2013-2023 Fiat Panda SUV SAFETY -> PRE-TENSIONERS User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

SAFETY -> PRE-TENSIONERS for Your Fiat Panda SUV Third Generation (2013-2023)

Warning light  
What it means  
Parking sensor failure  
(for versions/markets, where provided)  
The warning light switches on, on some versions along with a dedicated message on the display, when a  
fault is detected in the parking sensors.  
Exterior lights failure  
(for versions/markets, where provided)  
The warning light switches on when a fault is detected in one of the following lights: side lights, number  
plate lights, rear fog lights, direction indicators, daytime running lights (DRL).  
Engine oil pressure sensor failure  
(for versions/markets, where provided)  
The engine oil pressure sensor failure is indicated by the activation of the warning light on the instrument  
panel.  
ELD system failure (for versions/markets, where provided)  
The warning light switches on, on some versions along with a dedicated message on the display, when a  
fault is detected in the 4x4 drive. Contact a Fiat Dealership as soon as possible.  
Water in diesel filter (diesel versions)  
(for versions/markets, where provided)  
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few  
seconds. The warning light switches on when water is detected in the diesel filter. On certain versions a  
dedicated message is displayed.  
27)  
WARNING  
27) If the  
warning light switches on (on some versions together with the dedicated message on the display), contact a Fiat Dealership as  
soon as possible to have the system bled. If the warning appears immediately after refuelling, water may have entered the tank: turn the  
engine off immediately and contact a Fiat Dealership.  
51  
Warning light  
What it means  
iTPMS  
(for versions/markets, where provided)  
Tyre pressure low  
The warning light switches on constantly to indicate that the tyre pressure is lower than the recommended  
value, in order to guarantee long tyre life and low fuel consumption, or to indicate a slow loss of pressure.  
In this way the iTPMS warns the driver that one or more tyres may be flat and probably punctured. In this  
case it is advisable to restore the correct pressure value. Once the normal operating conditions of the  
vehicle are restored, carry out the Tyre reset procedure.  
IMPORTANT Do not continue driving with one or more flat tyres as handling may be compromised. Stop  
the vehicle, avoiding sharp braking and steering.  
iTPMS failure/iTPMS temporarily deactivated  
The warning light flashes for about 75 seconds and then stays on constantly (along with a dedicated  
message on the display) to indicate that the system is temporarily deactivated or faulty. The system goes  
back to normal operation when the operating conditions allow it. If this is not the case, carry out the Tyre  
reset procedure after restoring the normal operating conditions.  
If the malfunction warning persists, contact a Fiat Dealership as soon as possible.  
LPG FUEL RESERVE  
(for versions/markets, where provided)  
The warning light switches on when the residual quantity of LPG drops below 1/5 of the tank capacity. On  
certain versions a dedicated message is displayed.  
METHANE RESERVE (Natural Power versions)  
The warning light switches on when the residual quantity of Methane drops below 1/5 of the tank capacity.  
On certain versions a dedicated message is displayed.  
52  
Green warning lights  
Warning light  
What it means  
ELD SYSTEM (for versions/markets, where provided)  
The warning light on flashing indicates activation of the electronic locking differential (ELD) function.  
GRAVITY CONTROL SYSTEM (Panda Cross 4x4 versions)  
The warning light on constantly, along with a dedicated message on the display, indicates activation of the  
Gravity Control function. Deactivation of the function is signalled by flashing of the warning light, by an  
acoustic warning and by a dedicated message on the display.  
PETROL/LPG SWITCHING  
(for versions/markets, where provided)  
Warning light on constantly: petrol operation.  
Warning light off: LPG operation.  
PETROL/METHANE SWITCHING  
(for versions/markets, where provided)  
Warning light on constantly: petrol operation.  
Warning light off: Methane operation.  
FOG LIGHTS  
The warning light comes on when the front fog lights are turned on.  
SIDE LIGHTS AND DIPPED BEAM HEADLIGHTS/FOLLOW ME HOME  
Side lights and dipped beam headlights  
The warning light switches on when the side lights or dipped headlights are turned on.  
Follow Me Home  
The warning light comes on, on some versions along with a dedicated message on the display, when the  
"Follow me home" device is used.  
