Get CONTROLS -> Interior equipment Guide for BMW X6 4 Door Third Generation (2020-2025)

Interior equipment

CONTROLS

Interior equipment

of damage to property. Make sure that the

travel path of the respective system is clear

during programming and operation. Also fol-

low the safety information for the hand-held

transmitter.

Vehicle features and options

This chapter describes model-specific equip-

ment, systems, and functions that are currently

available, or may become available in the fu-

ture, even if they are not present in the vehicle.

Additional information:

Compatibility

Vehicle equipment, refer to page 8.

If this icon is printed on the packaging

or in the operating instructions of the

remote-controlled system, the system

is generally compatible with the integrated uni-

versal remote control.

Integrated universal remote

control

Additional questions are answered by:

Principle

▷

An authorized service center or another

qualified service center or repair shop.

The integrated universal remote control in the

interior mirror can operate remote-controlled

systems such as garage door openers, alarm

systems or locking systems.

▷

on the Internet.

HomeLink is a registered trademark of Gentex

Corporation.

For any additional questions, contact an au-

thorized service center or another qualified

service center or repair shop.

General information

The integrated universal remote control re-

places up to three different hand-held trans-

mitters. To operate the remote control, the

buttons on the interior mirror must be pro-

grammed with the desired functions.

Operating elements on the interior

mirror

Before selling the vehicle, delete the stored

functions for the sake of security.

If possible, do not install the antenna of the

remote-controlled system near metal objects

to ensure the best possible operation.

Safety information

Warning

▷

Buttons, arrow 1.

LED, arrow 2.

The operation of remote-controlled systems

with the integrated universal remote control

such as the garage door may result in injury,

for example, body parts becoming jammed in

a garage door. There is a risk of injury or risk

Hand-held transmitter of the remote-con-

trolled system, arrow 3.

294

Interior equipment

CONTROLS

Press and hold the button on the interior

mirror for approx. 2 seconds. Perform

this procedure three times.

Programming the integrated

universal remote control

If the integrated universal remote con-

trol remains nonoperational, continue

with the special features for rolling code

radio systems.

Functional requirement

The battery of the hand-held transmitter must

be fully charged at the time of programming

to ensure an optimal range of the integrated

universal remote control.

▷

LED does not illuminate green after

60 seconds: programming not com-

pleted.

Programming individual buttons

1. Park the vehicle within range of the remote-

controlled system.

Repeat steps 3 to 5.

Special feature of the rolling code

wireless system

For systems with a rolling code radio system,

the integrated universal remote control and the

system also have to be synchronized.

2. Turn on standby state.

3. Select desired button on the interior mirror:

▷

Program available button:

Press the button.

▷

Program already assigned button:

Refer to information on synchronization in the

operating instructions of the remote-controlled

system.

Press and hold the button for approx.

20 seconds.

The LED on the interior mirror will slowly

begin flashing orange.

1. Program the desired button on the interior

mirror.

4. Hold the hand-held transmitter for the

remote-controlled system approx. 1 to

12 in/2.5 to 30 cm away from the buttons

on the interior mirror.

2. Locate and press the synchronizing button

on the remote-controlled system such as

on the garage door.

You have approx. 30 seconds for the next

step.

The required distance depends on the

hand-held transmitter.

Synchronizing is easier with the aid of a

second person.

5. Press and hold the button on the hand-held

transmitter.

3. Press and hold the programmed button on

the interior mirror for approx. 3 seconds.

Canada: if programming with the hand-held

transmitter was interrupted, hold down the

interior mirror button and repeatedly press

and release the hand-held transmitter but-

ton for 2 seconds.

If necessary, repeat this step up to three

times in order to end synchronization. Once

synchronization is complete, the program-

med function will be carried out.

6. The LED can illuminate in different ways:

Operation

After programming, the remote-controlled sys-

tem can be operated with the button on the

interior mirror.

▷

The LED illuminates green: program-

ming completed.

Release button.

▷

The LED flashes green rapidly: the

hand-held transmitter was detected but

programming is not complete.

295

Interior equipment

CONTROLS

Press and hold the desired button of the re-

mote-controlled system within range until the

function is triggered.

Sockets

Principle

The socket can be used for electronic devi-

ces when the standby or drive-ready state is

switched on.

The LED on the interior mirror is continuously

illuminated green during the transmission of

the radio signal.

Deleting a button assignment

The button assignment cannot be deleted indi-

vidually.

General information

The total load of all sockets must not exceed

140 watts at 12 volts.

Press and hold the two outer buttons on

the interior mirror simultaneously for approxi-

mately 10 seconds until the LED flashes green

rapidly.

Do not damage the socket by using unsuitable

connectors.

Safety information

All stored button assignments will be deleted.

Warning

Sun visor

Devices and cables in the unfolding area of

the airbags such as portable navigation devi-

ces can hinder the unfolding of the airbag or

be thrown around in the car's interior while

unfolding. There is a risk of injury and risk

of property damage. Make sure that devices

and cables are not in the airbag's area of

unfolding.

Glare shield

Fold the sun visor down or up.

Glare shield from the side

Folding the sun visor out

1. Fold the sun visor down.

2. Detach it from the holder and swing it to-

ward the side window.

Warning

Battery chargers that charge the vehicle bat-

tery via sockets or cigarette lighters in the ve-

hicle may overload or damage the 12 V elec-

trical system. There is a risk of injury or risk

of damage to property. Only connect battery

chargers for the vehicle battery to the jump-

start terminals in the engine compartment.

3. Shift it back to the desired position.

Folding the sun visor in

Proceed in the reverse order to close the sun

visor.

Vanity mirror

A vanity mirror is located in the sun visor be-

hind a cover.

Warning

If metal objects fall or are plugged into elec-

tronic interfaces, e.g., sockets or USB ports,

these objects can cause a short circuit and

destroy the interface. There is a risk of injury

and risk of property damage. Make sure to

296

Interior equipment

CONTROLS

prevent metal objects from falling or being

plugged into electronic interfaces. Insert the

cigarette lighter or socket cover again after

using the socket.

In the cargo area

Front center console

A socket is located on the right side in the

cargo area. Unfold the cover.

USB port

Press on the cover.

General information

Follow the information regarding the connec-

tion of mobile devices to the USB port in the

section on USB connections.

Additional information:

USB connection, see Owner's Manual for Nav-

igation, Entertainment, Communication;

Safety information

A socket is located between the cup holders in

one of the marked positions. Detach the cover.

Warning

If metal objects fall or are plugged into elec-

tronic interfaces, e.g., sockets or USB ports,

these objects can cause a short circuit and

destroy the interface. There is a risk of injury

and risk of property damage. Make sure to

prevent metal objects from falling or being

plugged into electronic interfaces. Insert the

cigarette lighter or socket cover again after

using the socket.

Rear center console

A socket is located in the center console.

Detach the cover.

297

Interior equipment

CONTROLS

In the center armrest

A USB port is located in the center console at

one of the marked positions.

A USB port is located in the center armrest.

Properties:

▷

USB port Type A.

▷

USB port Type C.

For charging mobile devices and for data

transfer.

For charging mobile devices.

Charge current: max. 3 A.

▷

Charge current: max. 1.5 A.

In the center console

Travel & Comfort system

NOTICE

General information

The front seat backrests have mounts and var-

ious connection options:

Objects in the storage compartment, e.g.,

large USB connectors, may block or damage

the cover when it is being opened or closed.

There is a risk of property damage. Make

sure that the area of movement of the cover

is clear while opening and closing it.

▷

Mounts for attaching optional accessories,

e.g., universal holders for tablets or coat

hangers.

▷

USB ports.

Properties of the USB ports:

▷

USB port Type C.

For charging mobile devices.

Charge current: maximum 3 A / 45 W per

seat.

For more information, contact an authorized

service center or another qualified service cen-

ter or repair shop.

Press on the cover.

298

Interior equipment

CONTROLS

Overview

Safety information

Warning

When charging a Qi-compatible device in the

wireless charging tray, any metal objects on

the tray together with the device can become

very hot. Storage media or electronic cards,

e.g., chip cards, cards with magnetic strips, or

cards for transmitting signals, may not func-

tion correctly when placed together on the

tray with the device. There is a risk of injury

and risk of property damage. When charging

mobile devices, make sure there are no ob-

jects on the tray together with the device.

The mounts for attaching optional accessories

are located behind the marked covers, as are

the USB ports.

Attaching optional accessories

1. Slide the cover all the way to the side.

Overview

Tray across in the center console:

2. Mount the optional accessories, refer to As-

sembly Instructions.

1

LED

2

Storage area

Wireless charging tray

Tray on the left in the center console:

Principle

The wireless charging tray is used to wirelessly

charge Qi-certified smartphones.

General information

When inserting the smartphone to be charged,

make sure that there is nothing between the

smartphone to be charged and the wireless

charging tray.

1

LED

The charging process is shown by the

charge indicator on the control display.

2

Storage area

299

Interior equipment

CONTROLS

Functional requirements

Forgotten warning

▷

The smartphone to be charged must be Qi-

certified.

General information

A warning may be issued if a Qi-certified

smartphone was forgotten in the wireless

charging tray when leaving the vehicle.

▷

Standby state is switched on.

Smartphone must not exceed maximum di-

mensions of approx. 6.0 x 3.1 x 0.7 in/154.5

x 80 x 18 mm.

The forgotten warning is displayed in the in-

strument cluster.

▷

Protective sleeves and covers must be suit-

able for wireless charging.

Enable/Disable Forgotten Warning

The smartphone to be charged is located

in the center of the tray. The smartphone

display is facing up.

1.

Apps menu

2. "Vehicle"

3. "System settings"

4. "Wireless charging tray"

5. "Mobile phone reminder"

Inserting a smartphone

1. Open the tray cover.

2. Place the smartphone in the middle of the

tray, with the display facing up.

System limits

The charge current may be reduced or charg-

ing may be temporarily interrupted in the wire-

less charging tray in the following situations:

3. Close the tray cover.

LED displays

▷

Due to excessive temperatures on the tray

and smartphone.

Color Meaning

If there are objects between the smart-

phone and wireless charging tray.

Blue

Smartphone is charging.

The blue LED continues to illumi-

nate when the Qi-capable smart-

phone is fully charged.

If storage media or electronic cards,

e.g., chip cards, cards with magnetic

stripes, or cards for signal transmission, are

located between the smartphone and wire-

less charging tray.

Or-

Smartphone is not charging.

ange

Temperature on the smartphone

may be too high, or foreign object

may be in charging tray.

▷

Due to protective sleeves and covers that

exceed a thickness of 0.07 in/2 mm

Red

Smartphone is not charging.

Due to protective sleeves and covers made

of unsuitable material, e.g., with magnetic

parts.

Contact an authorized service center

or another qualified service center or

repair shop.

▷

Due to add-on parts for the smartphone,

e.g., holders.

By configuring the smartphone settings,

e.g., for charging. Follow the instructions

given on the control display and smart-

phone, as applicable.

300

CONTROLS -> Interior equipment for Your BMW X6 4 Door Third Generation (2020-2025)

Related Topics

CONTROLS

Popular Owner Manuals

Latest Owner Manuals