Get Mobility -> Care Guide for BMW M6 4 Door Third Generation (2012-2019)

Mobility

Care

Cleaning sensors/camera lenses with

high-pressure washers

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and

systems. The respectively applicable country

provisions must be observed when using the

respective features and systems.

When using high-pressure washers, do not

spray the sensors and camera lenses on the

outside of the vehicle for long periods and

maintain a distance of at least 12 in/30 cm.◀

Automatic car washes

Hints

Do not use high pressure washing sys‐

tems

Car washes

With washing systems operating at high pres‐

sures and nozzle positions close to the win‐

dows, drops of water can penetrate.◀

General information

Regularly remove foreign objects such as

leaves in the area below the windshield when

the hood is raised.

Note the following:

▷

Give preference to cloth car washes or

those that use soft brushes in order to

avoid paint damage.

Wash your vehicle frequently, particularly in

winter. Intense soiling and road salt can dam‐

age the vehicle.

▷

Make sure that the wheels and tires are not

damaged by the transport mechanisms.

Hints

Fold in the exterior mirrors; otherwise, they

may be damaged, depending on the width

of the vehicle.

Steam jets or high-pressure washers

When using steam jets or high-pressure

washers, hold them a sufficient distance away

and use a maximum temperature of

140 ℉/60 ℃.

▷

Deactivate the rain sensor, refer to

page 70, to avoid unintentional wiper acti‐

vation.

In some cases, an unintentional alarm can

be triggered by the interior motion sensor

of the alarm system. Follow the instruc‐

tions on avoiding an unintentional alarm,

refer to page 45.

If the vehicle has a glass sunroof, ensure that a

distance of at least 31.5 inches/80 cm is main‐

tained. Holding them too close or using exces‐

sively high pressures or temperatures can

cause damage or preliminary damage that may

then lead to long-term damage.

Guide rails in car washes

Follow the user's manual for the high-pressure

washer.◀

Avoid car washes with guide rails higher

than 4 in/10 cm; otherwise, the vehicle body

could be damaged.◀

200

Care

Mobility

▷

After approx. 15 minutes.

Before driving into a car wash

In order to ensure that the vehicle can roll in a

car wash, take the following steps:

Headlights

▷

Do not rub dry and do not use abrasive or

acidic cleansers.

Manual transmission:

1. Drive into the car wash.

2. Shift to neutral.

▷

Soak areas that have been dirtied e. g.,

from insects, with shampoo and wash off

with water.

3. Switch the engine off.

4. Switch on the ignition.

M double-clutch transmission:

▷

Thaw ice with de-icing spray; do not use an

ice scraper.

1. Drive into the car wash.

After washing the vehicle

2. Engage selector lever position N.

3. Switch the engine off.

After washing the vehicle, apply the brakes

briefly to dry them; otherwise, braking action

can be reduced and corrosion of the brake

discs can occur.

In this way, the ignition remains switched

on, and a Check-Control message is dis‐

played.

Completely remove all residues on the win‐

dows, to minimize loss of visibility due to

smearing and to reduce wiper noises and

wiper blade wear.

Do not turn off the ignition in the car

wash

Do not turn off the ignition in the car wash;

otherwise, the transmission position P is

engaged and damages can result.◀

Vehicle care

The vehicle cannot be locked from the outside

when in selector lever position N. A signal

sounds when an attempt is made to lock the

vehicle.

Car care products

BMW recommends using care and cleaning

products from BMW, since these have been

tested and approved.

To start the engine with manual transmission:

Car care and cleaning products

1. Press on the clutch pedal.

2. Press the Start/Stop button.

Follow the instructions on the container.

When cleaning the interior, open the doors or

windows.

To start the engine with a M double clutch

transmission:

Only use products intended for cleaning vehi‐

cles.

1. Depress the brake pedal.

2. Press the Start/Stop button.

Cleansers can contain substances that are

dangerous and harmful to your health.◀

Pressing the Start/Stop button without step‐

ping on the brake turns the ignition off.

Vehicle paint

Transmission position

Regular care contributes to driving safety and

value retention. Environmental influences in

areas with elevated air pollution or natural con‐

taminants, such as tree resin or pollen can af‐

fect the vehicle's paintwork. Tailor the fre‐

Transmission position P is engaged automati‐

cally:

▷

When the ignition is switched off.

201

Mobility

Care

quency and extent of your car care to these

influences.

Damage from Velcro® fasteners

Open Velcro® fasteners on pants or

other articles of clothing can damage the seat

covers. Ensure that any Velcro® fasteners are

closed.◀

Aggressive substances such as spilled fuel, oil,

grease or bird droppings, must be removed im‐

mediately to prevent the finish from being al‐

tered or discolored.

Only use respectively approved cleaning and

care products for vehicles with matte finish.

Suitable care products for matte finishes are

available from the service center.

Caring for special components

Light-alloy wheels

When cleaning the vehicle, use only neutral

wheel cleaners having a pH value from 5 to 9.

Do not use abrasive cleaning agents or steam

jets above 140 ℉/60 ℃. Follow the manufac‐

turer's instructions.

Leather care

Remove dust from the leather often, using a

cloth or vacuum cleaner.

Otherwise, particles of dust and road grime

chafe in pores and folds, and lead to increased

wear and premature degradation of the leather

surface.

Aggressive, acidic or alkaline cleaning agents

can destroy the protective layer of adjacent

components, such as the brake disk.

Chrome surfaces

To guard against discoloration, such as from

clothing, provide leather care roughly every

two months.

Carefully clean components such as the radia‐

tor grille or door handles with an ample supply

of water, possibly with shampoo added, partic‐

ularly when they have been exposed to road

salt.

Clean light-colored leather more frequently be‐

cause soiling on such surfaces is substantially

more visible.

Use leather care products; otherwise, dirt and

grease will gradually break down the protective

layer of the leather surface.

Rubber components

Aside from water, treat only with rubber

cleansers.

Suitable care products are available from the

service center.

When cleaning rubber seals, do not use any

silicon-containing car care products in order to

avoid damage or noises.

Upholstery material care

Vacuum regularly with a vacuum cleaner.

Fine wood parts

If upholstery is very dirty, e.g., with beverage

stains, use a soft sponge or microfiber cloth

with a suitable interior cleaner.

Clean fine wood facing and fine wood compo‐

nents only with a moist rag. Then dry with a

soft cloth.

Clean the upholstery down to the seams using

large sweeping motions. Avoid rubbing the

material vigorously.

Plastic components

These include:

▷

Imitation leather surfaces.

Roofliner.

Lamp lenses.

Instrument cluster cover.

202

Care

Mobility

▷

Matt black spray-coated components.

Painted parts in the interior.

If the floor carpets are very dirty, clean with a

microfiber cloth and water or a textile cleaner.

To prevent matting of the carpet, rub back and

forth in the direction of travel only.

Clean with a microfiber cloth.

Dampen cloth lightly with water.

Do not soak the roofliner.

Sensor/camera lenses

To clean sensors and camera lenses, use a

cloth moistened with a small amount of glass

detergent.

No cleansers that contain alcohol or sol‐

vents

Do not use cleansers that contain alcohol or

solvents, such as lacquer thinners, heavy-duty

grease removers, fuel, or such; this could lead

to surface damage.◀

Displays/monitors

Cleaning displays and screens

Do not use any chemical or household

cleaning agents; otherwise, surfaces can be af‐

fected.◀

Safety belts

Dirty belt straps impede the reeling action and

thus have a negative impact on safety.

Keeping out moisture

Chemical cleaning

Keep all fluids and moisture away from

the unit; otherwise, electrical components can

be damaged.◀

Do not clean chemically; this can destroy

the webbing.◀

Use only a mild soapy solution, with the safety

belts clipped into their buckles.

Avoid pressure

Avoid pressing too hard when cleaning

and do not use abrasive materials; otherwise,

damage can result.◀

Do not allow the reels to retract the safety

belts until they are dry.

Clean with a clean, antistatic microfiber cloth.

Carpets and floor mats

No objects in the area around the pedals

Long-term

Keep floor mats, carpets, and any other

objects out of the pedal area; otherwise, the

function of the pedals could be impeded while

driving and create the risk of an accident.

When the vehicle is shut down for longer than

three months, special measures must be

taken. Additional information is available from

the service center.

Do not place additional floor mats over existing

mats or other objects.

Only use floor mats that have been approved

for the vehicle and can be properly attached to

floor.

Ensure that the floor mats are securely fas‐

tened again after they were removed for clean‐

ing, e.g.◀

Floor mats can be removed from the car's inte‐

rior for cleaning.

203

Mobility -> Care for Your BMW M6 4 Door Third Generation (2012-2019)

Related Topics

Mobility

Popular Owner Manuals

Latest Owner Manuals