Advertisement

Advertisement

Servicing and Care -> Battery for Your Fiat 500 C 2 Door Second Generation (2021-2025)

CAR INACTIVITY (CARS  
EQUIPPED WITH  
START&STOP SYSTEM)  
BATTERY  
WARNING  
The car is fitted with a low-maintenance  
battery: no electrolyte top-ups with  
distilled water are needed in standard  
conditions of use.  
In the event of vehicle inactivity (or if the  
battery is replaced), special attention  
must be paid to the disconnection  
of the battery power supply.  
Proceed as follows: detach the  
connector A fig. 132 (by pressing  
button B) from sensor C for monitoring  
the status of the battery installed on  
the negative battery pole D. This sensor  
should never be disconnected from  
the battery pole except if the battery is  
replaced.  
180) Battery fluid is poisonous and  
corrosive. Avoid contact with skin and  
eyes. Keep naked flames and sources of  
sparks away from the battery: risk of  
explosion and fire.  
INSPECTING THE  
CHARGE AND THE  
ELECTROLYTE LEVEL  
181) Running the battery with an  
excessively low liquid level will damage the  
battery beyond repair and could even  
cause its explosion  
The operations must be carried out as  
described in this Owner Handbook only  
by specialised personnel. Topping  
must be carried out by specialised  
personnel at a Fiat Dealership.  
182) If the vehicle must remain unused for  
a long time at a very low temperature,  
remove the battery and take it to a warm  
place, to avoid freezing.  
183) When performing any operation on  
the battery or near it, always protect your  
eyes with special goggles.  
180) 181)  
IMPORTANT After turning the ignition  
key to STOP and having closed the  
driver's side door, wait at least one  
minute before disconnecting the battery  
and then reconnecting the electrical  
supply to the battery.  
REPLACING THE  
BATTERY  
184) Do not attempt to charge a frozen  
battery: it must be thawed first, otherwise it  
may explode. If freezing has occurred, the  
battery should be checked by skilled  
personnel to make sure that the internal  
elements are not damaged and that the  
body is not cracked, with the risk of leaking  
poisonous and corrosive acid.  
If required, replace the battery with a  
genuine spare part with the same  
specifications.  
If a battery with different specifications  
is fitted, the service intervals given in  
the "Service Schedule" will no longer be  
valid.  
Follow the battery manufacturer's  
instructions for maintenance.  
182) 183) 184)  
64)  
5)  
F0S0372  
132  
149  
BRAKES  
REPLACING THE  
WINDSCREEN/REAR  
WINDOW WIPER  
BLADES  
WARNING  
Depending on the version/market, the  
vehicle may be equipped with  
mechanical wear detectors for the  
brake pads: one for each wheel  
assembly.  
64) Incorrect installation of electric and  
electronic devices may cause severe  
damage to your car. After purchasing your  
vehicle, if you wish to install any  
accessories (anti-theft, etc.), go to a Fiat  
Dealership, which will suggest the most  
suitable devices and advise you whether a  
higher capacity battery needs to be  
installed.  
WIPER BLADES  
When the brake linings are close to  
wearing out, pressing the brake pedal  
will generate a slight squeal: this lasts  
for about 100 km (the mileage varies  
with the driving style and route).  
In this case, it is still possible to  
continue driving, with caution.  
However, contact a Fiat Dealership as  
soon as possible to have the worn  
brake pads changed.  
Replace the blades if the rubber edge is  
deformed or worn. In any case, it is  
advisable to replace them  
approximately once a year.  
185) 186)  
WARNING  
RAISING THE  
WINDSCREEN WIPER  
BLADES  
5) Batteries contain substances which are  
very dangerous for the environment. It is  
advisable to contact a Fiat Dealership  
for battery replacement.  
Lift the windscreen wiper arm and  
position the blade so that it forms a 90°  
angle with the arm.  
REPLACING THE  
WINDSCREEN WIPER  
BLADES  
Proceed as follows:  
raise the wiper arm A fig. 133 and  
position the blade so that it forms  
an angle of 90° with the arm;  
press the button A and extract the  
blade C from the arm B;  
insert the new blade making sure it  
is locked into place.  
150