Get Technical Data Guide for Citroen C4 Grand Picasso SUV First Generation (2006-2013)

P R A C T I C A L I N F O R M AT I O N

Removing a wheel

 Park the vehicle on level, stable

and non-slippery ground. Apply

the parking brake (a message

and a warning lamp appear on

the instrument panel).

 Detach the trim using the remov-

ing tool 4, pulling in the area of

the valve.

 Slacken the wheel bolts. For ve-

hicles with alloy wheels, undo

the security bolts using the secu-

rity socket 6.

 Position the jack under the vehi-

cle, at the jacking point A closest

to the wheel to be changed.

 Unwind the jack 5 until its brack-

et is in contact with the ground.

Make sure that the jack is verti-

cal under the jacking point used.

 Continue to extend the jack so

as to raise the vehicle.

For vehicles with alloy wheels,

insert the trim removing tool 1

into the recess in the central trim

and lever it off.

For vehicles with alloy wheels

that have visible bolts, remove

the chrome covers using the re-

moving tool 2.

Switch off the ignition and engage

ﬁrst gear or reverse gear depend-

ing on the slope (position P if an

automatic gearbox, D or R if a

6-speed electronic gearbox).

 Use a chock to secure the vehi-

cle more safely. Place the chock

9 in front of the wheel that is op-

posite the wheel affected.

 Undo the wheel bolts and remove

the wheel.

Before any operation of this

sort, it is advisable to deac-

tivate your pneumatic sus-

pension.

Copyright CITROEN compiled by C4owners.org

172

P R A C T I C A L I N F O R M AT I O N

Temporary use spare wheel

Fitting a wheel

Spare wheel dimensions

Position the wheel with the aid of

the centring guide 3

Do up the 3 bolts by hand, then

remove the centring guide 3

Position the 4th bolt.

Pre-tighten the wheel bolts,

using the wheelbrace 4

Retract the jack 5 and disengage it.

Tighten the wheel bolts, using

If your spare wheel has dimensions

different from those of the normal

vehicle wheels (identiﬁed by a la-

bel), it is imperative to use the spare

wheel only temporarily, to drive with

caution, not to exceed 50 mph

(80 km/h) and to have the tyre re-

paired and the normal wheel reﬁtted

as soon as possible.

the wheelbrace 4

Ensure that the tyre pressure is

correct.

If your vehicle is equipped with a

spare wheel for temporary use only,

when ﬁtting this it is normal to observe

that the wheel bolts do not come to

bear directly on the wheel rim.

The spare wheel is secured by the

conical tapering of the wheel bolt’s

shaft.

Tyre pressures

These are indicated on the la-

bel on the front left-hand door

pillar (see section "Technical Data -

§ Identiﬁcation markings").

Under-inﬂation detection

Wheels with under-inﬂation detec-

tion have tyre pressure sensors.

Have repairs to them carried out by

a CITROËN dealer. The spare wheel

does not have a sensor.

When reﬁtting the original wheel, en-

sure that the wheel bolts and wash-

ers are clean and in good condition.

The wheel bolts are speciﬁc

to each type of wheel.

Security bolts (alloy wheels)

Each wheel may be equipped with

one security bolt.

To remove it:

 Remove its protective cover us-

ing of the tool for removing the

chrome covers 2.

If new wheels are ﬁtted, check

with your CITROËN dealer that the

wheel bolts are compatible with the

new wheels.

Note: take care to note down the

code number on the head of the

security bolt socket. This will ena-

XI

 Use the security bolt socket 6

with the wheelbrace 4.

Copyright CITRO

E

^{ble you to obtain a replacement se}e^-rs.org

curity bolt socket from a CITROËN

dealer.

173

P R A C T I C A L I N F O R M AT I O N

Temporary use spare wheel

Fitting a wheel

Spare wheel dimensions

Position the wheel with the aid of

the centring guide 3

Do up the 3 bolts by hand, then

remove the centring guide 3

Position the 4th bolt.

Pre-tighten the wheel bolts,

using the wheelbrace 4

Retract the jack 5 and disengage it.

Tighten the wheel bolts, using

If your spare wheel has dimensions

different from those of the normal

vehicle wheels (identiﬁed by a la-

bel), it is imperative to use the spare

wheel only temporarily, to drive with

caution, not to exceed 50 mph

(80 km/h) and to have the tyre re-

paired and the normal wheel reﬁtted

as soon as possible.

the wheelbrace 4

Ensure that the tyre pressure is

correct.

If your vehicle is equipped with a

spare wheel for temporary use only,

when ﬁtting this it is normal to observe

that the wheel bolts do not come to

bear directly on the wheel rim.

The spare wheel is secured by the

conical tapering of the wheel bolt’s

shaft.

Tyre pressures

These are indicated on the la-

bel on the front left-hand door

pillar (see section "Technical Data -

§ Identiﬁcation markings").

Under-inﬂation detection

Wheels with under-inﬂation detec-

tion have tyre pressure sensors.

Have repairs to them carried out by

a CITROËN dealer. The spare wheel

does not have a sensor.

When reﬁtting the original wheel, en-

sure that the wheel bolts and wash-

ers are clean and in good condition.

The wheel bolts are speciﬁc

to each type of wheel.

Security bolts (alloy wheels)

Each wheel may be equipped with

one security bolt.

To remove it:

 Remove its protective cover us-

ing of the tool for removing the

chrome covers 2.

If new wheels are ﬁtted, check

with your CITROËN dealer that the

wheel bolts are compatible with the

new wheels.

Note: take care to note down the

code number on the head of the

security bolt socket. This will ena-

XI

 Use the security bolt socket 6

with the wheelbrace 4.

Copyright CITRO

E

^{ble you to obtain a replacement se}e^-rs.org

curity bolt socket from a CITROËN

dealer.

173

P R A C T I C A L I N F O R M AT I O N

Dipped beam headlamps

CHANGING A BULB

In some climatic conditions (e.g.

low temperature or humidity), the

presence of misting on the internal

surface of the glass of the head-

lamps and rear lamps is normal;

it disappears after the lamps have

been on for a few minutes.

Procedure for replacing a faulty bulb

with a new bulb without the use of

tools.

Front lamps

Model with halogen headlamps

The headlamps are ﬁtted

with polycarbonate glass

with a protective coating:

 do not clean them using a

dry or abrasive cloth, nor

with a detergent or solvent

product,

 Remove the rubber cover.

 use a sponge and soapy water,

 Rotate the bulb-holder a quarter

turn anti-clockwise and remove it

from its housing.

 when using a high pressure

washer on persistent marks, do

not direct at the lamps or their

outlines for too long, so as not

to damage their coating and

their seals.

 Do not touch the bulb directly

with your ﬁngers, use lint-free

cloths.

 Replace the faulty bulb.

 Reposition the bulb-holder by

pushing it in, tightening it by a

quarter turn clockwise.

1. Dipped beams (H7-55 W)

2. Main beams (H1-55 W)

3. Sidelamps (H6 W-6 W)

4. Direction indicators

(H21-21 W)

 Reﬁt the rubber cover.

Changing a halogen bulb should

only be done after the headlamp

has been switched off for a few

minutes (risk of serious burns).

XI

It is imperative to use only anti-

ultraviolet (UV) type bulbs in order

not to damage the headlamp.

CI

T

ROEN compiled by C4owners.org

174

P R A C T I C A L I N F O R M AT I O N

Main beam headlamps

S id e la m p s

Direction indicators

The direction indicator bulb is located

underneath the main beam bulb.

 Remove the rubber cover.



Pull on the bulb-holder to remove it.

 Replace the faulty bulb.

 Reposition the bulb-holder in the

bracket and push it in.

 Reﬁt the rubber cover.

 Remove the rubber cover.

 Detach the clips by lowering

 Rotate the bulb-holder a quarter

turn anti-clockwise.

 Remove it from its housing.

 Replace the faulty bulb.

 Reposition the bulb-holder.

them on each side of the bulb.

Pull on the bulb-holder to remove it.



 Replace the faulty bulb.

 Push the bulb-holder back into

its housing.

 Reattach the clips.

 Reﬁt the rubber cover.

 Rotate it a quarter turn clockwise

to reposition in its housing.

XI

Copyright CITROEN compiled by C4owners.org

175

P R A C T I C A L I N F O R M AT I O N

Integrated direction indicator

side repeaters

Model with Xenon headlamps

and directional headlamps

Dual-function Xenon headlamps

(dipped/main beam)

If the headlamp bears this

symbol, any operation to

change the Xenon dual-

function directional head-

lamp (D1S-35 W) must be carried

out by professionals (risk of elec-

trocution).

Consult a CITROËN dealer.

It is recommended to change both

bulbs at the same time if one of

them is faulty.

To change the repeater, press down-

wards ﬁrmly on the zone indicated

by the arrow, then pull the repeater.

Repeaters can be obtained from a

CITROËN dealer.

1. Dual-function Xenon head-

lamps (dipped/main beam)

2. Additional main beams

(H7-55 W)

3. Sidelamps (H6 W-6 W)

Additional main beams

 Remove the rubber cover.

 Rotate the bulb-holder a quarter

turn anti-clockwise and remove it

from its housing.

(see previous page)

 Replace the faulty bulb.

4. Direction indicators

(H21-21 W)

(see previous page)

 Reposition the bulb-holder by

pushing it in, tightening it by a

quarter turn clockwise.

 Reﬁt the rubber cover.

XI

When using a high-pres-

sure washer on persistent

marks, do not direct the jet

at the lamps or their edges for too

long, so as to avoid damaging their

protective coating and seals.

CI

T

ROEN compiled by C4owners.org

176

P R A C T I C A L I N F O R M AT I O N

Front foglamps (H11-55 W)

Rear foglamp (P21 W)

 Insert the key in the notch A, tilt-

ing the bulb-holder cover, locat-

ed underneath the bumper, then

insert the key in the notch B to

remove it.

Pass your hand underneath

the bumper to reach the bulb-

holder.

Rotate the bulb-holder a quarter

turn.

Pull on the bulb-holder.

Rotate the bulb a quarter turn to

remove it.

Replace the faulty bulb.

 Undo the lamp.

 Tilt the bulb-holder.

 Change the faulty bulb.

 Reposition the bulb-holder.

 Do up the lamp and reﬁt the bulb-

holder cover ﬁrmly in place.

Fit the bulb.

Reposition the bulb-holder by

rotating it a quarter turn.

XI

Copyright CITROEN compiled by C4owners.org

177

P R A C T I C A L I N F O R M AT I O N

Lamps mounted on the

bodywork

 Reﬁt the lamp unit on the body

and do up the two screws.

R e a r la m p s ( C 4 P ic a s s o )

 Reposition the plastic cover by

pressing on it.

Lamps mounted on the tailgate

1. Direction indicators

(PY 21 W)

2. Stoplamps/sidelamps

(P21/5 W)

3. Reversing lamp (P21 W )

 Identify the faulty bulb.

 With the boot open, press on the

plastic cover A, located close

to the lens, to release it from its

housing.

 Undo the two screws B on the

side of the lens and detach the

lamp by pulling it rearwards.

 Disconnect the connector linking

the lens unit with the tailgate.

 Remove the bulb-holder.

 Replace the bulbs.

To remove a bulb, rotate it a

 Identify the faulty bulb.

 With the boot open, remove the

plastic cover on the tailgate.

 Remove the bulb-holder from its

housing.

 Replace the bulb.

To remove a bulb, rotate it a

quarter turn.

To reﬁt the bulb, rotate it a quarter

turn in the other direction.

XI

quarter turn.

To reﬁt the bulb, rotate it a quarter

turn in the other direction.

 Reposition the bulb-holder.

_{ Reconnect th}C_eo_cop_ny_ner_cig_toh_{r t}t_o

C

_th

I

_eTROEN compiled by C4owners.org

 Reposition the bulb-holder.



R

eﬁt the plastic cover.

lens unit.

178

P R A C T I C A L I N F O R M AT I O N

Changing bulbs

 Identify the faulty bulb.

Number plate lamps (W 5 W)

R e a r la m p s

(Grand C4 Picasso)

 With the tailgate open, undo the

3 screws located on the side of

the lens unit and pull it rearwards

to detach.

 Disconnect the connector linking

the lens unit to the boot. Do not

disconnect the diodes.

 Remove the seal.

 Remove the bulb-holder.

 Replace the bulbs.

To remove a bulb, rotate it a

quarter turn.

To ﬁt the bulb, rotate it a quarter

turn in the other direction.

 Reposition the bulb-holder.

 Reﬁt the seal.

 Reconnect the connector to the

lens unit.

 Arrange the harness in the open-

ing provided in the body.

 Reﬁt the lens unit to the body

and ﬁt and tighten the 3 screws.

1. Direction indicators

(PY 21 W)

2. Stoplamps (P21 W)

3. Reversing lamp (P21 W)

4. Sidelamps (diodes)

 Insert a thin screwdriver into one

of the external holes of the lens.

 Push it outwards to unclip it.

 Remove the lens.

 Change the faulty bulb.

For this type of lamp, contact a

CITROËN dealer.

XI

Copyright CITROEN compiled by C4owners.org

179

P R A C T I C A L I N F O R M AT I O N

Third brake lamp with bulb

(W 5 W)

 With the boot open, detach the

Boot lamps (W 5 W)

Interior lighting

interior trim.

 Undo the nuts.

 Using a thin screwdriver, detach

the 3 retaining lugs.

 Remove the lamp via the exterior

of the tailgate.

 Remove the bulb-holder.

 Change the faulty bulb(s).

To reﬁt, carry out these operations in

reverse order.

Interior lamp (1/W 5 W)

Detach the unit by pushing it rear-

wards.

Detach the cover of the interior

lamp 1 with a thin screwdriver, close

to the button, to access the faulty

bulb.

Third brake lamp (diodes)

Torch (Krypton 3.6 V)

Map reading lamps (2/W 5 W)

Detach the cover of the interior lamp.

To access the faulty bulb, detach the

partition for the reading lamp 2 con-

cerned, as necessary.

 Open the tab.

XI

 Push with a ﬂat screwdriver

in the hole under the tab and

recover the bulb unit.

For the replacement of this type of

diode lamp, contact a CITROËN

dealer.

Copyright CITRO

E

^

N

^{Open the bulb unit ful}C^ly4^too^chw^ann^ge^ers.org

t

he bulb.

180

P R A C T I C A L I N F O R M AT I O N

Third brake lamp with bulb

(W 5 W)

 With the boot open, detach the

Boot lamps (W 5 W)

Interior lighting

interior trim.

 Undo the nuts.

 Using a thin screwdriver, detach

the 3 retaining lugs.

 Remove the lamp via the exterior

of the tailgate.

 Remove the bulb-holder.

 Change the faulty bulb(s).

To reﬁt, carry out these operations in

reverse order.

Interior lamp (1/W 5 W)

Detach the unit by pushing it rear-

wards.

Detach the cover of the interior

lamp 1 with a thin screwdriver, close

to the button, to access the faulty

bulb.

Third brake lamp (diodes)

Torch (Krypton 3.6 V)

Map reading lamps (2/W 5 W)

Detach the cover of the interior lamp.

To access the faulty bulb, detach the

partition for the reading lamp 2 con-

cerned, as necessary.

 Open the tab.

XI

 Push with a ﬂat screwdriver

in the hole under the tab and

recover the bulb unit.

For the replacement of this type of

diode lamp, contact a CITROËN

dealer.

Copyright CITRO

E

^

N

^{Open the bulb unit ful}C^ly4^too^chw^ann^ge^ers.org

t

he bulb.

180

P R A C T I C A L I N F O R M AT I O N

Use the special tool A that is pro-

vided in the fuse housing ﬂap, which

also contains spare fuses.

Fuses under the dashboard

C H A N G IN G A F U S E

Procedure for replacing a faulty fuse

with a new fuse to rectify a failure of

the corresponding function.

Correct

Incorrect

There are two fuseboxes under the

dashboard, one fusebox in the en-

gine compartment and another on

the battery.

Your vehicle's electrical

system is designed to oper-

ate with either standard or

optional equipment.

Changing a fuse

Before replacing a fuse, it is essen-

tial to ﬁnd the cause of the incident

and to have it rectiﬁed. The fuse

identiﬁcation numbers are indicated

inside the fusebox.

Tool A

Before installing electrical equip-

ment or accessories on your vehi-

cle, consult a CITROËN dealer.

Replace a blown fuse with one of the

same rating (the same colour).

CITROËN declines all responsibil-

ity for the consequences and costs

that are caused by faults or repairs

on your vehicle resulting from the

installation of accessories that

are not supplied and/or not rec-

ommended by CITROËN and not

installed according to its instruc-

tions, particularly when the energy

consumption of all of the additional

accessories connected exceeds

10 milliamperes (Ma).

Access to the ﬁrst dashboard

fusebox

XI

TROEN compiled by C4owners.org

181

P R A C T I C A L I N F O R M AT I O N

Fuses in the engine

compartment

Access to the fuses

 Detach and remove the cover.

After any operation, carefully reﬁt

the cover. If the cover is not cor-

rectly positioned or not properly

closed, this could cause serious

problems on your vehicle. For the

same reason, take care not to spill

any liquid in the fusebox.

XI

All work on the maxi-fuses,

which are located in these

fuseboxes and which give

extra protection, must be carried

out by a CITROËN dealer.

Copyright CITROEN compiled by C4owners.org

184

Technical Data for Your Citroen C4 Grand Picasso SUV First Generation (2006-2013)

Related Topics

Popular Owner Manuals

Latest Owner Manuals