53  
Warning light  
What it means  
LEFT DIRECTION INDICATOR  
The warning light turns on when the direction indicator control lever is moved downwards or, together with  
the right indicator, when the hazard warning light button is pressed.  
RIGHT DIRECTION INDICATOR  
The warning light turns on when the direction indicator control lever is moved upwards or, together with the  
left indicator, when the hazard warning light button is pressed.  
Blue warning lights  
Warning light  
What it means  
MAIN BEAM HEADLIGHTS  
The warning light switches on when the main beam headlights are turned on.  
Symbols and messages on the display  
Symbol or message  
What it means  
The symbol is displayed, along with a dedicated message, in the event of an LPG system failure.  
In this case, contact a Fiat Dealership as soon as possible, running on petrol  
The symbol is displayed, along with a dedicated message, in the event of a methane supply system failure.  
In this case, contact a Fiat Dealership as soon as possible, running on petrol  
54  
Symbol or message  
What it means  
FUEL LEVEL SENSOR FAILURE  
The symbol appears and all the notches disappear in the event of fuel gauge sensor failure. Contact a Fiat  
Dealership as soon as possible.  
The message is displayed when the Start&Stop system is activated/deactivated by pressing the  
in the central part of the dashboard.  
button  
START&STOP  
(For versions/markets, where  
provided)  
With the Start&Stop system on, the LED on the button is off; if the system is deactivated the LED comes  
on.  
GRAVITY CONTROL  
The activation, activation not permitted and deactivation of the Gravity Control system are shown on the  
display.  
(Panda Cross 4x4 versions)  
When the next scheduled service is approaching, the word “Service” appears on the display, followed by  
the number of kilometres or miles left. This is displayed automatically, with ignition key at MAR-ON, 2000  
km (or equivalent value in miles) before servicing or, where provided, 30 days before servicing. It is also  
displayed each time the key is turned to MAR-ON or, for versions/markets, where provided, every 200 km  
(or equivalent value in miles).  
SERVICE  
Go to a Fiat Dealership, where the "Scheduled Servicing Plan" operations will be performed and the  
message will be reset.  
55  
Symbol or message  
What it means  
For versions equipped with "Dualogic" gearbox, the following messages can be displayed:  
Reduce gear changes  
Manual method unavailable  
Automatic method unavailable  
Clutch overheating  
Depress brake pedal  
DUALOGIC TRANSMISSION  
Depress brake pedal - delayed ignition  
Gear unavailable  
Operation not admissible  
Depress brake pedal and repeat operation  
Positioning of the gear lever at N (neutral).  
28) 29)  
WARNING  
28) If the messages remain on the display, contact the Fiat Dealership.  
29) In order to safeguard the efficiency of the clutch, do not use the accelerator to keep the car stationary (e.g. when standing uphill); if the  
clutch overheats it could damage it; use the brake pedal instead and only use the accelerator pedal when you decide to set off.  
56  
SAFETY  
The chapter that you are about to read  
is very important: it describes the  
safety systems with which the vehicle is  
equipped and provides instructions on  
how to use them correctly  
ACTIVE SAFETY SYSTEMS ............ 58  
DRIVING ASSISTANCE SYSTEMS .. 64  
OCCUPANT PROTECTION  
SYSTEMS ....................................... 68  
SEAT BELTS ................................... 68  
SBR (SEAT BELT REMINDER)  
SYSTEM ......................................... 70  
PRE-TENSIONERS ......................... 71  
CHILD PROTECTION SYSTEMS..... 73  
SUPPLEMENTARY RESTRAINT  
SYSTEM (SRS) - AIRBAG................ 83  
57  
44) 45) 46) 47) 48) 49) 50) 51) 52)  
HH (Hill Holder) SYSTEM  
ACTIVE SAFETY  
SYSTEMS  
This system is an integral part of the  
ESC system and facilitates starting on  
slopes.  
ESC (Electronic Stability  
Control) SYSTEM  
(for versions/markets, where provided)  
ABS (Anti-lock Braking  
System)  
It is automatically activated in the  
following conditions:  
This is an electronic system that  
controls car stability in the event of loss  
of tyre grip, helping maintain directional  
control. The system is capable of  
recognising potentially dangerous  
situations in terms of the stability and  
intervenes automatically on the brakes  
in a differentiated manner for the four  
wheels in order to provide a stabilising  
torque.  
This system, which is an integral part of  
the braking system, prevents one or  
more wheels from locking and slipping  
in all road surface conditions,  
uphill: vehicle stationary on a road  
with a gradient higher than 5%, engine  
running, brake pressed and  
transmission in neutral or gear other  
than reverse engaged;  
irrespective of the intensity of the  
braking action, ensuring that the car  
can be controlled even during  
downhill: car stationary on a road  
with a gradient of more than 5%,  
engine running, brake pressed and  
reverse gear engaged.  
emergency braking.  
The ESC system switches on  
automatically when the engine is  
started and cannot be switched off.  
IMPORTANT To obtain the maximum  
efficiency of the braking system, a  
bedding-in period of about 500 km is  
needed: during this period it is better to  
avoid sharp, repeated and prolonged  
braking.  
When setting off, the ESC system  
control unit maintains the braking  
pressure on the wheels until the torque  
necessary for starting is reached, or  
in any case for a maximum of 2  
seconds, allowing your right foot to be  
moved easily from the brake pedal to  
the accelerator.  
System intervention  
The intervention of the system is  
indicated by the flashing of the ESC  
warning light on the instrument panel,  
to inform the driver that the vehicle is in  
critical stability and grip conditions.  
The ABS also integrates the following  
systems: EBD (Electronic Braking Force  
Distribution), MSR (Motor  
When the 2 seconds have elapsed,  
without starting, the system is  
automatically deactivated, gradually  
releasing the braking pressure. During  
this release stage, the typical  
Schleppmoment Regelung) and MBA  
(Mechanical Brake Assist) (for  
versions/markets, where provided).  
53) 54) 55) 56) 57) 58)  
System intervention  
mechanical brake release noise can be  
heard, indicating that the car is about  
to move.  
The driver can feel that the ABS system  
has come into action because the  
brake pedal pulsates slightly and the  
system gets noisier: this is entirely  
normal with the system operating.  
NOTE: The Hill Holder system is not  
active with the handbrake engaged.  
58  
IMPORTANT The Hill Holder system is  
not a parking brake, therefore do not  
leave the vehicle without activating the  
handbrake, switching off the engine,  
and engaging first gear, with the vehicle  
parked in safe conditions.  
HBA (Hydraulic Brake  
Assist) system  
The HBA system is designed to  
improve the cars braking capacity  
during emergency braking. The system  
detects an emergency braking by  
monitoring the speed and strength with  
which the brake pedal is pressed,  
thereby applying the optimal brake  
pressure.  
ASR (AntiSlip  
Regulation) SYSTEM  
It is an integral part of the ESC system.  
It is automatically activated in the case  
of drive wheels slipping, loss of grip  
on wet roads (aquaplaning) and  
acceleration on slippery, snowy or icy  
roads, etc.  
F1D0038  
49  
This can reduce the braking distance:  
the HBA system therefore completes  
the ABS.  
On some versions, the intervention of  
the system is indicated by a dedicated  
message shown on the display. When  
the system is not active, the LED on the  
button ASR OFF turns on and, on  
some versions, a message appears on  
the display.  
Maximum assistance from the HBA  
system is obtained pressing the brake  
pedal very quickly. In addition, the  
brake pedal must be pressed  
continuously during braking, avoiding  
intermittent presses, to benefit from the  
system.  
Depending on the slipping conditions,  
two different control systems are  
activated:  
if the slipping involves both drive  
wheels, the ASR intervenes reducing  
the power transmitted by the engine;  
When the ASR is deactivated while  
driving, the next time the car is started  
the ASR is automatically activated.  
When travelling on snowy roads with  
snow chains, it may be helpful to turn  
the ASR off: in fact, in these conditions,  
the driving wheels skidding when  
setting off gives you better traction.  
Do not reduce pressure on the brake  
pedal until braking is no longer  
necessary.  
if the slipping only involves one  
of the drive wheels, it intervenes  
automatically braking the wheel that is  
slipping.  
The HBA system is deactivated when  
the brake pedal is released.  
Engagement/disengagement of the  
system  
64) 65) 66)  
59) 60) 61) 62) 63)  
The ASR is switched on automatically  
each time the engine is started.  
While driving, the ASR can be switched  
off and subsequently switched on  
again by pressing the ASR OFF button  
fig. 49.  
59  
ELD (Electronic Locking  
Differential) SYSTEM  
(Panda Cross 4x4 and Panda 4x4  
versions)  
If the space-saver wheel is used  
If the space-saver wheel is used, the  
control unit for 4x4 drive detects its  
presence (via the wheel speed signals)  
and reduces the intervention of the  
four-wheel drive mode to a minimum,  
while guaranteeing the agility of the  
vehicle. No fault/alarm signal is  
displayed on the instrument panel or on  
the display.  
The ELD system allows the drive force  
to be evenly distributed over the same  
axle when one or both wheels are  
slipping. The ELD acts by braking the  
wheels with poor grip (or those slipping  
more than the others), thereby  
transferring the drive force to those  
which have greater grip on the ground.  
The system operates at speeds below  
50 km/h. Above this speed, it is  
automatically deactivated and it is  
reactivated when the speed falls below  
50 km/h.  
F1D0122  
50  
Disabling the system  
To disable the system, press button A  
fig. 50 (Panda 4x4 versions) or turn  
the ring to the left fig. 51 (Panda Cross  
4x4 versions) and keep it in this position  
until LED 1 on the selector lights up.  
The activation of the ELD system  
involves the following functions being  
switched on:  
GRAVITY CONTROL  
SYSTEM  
(Panda Cross 4x4 versions)  
F1D0116  
inhibition of the ASR function, in  
order to fully exploit the engine torque;  
51  
IMPORTANT This function can be  
activated only with "Off Road" mode  
activated.  
System intervention  
differential lock effect on the front  
and rear axles, via the braking system,  
to improve drive on uneven surfaces.  
The  
warning light on the instrument  
panel flashes to signal that the system  
has intervened.  
It is an integral part of the ESC system  
and is aimed at keeping the vehicle at a  
constant speed during a descent,  
operating autonomously on the brakes  
in various ways at the same time. In this  
way, the Gravity Control function  
assists the driver on steep gradients in  
low-grip conditions and/or on rough  
terrain.  
Enabling the system  
To arrange operation of the ELD system  
press button A fig. 50 (Panda 4x4  
versions) or turn the ring fig. 51 to the  
right (Panda Cross 4x4 versions) and  
keep it in this position until LED 2  
on the selector lights up.  
60  
Noise and vibrations coming from the  
wheel sides (brakes) when the Gravity  
Control system is activated are normal.  
IMPORTANT The system does not  
relieve the driver of the responsibility of  
controlling the vehicle and does not  
replace attention while driving. The  
driver of the vehicle takes the complete  
responsibility for the consequences of  
their actions and of an incorrect and not  
responsible use of the vehicle.  
System intervention  
IMPORTANT On level ground in urban  
areas it is advisable to deactivate the  
Gravity Control system intervention  
set-up, since for speeds below 25 km/h  
in some usage conditions, such as  
when setting off, shifting gear and  
driving over road humps without using  
the accelerator pedal, the system might  
activate.  
You must travel at a speed slower than  
25 km/h for the system to activate.  
After reaching the desired speed,  
release the accelerator and brake  
pedals completely. If you want to  
increase/decrease the speed, press the  
accelerator/brake pedals again.  
IMPORTANT The system is also  
available for very low speeds between 5  
km/h and 9 km/h, but in this interval  
the gearbox must be set to neutral to  
prevent engine stalling.  
Disabling the system  
To deactivate the system, turn the ring  
fig. 52 to the left, keeping it in this  
position until LED 3 on the selector  
switches off.  
Enabling the system  
To arrange operation of the Gravity  
Control system, turn ring fig. 52, with  
LED 2 on, to the right, and keep it  
in this position until LED 3 on the  
IMPORTANT For speeds above 9 km/h,  
the Gravity Control system must be  
used with a gear that is suitable for the  
set speed, in order to prevent possible  
engine stalling. While the Gravity  
IMPORTANT If the braking system  
overheats the system will deactivate  
through a gradual release of the braking  
pressure, leaving vehicle control to the  
driver. Deactivation of the Gravity  
Control system is accompanied by  
selector lights up. The  
warning light  
comes on in the instrument panel and  
the dedicated message is displayed.  
Control system is operating it is also  
possible to take control of the vehicle  
again by pressing the brake and  
flashing of the  
warning light, by a  
dedicated message on the display and  
an acoustic warning. To reactivate  
the system intervention set-up wait for  
the system to cool down and turn  
the ring nut again.  
accelerator pedals. If the Gravity  
Control is not available when system  
intervention set-up is engaged, this  
could be due to brake overheating. In  
this case, wait for a few minutes.  
IMPORTANT The Gravity Control  
system is available for speeds between  
5 km/h and 25 km/h. It is advisable to  
use the system in low gears (first,  
second and third).  
F1D0116  
52  
IMPORTANT System intervention  
set-up can be engaged only with "Off  
Road" mode activated.  
61  
IMPORTANT The Gravity Control  
system is deactivated when exceeding  
25 km/h and at speeds lower than  
50 km/h it remains enabled to be  
reactivated when the speed returns  
under 25 km/h. In this case, the  
indication on the instrument panel is  
switched off and the LED on the ring  
stays on. If car speed exceeds 50  
km/h, the Gravity Control system  
completely deactivates and each  
individual action made by the system  
on the brakes is blocked. To reactivate  
it, turn the ring nut again when the  
speed is again below 25 km/h.  
Engagement/disengagement  
If the Traction Plus system is faulty, the  
ESC warning light on the instrument  
panel switches on constantly.  
The system is deactivated when  
starting. To activate the Traction Plus  
system, press the T+ button fig. 53: the  
LED on the button switches on; the  
display shows a dedicated message. To  
disengage the system press the T+  
button again.  
WARNING  
44) The ABS gets the most from the  
available grip, but it cannot improve it; you  
should therefore take every care when  
driving on slippery surfaces and not take  
unnecessary risks.  
45) When the ABS cuts in and you feel the  
brake pedal pulsating, do not remove  
your foot, but keep the pedal pushed  
down; in doing so you, will stop in the  
shortest distance possible under the road  
conditions at the time.  
T+ (Traction Plus)  
SYSTEM  
46) If the ABS system intervenes, this  
indicates that the traction of the tyres on  
the road is nearing its limit. You must slow  
down to a speed compatible with the  
available traction.  
(for versions/markets, where provided)  
Traction Plus is a driving aid, useful  
for setting off in poor grip conditions  
(snow, ice, mud, etc.) which allows the  
drive force to be distributed in the  
best way over the front axle when one  
wheel is slipping.  
F1D0039  
53  
Operation  
This function operates under a  
threshold of 30 km/h. Over this speed,  
it is automatically deactivated (the  
LED on the button is still on) and it is  
reactivated again when the speed  
is below 30 km/h.  
47) To obtain the maximum efficiency of  
the braking system, a bedding-in period of  
about 500 km is needed: during this period  
it is better to avoid sharp, repeated and  
prolonged braking.  
Traction Plus acts by braking the  
wheels with poor grip (or those slipping  
more than the others), thereby  
48) The ABS cannot overrule the natural  
laws of physics, and cannot increase  
the grip available according to the  
condition of the road.  
The activation of the Traction Plus  
system causes the differential locking  
effect on the front axle, through the  
braking system, to improve traction on  
irregular grounds.  
transferring the drive force to those  
which have greater grip on the ground.  
49) The ABS cannot prevent accidents,  
including those due to excessive speed on  
corners, driving on low-grip surfaces or  
aquaplaning.  
62  
50) The capability of the ABS must never  
be tested irresponsibly and dangerously, in  
such a way as to compromise personal  
safety and the safety of others.  
58) The capability of the ESC system must  
never be tested irresponsibly and  
dangerously, in such a way as to  
compromise personal safety and the safety  
of others.  
66) The HBA system is an aid for the driver,  
who must always pay full attention while  
driving. The responsibility always rests with  
the driver. The features of the HBA system  
must never be tested in imprudent or  
dangerous ways, with the possibility of  
putting the safety of the driver, occupants  
or other road users at risk.  
51) For the correct operation of the ABS,  
the tyres must of necessity be the same  
make and type on all wheels, in perfect  
condition and, above all, of the prescribed  
type and dimensions.  
59) For the correct operation of the ASR  
system, the tyres must of necessity be the  
same make and type on all wheels, in  
perfect condition and, above all, of the  
prescribed type and dimensions.  
52) When the Mechanical Brake Assist  
intervenes, noises may be heard from the  
system. This is normal. In any case, while  
braking keep the brake pedal firmly  
depressed.  
60) Do not take unnecessary risks, even if  
your vehicle is fitted with an ASR system.  
Your driving style must always be suited to  
the road conditions, visibility and traffic.  
The driver is, in any case, responsible for  
safe driving.  
53) For the correct operation of the ESC  
system, the tyres must necessarily be  
of the same make and type on all wheels,  
in perfect condition and, above all, of  
the prescribed type and size.  
61) The ASR cannot overrule the natural  
laws of physics, and cannot increase  
the grip available according to the  
condition of the road.  
54) The ESC functions even when the  
space-saver wheel is being used. Always  
remember that the space-saver wheel,  
being smaller than the original wheel,  
provides less grip.  
62) The ASR system cannot prevent  
accidents, including those due to excessive  
speed on corners, driving on low-grip  
surfaces or aquaplaning.  
55) ESC performance features must not  
induce the driver to take unnecessary  
or unfounded risks. Your driving style must  
always be suited to the road conditions,  
visibility and traffic. The driver is, in any  
case, responsible for safe driving.  
63) The capability of the ASR must never  
be tested irresponsibly and dangerously, in  
such a way as to compromise personal  
safety and the safety of others.  
64) The HBA system cannot increase tyre  
grip on the road over the limits imposed by  
laws of physics: always drive carefully  
according to the conditions of the road  
surface.  
56) The ESC system cannot alter the  
natural laws of physics, and cannot  
increase grip, which depends on the  
condition of the road.  
65) The HBA system cannot prevent  
accidents, including those due to excessive  
speed on bends, travelling on low-grip  
surfaces or aquaplaning.  
57) The ESC system cannot prevent  
accidents, including those due to excessive  
speed on corners, driving on low-grip  
surfaces or aquaplaning.  
63  
the vehicle speed is between 5 and  
30 km/h;  
Versions equipped with manual  
gearbox: at the end of the automatic  
braking the engine may stall and turn  
off, unless the driver presses the clutch  
pedal.  
DRIVING  
ASSISTANCE  
SYSTEMS  
the front seat belts are fastened.  
Anyway, the system can be deactivated  
(then reactivated) through the Setup  
Menu on the display.  
CBC (City Brake  
Control) system  
(for versions/markets, where provided)  
Versions equipped with "Dualogic"  
gearbox (for versions/markets, where  
provided): at the end of braking the last  
gear stored remains engaged.  
The system intervenes if there is risk of  
imminent collision and the driver does  
not press the brake pedal promptly.  
If the system detects that the vehicle  
ahead could be hit, it may prepare the  
vehicle to a possible emergency  
braking.  
67) 68) 69) 70) 71)  
30) 31) 32) 33) 34) 35) 36)  
This is a driving assistance system,  
which includes a laser sensor, located  
in the upper part of the windscreen  
fig. 54, that can detect the presence of  
nearby cars in front of the vehicle and,  
in the case of an imminent collision,  
intervenes automatically, braking the  
vehicle to prevent the impact or  
mitigate its effects.  
IMPORTANT Both on versions  
equipped with manual gearbox and on  
those with "Dualogic" gearbox (for  
versions/markets, where provided),  
after the vehicle is stopped the brake  
calipers may be stuck for about 2  
seconds for safety reasons. Make sure  
you press the brake pedal if the vehicle  
moves slightly forwards.  
If the driver does not carry out any  
action to prevent the collision, the  
system may automatically slow down  
the vehicle, in order to prepare it to  
a possible impact.  
When there is risk of impact, if the  
action on the brake pedal by the driver  
is not sufficient, the system may  
intervene in order to improve  
IMPORTANT The system does NOT  
activate when reverse is engaged. The  
system does NOT activate if the front  
seat belts are not fastened.  
the reaction of the braking system,  
therefore reducing vehicle speed  
further.  
Engagement/disengagement  
When driving uphill on a steep slope,  
the system may intervene, activating  
the braking system.  
The system can be deactivated (then  
reactivated) through the Setup Menu on  
the display.  
Versions equipped with Start&Stop  
system: at the end of the automatic  
braking, the Start&Stop system will  
activate as described in the "Start&Stop  
system" paragraph of the "Starting  
and driving" chapter.  
F1D0041  
54  
The system is only active if:  
the ignition key is at MAR;  
64  

Related Topics

Popular Owner Manuals