tires must conform to Fed‐

eral Safety Requirements in addition to these

grades.

Speed letter

Q = up to 100 mph, 160 km/h

R = up to 106 mph, 170 km/h

S = up to 112 mph, 180 km/h

T = up to 118 mph, 190 km/h

H = up to 131 mph, 210 km/h

V = up to 150 mph, 240 km/h

W = up to 167 mph, 270 km/h

Y = up to 186 mph, 300 km/h

Treadwear

The treadwear grade is a comparative rating

based on the wear rate of the tire when tested

under controlled conditions on a specified gov‐

ernment test course. For example, a tire

graded 150 would wear one and one-half, 1 g,

times as well on the government course as a

tire graded 100. The relative performance of

tires depends upon the actual conditions of

their use, however, and may depart signifi‐

cantly from the norm due to variations in driv‐

ing habits, service practices and differences in

road characteristics and climate.

Tire Identification Number

DOT code: DOT xxxx xxx 0115

xxxx: manufacturer code for the tire brand

xxx: tire size and tire design

0115: tire age

Traction

The traction grades, from highest to lowest,

are AA, A, B, and C.

Tires with DOT codes meet the guidelines of

the U.S. Department of Transportation.

Those grades represent the tire's ability to

stop on wet pavement as measured under

controlled conditions on specified government

test surfaces of asphalt and concrete. A tire

marked C may have poor traction performance.

Tire age

DOT … 0115: the tire was manufactured in the

1st week of 2015.

The traction grade assigned to this tire is

based on straight-ahead braking traction tests,

and does not include acceleration, cornering,

hydroplaning, or peak traction characteristics.

Recommendation

Regardless of wear and tear, replace tires at

least every 6 years.

Uniform Tire Quality Grading

Temperature

Quality grades can be found where applicable

on the tire sidewall between tread shoulder

and maximum section width.

The temperature grades are A, the highest, B,

and C, representing the tire's resistance to the

generation of heat and its ability to dissipate

heat when tested under controlled conditions

on a specified indoor laboratory test wheel.

Sustained high temperature can cause the ma‐

terial of the tire to degenerate and reduce tire

life, and excessive temperature can lead to

For example: Treadwear 200; Traction AA;

Temperature A

174

Wheels and tires

Mobility

sudden tire failure. The grade C corresponds

to a level of performance which all passenger

car tires must meet under the Federal Motor

Vehicle Safety Standard No. 109. Grades Band

A represent higher levels of performance on

the laboratory test wheel than the minimum re‐

quired by law.

Minimum tread depth

Temperature grade for this tire

The temperature grade for this tire is es‐

tablished for a tire that is properly inflated and

not overloaded. Excessive speed, underinfla‐

tion, or excessive loading, either separately or

in combination, can cause heat buildup and

possible tire failure.

Wear indicators are distributed around the

tire's circumference and have the legally re‐

quired minimum height of 0.063 in/1.6 mm.

They are marked on the side of the tire with

TWI, Tread Wear Indicator.

If necessary, have the vehicle towed.◀

M+S

Winter and all-season tires with better cold

weather performance than summer tires.

Tire damage

General information

Inspect your tires often for damage, foreign

objects lodged in the tread, and tread wear.

Tire tread

Summer tires

Hints

Do not drive with a tire tread depth of less than

0.12 in/3 mm.

Driving over rough or damaged road surfaces,

as well as debris, curbs and other obstacles

can cause serious damage to wheels, tires and

suspension parts. This is more likely to occur

with low-profile tires, which provide less cush‐

ioning between the wheel and the road. Be

careful to avoid road hazards and reduce your

speed, especially if your vehicle is equipped

with low-profile tires.

There is an increased danger of hydroplaning if

the tire tread depth is less than 0.12 in/3 mm.

Winter tires

Do not drive with a tire tread depth of less than

0.16 in/4 mm.

Below a tread depth of 0.16 in/4 mm, tires are

less suitable for winter operation.

Indications of tire damage or other vehicle de‐

fects:

▷

Unusual vibrations while driving.

Unusual handling such as a strong ten‐

dency to pull to the left or right.

Damage can, e. g., be caused by driving over

curbs, road damage, or similar things.

175

Mobility

Wheels and tires

In case of tire damage

Approved wheels and tires

If there are indications of tire damage, re‐

duce your speed immediately and have the

rims and tires checked right away; otherwise,

there is the increased risk of an accident.

You should only use wheels and tires

that have been approved by the vehicle manu‐

facturer for your vehicle type; otherwise, e.g.,

despite having the same official size ratings,

variations can lead to chassis contact and with

it, the risk of severe accidents

Drive carefully to the nearest service center. If

necessary, have the vehicle towed or trans‐

ported there. Otherwise, tire damage can be‐

come life threatening for vehicle occupants

and also other traffic.◀

The manufacturer of your vehicle cannot eval‐

uate non-approved wheels and tires to deter‐

mine if they are suited for use, and therefore

cannot guarantee the operating safety of the

vehicle.◀

Repair of tire damage

For safety reasons, the manufacturer of

your vehicle recommends that you do not have

damaged tires repaired; they should be re‐

placed. Otherwise, damage can occur as a re‐

sult.◀

Recommended tire brands

Changing wheels and tires

Mounting

Information on mounting tires

For each tire size, the manufacturer of your ve‐

hicle recommends certain tire brands. These

can be identified by a star on the tire sidewall.

Have mounting and balancing performed

only by a service center.

If work is not carried out properly, there is a

danger of subsequent damage and related

safety hazards.◀

With proper use, these tires meet the highest

standards for safety and handling.

Wheel and tire combination

New tires

You can ask the service center about the right

wheel/tire combination and wheel rim versions

for the vehicle.

Tire traction is not optimal due to manufactur‐

ing circumstances when tires are brand-new;

they achieve their full traction potential after a

break-in time.

Incorrect wheel and tire combinations impair

the function of a variety of systems such as

ABS or DSC.

Drive conservatively for the first

200 miles/300 km.

To maintain good handling and vehicle re‐

sponse, use only tires with a single tread con‐

figuration from a single manufacturer.

Retreaded tires

The manufacturer of your vehicle does not rec‐

ommend the use of retreaded tires.

Following tire damage, have the original wheel

and tire combination remounted on the vehicle

as soon as possible.

176

Wheels and tires

Mobility

Retreaded tires

Repairing a flat tire

Possibly substantial variations in the de‐

sign and age of the tire casing structures can

limit service life and have a negative impact on

road safety.◀

Safety measures in case of a breakdown

Park the vehicle as far away as possible

from passing traffic and on solid ground.

Switch on the hazard warning system.

Winter tires

Winter tires are recommended for operating on

winter roads.

Turn the steering wheel until the front wheels

are in the straight-ahead position and engage

the steering wheel lock.

Secure the vehicle against rolling away by set‐

ting the parking brake.

Although so-called all-season M+S tires pro‐

vide better winter traction than summer tires,

they do not provide the same level of perform‐

ance as winter tires.

Have all vehicle occupants get out of the vehi‐

cle and ensure that they remain outside the

immediate area in a safe place, such as behind

a guardrail.

Maximum speed of winter tires

If the maximum speed of the vehicle is higher

than the permissible speed for the winter tires,

then a respective symbol is displayed in your

field of vision. You can obtain this sign from the

tire specialist or from your service center.

If necessary, set up a warning triangle at an ap‐

propriate distance.

Comply with all safety guidelines and regula‐

tions.◀

Maximum speed for winter tires

Do not exceed the maximum speed for

the respective winter tires; otherwise, tire dam‐

age and accidents can occur.◀

Mobility System

The concept

With the Mobility System, minor tire damage

can be sealed quickly to enable continued

travel. To accomplish this, sealant is pumped

into the tires, which seals the damage from the

inside.

Rotating wheels between axles

The manufacturer of your vehicle advises

against switching wheels between the front

and rear axles. This can impair the handling

characteristics.

The compressor can be used to check the tire

inflation pressure.

Rotating the tires is not permissible on vehi‐

cles with different tire sizes or rim sizes on the

front and rear axles.

Hints

▷

Follow the instructions on using the Mobi‐

lity System found on the compressor and

sealant container.

Storage

Store wheels and tires in a cool, dry place with

as little exposure to light as possible.

Use of the Mobility System may be ineffec‐

tive if the tire puncture measures approx.

1/8 in/4 mm or more.

Always protect tires against all contact with oil,

grease and fuels.

Contact the nearest service center if the

tire cannot be made drivable.

Do not exceed the maximum tire inflation pres‐

sure indicated on the side wall of the tire.

177

Mobility

Wheels and tires

▷

If possible, do not remove foreign bodies

that have penetrated the tire.

Compressor

Pull the speed limit sticker off the sealant

container and apply it to the steering

wheel.

▷

The use of a sealant can damage the TPM

wheel electronics. In this case, have the

electronics checked at the next opportu‐

nity and have them replaced if needed.

Enclosed areas

1

2

3

4

5

6

7

Holder for bottle

Do not let the engine run in enclosed

Compressor

areas, since breathing in exhaust fumes may

lead to loss of consciousness and death. The

exhaust gases contain carbon monoxide, an

odorless and colorless but highly toxic gas.◀

Connector/cable for socket

Connection hose

On/off reel

Inflation pressure dial

Reduce inflation pressure

Storage

The Mobility System is located under the

cargo floor panel.

Filling the tire with sealant

1. Shake the sealing container.

Sealing container

▷

Sealing container, arrow 1.

Filling hose, arrow 2.

2. Pull the connection hose fully out of the

compressor housing. Do not kink the hose.

Observe use-by date on the sealant container.

178

Wheels and tires

Mobility

3. Screw the connection hose onto the con‐

nector of the sealant container.

6. With the compressor switched off, insert

the plug into the power socket inside the

vehicle.

4. Insert the sealant container on the com‐

pressor housing in an upright position.

7. With the ignition turned on or the engine

running, reel on the compressor.

5. Screw the filling hose of the sealant con‐

tainer onto the tire valve of the defective

wheel.

Switch off the compressor after 10 mi‐

nutes

Do not allow the compressor to run longer than

10 minutes; otherwise, the device will overheat

and may be damaged.◀

Let the compressor run for approx. 3 to 8 mi‐

nutes to fill the tire with sealant and achieve a

tire inflation pressure of approx. 2.5 bar.

While the tire is being filled with sealant, the

tire inflation pressure may sporadically reach

approx. 5 bar. Do not reel off the compressor at

this point.

If a tire inflation pressure of 2 bar is not

reached:

1. Switch off the compressor.

2. Unscrew the filling hose from the wheel.

3. Drive 33 ft/10 m forward and back to dis‐

tribute the sealant in the tire.

4. Inflate the tire again using the compressor.

179

Mobility

Wheels and tires

If a tire inflation pressure of 2 bar cannot be

reached, contact your service center.

Continuing the trip

Do not exceed the maximum permissible

speed of 50 mph/80 km/h.

Stowing the Mobility System

1. Unscrew the filling hose of the sealant con‐

tainer from the wheel.

Reinitialize the Flat Tire Monitor.

Reinitialize the Tire Pressure Monitor.

Replace the defective tire and the sealant con‐

tainer of the Mobility System as soon as possi‐

ble.

2. Unscrew the connection hose of the com‐

pressor from the sealant container.

3. Connect the filling hose of the sealant con‐

tainer previously connected to the tire

valve with the available connector on the

sealant container.

Snow chains

This prevents leftover sealant from escap‐

ing from the container.

Fine-link snow chains

Only certain types of fine-link snow chains

have been tested by the manufacturer of the

vehicle, classified as road-safe and approved.

4. Wrap the empty sealant container in suita‐

ble material to avoid dirtying the cargo

area.

Information about the approved snow chains

are available from the service center.

5. Stow the Mobility System back in the vehi‐

cle.

Use

Distributing the sealant

Use only in pairs on the rear wheels, equipped

with the tires of the following size:

Immediately drive approx. 5 miles/10 km to en‐

sure that the sealant is evenly distributed in the

tire.

▷

255/40 R 19

255/35 R 20

Do not exceed a speed of 50 mph/80 km/h.

Follow the snow chain manufacturer's instruc‐

tions.

If possible, do not drive at speeds less than

12 mph/20 km/h.

Make sure that the snow chains are always

sufficiently tight. Retighten as needed accord‐

ing to the chain manufacturer's instructions.

To correct the tire inflation pressure

1. Stop at a suitable location.

Do not initialize the Flat Tire Monitor after

mounting snow chains, as doing so may result

in incorrect readings.

2. Screw the connection hose of the com‐

pressor directly onto the tire valve stem.

3. Insert the connector into the power socket

inside the vehicle.

Do not initialize the Tire Pressure Monitor after

mounting snow chains, as doing so may result

in incorrect readings.

4. Correct the tire inflation pressure to

2.5 bar.

When driving with snow chains, if needed

briefly activate M Dynamic Mode.

▷

Increase pressure: with the ignition

turned on or the engine running, reel

on the compressor.

Maximum speed with snow chains

▷

To reduce the pressure: press the but‐

ton on the compressor.

Do not exceed a speed of 30 mph/50 km/h

when using snow chains.

180

Engine compartment

Mobility

Engine compartment

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

Important features in the engine compartment

1

2

3

4

Vehicle identification number

5

6

7

Coolant reservoir for charge air cooling

Oil filler neck.

Jump-starting, negative battery terminal

Washer fluid reservoir

Coolant reservoir for engine cooling

Jump-starting, positive battery terminal

If you are unfamiliar with the statutory guide‐

lines, have any work on the vehicle performed

only by a service center.

Hood

Opening the hood

If work is not carried out properly, there is a

danger of subsequent damage and related

safety hazards.◀

Working in the engine compartment

Never attempt to perform any service or

repair operations on your vehicle without the

necessary professional technical training.

181

Mobility

Engine compartment

Never reach into the engine compart‐

ment

Closing the hood

Hood open when driving

Never reach into spaces or gaps in the engine

compartment; otherwise, there is a risk of in‐

jury, e.g., from rotating or hot parts.◀

If you see any signs that the hood is not

completely closed while driving, pull over im‐

mediately and close it securely.◀

Danger of injury when the hood is open

Danger of jamming

There is a danger of injury from protrud‐

ing parts when the hood is open.◀

Make sure that the closing path of the

hood is clear; otherwise, injuries may result.◀

1. Pull the lever.

Let the hood drop from a height of approx. 16

in/40 cm and push down on it to lock it fully.

2. Press the release handle and open the

hood.

The hood must audibly engage on both sides.

3. Be careful of protruding parts on the hood.

182

Engine oil

Mobility

Engine oil

Vehicle features and options

Electronic oil measurement

Status display

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

The concept

The engine oil level is monitored electronically

while driving and shown on the Control Dis‐

play.

If the engine oil level reaches the minimum

level, a check control message is displayed.

Requirements

General information

The engine oil consumption is dependent on

the driving style and driving conditions.

A current measured value is available after ap‐

prox. 30 minutes of driving. During a shorter

trip, the status of the last, sufficiently long trip

is displayed.

The engine oil consumption can increase in

case of, for example:

With frequent short-distance trips, regularly

perform a detailed measurement.

▷

Sporty driving.

Break-in the engine.

Displaying the engine oil level

On the Control Display:

Idling of the engine.

Usage of non-approved engine oil grades.

1. "Vehicle info"

Therefore, regularly check the engine oil level

after refueling.

2. "Vehicle status"

3.

"Engine oil level"

When a dynamic driving style is used, such as

when cornering fast, the system is unable to

measure the engine oil level. With this driving

style, measure the engine oil level using a de‐

tailed measurement, refer to page 184.

Engine oil level display messages

Different messages appear on the display de‐

pending on the engine oil level. Pay attention

to these messages.

The vehicle is equipped with electronic oil

measurement.

If the engine oil level is too low, within the next

125 miles/200 km Add engine oil, refer to

page 184.

The electronic oil measurement has two meas‐

uring principles:

Engine oil level too low

▷

Status display

Add engine oil immediately; otherwise,

an insufficient amount of engine oil could re‐

sult in engine damage.◀

Detailed measurement

Take care not to add too much engine oil.

183

Mobility

Engine oil

Too much engine oil

Adding engine oil

Have the vehicle checked immediately;

otherwise, surplus engine oil can lead to en‐

gine damage.◀

General information

Switch off the ignition and safely park the vehi‐

cle before engine oil is added.

Detailed measurement

The concept

Oil filler neck

In the detailed measurement the engine oil

level is checked and displayed via a scale.

Gasoline engine:

If the engine oil level reaches the minimum

level, a check control message is displayed.

Diesel engine:

During the measurement, the idle speed is in‐

creased somewhat.

Only add engine oil when the message is dis‐

played in the instrument cluster. The quantity

to be added is indicated in the message dis‐

played in the instrument cluster.

Requirements

▷

Vehicle is on level road.

Manual transmission: shift lever in neutral

position, clutch and accelerator pedals not

depressed.

Adding engine oil

Add oil within the next 125 miles/200 km;

otherwise, this may cause engine damage.◀

▷

M Double clutch transmission: selector

lever in selector lever position N and accel‐

erator pedal not depressed.

Do not add too much engine oil

When too much engine oil is added, im‐

mediately have the vehicle checked, otherwise,

this may cause engine damage.◀

Engine is running and is at operating tem‐

perature.

Performing a detailed measurement

Protect children

In order to perform a detailed measurement of

the engine oil level:

Keep oil, grease, etc., out of reach of chil‐

dren and observe the warnings on the contain‐

ers to prevent health risks.◀

1. "Vehicle info"

2. "Vehicle status"

3.

"Measure engine oil level"

Engine oil types to add

4. "Start measurement"

The engine oil level is checked and displayed

via a scale.

Hints

No oil additives

Time: approx. 1 minute.

Oil additives may lead to engine dam‐

age.◀

184

Engine oil

Mobility

Viscosity grades for engine oils

When selecting an engine oil, ensure that

the engine oil belongs to the viscosity grade

SAE 0W-40, or malfunctions or engine dam‐

age may occur.

As an alternative, you can also use motor oils

with a viscosity grade of SAE 0W-30.◀

The engine oil quality is critical for the life of

the engine.

Suitable engine oil types

You can add engine oils that meet the follow‐

ing oil rating standards:

Oil rating

BMW Longlife-01.

BMW Longlife-01 FE.

Further information regarding the oil specifica‐

tions and viscosities of engine oils can be in‐

quired with the service center.

Alternative engine oil types

If an engine oil suitable for continuous use is

not available, up to 1 US quart/liter of an en‐

gine oil with the following oil rating can be

added:

Oil rating

API SM or superior oil rating.

Engine oil change:

The vehicle manufacturer recommends that

you let the service center change the motor oil.

185

Mobility

Coolant

Vehicle features and options

Disposal

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Comply with the relevant environmen‐

tal protection regulations when dispos‐

ing of coolant and coolant additives.

Hints

Danger of burns from hot engine

Do not open the cooling system while

the engine is hot; otherwise, esliding coolant

may cause burns.◀

Suitable additives

Only use suitable additives; otherwise,

engine damage may occur. The additives are

harmful to your health.◀

Coolant consists of water and additives.

Not all commercially available additives are

suitable for the vehicle. Information about the

suitable additives are available from the service

center.

Coolant level

General information

Have your service center check the coolant

level and add coolant if needed.

186

Maintenance

Mobility

Maintenance

Service data in the remote control

Vehicle features and options

Information on the required maintenance is

continuously stored in the remote control.

Your service center will read out this data and

suggest the right array of service procedures

for your vehicle.

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

Therefore, hand your service specialist the re‐

mote control with which the vehicle was driven

most recently.

Storage periods

Storage periods during which the vehicle bat‐

tery was disconnected are not taken into ac‐

count.

BMW maintenance system

The maintenance system indicates required

maintenance measures, and thereby provides

support in maintaining road safety and the op‐

erational reliability of the vehicle.

If this occurs, have a service center update the

time-dependent maintenance procedures,

such as checking brake fluid and, if needed,

changing the engine oil and the microfilter/

activated-charcoal filter.

In some cases scopes and intervals may vary

according to the country-specific version. Re‐

placement work, spare parts, fuels and lubri‐

cants and wear materials are calculated sepa‐

rately. Additional information is available from

the service center.

Service and Warranty

Information Booklet for US

models and Warranty and

Service Guide Booklet for

Canadian models

Please consult your Service and Warranty In‐

formation Booklet for US models and Warranty

and Service Guide Booklet for Canadian mod‐

els for additional information on service re‐

quirements.

Condition Based Service

CBS

Sensors and special algorithms take into ac‐

count the driving conditions of your vehicle.

Based on this, Condition Based Service recog‐

nizes the maintenance requirements.

The system makes it possible to adapt the

amount of maintenance corresponding to your

user profile.

Maintenance and repair should be performed

by your service center. Make sure to have reg‐

ular maintenance procedures recorded in the

vehicle's Service and Warranty Information

Booklet for US models, and in the Warranty

and Service Guide Booklet for Canadian mod‐

els. These entries are proof of regular mainte‐

nance.

Detailed information on service requirements,

refer to page 85, can be displayed on the Con‐

trol Display.

187

Mobility

Maintenance

Socket for OBD Onboard

Diagnosis

Note

Socket for Onboard Diagnosis

The socket for onboard diagnostics may

only be used by the service center or a work‐

shop that operates in accordance with the

specifications of the vehicle manufacturer with

correspondingly trained personnel and other

authorized persons. Otherwise, use may result

in operating problems for the vehicle.◀

Position

There is an OBD socket on the driver's side for

checking the primary components in the vehi‐

cle's emissions.

Emissions

▷

The warning lamp lights up:

Emissions are deteriorating. Have

the vehicle checked as soon as

possible.

▷

The warning lamp flashes under certain

circumstances:

This indicates that there is excessive mis‐

firing in the engine.

Reduce the vehicle speed and have the

system checked immediately; otherwise,

serious engine misfiring within a brief pe‐

riod can seriously damage emission con‐

trol components, in particular the catalytic

converter.

188

Replacing components

Mobility

Replacing components

Replacing the wiper blades

1. To change the wiper blades, fold up, refer

to page 71, the wiper arms.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

2. Fold up the wipers.

Onboard vehicle tool kit

3. Position the wiper blade in a horizontal po‐

sition.

4. Remove the wiper blade toward one side.

The onboard vehicle tool kit is located under

the cargo floor panel.

5. Insert the new wiper blade in reverse order

of removal until it locks in place.

Wiper blade replacement

6. Fold down the wipers.

Hints

Do not fold down the wipers without

wiper blades

Lamp and bulb replacement

Do not fold down the wipers if wiper blades

have not been installed; this may damage the

windshield.◀

Hints

Lights and bulbs

Lights and bulbs make an essential contribu‐

tion to vehicle safety.

The manufacturer of the vehicle recommends

that you entrust corresponding procedures to

189

Mobility

Replacing components

the service center if you are unfamiliar those or

if they have not been described here.

If the headlights do not dim despite driving

with the light switched on, increasing humidity

forms, e. g. water droplets in the light, have the

service center check this.

You can obtain a selection of replacement

bulbs at the service center.

Danger of burns

Headlight setting

Only change bulbs when they are cool;

otherwise, there is a danger of getting

burned.◀

The headlight adjustments can be affected by

changing lights and bulbs. Have the head‐

lights' settings checked and corrected by serv‐

ice after a replacement.

Working on the lighting system

When working on the lighting system,

you should always reel off the lights affected to

prevent short circuits.

Front lights, bulb replacement

LED headlights

To avoid possible injury or equipment damage

when replacing bulbs, observe any instructions

provided by the bulb manufacturer.◀

Overview

Do not touch the bulbs

Do not touch the glass of new bulbs with

your bare hands, as even minute amounts of

contamination will burn into the bulb's surface

and reduce its service life.

Use a clean tissue, cloth or something similar,

or hold the bulb by its base.◀

1

2

3

4

5

Corner-illuminating lights

Low beams/high beams

Parking lamp, daytime running lights

Turn signal

Light-emitting diodes (LEDs)

Some items of equipment use light-emitting

diodes installed behind a cover as a light

source.

Side marker lights

These light-emitting diodes, which are related

to conventional lasers, are officially designated

as Class 1 light-emitting diodes.

Light-emitting diodes (LEDs)

Do not remove the covers

With LED headlights, all front lights and side

indicators are designed with LED technology.

Do not remove the covers, and never

stare into the unfiltered light for several hours;

otherwise, irritation of the retina could result.◀

Contact your service center in the event of a

malfunction.

Turn signal in exterior mirror

Headlight glass

The turn signals in the exterior mirrors feature

LED technology. Contact your service center

in the event of a malfunction.

Condensation can form on the inside of the ex‐

ternal lights in cool or humid weather. When

driving with the light switched on, the conden‐

sation evaporates after a short time. The head‐

light glass does not need to be changed.

190

Replacing components

Inside brake lamp

Mobility

Tail lights, bulb replacement

At a glance

Follow general instructions, refer to page 189.

24-watt bulb, HP24W.

1. Squeeze the bulb holder and pull it out.

1

2

3

4

5

6

Turn signal/brake lamp

Reversing lamp

Inside brake lamp

Rear lamp

2. Pull off the connector.

3. Replace the bulb.

4. Mount the bulb holder and the cover of the

trunk lid in reverse order.

Outside brake lamp

Rear reflector

Reversing lamp

Turn signal, outer brake, tail, and

license plate lights

Follow general instructions, refer to page 189.

16-watt bulb, W16W.

Follow general instructions, refer to page 189.

These lights feature LED technology.

1. Unscrew the bulb holder counterclockwise.

Contact your service center in the event of a

malfunction.

Lights in the trunk lid

Access to the lights

2. Pull out the bulb and replace it.

3. Mount the bulb holder and the cover of the

trunk lid in reverse order.

Changing wheels

If necessary, remove the fasteners using the

screwdriver from the onboard vehicle tool kit

and fold away the cover.

Hints

When sealants are used, an immediate wheel

change when there is a loss of tire inflation

191

Mobility

Replacing components

pressure in the event of a flat tire is unneces‐

sary.

Charging the battery

General information

Which is why no spare tire is available.

Make sure that the battery is always suffi‐

ciently charged to guarantee that the battery

remains usable for its full service life.

The tools for changing wheels are available as

accessories from your service center.

The battery may need to be charged in the fol‐

lowing cases:

Jacking points for the vehicle jack

▷

When making frequent short-distance

drives.

▷

If the vehicle is not used for prolonged pe‐

riods, longer than a month.

Hints

Do not connect charging devices to the

12 volt socket in the vehicle

The jacking points for the vehicle jack are lo‐

cated at the positions shown.

Do not connect battery chargers to the fac‐

tory-installed 12 volt sockets in the vehicle as

this may damage the vehicle battery due to an

increased power consumption.◀

Vehicle battery

Starting aid terminals

Maintenance

The battery is maintenance-free.

In the vehicle, only charge the battery via the

starting aid terminals, refer to page 196, in the

engine compartment with the engine off.

The added amount of acid is sufficient for the

service life of the battery.

Power failure

Further information about the battery can be

obtained from your service center.

After a temporary power loss, some equipment

needs to be newly initialized or individual set‐

tings updated, e. g.:

Battery replacement

▷

Seat, mirror, and steering wheel memory:

store the positions again.

Use approved vehicle batteries only

Only use vehicle batteries that have been

approved for your vehicle by the manufacturer;

otherwise, the vehicle could be damaged and

systems or functions may not be fully availa‐

ble.◀

▷

Time: update.

Date: update.

Glass sunroof: initialize the system, refer to

page 47.

After a battery replacement, have the battery

registered on the vehicle by the service center

to ensure that all comfort features are fully

available and that any Check Control mes‐

sages of these comfort features are no longer

displayed.

Disposing of old batteries

Have old batteries disposed of by your

service center or bring them to a recy‐

cling center.

192

Replacing components

Mobility

Maintain the battery in an upright position for

transport and storage. Secure the battery so

that it does not tip over during transport.

Information on the fuse types and locations is

found on a separate sheet.

Fuses

Hints

Replacing fuses

Never attempt to repair a blown fuse and

do not replace a defective fuse with a substi‐

tute of another color or amperage rating; this

could lead to a circuit overload, ultimately re‐

sulting in a fire in the vehicle.◀

Plastic tweezers and information on the fuse

types and locations are stored in the fuse box

in the trunk.

In the glove compartment

Push the handle up, arrow 1, and open the lid,

arrow 2.

In the trunk

Open the cover on the right side trim, arrow.

193

Mobility

Breakdown assistance

Hints

Vehicle features and options

Emergency Request not guaranteed

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

For technical reasons, the Emergency

Request cannot be guaranteed under unfavor‐

able conditions.◀

Overview

Hazard warning flashers

SOS button in the roofliner

Requirements

▷

The SIM card integrated in the vehicle has

been activated.

The button is located in the center console.

▷

The radio-ready state is switched on.

The Assist system is functional.

Initiating an Emergency Request

1. Press the cover briefly to open it.

Intelligent Emergency

Request

2. Press the SOS button until the LED at the

button lights up green.

The concept

In case of an emergency, an Emergency Re‐

quest can be made through this system.

▷

The LED lights up green: an Emergency

Request was initiated.

If a cancel prompt appears on the display,

the Emergency Request can be aborted.

General information

Only press the SOS button in an emergency.

If the situation allows, wait in your vehicle

until the voice connection has been estab‐

lished.

▷

The LED flashes green when a connection

to the BMW Response Center has been

established.

194

Breakdown assistance

Mobility

When the emergency request is received

at the BMW Response Center, the BMW

Response Center contacts you and takes

further steps to help you.

First aid kit

Note

Some of the articles have a limited service life.

Even if you are unable to respond, the

BMW Response Center can take further

steps to help you under certain circum‐

stances.

Check the expiration dates of the contents

regularly and replace any expired items

promptly.

For this, data are transmitted to the BMW

Response Center which serve to deter‐

mine the necessary rescue measures. E. g.

the current position of the vehicle, if it can

be established.

Storage

The first aid kit is located in the insert in the

rear seat backrest.

1. Pull the release in the direction of the ar‐

row, and remove the insert from the front. If

necessary, when pulling the release, press

against the insert.

▷

If the LED is flashing green, but the BMW

Response Center can no longer be heard

via the speaker, you can nevertheless still

be heard at the BMW Response Center.

Initiating an Emergency Request

automatically

Under certain conditions, an Emergency Re‐

quest is automatically initiated immediately af‐

ter a severe accident. Automatic Collision Noti‐

fication is not affected by pressing the SOS

button.

2. Remove the first aid kit.

Warning triangle

When replacing the insert, place both pins into

the rail at the bottom and press the insert back

in place until a 'click' is heard. Ensure that the

rear seat backrest upholstery is not damaged.

The warning triangle is located on the inside of

the trunk lid.

To remove, loosen the bracket.

195

Mobility

Breakdown assistance

Jump-starting

General information

If the battery is discharged, the engine can be

started using the battery of another vehicle

and two jumper cables. Only use jumper ca‐

bles with fully insulated clamp handles.

Hints

The so-called starting aid terminal in the en‐

gine compartment acts as the battery's posi‐

tive terminal.

Do not touch live parts

To avoid the risk of potentially fatal in‐

jury, always avoid all contact with electrical

components while the engine is running.◀

To prevent personal injury or damage to both

vehicles, adhere strictly to the following proce‐

dure.

Preparation

Bodywork contact between vehicles

Make sure that there is no contact be‐

tween the bodywork of the two vehicles; other‐

wise, there is a danger of short circuits.◀

The body ground or a special nut acts as the

battery negative terminal.

1. Check whether the battery of the other ve‐

hicle has a voltage of 12 volts. This infor‐

mation can be found on the battery.

Connecting the cables

1. Pull off the lid of the BMW starting aid ter‐

minal.

2. Switch off the engine of the assisting vehi‐

cle.

2. Attach one terminal clamp of the positive

jumper cable to the positive terminal of the

battery, or to the corresponding starting

aid terminal of the vehicle providing assis‐

tance.

3. Switch off any electronic systems/power

consumers in both vehicles.

Starting aid terminals

3. Attach the terminal clamp on the other end

of the cable to the positive terminal of the

battery, or to the corresponding starting

aid terminal of the vehicle to be started.

Connecting order

Connect the jumper cables in the correct

order to prevent risk of injury from arcing.◀

4. Attach one terminal clamp of the negative

jumper cable to the negative terminal of

the battery, or to the corresponding engine

or body ground of assisting vehicle.

5. Attach the second terminal clamp to the

negative terminal of the battery, or to the

196

Breakdown assistance

Mobility

corresponding engine or body ground of

the vehicle to be started.

Follow the towing instructions

Follow all towing instructions; otherwise,

vehicle damage or accidents may occur.◀

Starting the engine

Never use spray fluids to start the engine.

▷

Make sure that the ignition is switched on;

otherwise, the low beams, tail lights, turn

signals, and wipers may be unavailable.

1. Start the engine of the assisting vehicle

and let it run for several minutes at an in‐

creased idle speed.

▷

Do not tow the vehicle with the rear axle

tilted, as the front wheels could turn.

2. Start the engine of the vehicle that is to be

started in the usual way.

When the engine is stopped, there is no

power assist. Consequently, more force

needs to be applied when braking and

steering.

If the first starting attempt is not success‐

ful, wait a few minutes before making an‐

other attempt in order to allow the dis‐

charged battery to recharge.

▷

Larger steering wheel movements are re‐

quired.

3. Let both engines run for several minutes.

The towing vehicle must not be lighter

than the vehicle being towed; otherwise,

it will not be possible to control the vehi‐

cle's response.

4. Disconnect the jumper cables in the re‐

verse order.

Check the battery and recharge if needed.

Tow truck

Tow-starting and towing

Note

Tow-starting and towing

For tow-starting or towing, switch off the

Intelligent Safety systems; otherwise malfunc‐

tions of the individual braking systems might

lead to accidents.◀

Have your vehicle transported with a tow truck

with a so-called lift bar or on a flat bed.

Manual transmission

Do not lift the vehicle

Observe before towing your vehicle

Do not lift the vehicle by the tow fitting or

body and chassis parts; otherwise, damage

may result.◀

Gearshift lever in neutral position.

Towing

When the parking brake is blocked

The parking brake cannot be released

manually.

Do not tow the vehicle with the parking brake

blocked, or the vehicle can be damaged.

Contact your service center.◀

197

Mobility

Breakdown assistance

▷

Switch on the hazard warning system, de‐

pending on local regulations.

M double-clutch transmission:

transporting your vehicle

If the electrical system has failed, clearly

identify the vehicle being towed by placing

a sign or a warning triangle in the rear win‐

dow.

Note

Your vehicle is not permitted to be towed.

Therefore, contact a service center in the

event of a breakdown.

Tow bar

Do not have the vehicle towed

The tow fittings used should be on the same

side on both vehicles.

Have your vehicle transported on a load‐

ing platform only; otherwise, damage may oc‐

cur.◀

Should it prove impossible to avoid mounting

the tow bar at an offset angle, please observe

the following:

Tow truck

▷

Maneuvering capability is limited going

around corners.

▷

The tow bar will generate lateral forces if it

is secured with an offset.

Tow rope

When starting to tow the vehicle, make sure

that the tow rope is taut.

To avoid jerking and the associated stresses

on the vehicle components when towing, al‐

ways use nylon ropes or nylon straps.

Do not lift the vehicle

Do not lift the vehicle by the tow fitting or

body and chassis parts; otherwise, damage

may result.◀

Tow fitting

The screw-in tow fitting should always be car‐

ried in the vehicle.

Use tow fitting located in the front only for po‐

sitioning the vehicle.

The tow fitting can be screwed in at the front

or rear of the BMW.

Towing other vehicles

Hints

Light towing vehicle

The towing vehicle must not be lighter

than the vehicle being towed; otherwise, it will

not be possible to control the vehicle's re‐

sponse.◀

Attaching the tow bar/tow rope correctly

The tow fitting is located in the onboard vehi‐

cle tool kit under the cargo floor panel.

Attach the tow bar or tow rope to the tow

fitting; connecting it to other vehicle parts may

cause damage.◀

198

Breakdown assistance

Mobility

Tow fitting, information on use

4. Have the vehicle tow-started with the

clutch pedal pressed and slowly release

the pedal. After the engine starts, immedi‐

ately press on the clutch pedal again.

▷

Use only the tow fitting provided with

the vehicle and screw it all the way in.

▷

Use the tow fitting for towing on paved

roads only.

5. Stop at a suitable location, remove the tow

bar or rope, and switch off the hazard

warning system.

Avoid lateral loading of the tow fitting, e.g.,

do not lift the vehicle by the tow fitting.

6. Have the vehicle checked.

Otherwise, damage to the tow fitting and the

vehicle can occur.◀

Screw thread for tow fitting

Push out the cover by pressing on the top

edge.

Tow-starting

M double-clutch transmission

Do not tow-start the vehicle.

Tow-starting the engine is not possible due to

the transmission.

Have the cause of the starting problems fixed.

Manual transmission

If possible, do not tow-start the vehicle but

start the engine by jump-starting, refer to

page 196. If the vehicle is equipped with a cat‐

alytic converter, only tow-start while the en‐

gine is cold.

1. Switch on the hazard warning system and

comply with local regulations.

2. Ignition, refer to page 63, on.

3. Engage third gear.

199

Mobility

Care

Cleaning sensors/camera lenses with

high-pressure washers

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

When using high-pressure washers, do not

spray the sensors and camera lenses on the

outside of the vehicle for long periods and

maintain a distance of at least 12 in/30 cm.◀

Automatic car washes

Hints

Do not use high pressure washing sys‐

tems

Car washes

With washing systems operating at high pres‐

sures and nozzle positions close to the win‐

dows, drops of water can penetrate.◀

General information

Regularly remove foreign objects such as

leaves in the area below the windshield when

the hood is raised.

Note the following:

▷

Give preference to cloth car washes or

those that use soft brushes in order to

avoid paint damage.

Wash your vehicle frequently, particularly in

winter. Intense soiling and road salt can dam‐

age the vehicle.

▷

Make sure that the wheels and tires are not

damaged by the transport mechanisms.

Hints

Fold in the exterior mirrors; otherwise, they

may be damaged, depending on the width

of the vehicle.

Steam jets or high-pressure washers

When using steam jets or high-pressure

washers, hold them a sufficient distance away

and use a maximum temperature of

140 ℉/60 ℃.

▷

Deactivate the rain sensor, refer to

page 70, to avoid unintentional wiper acti‐

vation.

In some cases, an unintentional alarm can

be triggered by the interior motion sensor

of the alarm system. Follow the instruc‐

tions on avoiding an unintentional alarm,

refer to page 45.

If the vehicle has a glass sunroof, ensure that a

distance of at least 31.5 inches/80 cm is main‐

tained. Holding them too close or using exces‐

sively high pressures or temperatures can

cause damage or preliminary damage that may

then lead to long-term damage.

Guide rails in car washes

Follow the user's manual for the high-pressure

washer.◀

Avoid car washes with guide rails higher

than 4 in/10 cm; otherwise, the vehicle body

could be damaged.◀

200

Care

Mobility

▷

After approx. 15 minutes.

Before driving into a car wash

In order to ensure that the vehicle can roll in a

car wash, take the following steps:

Headlights

▷

Do not rub dry and do not use abrasive or

acidic cleansers.

Manual transmission:

1. Drive into the car wash.

2. Shift to neutral.

▷

Soak areas that have been dirtied e. g.,

from insects, with shampoo and wash off

with water.

3. Switch the engine off.

4. Switch on the ignition.

M double-clutch transmission:

▷

Thaw ice with de-icing spray; do not use an

ice scraper.

1. Drive into the car wash.

After washing the vehicle

2. Engage selector lever position N.

3. Switch the engine off.

After washing the vehicle, apply the brakes

briefly to dry them; otherwise, braking action

can be reduced and corrosion of the brake

discs can occur.

In this way, the ignition remains switched

on, and a Check-Control message is dis‐

played.

Completely remove all residues on the win‐

dows, to minimize loss of visibility due to

smearing and to reduce wiper noises and

wiper blade wear.

Do not turn off the ignition in the car

wash

Do not turn off the ignition in the car wash;

otherwise, the transmission position P is

engaged and damages can result.◀

Vehicle care

The vehicle cannot be locked from the outside

when in selector lever position N. A signal

sounds when an attempt is made to lock the

vehicle.

Car care products

BMW recommends using care and cleaning

products from BMW, since these have been

tested and approved.

To start the engine with manual transmission:

Car care and cleaning products

1. Press on the clutch pedal.

2. Press the Start/Stop button.

Follow the instructions on the container.

When cleaning the interior, open the doors or

windows.

To start the engine with a M double clutch

transmission:

Only use products intended for cleaning vehi‐

cles.

1. Depress the brake pedal.

2. Press the Start/Stop button.

Cleansers can contain substances that are

dangerous and harmful to your health.◀

Pressing the Start/Stop button without step‐

ping on the brake turns the ignition off.

Vehicle paint

Transmission position

Regular care contributes to driving safety and

value retention. Environmental influences in

areas with elevated air pollution or natural con‐

taminants, such as tree resin or pollen can af‐

fect the vehicle's paintwork. Tailor the fre‐

Transmission position P is engaged automati‐

cally:

▷

When the ignition is switched off.

201

Mobility

Care

quency and extent of your car care to these

influences.

Damage from Velcro® fasteners

Open Velcro® fasteners on pants or

other articles of clothing can damage the seat

covers. Ensure that any Velcro® fasteners are

closed.◀

Aggressive substances such as spilled fuel, oil,

grease or bird droppings, must be removed im‐

mediately to prevent the finish from being al‐

tered or discolored.

Only use respectively approved cleaning and

care products for vehicles with matte finish.

Suitable care products for matte finishes are

available from the service center.

Caring for special components

Light-alloy wheels

When cleaning the vehicle, use only neutral

wheel cleaners having a pH value from 5 to 9.

Do not use abrasive cleaning agents or steam

jets above 140 ℉/60 ℃. Follow the manufac‐

turer's instructions.

Leather care

Remove dust from the leather often, using a

cloth or vacuum cleaner.

Otherwise, particles of dust and road grime

chafe in pores and folds, and lead to increased

wear and premature degradation of the leather

surface.

Aggressive, acidic or alkaline cleaning agents

can destroy the protective layer of adjacent

components, such as the brake disk.

Chrome surfaces

To guard against discoloration, such as from

clothing, provide leather care roughly every

two months.

Carefully clean components such as the radia‐

tor grille or door handles with an ample supply

of water, possibly with shampoo added, partic‐

ularly when they have been exposed to road

salt.

Clean light-colored leather more frequently be‐

cause soiling on such surfaces is substantially

more visible.

Use leather care products; otherwise, dirt and

grease will gradually break down the protective

layer of the leather surface.

Rubber components

Aside from water, treat only with rubber

cleansers.

Suitable care products are available from the

service center.

When cleaning rubber seals, do not use any

silicon-containing car care products in order to

avoid damage or noises.

Upholstery material care

Vacuum regularly with a vacuum cleaner.

Fine wood parts

If upholstery is very dirty, e.g., with beverage

stains, use a soft sponge or microfiber cloth

with a suitable interior cleaner.

Clean fine wood facing and fine wood compo‐

nents only with a moist rag. Then dry with a

soft cloth.

Clean the upholstery down to the seams using

large sweeping motions. Avoid rubbing the

material vigorously.

Plastic components

These include:

▷

Imitation leather surfaces.

Roofliner.

Lamp lenses.

Instrument cluster cover.

202

Care

Mobility

▷

Matt black spray-coated components.

Painted parts in the interior.

If the floor carpets are very dirty, clean with a

microfiber cloth and water or a textile cleaner.

To prevent matting of the carpet, rub back and

forth in the direction of travel only.

Clean with a microfiber cloth.

Dampen cloth lightly with water.

Do not soak the roofliner.

Sensor/camera lenses

To clean sensors and camera lenses, use a

cloth moistened with a small amount of glass

detergent.

No cleansers that contain alcohol or sol‐

vents

Do not use cleansers that contain alcohol or

solvents, such as lacquer thinners, heavy-duty

grease removers, fuel, or such; this could lead

to surface damage.◀

Displays/monitors

Cleaning displays and screens

Do not use any chemical or household

cleaning agents; otherwise, surfaces can be af‐

fected.◀

Safety belts

Dirty belt straps impede the reeling action and

thus have a negative impact on safety.

Keeping out moisture

Chemical cleaning

Keep all fluids and moisture away from

the unit; otherwise, electrical components can

be damaged.◀

Do not clean chemically; this can destroy

the webbing.◀

Use only a mild soapy solution, with the safety

belts clipped into their buckles.

Avoid pressure

Avoid pressing too hard when cleaning

and do not use abrasive materials; otherwise,

damage can result.◀

Do not allow the reels to retract the safety

belts until they are dry.

Clean with a clean, antistatic microfiber cloth.

Carpets and floor mats

No objects in the area around the pedals

Long-term

Keep floor mats, carpets, and any other

objects out of the pedal area; otherwise, the

function of the pedals could be impeded while

driving and create the risk of an accident.

When the vehicle is shut down for longer than

three months, special measures must be

taken. Additional information is available from

the service center.

Do not place additional floor mats over existing

mats or other objects.

Only use floor mats that have been approved

for the vehicle and can be properly attached to

floor.

Ensure that the floor mats are securely fas‐

tened again after they were removed for clean‐

ing, e.g.◀

Floor mats can be removed from the car's inte‐

rior for cleaning.

203

Mobility for Your BMW M6 4 Door Third Generation (2012-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals