Get Instruments and controls Guide for Citroen Ds3 SUV Second Generation (2018-2025)

Instruments and controls

Petrol - Diesel instrument panels, manual, electronic (ETG) or

automatic gearbox

Provided with permanent back-lighting, the instrument panel groups together the vehicle's dials and indicator and warning lamps.

dials

1. Rev counter.

4. display screen.

5. Fuel level.

7. Lighting dimmer button.

Adjusts the level of the instrument and

controls illumination and the interior mood

lighting.

Indicates the speed of rotation of the

engine (x 1 000 rpm).

2. Vehicle speed.

Indicates the quantity of fuel remaining in

the tank.

Indicates the current speed of the moving

vehicle (mph or km/h).

3. Engine coolant temperature.

Indicates the temperature of the engine

coolant liquid.

6. display management button.

Alternates display between range and trip

mileage recorder.

For more information, refer to the

paragraph relating to the button or

function and its associated display.

Servicing information.

Resets the selected function to zero (trip

distance recorder or service indicator).

19

Monitoring

Screen

A. Speed limiter

(mph or km/h) or

E. Service indicator

(miles or km), then

Cruise control.

Total mileage recorder

B. gear shift indicator.

C. Electronic or automatic gearbox

information.

These two functions are displayed

successively when switching on the ignition.

F. Engine oil level indicator

Appears a few seconds after switching on

the ignition, then disappears.

d. Range

(miles or km) or

Trip mileage recorder.

RACING petrol instrument panel, manual gearbox

Provided with permanent back-lighting, the instrument panel groups together the vehicle's dials and indicator and warning lamps.

dials

1. Rev counter.

4. display screen.

7. Lighting dimmer button.

Indicates the speed of rotation of the

engine (x 1 000 rpm).

2. Vehicle speed.

5. Fuel level.

Adjusts the level of the instrument and controls

illumination and the interior mood lighting.

Indicates the quantity of fuel remaining in

the tank.

Indicates the current speed of the moving

vehicle (mph or km/h).

3. Engine coolant temperature.

Indicates the temperature of the engine

coolant liquid.

6. display management button

Alternates display between range and trip

mileage recorder.

For more information, refer to the

paragraph relating to the button or

function and its associated display.

Servicing information.

Resets the selected function to zero (trip

distance recorder or service indicator).

21

Monitoring

Screen

A. Speed limiter

(mph or km/h) or

Cruise control.

B. Range

C. Service indicator

(miles or km), then

Total mileage recorder

These two functions are displayed

successively when switching on the

ignition.

(miles or km) or

Trip mileage recorder.

d. Engine oil level indicator

Appears a few seconds after switching on

the ignition, then disappears.

Indicator and warning lamps

Visual indicators informing the driver

that a system is in operation (operation

or deactivation indicator lamps) or of the

occurrence of a fault (warning lamp).

Associated warnings

The illumination of certain warning lamps may

be accompanied by an audible signal and a

message in the multifunction screen.

When the ignition is switched on

If they remain on, before moving off,

refer to the information on the warning

lamp concerned.

The passenger's airbag system

operation lamp stays on for about a

minute after switching on the ignition,

even after the engine has started.

The warning lamps may come on

continuously (fixed) or flash.

Certain warning lamps come on for a few

seconds when the vehicle's ignition is

switched on.

When the engine is started, these same

warning lamps should go off.

Certain warning lamps may come

on in two different modes. Only by

relating the type of lighting to the

operating status of the vehicle can it

be ascertained whether the situation is

normal or whether a fault has occurred.

23

Monitoring

Operation indicator lamps

If one of the following indicator lamps comes on, this confirms that the corresponding system has come into operation.

Warning/indicator lamp

is on

Cause

Action / Observations

Left-hand

flashing with buzzer.

The lighting stalk is pushed down.

direction indicator

Right-hand

flashing with buzzer.

The lighting stalk is pushed up.

direction indicator

Hazard warning

lamps

flashing with audible

signal.

The hazard warning lamps switch,

located on the dashboard, has been

operated.

The left-hand and right-hand direction indicators and

their associated indicator lamps flash simultaneously.

Sidelamps

fixed.

The lighting stalk is in the "Sidelamps"

position.

dipped beam

headlamps

The lighting stalk is in the "Dipped

beam headlamps" position.

Main beam

headlamps

The lighting stalk is pulled towards

you.

Pull the stalk to return to dipped beam headlamps.

Front foglamps

The front foglamps are switched on

using the ring on the lighting control

stalk.

Turn the ring on the lighting control stalk rearward

twice to switch off the front foglamps.

Rear foglamps

fixed.

The rear foglamps are on.

Turn the ring on the stalk rearward to switch off the

rear foglamps.

Warning/indicator lamp

is on

Cause

Action / Observations

diesel engine

fixed.

The key is at position 2 (ignition on) in Wait until the warning lamp goes off before starting.

pre-heating

the ignition switch.

The period of illumination of the warning lamp is

determined by the climatic conditions (up to about

thirty seconds in extreme climatic conditions).

If the engine does not start, switch the ignition off and

then on, wait until the warning lamp goes off again,

then start the engine.

Parking brake

Stop & Start

fixed.

The parking brake is applied or not

properly released.

Release the parking brake to switch off the warning

lamp, keeping your foot on the brake pedal.

Observe the safety recommendations.

For more information on the parking brake, refer to the

corresponding section.

When the vehicle stops (red lights,

The warning lamp goes off and the engine restarts

traffic jams, ...) the Stop & Start system automatically in START mode, as soon as you want to

has put the engine into STOP mode.

move off.

flashes for a few

seconds, then goes

off.

STOP mode is temporarily

unavailable.

or

For more information on special cases with STOP

mode and START mode, refer to the "Stop & Start"

section.

START mode is invoked

automatically.

25

Monitoring

Warning/indicator lamp

is on

Cause

Action / Observations

Foot on the

brake pedal

fixed.

The brake pedal must be pressed.

With an electronic gearbox, press the brake pedal to

start the engine (lever in position n).

With an automatic gearbox, with the engine running,

press the brake pedal before releasing the parking

brake, to unlock the lever and come out of position P.

If you wish to release the parking brake without

pressing the brake pedal, this warning lamp will

remain on.

flashing.

fixed.

With an electronic gearbox, if you

hold the vehicle on an incline using

the accelerator for too long, the

clutch overheats.

Use the brake pedal and/or the parking brake.

Automatic front wiping is activated.

Automatic

wiping

The wiper control is pushed

downwards.

deactivation indicator lamps

If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally.

This is may be accompanied by an audible signal and a message on the multifunction screen.

Warning/indicator lamp

is on

Cause

Action / Observations

Passenger's

fixed.

The control, located in the glove box, Set the control to the On position to activate the

airbag system

is set to the OFF position.

The passenger's front airbag is

deactivated.

passenger's front airbag.

In this case, do not fit a child seat in the rearward

facing position.

You can install a rearward facing

child seat, unless there is a fault with

the operation of the airbags (Airbag

warning lamp on).

27

Monitoring

Warning lamps

Any fault resulting in the illumination of a warning lamp must be investigated further by

When the engine is running or the vehicle is

being driven, the illumination of one of the

following warning lamps indicates a fault which

requires action on the part of the driver.

reading the associated message in the multifunction screen.

If you encounter any problems, do not hesitate to contact a CITROËN dealer or a qualified

workshop.

Warning/indicator lamp

STOP

is on

Cause

Action / Observations

fixed, alone or

associated with

Illumination of the warning lamp is

associated with a serious braking

Stop as soon as it is safe to do so as the engine may

cut out when driving.

another warning lamp,

accompanied by an

audible signal and a

message on the screen.

system or engine coolant temperature Park, switch off the ignition and call a CITROËN dealer

problem.

or a qualified workshop.

Service

temporarily.

Minor problems have occurred for

which there is no specific warning

lamp.

Identify the problem by reading the message shown in

the screen, such as, for example:

-

the engine oil level,

the screenwash level,

the remote control battery,

saturation of the particle emission filter on Diesel

vehicles (refer to the "Particle emissions filter

(Diesel)" section).

For any other faults, contact a CITROËN dealer or a qualified workshop.

fixed.

Major problems have occurred for

which there is no specific warning

lamp.

Identify the problem by reading the message shown

in the screen and contact a CITROËN dealer or a

qualified workshop.

Warning/indicator lamp

Braking

is on

Cause

Action / Observations

fixed, associated with

the STOP warning

lamp.

The braking system fluid level is too

low.

You must stop as soon as it is safe to do so.

Top up with brake fluid recommended by CITROËN.

If the problem persists, have the system checked by a

CITROËN dealer or a qualified workshop.

+

fixed, associated with

the STOP and ABS

warning lamp.

The electronic brake force distribution You must stop as soon as it is safe to do so.

(EBFD) system has a fault.

Have it checked by a CITROËN dealer or a qualified

workshop.

Anti-lock Braking fixed.

System (ABS)

The anti-lock braking system has a

fault.

The vehicle retains conventional braking.

Drive carefully at reduced speed and contact a

CITROËN dealer or a qualified workshop without delay.

dynamic stability flashing.

control (dSC/

Regulation by the system is active.

The system optimises traction and improves the

directional stability of the vehicle.

ASR)

fixed, associated with

The DSC/ASR or hill start assist

system has a fault.

Have it checked by a CITROËN dealer or a qualified

workshop.

illumination of the

indicator lamp in the

deactivation button,

accompanied by an

audible signal and a

message.

29

Monitoring

Warning/indicator lamp

is on

Cause

Action / Observations

Engine

flashing.

The engine management system has Risk of destruction of the catalytic converter.

autodiagnosis

system

a fault.

Have it checked by a CITROËN dealer or a qualified

workshop.

fixed.

The emission control system has a

fault.

The warning lamp should go off when the engine is started.

If it does not go off, contact a CITROËN dealer or qualified

workshop without delay.

Low fuel level

When it first comes on there remains You must refuel as soon as possible to avoid running

approximately 5 litres of fuel in the out of fuel.

tank.

This warning lamp will come on every time the ignition is

switched on, until a sufficient addition of fuel is made.

Fuel tank capacity: approximately 50 litres (petrol),

46 litres (Diesel) or 33 litres (LPG); depending on

version: approximately 30 litres (petrol or Diesel).

Never continue to drive until you run out of fuel as

this could damage the emission control and injection

systems.

Maximum coolant fixed.

temperature

The temperature of the cooling system Stop as soon as it is safe to do so.

is too high. Wait until the engine has cooled down before topping

up the level, if necessary.

If the problem persists, contact a CITROËN dealer or

qualified workshop.

Warning/indicator lamp

is on

Cause

Action / Observations

Engine oil

pressure

fixed.

There is a fault with the engine

lubrication system.

You must stop as soon it is safe to do so.

Park, switch off the ignition and contact a CITROËN

dealer or a qualified workshop.

Battery charge

fixed.

The battery charging circuit has a fault The warning lamp should go off when the engine is

(dirty or loose terminals, slack or cut

alternator belt, ...).

started.

If it does not go off, contact a CITROËN dealer or a

qualified workshop.

door(s) open

fixed if the speed is

below 6 mph (10 km/h).

fixed and accompanied

by an audible signal if

the speed is above

6 mph (10 km/h).

A door or the boot is still open.

Close the door or boot.

31

Monitoring

Warning/indicator lamp

Airbags

is on

Cause

Action / Observations

temporarily.

This lamp comes on for a few seconds This lamp should go off when the engine is started.

when you turn on the ignition, then

goes off.

If it does not go off, contact a CITROËN dealer or a

qualified workshop.

fixed.

One of the airbag or seat belt

pretensioner systems has a fault.

Have it checked by a CITROËN dealer or a qualified

workshop.

Seat belt not

fastened /

unfastened

fixed then flashing

accompanied by an

increasing audible

signal.

The driver and/or the front passenger Pull the strap then insert the tongue in the buckle.

has not fastened or has unfastened

their seat belt.

Power steering

fixed.

The power steering has a fault.

Drive carefully at reduced speed.

Have it checked by a CITROËN dealer or a qualified

workshop.

Warning/indicator lamp

Under-inflation

is on

Cause

Action / Observations

fixed, accompanied by The pressure in one or more tyres is

an audible signal and a too low.

message.

Check the tyre pressures as soon as possible.

This check should preferably be carried out when the

tyres are cold.

You must reinitialise the system after the adjustment of

one or more tyre pressures and after changing one or

more wheels.

For more information, refer to the "Under-inflation

detection" section.

flashing then fixed,

accompanied by the

Service warning lamp.

The system has fault: the tyre

pressures are no longer monitored.

Check the tyre pressures as soon as possible.

Have the system checked by a CITROËN dealer or a

qualified workshop.

+

33

Monitoring

Warning/indicator lamp

is on

Cause

Action / Observations

AdBlue^®additive fixed, on switching

(BlueHdi diesel) on the ignition,

accompanied by an

The remaining driving range is

between 350 miles (600 km) and

1500 miles (2400 km).

Have the AdBlue^®additive tank topped up as soon

as possible: go to a CITROËN dealer or a qualified

workshop, or carry out this operation yourself by

referring to the corresponding section.

audible signal and a

message indicating

the remaining driving

range.

flashing associated with The remaining driving range is

the SERVICE warning between 0 and 350 miles (600 km).

lamp, accompanied by

You must top-up the AdBlue^®additive tank to avoid

a breakdown: go to a CITROËN dealer or a qualified

workshop, or carry out this operation yourself by

referring to the corresponding section.

+

an audible signal and

a message indicating

the remaining driving

range.

flashing, associated

with the SERVICE

warning lamp,

accompanied by an

audible signal and a

message indicating

that starting is

The AdBlue^®tank is empty: the

starting inhibition system required

by legislation prevents starting of the

engine.

To be able to start the engine, you must top-up the

AdBlue^®additive tank: go to a CITROËN dealer or a

qualified workshop, or carry out this operation yourself

by referring to the corresponding section.

It is essential to add at least 3.8 litres of AdBlue^®to

the additive tank.

prevented.

Warning/indicator lamp

is on

Cause

Action / Observations

SCR emissions

control system

fixed, on switching on the

ignition, associated with

A fault with the SCR emissions control This alert disappears once the exhaust

system has been detected. emissions return to normal levels.

(BlueHdi diesel) the SERVICE and engine

diagnostic warning lamps,

+

accompanied by an audible

signal and a message.

flashing, on switching on

the ignition, associated with

the SERVICE and engine

diagnostic warning lamps,

accompanied by an audible

signal and a message

indicating the remaining driving

range.

After confirmation of the fault with the Contact a CITROËN dealer or a qualified

emissions control system, you can

drive for up to 650 miles (1 100 km)

before the engine starting inhibition

system is triggered.

workshop without delay, to avoid a

breakdown.

flashing, on switching on

the ignition, associated with

the SERVICE and engine

diagnostic warning lamps,

accompanied by an audible

signal and a message.

You have exceeded the authorised

driving limit following confirmation

of a fault with the emissions control

system: the engine starting inhibition

system prevents starting of the

engine.

To be able to start the engine, you must call

on a CITROËN dealer or a qualified workshop.

35

Monitoring

Coolant temperature indicator

With the engine running, when the needle is:

After driving for a few minutes, the temperature

and pressure in the cooling system increase.

To top up the level:

-

in zone A, the temperature is correct,

in zone B, the temperature is too high;

the central STOP warning lamp and the

maximum temperature warning lamp 1

come on in red, accompanied by an

audible signal and a message in the

multifunction screen.

F

wait for the engine to cool down,

unscrew the cap by two turns to allow the

pressure to drop,

F

when the pressure has dropped, remove

the cap,

top up the level to the "MAX" mark.

You must stop as soon as it is safe to do so.

Wait a few minutes before switching off the

engine.

Contact a CITROËN dealer or a qualified

workshop.

Service indicator

More than 1 800 miles (3 000 km)

remain before the next service is

due

Between 600 miles (1 000 km)

and 1 800 miles (3 000 km) remain

before the next service is due

When the ignition is switched on, no service

information appears in the screen.

For 5 seconds after the ignition is switched on,

the spanner symbolising the service operations

comes on. The distance recorder display line

indicates the distance remaining before the

next service is due.

Example: 1 739 miles (2 800 km) remain

before the next service is due.

For 5 seconds after the ignition is switched on,

the screen indicates:

System which informs the driver when the

next service is due, in accordance with the

manufacturer's servicing schedule.

The point at which the next service is due is

calculated from the last indicator zero reset,

depending on the distance travelled and the

time elapsed since the last service.

5 seconds after the ignition is switched on,

the spanner goes off; the distance recorder

resumes its normal operation. The screen then

indicates the total distance.

For BlueHDi Diesel versions, the

degree of deterioration of the engine oil

is also taken into account (depending

on the country of sale).

37

Monitoring

Less than 600 miles (1 000 km)

Service overdue

For BlueHDi Diesel versions, this alert

remain before the next service is due

For 5 seconds after the ignition is switched on,

the spanner flashes to indicate that the service

must be carried out as soon as possible.

Example: the service is overdue by 186 miles

(300 km).

may also be accompanied by the fixed

illumination of the service warning lamp

when the ignition is on.

Example: 560 miles (900 km) remain before

the next service is due.

For 5 seconds after the ignition is switched on,

the screen indicates:

For 5 seconds after the ignition is switched on,

the screen indicates:

The distance remaining may be

weighted by the time factor, depending

on the driving conditions.

Therefore, the spanner may also come

on if you have exceeded the period

since the last service, indicated in the

manufacturer's service schedule.

For BlueHDi Diesel versions, the

spanner may also be brought on earlier

than expected, depending on the

degree of deterioration of the engine oil

(depending on the country of sale).

The rate of deterioration of the engine

oil depends on the driving conditions in

which the vehicle is used.

5 seconds after the ignition is switched on,

the distance recorder resumes its normal

operation. The spanner remains on to

indicate that a service must be carried out

soon.

5 seconds after the ignition is switched on,

the distance recorder resumes its normal

operation. The spanner remains on.

Following this operation, if you wish to

disconnect the battery, lock the vehicle

and wait at least five minutes for the

zero reset to be taken into account.

Service indicator zero reset

After each service, the service indicator must

be reset to zero.

The procedure for resetting to zero is as

follows:

Retrieving the service

information

You can access the service information at any

time.

F

Press the trip distance recorder zero reset

button.

F

switch off the ignition,

press and hold the trip distance recorder

zero reset button,

The service information is displayed for a

few seconds, then disappears.

F

switch on the ignition; the distance recorder

display begins a countdown,

when the display indicates "=0", release

the button; the spanner disappears.

39

Monitoring

Engine oil level indicator*

Oil level correct

Oil level low

This is indicated by the flashing of "OIL",

accompanied by illumination of the service

warning lamp, an audible signal and a

message.

Oil level indicator fault

This is signaled by the flashing of "OIL--".

Contact a CITROËN dealer or a qualified

workshop.

In the event of a fault with the electric oil level

indicator, the engine oil level is no longer

monitored.

While the system is faulty, you should check

the engine oil level using the manual dipstick

located under the bonnet.

On vehicles fitted with an electric oil level

indicator, information on the oil level is

displayed in the instrument panel for a few

seconds when the ignition is switched on, after

the service information.

Refer to the "Checking levels" section.

If the low oil level is confirmed by a check using

the dipstick, the level must be topped up to

prevent damage to the engine.

Refer to the "Checking levels" section.

The level shown will only be correct

if the vehicle is on level ground and

the engine has been off for more than

30 minutes.

* Depending on version.

distance recorders

The total and trip distances are displayed for

thirty seconds when the ignition is switched off,

when the driver's door is opened and when the

vehicle is locked or unlocked.

When travelling abroad, you may

have to change the units of distance:

the display of road speed must be in

the official units (miles or km) for the

country. The change of units is done

via the screen configuration menu, with

the vehicle stationary.

Total distance recorder

It measures the total distance travelled by the

vehicle since its first registration.

Trip distance recorder

It measures the distance travelled since it was

reset to zero by the driver.

F

With the ignition on, press the button until

zeros appear.

41

Monitoring

Lighting dimmer

Black panel

(comfort night driving

display)

System for manual adjustment of the

brightness of the instruments and controls in

relation to the exterior brightness.

Activation

F

With the lighting on, press the left hand

button of the instrument panel several

When driving at night, this function allows

certain displays in the instrument panel to be

switched off so as to reduce fatigue for the

driver.

The essential driving information, such as the

speed of the vehicle, warning lamps, cruise

control or speed limiter information, remain

displayed in the instrument panel.

Activation

When the lighting is on:

times to progressively reduce the

dashboard lighting level.

F

press the button to change the brightness

of the instruments and controls,

F

Press the button again to reduce the

lighting to the minimum level and switch off

the interior mood lighting.

Press the button again to activate the black

panel.

F

when the level of brightness required is

reached, release the button.

deactivation

When the lighting is off, or in day mode on

vehicles fitted with daytime running lamps,

pressing the button does not have any effect.

Monochrome screen A

displays in the screen

Controls

Main menu

F

Press the "MEnU" button to gain access

to the main menu, then press the "5"

or "6" buttons to scroll through the various

menus:

-

radio-CD,

vehicle configuration,

options,

display settings,

languages,

units.

From the control panel of your Audio system,

you can:

This displays the following information:

-

time,

date,

F

press the "MEnU" button to gain access to

the main menu,

ambient temperature (this flashes if there is

a risk of ice),

press the "5" or "6" buttons to scroll

through the items in the screen,

press the "MOdE" button to change

the permanent application (date, audio

source...),

F

Press the "OK" button to select the menu

required.

-

status of the doors and boot,

current audio source (radio, CD...),

trip computer,

information or alert messages,

settings menus for the screen and the

vehicle systems.

F

press the "7" or "8" buttons to change a

setting value,

press the "OK" button to confirm,

or

press the "Back" button to abandon the

operation in progress.

43

Monitoring

Radio-Cd

Vehicle conﬁguration

Options

With the Audio system switched on, once the

"Radio-CD" menu has been selected you can

activate or deactivate the functions associated

with use of the radio (RDS, REG), or the CD

(introscan, shuffle, CD repeat).

Once the "Vehicle Configuration" menu has

been selected, you can activate or deactivate

the following equipment:

Once the "Options" menu has been selected,

you can start diagnostics of the status of the

equipment (active, not active, faulty).

-

wiper linked with reverse gear (refer to the

"Visibility" section),

guide-me-home lighting (refer to the

"Visibility" section),

parking sensors (refer to the "Driving"

section).

For more information on the "Radio-CD"

application, refer to the "Audio system" section.

This menu is also used to reinitialise the tyre

under-inflation detection system (refer to the

"Safety" section).

display settings

Languages

Once the "Display settings" menu has been selected,

you can gain access to the following settings:

Once the "Languages" menu has been selected,

you can change the language used by the

screen by choosing one from a defined list.

-

year,

month,

day,

hour,

minutes,

12 or 24 hour mode.

Setting the date and time

Units

F

Press the MEnU button.

Select "Display settings" using the "5"

or "6" button.

Once the "Units" menu has been selected,

you can change the units of the following

parameters:

F

Press "OK" to confirm the selection.

Select the "Year" function using the "5"

or "6" button.

-

temperature (°C or °F),

fuel consumption (l/100 km, mpg or km/l).

F

Press "OK" to confirm the selection.

Choose the desired value, using the "7"

or "8" button.

Once the fuel consumption units have

been set to mpg, the information in the

instrument panel screen on speed and

distance will also be in mph and miles.

F

Press "OK" to confirm the selection.

Repeat the procedure to set the "Month",

"Day", "Hours", and "Minutes".

F

Once you have selected a setting, press

the "7" or "8" buttons to change its value.

Press the "5" or "6" buttons to switch

respectively to the previous or next setting.

Press the "OK" button to save the change

and return to the normal display or press

the "Back" button to cancel.

As a safety measure, configuration by

the driver of the multifunction screen

should only be done when stationary.

45

Monitoring

Monochrome screen C

displays in the screen

Controls

Main menu

F

Press the "MEnU" button to gain access

to the main menu:

-

audio functions,

the trip computer,

personalisation-configuration,

telephone (hands-free kit).

Press the "5" or "6" buttons to select the

menu required, then confirm by pressing

the "OK" button.

This displays the following information:

From your Audio system control panel, you can:

-

time,

date,

F

press the "MEnU" button to gain access to

the main menu,

ambient temperature (this flashes if there is

a risk of ice),

status of doors and boot,

audio sources (radio, CD, USB port /

auxiliary socket etc.),

trip computer,

information or alert messages,

settings menus for the screen and vehicle

systems.

press the "5" or "6" buttons to scroll

through the items in the screen,

press the "MOdE" button to change the

permanent application (trip computer,

audio source...),

press the "7" or "8" buttons to change a

setting value,

press the "OK" button to confirm,

-

F

or

F

press the "Back" button to abandon the

operation in progress.

"Audio functions"

menu

"Trip computer" menu

With the Audio system switched on, once this

menu has been selected you can activate or

deactivate the functions associated with use

of the radio (RDS, REG, RadioText), the CD

(introscan, shuffle, CD repeat) or the MP3

player (USB port / auxiliary socket).

Once this menu has been selected, you can

consult information concerning the status of the

vehicle (warnings log, status of functions, etc.)

F

Press the "MEnU" button to gain access

to the general menu.

Press the arrows, then the "OK" button to

select the "Trip computer" menu.

For more information on the "Audio functions"

application , refer to the "Audio system" section.

Alert log

This summarises the active warning messages,

displaying them in succession in the

multifunction screen.

F

In the "Trip computer" menu, select one

of the following applications:

Status of functions

This summarises the status (active or inactive)

of the vehicle's functions.

Enter distance to destination

This allows you to enter an approximate

distance until your final destination.

47

Monitoring

"Personalisation-

Configuration" menu

-

parking sensors (refer the "Driving"

section).

automatic emergency braking (refer to the

"Active City Brake" section).

F

Press the "5" or "6" buttons, then the

"OK" button to select the "Guide-me-home

headlamps" line.

Once this menu has been selected, you can

gain access to the following functions:

This menu is also used to reinitialise the tyre

under-inflation detection system (refer to the

"Safety" section).

-

define the vehicle parameters,

display configuration,

choice of language.

Example: setting of the duration of the guide-

me-home lighting

F

Press the "7" or "8" buttons to set the

value required (15, 30 or 60 seconds), then

press the "OK" button to confirm.

F

Press the "5" or "6" buttons, then the

"OK" button to select the menu required.

Deﬁne the vehicle parameters

Once this menu has been selected, you can

activate or deactivate the following equipment:

-

wiper linked to reverse gear (refer to the

"Visibility" section),

-

guide-me-home lighting and duration (refer

to the "Visibility" section),

F

Press the "5" or "6" buttons, then the

"OK" button to select the "OK" box and

confirm or press the "Back" button to

cancel.

"Telephone" Menu

With Audio system on, once this menu is

selected you can configure your Bluetooth

hands-free system (pairing), view the various

telephone directories (list of calls, services...)

and manage your calls (call, hang up, second

call, secret mode...).

Display conﬁguration

Once this menu has been selected, you can

gain access to the following settings:

Choice of language

Once this menu has been selected, you can

change the language used by the screen by

choosing one from a defined list.

-

brightness-video setting,

date and time setting,

selection of units.

For more information on the "Telephone"

function, refer to the "Audio system" section.

As a safety measure, configuration by

the driver of the multifunction screen

should only be done when stationary.

Once the fuel consumption units have

been changed to mpg, the information

in the screen relating to speed and

distance also changes to mph and

miles respectively.

Setting the date and time

F

Select the "Set date and time" function

using the "5" or "6" button.

Press "OK" to confirm the selection.

Adjust the settings one by one using

the "7" or "8" button then confirm

with "OK".

F

Then select the "OK" box in the screen

and confirm.

49

Monitoring

Touch screen tablet

This system gives access to:

general operation

Recommendations

-

menus for adjusting settings for vehicle

functions and systems,

Principles

-

audio and display configuration menus,

audio system and telephone controls and

the display of associated information.

the display of alert messages,

the display of ambient temperature (a blue

snow flake appears if there is a risk of ice),

the trip computer.

It is necessary to press firmly, particularly for

"flick" gestures (scrolling through lists, moving

the map...).

A light wipe is not enough.

The screen does not recognise pressing with

more than one finger.

This technology allows use at all temperatures

and when wearing gloves.

Do not use pointed objects on the touch screen

tablet.

Press the "MEnU" button for access to the

different menus, then press the virtual buttons

in the touch screen tablet.

Each menu is displayed over one or two pages

(primary page and secondary page).

-

Use the "Options" button to go to the

secondary page.

Do not touch the touch screen tablet with wet

hands.

Uses a soft clean cloth to clean the touch

screen tablet.

After a few moments with no action on

the secondary page, the primary page

is displayed automatically.

And, depending on equipment, it allows:

-

the display of the visual parking sensors

information,

-

access to the controls for the navigation

system and Internet services, and the

display of associated information.

Use this button for access to

additional information and to the

settings for certain functions.

As a safety measure, some functions

can only be viewed when stationary.

Their display is interrupted as soon as

the vehicle moves off.

Use this button to confirm.

Use this button to return to the

primary page or to quit.

Menus

Press this button, then select the

desired menu.

navigation

Navigation is available depending on

the county and/or trim level.

Refer to the "Audio and telematics"

section.

Radio Media

Refer tothe "Audio and telematics"

section.

Settings

Allows configuration of the display

and the system.

Refer to the corresponding section.

Telephone

Refer to the "Audio and telematics"

section.

1. Volume / mute.

Refer to the "Audio and telematics" section.

Internet

These services are available

depending on the county and/or trim

level.

Refer to the "Audio and telematics"

section.

driving

Allows access to the trip computer and,

depending on version, the adjustment

of settings for certain functions.

Refer to the corresponding section.

51

Monitoring

"driving" menu

The functions accessible in this menu are given in the table below.

Button

Corresponding function

Comments

diagnostic

Recap of current alerts.

Under-inflation initialisation

Vehicle settings

Reinitialisation of tyre pressures.

Refer to the "Safety" section.

Access to other functions with settings that can be adjusted. The functions are grouped

together under three tabs:

-

"[driving assistance]"

-

"Automatic rear wiper in reverse" (Activation of rear wiper coupled to reverse gear: see

the "Visibility" section)

-

"Parking sensors" (Activation of rear parking sensors; refer to the "Driving" section).

"Automatic emergency braking" (Active City Brake; refer to the "Safety" section).

-

"[Lighting]"

-

"Mood lighting" (refer to the "Visibility" section).

"[Guide-me-home lighting]" (Automatic guide me home lighting; refer to the "Visibility"

section).

Select or deselect the tabs at the bottom of the screen to display the functions required.

"Settings" menu

The functions accessible in this menu are given in the table below.

Button

Corresponding function

Audio settings

Comments

Adjustment of volume, balance...

Turn off screen

System Settings

Turns off the display in the the touch screen tablet (black screen).

Pressing the black screen (or the MEnU button) restores the display.

Choice of units:

-

temperature (°Celsius or °Fahrenheit)

distance and fuel consumption (l/100 km, mpg or km/l).

Time/date

Setting the date and time.

Languages

Screen settings

Calculator

Calendar

Choice of language used from a defined list.

Adjustment of the display settings (scrolling of text, animations...) and the screen brightness.

Display the calculator.

Display the calendar.

53

Monitoring

Setting the date and time

F

Select the "Settings" menu.

F

Select "Adjust time" or "Adjust date".

F

Modify the settings using the number

keypad, then confirm.

Press "Confirm" to save and quit.

In the secondary page, press on "Time/

date".

When setting the time, you can select

"Satellite synchronisation", so that

the minutes are adjusted automatically

by satellite reception.

Trip computer

System that gives you information on the current journey (range, fuel consumption…).

Monochrome screen A

The trip computer provides the following

information:

-

range,

-

average speed.

current fuel consumption,

Stop & Start time counter,

distance travelled,

F

The next press then returns you to the

normal display.

Information displays

F

Press the button, located at the end of the

wiper stalk, to display the various items of

trip computer information in succession.

average fuel consumption,

Trip reset

F

Press the control for more than two

seconds to reset to zero the distance

travelled, the average fuel consumption

and the average speed.

55

Monitoring

Monochrome screen C

-

the current information tab

with:

● the range,

● the current fuel

consumption,

● the distance remaining

to be travelled or the

Stop & Start time counter,

-

the trip "1" tab with:

● the distance travelled,

● the average fuel

consumption,

● the average speed,

for the first trip.

Zero reset

Information displays

F

When the trip required is displayed, press

the button on the end of the wiper stalk for

more than two seconds.

F

Press the button, located at the end of

the wiper stalk, to display the various trip

computer tabs in succession:

-

the trip "2" tab with:

Trips "1" and "2" are independent but their use

is identical.

For example, trip "1" can be used for daily

figures, and trip "2" for monthly figures.

● the distance travelled,

● the average fuel

consumption,

● the average speed,

for the second trip.

F

Pressing the button again returns you to

the normal display.

Touch screen tablet

-

The "Instantaneous" tab with:

● the range,

● the current fuel consumption,

● the Stop & Start time counter.

The "Trip 1" tab with:

● the distance travelled.

● the average fuel consumption,

● the average speed,

for the first trip.

Information display

Trip reset

F

Press the MEnU button, then select

"driving", to display the various tabs.

Select the desired tab using your finger.

F

When the desired trip is displayed, press

the reset button.

F

The "Trip 2" tab with:

Trips "1" and "2" are independent but their use

is identical.

For example, trip "1" can be used for daily

figures, and trip "2" for monthly figures.

● the distance travelled.

● the average fuel consumption,

● the average speed,

for the second trip.

57

Monitoring

Trip computer, a few definitions

Range

Current fuel consumption

distance travelled

(miles or km)

(mpg or l/100 km or km/l)

(miles or km)

The distance which can still be travelled with

the fuel remaining in the tank (related to the

average fuel consumption over the last few

miles (kilometres) travelled).

Calculated over the last few seconds.

Calculated since the last trip computer reset.

distance remaining to

destination

This function is only displayed from

20 mph (30 km/h).

This value may vary following a change

in the style of driving or the relief,

resulting in a significant change in the

current fuel consumption.

(miles or km)

This is the distance remaining to be travelled

to the final destination. It can be entered by

the user.

If the distance is not entered, dashes are

displayed in place of the digits.

Average fuel

consumption

When the range falls below 20 miles (30 km),

dashes are displayed. After filling with at least

5 litres of fuel, the range is recalculated and is

displayed when it exceeds 60 miles (100 km).

(mpg or l/100 km or km/l)

Calculated since the last trip computer reset.

Stop & Start time

counter

(minutes / seconds or hours /

minutes)

If your vehicle is fitted with Stop & Start, a time

counter calculates the time spent in STOP

mode during a journey.

Average speed

(mph or km/h)

If dashes are displayed continuously

while driving in place of the digits,

contact a CITROËN dealer or a

qualified workshop.

Calculated since the last trip computer reset.

It resets to zero every time the ignition is

switched on with the key.

Instruments and controls for Your Citroen Ds3 SUV Second Generation (2018-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals