Get Knowing the Instrument Panel Guide for Fiat Fiorino SUV Third Generation (2015-2026)

KNOWING THE INSTRUMENT PANEL

This section of the handbook provides

DASHBOARD AND INSTRUMENT

all information that is useful for getting

to know, interpreting, and using the

instrument panel correctly.

PANEL........................................ 64

DIGITAL DISPLAY ........................ 69

MULTIFUNCTION DISPLAY ........... 72

TRIP COMPUTER ........................ 78

EOBD SYSTEM ........................... 79

WARNING LIGHTS AND

MESSAGES ................................ 81

63

DASHBOARD AND INSTRUMENT PANEL

Versions with digital display

and

are available on diesel versions only.

^Wꢀ ^{arning lights}

122

F0T0807

A. Speedometer B. Fuel level gauge with reserve warning light C. Engine coolant temperature indicator with overheating warning

light D. Rev counter E. Digital display

64

Versions with digital display

Warning lights

and

are available on diesel versions only.

ꢀ

123

F0T0808

A. Speedometer B. Fuel level gauge with reserve warning light C. Engine coolant temperature indicator with overheating warning

light D. Rev counter E. Digital display

65

Versions with multifunction display

and

are available on diesel versions only.

^Wꢀ ^{arning lights}

124

F0T0809

A. Speedometer B. Fuel level gauge with reserve warning light C. Engine coolant temperature indicator with overheating warning

light D. Rev counter E. Multifunction display

66

Versions with multifunction display

Warning lights

and

are available on diesel versions only.

ꢀ

125

F0T0810

A. Speedometer B. Fuel level gauge with reserve warning light C. Engine coolant temperature indicator with overheating warning

light D. Rev counter E. Multifunction display

67

The instrument background colour

and type may vary according to the

versions.

SPEEDOMETER

Indicates vehicle speed.

127

F0T0805

128

F0T0806

This is normal and does not indicate a

fault. It may be caused, for example,

by the activation of the climate control

system or fan. In these cases, a slow

change in revs is used to protect the

battery charge.

WARNING The needle will point to (E)

and the warning light (A) will flash to

indicate a fault in the system. If this

is the case, go to a Fiat Dealership to

have the system checked.

126

F0T0804

REV COUNTER

FUEL LEVEL GAUGE

This shows the amount of fuel left in the

fuel tank.

The rev counter shows the number of

engine revolutions per minute.

ENGINE COOLANT

TEMPERATURE

INDICATOR

Warning light (A) fig. 128 comes on to

indicate that approximately 6-7 litres of

fuel are left in the tank.

This shows the temperature of the

engine coolant fluid and starts working

when the fluid temperature exceeds

approx. 50°C. In normal use, the

needle could assume different positions

within the scale, depending on the

usage conditions.

(C) - Low engine coolant temperature.

(H) - High engine coolant temperature.

Warning light (B) fig. 128 may switch

on (together with a message on the

display) to indicate that the coolant

temperature is too high; in this case,

WARNING The electronic injection

control system gradually shuts off the

flow of fuel when the engine is over-

revving, resulting in a gradual loss of

engine power. When the engine is

idling, the rev counter may indicate

a gradual or sudden increase of the

speed.

(E) - tank empty.

(F) - tank full (see the description in

paragraph "Vehicle refuelling" in this

chapter).

Do not travel with the tank nearly empty

to prevent damaging the catalytic

converter.

68

stop the engine and contact a Fiat

Note Buttons

and

activate

Dealership.

different functions according to the

following situations:

10)

Headlight alignment adjustment

With the dipped beam headlights on,

IMPORTANT

press button

or

to adjust

headlight alignment.

10) If the needle for the engine coolant

temperature reaches the red area, stop

the engine immediately and contact a Fiat

Dealership.

Setup menu

within the menu, they allow you to

scroll up or down through the options;

to increase or decrease values during

settings.

129

F0T0811

CONTROL BUTTONS

DIGITAL DISPLAY

STANDARD SCREEN

The standard screen fig. 129 shows

the following information:

A Headlamp alignment position (only

with dipped headlamps on).

B Milometer (display of kilometres, or

miles, travelled).

SETUP MENU

Setup menu functions

The menu comprises a series of

functions arranged in a "circular way",

which can be selected through the

and

buttons to access the

different selection operations and

settings (setup) given in the following

paragraphs.

130

F0T0500

C Time.

D START&STOP function indicator (for

versions/markets where provided)

E Gear Shift Indication (for

versions/markets, where provided).

F Petrol operation (Natural Power

versions).

The menu can be activated by pressing

To scroll up through the screen

and the related options or to increase

the displayed value.

the SET

button briefly.

Single presses on the

buttons will scroll the setup menu

options.

Management modes differ according

to the characteristic of the option

selected.

and

SET

Press briefly to access the

menu and/or go to next screen or

confirm the selection. Hold down to go

back to the standard screen.

To scroll down through the screen

and the related options or to decrease

the displayed value.

G Trip computer data.

Note With key removed (when opening

at least one of the front doors) the

display turns on and shows the time

and distance covered for a few

seconds.

The menu includes the following items:

69

ILLU

SPEEd

Hour

bUZZ

press the SET

display will show the wording ILLU;

press button and to set the

required brightness level;

press the SET button briefly

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

button briefly: the

Hold the SET button pressed

quit the set up menu if you are in the

menu;

quit the displayed menu if you are

setting an option;

Unit

BAG P (for versions/markets, where

provided)

Selecting a menu option

press the SET

select the menu setting you wish to

change;

press the

(with single presses) to select the new

setting;

press the SET

store the new setting and at the same

time go back to the previously selected

menu option.

save only the changes already stored

by the user (and confirmed by pressing

the SET

button).

button briefly to

Setting a speed limit (SPEEd)

This function is used to set a speed

limit (km/h or mph); the driver is

alerted when this limit is exceeded

(see “Warning lights and messages”

in the "Knowing the instrument panel"

chapter).

The set-up menu page is timed. When

the menu is exited due to expiry of the

time allowed, only the changes already

stored by the user (and confirmed by

and

buttons

pressing the SET

button briefly) will

be saved.

From the standard screen, press

button briefly to

the SET

browsing.

Press

button briefly to start

To set the desired speed limit, proceed

as follows:

or to browse within the

the SET

button briefly: the

Selecting “Set Clock”

menu.

display will show the wording (SPEED)

and the unit (km/h) or (mph) previously

set;

press the SET

select the first value to change (hours);

press the and buttons

(with single presses) to select the new

setting;

button briefly to

Note Only the short menu can be

accessed while the vehicle is moving

for reasons of safety ("SPEEd" setting).

Stop the vehicle to access the full

menu.

press

limit activation (On) or deactivation (Off);

if the function is On, press or

to select the required speed limit

or

to select speed

press the SET

button briefly to

Adjusting the vehicle interior

lighting (ILLU)

store the new setting and at the same

time go to the next set-up menu option

(minutes);

after setting the values with the same

procedure, go back to the previous

menu item.

and then press SET

to confirm;

Nota The speed may be set in the

range from 30 to 200 km/h, or from 20

to 125 mph according to the previously

chosen unit (see “Setting the unit of

measurement” below). The setting will

increase/decrease by five units each

This function is available with the

dipped beam headlights on to adjust

brightness of the instrument panel,

buttons and radio display.

Proceed as follows to adjust the light

intensity:

time the

Hold down the

/

button is pressed.

button to

/

70

the button down to go back to the

standard screen without saving.

automatically increase/decrease the

setting rapidly.

Complete the adjustment with single

presses of the button when you

approach the desired value.

Passenger front airbag

and chest-pelvis side bag

activation/deactivation (Bag P) (for

versions/markets, where provided)

This function is used to

activate/deactivate the front passenger

airbag.

Adjusting the buzzer volume (bUZZ)

This function is used to adjust

the volume of the acoustic signal

(buzzer) that sounds in the event of

failure/warning indications and when

press the SET

button briefly

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

To cancel the setting, proceed as

follows:

Proceed as follows fig. 131:

the SET

,

and

buttons

press the SET

button and,

are pressed.

To set the desired volume, proceed as

follows:

after the message BAG P OFF (to

deactivate) or BAG P On (to activate) is

displayed by pressing buttons

, press SET again;

a confirmation request message will

appear on the display;

or

briefly press the SET

button

press the SET

display will show the wording (bUZZ)

- press or to select the

button briefly: the

briefly to make the display flash (On);

press

: (Off) will flash on the

display;

required volume (adjustable over 8

levels).

press buttons

or

press the SET

button briefly

to select (YES) (confirming

activation/deactivation) or (no) (to

abort);

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

press the SET

button briefly

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

briefly press the SET

button: a

Setting the clock (Hour);

With this function, it is possible to set

the time.

message confirming the selection will

be displayed and you will return to the

menu screen or, pressing the button for

longer, you will return to the standard

screen without saving.

Setting the distance unit (Unit)

This function is used to set the unit of

measurement.

To adjust, proceed as follows:

press the SET

button briefly:

To adjust, proceed as follows:

"hours" starts flashing on the display;

press the SET

button briefly: the

press the

make the adjustment;

briefly press the SET

or

button to

button:

display will show the wording (Unit) and

the previously set unit (km) or (mi);

press

required unit.

press the SET

or

to select the

button briefly

"minutes" starts flashing on the display;

press the

or

p button to

make the adjustment;

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

press the SET

button briefly

to return to the menu screen or hold

71

Note When opening one of the front

doors, the display turns on and shows

the time and the kilometres (or miles)

covered for a few seconds.

MULTIFUNCTION

DISPLAY

The vehicle may be equipped with a

multifunction display that gives the

driver useful information depending on

the previous settings.

CONTROL BUTTONS

STANDARD SCREEN

133

F0T0500

To scroll up through the screen

and the related options or to increase

the displayed value.

132

F0T0812

The standard screen fig. 132 shows

the following information:

A Date.

B Milometer (display of kilometres, or

miles, travelled).

C Time.

D Outside temperature.

SET

Press briefly to access the

menu and/or go to next screen or

confirm the selection. Hold down to go

back to the standard screen.

To scroll down through the screen

and the related options or to decrease

the displayed value.

131

F0T1027

Note Buttons

different functions according to the

following situations:

and

activate

E Headlamp alignment position (only

with dipped headlamps on).

F START&STOP function indicator (for

versions/markets where provided).

G Gear Shift Indication (for

versions/markets, where provided).

Headlight alignment adjustment

the dipped beam headlights on,

press button

or

to adjust

headlight alignment.

72

Setup menu

LANGUAGE

press the SET

button briefly to

WARNINGS VOLUME

BUZZER VOLUME

SEAT BELT REMINDER

SERVICE

PASSENGER AIRBAG

EXIT MENU

Selecting an item from the main menu

without a submenu:

briefly press the SET

store the new setting and at the same

time go back to the previously selected

submenu option.

within the menu, they allow you to

scroll up or down through the options;

to increase or decrease values during

settings.

Selecting “Date” and “Set Clock”:

briefly press the SET

button to

SETUP MENU

Setup menu functions

The menu comprises a series of

functions arranged in a "circular way",

which can be selected through the

select the first value to be changed

(e.g. hours / minutes or year / month /

day).

button to

press

presses) to select the new setting;

press the SET button briefly

or

(with single

select the main menu setting you wish

to change;

and

buttons to access the

different selection operations and

settings (setup) given in the following

paragraphs. A submenu is provided for

some items (Set time and Units).

The set-up menu is activated by

press

presses) to select the new setting;

press the SET button briefly to

or

(with single

to store the new setting and at the

same time go to the next set-up menu

option. If the processed option is the

last one, the system brings you back

to the previously selected option of the

menu.

store the new setting and at the same

time go back to the previously selected

main menu option.

Selecting an option from the main

menu with a submenu:

pressing the SET

button briefly.

Press buttons

or to scroll the

Hold the SET

button pressed:

setup menu options.

exit the set-up menu if you are in the

main menu;

Operating modes are different

according to the characteristics of the

option selected.

The menu includes the following items:

DIMMER

SPEED BUZZER

TRIP B DATA

SET TIME

SET DATE

press the SET

display the first submenu option;

press or (with single

button briefly to

exit the main menu if you are in

another point of the menu (e.g.: at

submenu option setting level, at

submenu level or at main menu option

setting level);

presses) to scroll all the submenu

options;

press the SET

button briefly to

select the displayed submenu option

and to open the relevant settings

menu;

save only the changes already stored

by the user (and confirmed by pressing

the SET

button).

SEE RADIO

AUTOCLOSE

UNITS OF MEASUREMENT

press

or

(with single

The set-up menu page is timed. When

the menu is exited due to the expiry

of the time allowed, only the changes

already stored by the user (and

presses) to select the new setting for

this submenu option;

73

(see “Warning lights and messages”

in the "Knowing the instrument panel"

chapter).

To set the desired speed limit, proceed

as follows:

briefly press the SET

briefly to make the display flash (On);

button

confirmed by pressing the SET

button briefly) will be saved.

From the standard screen, press

press

display;

press the SET

: (Off) will flash on the

button briefly

the SET

browsing.

Press

button briefly to start

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

briefly press the SET

button: the

or to browse within the

display will show the wording (Speed

Beep);

menu.

Not. Only the short menu may be

accessed for reasons of safety while

the vehicle is moving ("Speed Buzzer"

setting). Stop the vehicle to access the

full menu.

press button

or

to

Trip B On/Off (Trip B data)

This function can be used to activate

(On) or deactivate (Off) the Trip

B display (partial trip). For more

information see the "Trip computer"

paragraph.

Proceed as follows to switch the

function on/off:

press the button press the button

select speed limit activation (On) or

deactivation (Off);

if the function is On, press

or

to select the required speed limit

Adjusting the vehicle interior

lighting

and then press SET

button to

confirm.

This function is available with the

dipped beam headlights on to adjust

brightness of the instrument panel,

buttons and radio display.

Proceed as follows to adjust the light

intensity:

Note The speed may be set anywhere

between 30 and 200 km/h or 20 and

125 mph, depending on the previously

chosen unit, see the “Setting the unit

of measurement (Units)” paragraph.

The setting will increase/decrease

by 5 units each time button

SET

button briefly to make the

display flash On or Off depending on

the previous setting;

press

choice;

press the SET

or

to make your

button briefly

press the SET

button briefly to

make the display flash the previously

set level;

/

is pressed. Hold down the

button to automatically

/

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

press button

required brightness level;

press the SET button briefly

or

to set the

increase/decrease the setting rapidly.

Complete the adjustment with single

presses of the button when you

approach the desired value.

Setting the clock (Set time)

This function allows the adjustment of

the clock through two submenus: Time

and Format.

To carry out the adjustment, proceed

as follows:

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

press the SET

button briefly

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

To cancel the setting, proceed as

follows:

Speed limit (Speed Beep)

This function is used to set a vehicle

speed limit (km/h or mph); the driver

is alerted when this limit is exceeded

74

briefly press the SET

and the two submenus "Time" and

"Format" will be displayed;

button

Setting the date (Set Date)

This function allows updating of the

date (day - month - year).

Radio: selected radio station

frequency or RDS message, automatic

tuning activation or AutoSTore;

Audio CD, MP3 CDs: track number;

CD Changer: CD number and track

number;

To show the sound system information

on the display (On) or clear it (Off),

proceed as follows:

press the

or

button to

briefly press the SET

button:

switch between the two submenus;

you have selected the submenu to

be changed, press the SET

briefly;

"day" (dd) starts flashing on the display;

press the

or

button to

button

make the adjustment;

briefly press the SET

button:

when you select "Time", pressing

"month" starts flashing on the display

(mm);

the SET

button briefly makes the

briefly press the SET

button

"hours" flash on the display;

press the

make the adjustment;

briefly press the SET

or

button to

button:

to make the display flash On or Off

depending on the previous setting;

press the

or

button to

button:

make the adjustment;

briefly press the SET

"minutes" starts flashing on the display;

press the or button to

make the adjustment;

when you select "Format", pressing

press

choice;

press the SET

or

to make your

button briefly

"year" starts flashing on the display

(yyyy);

press the button

or

to

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

make the adjustment.

Note The setting will increase or

decrease by one unit each time

the SET

button briefly makes the

Automatic central locking with

vehicle moving (Autoclose)

After activation (On), this function

allows the automatic locking of the

doors when the speed exceeds 20

km/h.

display mode flash on the display;

the

or

button is pressed.

press the

or

button to carry

Keeping the button pressed

causes an automatic rapid value

increase/decrease.

Complete the adjustment with single

presses of the button when you

approach the desired value.

out the selection in 24h or 12h mode.

When you have made the required

settings, press the SET

briefly to go back to the submenu

screen or hold the button down to go

back to the main menu screen without

saving.

button

Proceed as follows to activate (On) or

deactivate (Off) this function:

press the SET

button briefly

briefly press the SET

display a submenu;

briefly press the SET

button to

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

press the SET

button down again

button

to return to the standard screen or to

the main menu according to where you

are in the menu.

to make the display flash On or Off

depending on the previous setting;

Audio information (See radio)

This function is used to display radio

information.

press

or

to make your

choice;

75

briefly press the SET

button to

"mpg" (depending on the previous

setting);

To set the desired language, proceed

as follows:

return to the submenu screen or hold

the button down to return to the main

menu screen without saving;

If the set distance unit is "km", the

display enables setting of the fuel

consumption unit (km/l or l/100km).

If the set distance unit is "mi", the

display shows the amount of fuel

consumed in "mpg".

briefly press the SET

button : the

previously set "language" starts flashing

on the display;

press the SET

button down again

to return to the standard screen or to

the main menu according to where you

are in the menu.

press

choice;

press the SET

or

to make your

button briefly

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

press

choice;

or

to make your

Setting the unit of measurement

This function allows the setting of

a unit of measurement via three

submenus: Distance, Consumption and

Temperature.

when you enter the "Temperature"

submenu: briefly pressing the SET

button makes the display show "°C"

or "°F" (depending on the previous

setting);

Adjust the failure/warning buzzer

volume (Buzzer Volume)

With this function the volume of the

buzzer which accompanies the display

of any failure/warning can be adjusted

according to 8 levels.

To set the desired unit of

measurement, proceed as follows:

press

choice;

or

to make your

briefly press the SET

display the three submenus;

press the or button to

button to

When you have made the required

settings, press the SET button

briefly to go back to the submenu

screen or hold the button down to go

back to the main menu screen without

saving.

To set the desired volume, proceed as

follows:

navigate through the three submenus;

after you have selected the submenu

to be changed, press the SET

button briefly;

briefly press the SET

button:

the previously set volume "level" starts

flashing;

when you enter the "Distance"

press the

or

button to

press the SET

button down again

submenu, pressing the SET

button

make the adjustment;

to return to the standard screen or to

the main menu according to where you

are in the menu.

briefly makes the display show "km"

or "mi" (depending on the previous

setting);

press the SET

button briefly

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

press

or

to make your

Selecting the language (Language)

Messages on the display can be shown

in the following languages: Italian,

German, English, Spanish, French,

Portuguese, Turkish and Dutch.

choice;

when you enter the "Fuel

Consumption" submenu, pressing

Adjusting the button volume

(Button Vol.)

This function is used to set the volume

of the acoustic signal accompanying

the SET

button briefly makes the

display show "km/l", "l/ 100km" or

76

the button down to go back to the

standard screen.

(Passenger Bag: On) (to activate) by

pressing or , press the SET

button once again);

a confirmation request message will

the activation of the SET

,

and

buttons through 8 levels.

To set the desired volume, proceed as

follows:

briefly press the SET

the previously set volume "level" starts

Note The “Scheduled Servicing Plan”

includes vehicle maintenance at fixed

intervals; refer to the “Maintenance

and care” chapter. The indication of

the "Service" function will appear

automatically, with the key in MAR

position, starting from 2,000 km (or

1,240 mi) and will be displayed every

200 km (or 124 mi).

Below 200 km servicing indications

are more frequent. The display will be

in km or miles according to the unit

of measurement set. When the next

service is close, when the ignition is

turned ON the word "Service" appears

in the display followed by the remaining

number of kilometres/miles.

appear on the display;

button:

use the

or

menu buttons

to select (Yes) (to confirm the

activation/deactivation) or (No) (to

cancel);

flashing;

press the

or

button to

make the adjustment;

briefly press the SET

button: a

press the SET

button briefly

message confirming the selection will

be displayed and you will return to the

menu screen or, pressing the button for

longer, you will return to the standard

screen without saving.

to return to the menu screen or hold

the button down to go back to the

standard screen without saving.

Reactivation of buzzer for S.B.R.

signal (Belt buzzer)

This function can be displayed only

after a Fiat Dealership has deactivated

the SBR system (see "SBR system" in

the "Safety" section).

Exit Menu

This is the last function that closes the

cycle of settings listed in the menu

screen.

Go to a Fiat Dealership, where the

"Scheduled Service Plan" operations

will be performed and the message will

be reset.

Press the SET

button briefly to

Scheduled Servicing (Service)

Using this function you can display

information about the mileage intervals

for vehicle servicing.

To consult the information, proceed as

follows:

go back to the display to the standard

screen without saving.

Press

to return to the first menu

Passenger front airbag

and chest-pelvis side bag

activation/deactivation

(for versions/markets, where provided)

This function allows the passenger side

airbag to be activated/deactivated.

Proceed as follows:

option (Speed Beep).

briefly press the SET

button:

the display will show when servicing

is due in km or mi according to the

previous setting (see paragraph "Units

of measurement");

briefly press the SET

go back to the menu screen or hold

press the SET

button and, after

button to

the display shows the Bag pass:

Off) (to deactivate) or the message

77

as a function of the overall time elapsed

since the start of a new mission.

Travel Time

Time elapsed since the start of the new

journey.

be travelled with the fuel in the tank,

assuming that driving style remains

unvaried. The display will show the

reading '-----' when the following

events take place:

range is lower than 50 km (or 30 mi)

vehicle is left parked with the engine

running for a long time.

TRIP COMPUTER

General information

The Trip computer is used to display

information on vehicle operation when

the ignition key is turned to MAR.

This function allows you to define two

separate trips, called "Trip A" and

"Trip B", for monitoring the "complete

mission" (journey) of the vehicle in a

reciprocally independent manner. Both

functions can be reset (reset means

start of a new journey).

"Trip A" can be used to display the

values relating to:

External temperature

Range

Travel Distance

WARNING If there is no information,

the Trip computer displays "----"

in place of the value. When normal

operating conditions are restored,

the counting of the various values is

resumed, without either zeroing the

values displayed prior to the problem,

or starting a new mission.

WARNING The range can be affected

by several factors: driving style

(see “Driving style” in the “Starting

and driving” section), type of route

(motorway, towns and cities, mountain

roads, etc.), conditions of use (load,

tyre pressures, etc.). Trip planning must

therefore take the above into account.

TRIP control button

The TRIP button is located on the right

stalk fig. 134. With the ignition key

turned to MAR-ON, this button allows

you to view the previously described

values and also zero them to begin a

new journey:

brief press to access the various

values displays;

long press to reset and then start a

Travel Distance

Average fuel consumption

Current Consumption

Average Speed

This value shows the distance travelled

from the start of the new journey.

Average fuel consumption

This value shows the approximate

average fuel consumption from the

start of the new journey.

Trip time (driving time).

"Trip B", available on multifunction

display only, is used to display the

values relating to:

Travel Distance B

Average Fuel Consumption B

Average Speed B

Current Consumption

new mission.

This value shows the fuel consumption.

The value is constantly updated. The

message “----” will appear on the

display if the vehicle is parked with the

engine running.

Average Speed

Represents the vehicle average speed

Trip time B (driving time).

11)

Values displayed

Range (for versions/markets, where

provided)

This indicates the distance that can still

78

Start of journey procedure

With the ignition key in the MAR-ON

position, reset by pressing the TRIP

button and keeping it pressed for more

than 2 seconds.

EOBD SYSTEM

The EOBD system (European On Board

Diagnosis) allows continuous diagnosis

of emission-related components on the

vehicle to be made.

TR

I

P

Exit Trip

It also alerts the driver, by switching

The TRIP function ends automatically

once all the values have been displayed

on the warning light

on the

instrument panel (together with a

message on the display), when these

components are no longer in peak

condition (see “Warning lights and

messages” paragraph in the "Knowing

the instrument panel" chapter).

The aim of the system is to:

or by holding the SET

button down

134

F0T0984

for more than 1 second.

New mission

This begins after a reset:

IMPORTANT

"manual" resetting by the user, by

pressing the relevant button;

“automatic” resetting, when the “trip

distance” reaches 9999.9 km or when

the “travel time” reaches 99:59 (99

hours and 59 minutes);

11) The "Trip B" function may be

disabled (see the "Activating Trip B"

paragraph). "Range" and "Instantaneous

fuel consumption" information can not be

reset.

monitor system efficiency;

indicate an increase in emissions due

to vehicle malfunction;

indicate the need to replace

components which have deteriorated.

The system also has a connector that

can be interfaced with appropriate

equipment, which makes it possible

to read the error codes stored in the

control unit together with a series

of specific parameters for engine

operation and diagnosis.

after disconnection/reconnection of

the battery.

WARNING The reset operation when

“Trip A” details are being displayed only

resets the information associated with

this function.

This check can also be carried out by

traffic control authorities.

WARNING The reset operation when

“Trip B” details are being displayed

resets only the information associated

with this function.

WARNING After eliminating the failure,

to check the system completely, Fiat

Dealerships run a bench test and, if

79

necessary, road tests which may also

call for a long journey.

45)

WARNING

45) Go to a Fiat Dealership as soon as

possible if warning light

either does not

light up when the key is turned to MAR to

if while travelling the warning lights comes

on either steady or blinking (along with a

message on the display). The operation

of the

warning light may be checked

by the traffic police using specific devices.

Comply with the laws and regulations of

the country where you are driving.

80

WARNING LIGHTS AND MESSAGES

The warning light switches on together with (where the instrument panel permits) a specific message and/or acoustic warning.

These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the

information contained in the Owner Handbook, which you are advised to read carefully in all cases. In the event of a failure

indication, always refer to the contents of this chapter.

WARNING The failure indicators appearing on the display are divided into two categories: very serious and less serious failures.

Serious faults are indicated by a repeated and prolonged warning "cycle". Less serious faults are indicated by a warning "cycle"

with a shorter duration. The display cycle of both categories can be interrupted by pressing the

SET button. The warning

light (or the symbol on the display) on the instrument panel will stay on until the cause of the failure is eliminated.

81

WARNING LIGHTS ON INSTRUMENT PANEL

Red warning lights

Warning lights on panel

What it means

What to do

LOW BRAKE FLUID/HANDBRAKE ENGAGED

The warning light switches on when the key is turned

to MAR-ON, but it should switch off after a few

seconds.

Low brake fluid level

The warning light turns on when the level of the brake

fluid in the reservoir falls below the minimum level,

possibly due to a leak in the circuit. On some versions

the display shows the dedicated message.

Restore the brake fluid level, then check that the

warning light has switched off.

46)

red

Handbrake engaged

The warning light switches on when the handbrake is

engaged.

On some versions, an acoustic tone accompanies the

warning light when the vehicle is moving.

If the warning light comes on while driving, check that

the handbrake is not on.

Release the handbrake, then check that the warning

light has switched off.

If the warning light stays on, contact a Fiat Dealership.

EBD FAILURE

The simultaneous switching on of the

(red),

red

(amber) and (amber) warning lights with the engine

on, indicates either a fault of the EBD system or that

the system is not available. In this case, the rear

wheels may suddenly lock and the vehicle may swerve

when braking sharply.

On some versions the display shows the dedicated

message.

Drive very carefully to the nearest Fiat Dealership to

have the system inspected immediately.

amber

82

Warning lights on panel

What it means

What to do

AIRBAG FAILURE

The warning light switches on when the ignition key

is turned to MAR, but it should switch off after a few

seconds.

The warning light stays on constantly if there is a

failure in the airbag system.

47) 48)

red

On some versions the display shows the dedicated

message.

SEAT BELTS REMINDER

(for versions/markets, where provided)

The warning light switches on fixed with the vehicle

stationary and the seat belt on passengers side (for

versions/markets, where provided) not fastened.

The warning light will flash and a buzzer will sound

if the seat belts on the driver's side, the passenger

side and the rear seats (for versions/markets, where

provided) are not correctly fastened with the vehicle in

motion.

The buzzer of the S.B.R. (Seat Belt Reminder) system

can only be disabled by a Fiat Dealership.

On some versions, the system may be reactivated using

the Setup menu.

red

COMFORT-MATIC/DUALOGIC TRANSMISSION

FAILURE

(for versions/markets, where provided)

When the key is turned to MAR, the warning light

switches on but it should switch off after a few

seconds.

The warning light flashes (together with a message in

the display and an acoustic signal) to indicate that the

gearbox is faulty.

If the transmission is faulty, contact a Fiat Dealership as

soon as possible to have the system checked.

red

The warning light can switch on even in the case

of transmission overheating, after a particularly

demanding use. In this case an engine performance

limitation is carried out.

83

Warning lights on panel

What it means

What to do

In normal driving conditions: stop the vehicle, switch

off the engine and check that the water level in the

reservoir is not below the MIN mark. In this case, wait

for a few minutes to allow the engine to cool down,

then slowly and carefully open the cap. Top up with

coolant fluid making sure that it is included between the

MIN and MAX lines on the vessel. Also check visually

for any fluid leaks. If, when restarting, the warning light

switches on again, contact a Fiat Dealership.

If the vehicle is used under demanding conditions (e.g.

towing trailers uphill or fully loaded): slow down and,

if the light stays on, stop the vehicle. Wait for 2 or 3

minutes with the engine running and slightly accelerated

to further favour the coolant circulation. Then stop

the engine. Check that the coolant level is correct as

described above.

ENGINE COOLANT TEMPERATURE TOO HIGH

The warning light switches on when the ignition key

is turned to MAR, but it should switch off after a few

seconds. The warning light turns on when the engine

is overheated.

red

The display shows the dedicated message.

Over demanding routes, it is advisable to keep the

engine on and slightly accelerated for a few minutes

before switching it off.

LOW BATTERY CHARGE

The warning light switches on when the ignition key is

turned to MAR, but it should switch off as soon as the

engine has started (with the engine idling a brief delay

before switching off is acceptable).

On some versions the display shows the dedicated

message.

If the warning light stays on, contact a Fiat Dealership

immediately.

red

INSUFFICIENT ENGINE OIL PRESSURE/ENGINE OIL

DETERIORATED

When the key is turned to MAR the warning light

comes on, but should go out as soon as the engine is

started.

84

Warning lights on panel

What it means

What to do

Steady light: Insufficient engine oil pressure

The warning light comes on fixed, together with a

message on the display (for versions/markets, where

provided) when the system detects insufficient engine

oil pressure.

49)

On blinking: Engine oil deteriorated

(for Multijet versions only)

The warning light starts to flash together with a

message on the display (for versions/markets, where

provided) when the system detects that the engine oil

has deteriorated.

If the warning light flashes, this does not mean that the

vehicle is faulty, but simply informs the driver that it is

now necessary to change the engine oil as a result of

regular vehicle use. If the oil is not changed, warning

Contact a Fiat Dealership as soon as possible.

12)

Remember that the deterioration of the engine oil is

accelerated by:

– mainly town use of the vehicle which makes the DPF

regeneration process more frequent

– use of the vehicle for short trips, preventing the

engine from reaching operating temperature

– repeated interruption of the regeneration process,

signalled by the DPF warning light coming on.

red

light

will also come on and engine operation is

limited to 3000 rpm when a second threshold is

reached.

If the oil is still not changed, when a third deterioration

threshold is reached, the engine is limited to 1500 rpm

to avoid damage.

LOW ENGINE OIL LEVEL

When turning the ignition key to MAR, the warning

light turns on but it should go off after a few seconds.

This warning light appears on the panel when the

engine oil level falls below the minimum recommended

value.

Restore the correct engine oil level (see “Checking fluid

levels” in the "Servicing and care" section).

red

On certain versions a dedicated message is displayed.

85

Warning lights on panel

What it means

What to do

DOORS OPEN

On certain versions, the warning light turns on when

one or more doors or the boot are not properly

closed.

Check that all doors or the boot (for versions/markets,

where provided) are perfectly closed.

On some versions the display shows the dedicated

message.

red

POWER STEERING FAILURE

When the ignition key is turned to MAR the warning

light on the dial turns on, but it should turn off after a

few seconds.

If the warning light stays on together with the message Contact a Fiat Dealership.

shown on the display and an acoustic signal, the

power steering is ineffective and the effort on the

steering wheel increases significantly even though the

vehicle can be steered.

red

WARNING

46) If the warning light turns on when travelling (on certain versions together with the message on the display) stop the vehicle immediately

and contact Fiat Dealership.

47) If, when the ignition key is turned to MAR, the warning light

does not switch on or stays on while driving, a failure may have occurred in

the restraint systems. In this case the airbags or pretensioners may not be deployed in an impact or, in a lower number of cases, they may be

deployed accidentally. Before continuing, contact a Fiat Dealership immediately to have the system checked.

48) The failure of the

on in the display. In this case, the

contact a Fiat Dealership to have the system checked immediately.

warning light is indicated by the

warning light flashing or, depending on the version, by the

icon constantly

warning light may not indicate a possible problem with the airbag restraint system. Before continuing,

49) If the warning light

turns on whilst driving (on certain versions together with the message on the display) stop the engine immediately

and contact a Fiat Dealership.

86

IMPORTANT

12) If the warning light switches on, the degraded engine oil must be changed as soon as possible, and never more than 500 km from the first

time that the warning light switches on. Failure to observe the above may result in severe damage to the engine and invalidate the warranty.

The activation of this warning light is not related to the amount of oil in the engine. Therefore, never top up with oil when the warning light

starts flashing.

87

Amber warning lights

What it means

What to do

INJECTION SYSTEM FAULT (Multijet versions) - EOBD

ENGINE CONTROL SYSTEM FAULT (petrol versions)

In normal conditions, when the ignition key is turned

to MAR the warning light switches on, but it should

switch off as soon as the engine is started.

13)

Injection system failure

(Multijet versions)

If the warning light stays on or comes on when

travelling, it means there is a fault in the injection

system which could cause loss of performance, poor

handling and high fuel consumption levels.

On some versions the display shows the dedicated

message.

Under these conditions, the vehicle can continue

travelling at moderate speed without demanding

excessive effort from the engine. Prolonged use of the

vehicle with the warning light on may cause damage.

amber

88

What it means

What to do

EOBD engine management system failure

(petrol versions)

This indicates that the warning light is working

correctly.

If the warning light stays on or turns on when

travelling:

fixed: this means there is a fault in the

supply/ignition system which could cause high exhaust

emissions, loss of performance, poor handling and

high fuel consumption levels. On some versions the

display shows the dedicated message. Under these

conditions, the vehicle can continue travelling at

moderate speed without demanding excessive effort

from the engine. Prolonged use of the vehicle with the

warning light on may cause damage.

If the light is fixed, contact a Fiat Dealership as

soon as possible. The warning light switches off if

the malfunction disappears, but is still stored by the

system.

If the light is blinking: continue the journey at moderate

speed, trying to avoid driving conditions that may cause

further flashing and contact a Fiat Dealership as soon

as possible.

amber

blinking: this indicates possible damage to the

catalytic converter (see “EOBD system” in the

“Knowing the instrument panel” chapter). If the light is

on and blinking, release the accelerator pedal to lower

the speed of the engine until the warning light stops

flashing.

Contact a Fiat Dealership as soon as possible.

UREA INJECTION SYSTEM FAILURE (Diesel versions) If the problem is not solved, a specific message will

The warning light switches on, together with a

dedicated message on the instrument panel (for

versions/markets, where provided) if a fluid not

conforming with the nominal characteristics is poured

in or if average UREA consumption over 50% is

detected.

appear on the instrument panel display whenever a

certain threshold is reached until it will no longer be

possible to start the engine.

When 200 km will remain to prevent the engine restart,

a continuous dedicated message will appear on the

dashboard (for versions/markets, where provided)

accompanied by an acoustic warning sound.

amber

89

What it means

What to do

ABS FAILURE

The warning light switches on when the ignition key

is turned to MAR, but it should switch off after a few

seconds.

The warning light will light up when the system is

either not working or not available. In this case the

braking system maintains its efficiency unaltered but

without the advantage of the ABS system.

On some versions the display shows the dedicated

message.

Drive carefully and contact a Fiat Dealership as soon as

possible.

amber

FUEL RESERVE

The warning light switches on when the ignition key

is turned to MAR, but it should switch off after a few

seconds. The warning light turns on when about 6 - 7

litres of fuel are left in the tank.

The warning light will blink to indicate a system fault.

If this is the case, go to a Fiat Dealership to have the

system checked.

amber

The triangle on the right side of the

symbol

indicates the side of the vehicle with the fuel filler.

PLUG PREHEATING (Multijet versions) - PLUG

PREHEATING FAULT (Multijet versions)

Glow plugs

(Multijet versions)

This warning light switches on when the key is turned

to MAR. It will switch off as soon as the glow plugs

have reached a preset temperature.

WARNING When it is particularly warm outside, the

warning light stays on for an extremely short time.

Start the engine as soon as the warning light switches

off.

amber

Glow plug preheating failure

(Multijet versions)

The warning light flashes if there is a fault in the

preheating system.

Contact a Fiat Dealership as soon as possible.

On some versions the display shows the dedicated

message.

90

What it means

What to do

WATER IN DIESEL FILTER (Multijet versions)

The warning light switches on when the ignition key

is turned to MAR, but it should switch off after a few

seconds.

14)

The warning light

switches on to indicate the

presence of water in dated the diesel filter.

On some versions the display shows the dedicated

message.

amber

INDICATION OF DIESEL EMISSIONS ADDITIVE LOW

LEVEL (UREA)

(for versions/markets, where provided)

The Diesel Emissions Additive (UREA) low level

warning light

of UREA.

lights up if the vehicle has a low level

VEHICLE PROTECTION SYSTEM FAULT - FIAT

CODE - ALARM FAULT (for versions/markets, where

provided - amber) - BREAK-IN ATTEMPT

Fiat CODE Vehicle protection system fault

If, with the ignition key at MAR, the warning light

stays on permanently, this indicates a possible failure

(see “Fiat Code system” in the “Know your vehicle”

section).

On some versions the display shows the dedicated

message.

Contact a Fiat Dealership to have all the keys stored in

the memory.

amber

WARNING Warning lights

the same time to indicate a Fiat CODE system failure.

If with the engine running the warning light flashes,

and

will come on at

the vehicle is not protected by the engine immobiliser

(see “Fiat Code system Running section “Know your

vehicle”).

91

What it means

What to do

Alarm fault

(for versions/markets, where provided)

A fault with the alarm system is signalled by this

Contact a Fiat Dealership as soon as possible.

warning light

(or symbol in the display) coming on.

A specific message is displayed on certain versions.

Break-in attempt

amber

The warning light will blink rapidly or the symbol will

appear on the display to indicate a break-in attempt.

A specific message is displayed on certain versions.

Contact a Fiat Dealership as soon as possible.

GENERAL FAILURE INDICATION

The warning light turns on in the following

circumstances:

Engine oil pressure sensor failure

The warning light switches on when an engine oil

pressure sensor anomaly is detected.

Contact a Fiat Dealership as soon as possible to have

the fault fixed.

Exterior lights failure:

On certain versions, the warning light will come

on when a failure to one of the following lights is

detected:

amber

side lights;

brake lights;

rear fog lamps;

The failure relating to these lights could be: one or more

blown bulbs, a blown protection fuse or a break in the

electrical connection.

direction indicators;

number plate lights.

On some versions the display shows the dedicated

message.

Fuel cut-off inertia switch tripped

The warning light switches on when the fuel cut-off

inertia switch is tripped. The display shows the

dedicated message.

amber

92

What it means

Parking sensor failure

(for versions/markets, where provided)

See parking sensor warning light section.

What to do

In this case, the

warning light may not indicate a

possible problem with the airbag restraint system.

Before continuing, contact a Fiat Dealership to have the

system checked immediately.

Airbag failure warning light

The warning light

a failure of the warning light

warning light may not indicate a possible problem with

the airbag restraint system.

turns on and flashes to indicate

Before continuing, contact a Fiat Dealership to have the

system checked immediately.

. In this case, the

amber

Start&Stop system failure

(for versions/markets, where provided)

In this case, contact the Fiat Service Network as soon

as possible

The warning light

comes on alternatively to the

warning light when a Start&Stop system fault is

detected.

93

What it means

What to do

DPF (PARTICULATE FILTER) CLEANING UNDERWAY

(for versions/markets, where provided)

The warning light switches on when the ignition key

is turned to MAR, but it should switch off after a few

seconds.

The warning light switches on constantly to inform

the driver that the DPF system needs to eliminate

the trapped pollutants (particulate) through the

regeneration process.

A specific message will appear on the display when

the warning light comes on (for versions/markets,

where provided).

WARNING Failure to follow the required

procedure when the DPF warning light comes on

for a mileage equal to or greater than 30 km or

for a cumulative time equal to or greater than 2

The warning light does not come on during every DPF

regeneration, but only when driving conditions require

that the driver is notified. The warning light will go off

if the vehicle stays in motion until regeneration has

been completed. The process normally takes about 15

minutes.

Optimum conditions for completing the process are

achieved by travelling at 60 km/h with engine revs

above 2000 rpm. If this warning light comes on, it does

not mean the vehicle is defective, so there is no need to

take it to a garage.

amber

50) 51)

hours, may result in the warning light

on with consequent damage to the DPF device.

Remember that if the warning light is on, it

coming

is necessary to go to the Fiat Dealership to

restore the correct function of the DPF.

ESC SYSTEM

ESC system activation

Flashing of the warning light while driving indicates the

intervention of the ESC system.

ESC system failure

The warning light switches on when the ignition key

is turned to MAR, but it should switch off after a few

seconds.

amber

If the warning light does not go out or remains on whilst

driving, go to a Fiat Dealership.

The display will show a dedicated message.

94

What it means

HILL HOLDER FAILURE

What to do

(for versions/markets, where provided)

When the key is turned to MAR, the warning light

switches on, but it should switch off after a few

seconds; the warning light indicates a Hill Holder

system failure.

In this case, contact the Fiat Dealership as soon as

possible.

amber

The display will show a dedicated message.

iTPMS

iTPMS failure/iTPMS temporarily deactivated

The warning light flashes for about 75 seconds then

stays on constantly when a fault is detected in the

iTPMS.

In this case, contact the Fiat Dealership as soon as

possible.

Low tyre pressure

In this case it is advisable to restore the correct

pressure value.

WARNING Do not continue driving with one or more flat

tyres as vehicle handling may be compromised. Stop

the vehicle, avoiding sharp braking and steering.

The warning light switches on to indicate that the

tyre pressure is lower than the recommended

value and/or that a pressure loss is occurring. In

these circumstances, optimal tyre duration and fuel

consumption may not be guaranteed.

amber

BRAKE PAD WEAR

The warning light switches on if the front brake pads

are worn.

Have them replaced as soon as possible.

On certain versions a dedicated message is displayed.

amber

PARKING SENSOR FAILURE

(for versions/markets, where provided)

The warning light turns on when a parking sensor fault

In this case, contact the Fiat Dealership as soon as

possible.

is detected. On certain versions the

warning light

comes on instead. On certain versions a dedicated

message is displayed.

95

What it means

What to do

START&STOP SYSTEM FAILURE

(for versions/markets, where provided)

The warning light comes on when a fault is detected

in the Start&Stop system. On certain versions the

warning light comes on instead. On certain versions a

dedicated message is displayed.

In this case, contact the Fiat Dealership as soon as

possible.

amber

ASR SYSTEM DEACTIVATED

The ASR system can be turned off by pressing the

button ASR OFF. The warning light switches on to

warn the driver that the system is off. If the ASR OFF

button is pressed again, the warning light will switch

off to inform the driver that the system is on again.

TRACTION PLUS SYSTEM ACTIVATION

(for versions/markets, where provided)

The warning light switches on when the Traction Plus

system is activated by pressing the T+ button on the

dashboard. The LED on the button turns on.

Traction Plus system failure

Turning the key to the MAR position, if the warning

light stays on or lights up when travelling with the LED

amber

In this case, contact the Fiat Dealership as soon as

possible.

on the button and the warning light

.

The display will show a specific message.

REAR FOG LIGHTS

The warning light comes on when the rear fog lights

are turned on.

96

WARNING

50) During regeneration, the fan could be operated.

51) Always drive at a speed appropriate to the traffic conditions, the weather and traffic regulations. The engine may be stopped if the

DPF light is on; however, repeated interruption of the regeneration process may result in premature deterioration of the engine oil. For this

reason, always wait until the warning light switches off before stopping the engine as described above. It is not advisable to complete DPF

regeneration with the vehicle stationary.

IMPORTANT

13) Go to a Fiat Dealership as soon as possible if the warning light

does not light up when the key is turned to MAR or if while travelling the

warning

warning light switches on or flashes (along with a message and a symbol on the display on some versions). The operation of the

light may be checked by the traffic police using specific devices. Comply with the laws and regulations of the country where you are driving.

14) The presence of water in the fuel supply circuit may cause severe damage to the injection system and irregular engine operation. If the

warning light switches on (on some versions together with the dedicated message on the display), contact a Fiat Dealership as soon as

possible to have the system bled. If the above indication occurs immediately after refuelling, water may have entered the tank: turn the engine

off immediately and contact a Fiat Dealership.

97

Green warning lights

Warning lights on panel

What it means

What to do

SIDE LIGHTS - FOLLOW ME HOME

Side lights

The warning light switches on when the side lights are

activated.

Follow Me Home

The warning light will turn on when this device is active

(see the “Follow me home device” paragraph in the

“Know your vehicle” section). The display shows the

dedicated message.

green

LEFT-HAND DIRECTION INDICATOR (blinking)

The warning light switches on when the direction

indicator control stalk is moved downwards or,

together with the right direction indicator, when the

hazard warning light button is pressed.

RIGHT-HAND DIRECTION INDICATOR (blinking)

The warning light switches on when the direction

indicator control stalk is moved upwards or, together

with the left direction indicator, when the hazard

warning light button is pressed.

green

FOG LIGHTS

The warning light comes on when the front fog lights

are turned on.

CRUISE CONTROL

The warning light turns on together with the message

on the display when turning the ring of the Cruise

Control to ON.

98

Blue warning lights

Warning lights on

panel

What it means

What to do

MAIN BEAM HEADLIGHTS

The warning light switches on when the main beam

headlights are turned on.

blue

99

MESSAGES ON THE DISPLAY

What it means

What to do

GEAR SHIFT INDICATION

(for versions/markets, where provided)

On vehicles with a manual transmission, the gear shift

indicator suggests gear changes to the driver (SHIFT

UP or SHIFT DOWN) via a special display on the

instrument panel. This suggestion to change gear is

designed to improve consumption and ensure the best

driving style.

NOTE The indication in the instrument panel remains

on until the driver shifts gear or the driving conditions

go back to a situation where gearshifting is not

required to improve consumption.

START&STOP SYSTEM ACTIVATION

The symbol lights up on the display when the engine

is stopped automatically (for versions/markets, where

provided).

100

What it means

What to do

INDICATION OF DIESEL EMISSIONS ADDITIVE LOW

LEVEL (UREA)

When low UREA level is detected, a text message will

appear on the instrument panel display, together with

the symbol

up.

to indicate that UREA must be topped

The symbol

stays on until the tank is topped up

with at least 5 litres of UREA.

If you do not top up, a specific message will appear

on the instrument panel display whenever a certain

threshold is reached until it will no longer be possible

to start the engine.

A message appears continuously on the display

when the residual range is approximately 200 km

accompanied by an auditory indication.

When the residual range is 0 km, a specific message

will appear on the display (for versions/markets, where

provided). It will no longer be possible to restart the

engine after it has been stopped.

Top up the UREA tank as soon as possible with at least

5 litres of UREA. If topping up is done with remaining

range of UREA in the tank equal to zero, you may need

to wait two minutes before starting the vehicle.

It will be possible to restart the engine after pouring at

least 5 litres of UREA in the tank.

52)

NATURAL POWER SYSTEM FAILURE

All Methane fuel levels disappear on the display and

the symbol appears with a dedicated message.

In this case, contact the Fiat Dealership as soon as

possible.

FIAT CODE SYSTEM FAILURE

The symbol switches on or blinks to indicate a failure

or fault of the Fiat CODE system.

Contact a Fiat Dealership as soon as possible.

AIRBAG WARNING LIGHT FAILURE

The symbol switches on to indicate a failure of the

warning light

on the display.

101

What it means

What to do

PETROL OPERATION (Natural Power versions)

The symbol appears on the display, with all the bar

edges, if the methane is running out (Natural Power

versions). In these cases the system automatically

switches to petrol operation.

MESSAGES ON DISPLAY (COMFORT-

MATIC/DUALOGIC™ TRANSMISSION)

A message appears on the display in the following

cases:

incorrect use of the transmission by the driver;

manual method unavailable;

automatic mode not available;

clutch overtemperature;

starting without pressing the brake pedal;

gear unavailable;

operation not admissible;

shifting without pressing the brake pedal;

neutral engagement request (N);

WARNING

52) When the UREA tank is empty and the engine is stopped it is no longer possible to restart it until the UREA tank is topped up with at least

5 litres of UREA.

102

Knowing the Instrument Panel for Your Fiat Fiorino SUV Third Generation (2015-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals