Doors and Locks for Your Ford Focus 4 Door Third generation(2010-2017)

Doors and Locks  
Opening a Rear Door From the Inside  
LOCKING AND UNLOCKING  
You can use the power door lock control  
or the remote control to lock and unlock  
your vehicle.  
Pull the interior door handle twice to  
unlock and open a rear door. The first pull  
unlocks the door and the second pull  
opens the door.  
Note: Always take your keys and lock all  
Remote Control  
doors when leaving your vehicle.  
You can use the remote control at any  
Power Door Locks  
time.  
The power door lock control is on the driver  
The liftgate or luggage compartment  
release button will only work when the  
vehicle speed is less than 4 mph (7 km/h).  
and front passenger door panels.  
A
Unlocking the Doors (Two-Stage  
Unlock)  
Press the button to unlock the  
driver door. Press the button  
again within three seconds to  
unlock all doors. The direction indicators  
will flash.  
B
Press and hold both the lock and unlock  
buttons on the remote control for three  
seconds to change between driver door or  
all doors unlock mode. The direction  
indicators will flash twice to indicate a  
change to the unlocking mode. Driver door  
mode only unlocks the driver door when  
you press the unlock button once. All door  
mode unlocks all doors when you press  
the unlock button once. The unlocking  
mode applies to the remote control,  
keyless entry keypad and intelligent  
access.  
E184784  
A
B
Unlock.  
Lock.  
Door Lock Indicator  
An LED on the power door lock control  
illuminates when you lock the door.  
They will remain illuminated for up to five  
minutes after you switch the ignition off.  
Locking the Doors  
Door Lock Switch Inhibitor  
Press the button to lock all  
When you electronically lock your vehicle,  
the power door lock switch will no longer  
operate after approximately 11 seconds.  
You must unlock your vehicle with the  
remote control or keyless keypad, or switch  
the ignition on, to restore function to these  
switches.  
doors. The direction indicators  
will flash. Press the button again  
within three seconds to confirm that all  
the doors are closed. The doors will lock  
again, the horn will sound and the direction  
indicators will flash if all the doors and the  
liftgate or luggage compartment are  
closed.  
59  
Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing  
 
Doors and Locks  
Mislock  
The system allows you to unlock, operate  
and lock your vehicle without using a key  
or remote control.  
If any door or the liftgate or luggage  
compartment is open, or if the hood is  
open on vehicles with an anti-theft alarm  
or remote start, the horn will sound twice  
and the direction indicators will not flash.  
Opening the Liftgate or Luggage  
Compartment  
Press twice within three seconds  
to unlatch the liftgate or luggage  
compartment.  
Make sure to close and latch the liftgate  
or luggage compartment before driving  
your vehicle. An unlatched liftgate or  
luggage compartment may cause objects  
to fall out or block your view.  
E78276  
You must have the intelligent access key  
within 5 ft (1.5 m) of your vehicle.  
Closing the Liftgate or Luggage  
Compartment  
Note: The system may not function if the  
intelligent access key is close to metal  
objects or electronic devices, for example  
keys or a cell phone.  
The liftgate or luggage compartment will  
not fully close if an intelligent access key  
is located inside the luggage compartment  
with the doors locked.  
Note: If a second intelligent access key is  
At a Door  
located within the liftgate or luggage  
Pull an exterior door handle to unlock and  
open the door. Do not touch the lock  
sensor on the front of the handle.  
compartment detection range, the liftgate  
or luggage compartment can be fully closed.  
Activating Intelligent Access (If  
Equipped)  
The system will not function if:  
Your vehicle battery has no charge.  
The intelligent access key battery has  
no charge.  
The intelligent access key frequencies  
are jammed.  
Note: If the system does not function, use  
the key blade to lock and unlock your  
vehicle. See Keys and Remote Controls  
(page 47).  
E185863  
60  
Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing  
Doors and Locks  
The locking sensors are on the front door  
If both front doors are closed, you can lock  
your vehicle by any method, regardless of  
whether the key is in the ignition or not.  
handles.  
Touch a locking sensor once to lock your  
vehicle and arm the alarm. There is a brief  
delay before you can unlock your vehicle  
again.  
Smart Unlocks for Intelligent  
Access Keys(If Equipped)  
This helps to prevent you from locking your  
key inside the passenger compartment or  
rear cargo area.  
Note: Keep the door handle clean to make  
sure the system operates correctly.  
Note: Your vehicle does not automatically  
lock. If you do not touch a locking sensor  
your vehicle will remain unlocked.  
When you electronically lock your vehicle  
with any door open, transmission in park  
(P) and the ignition off, the system will  
search for an intelligent access key in the  
passenger compartment after you close  
the last door. If the system finds a key, all  
of the doors will immediately unlock and  
the horn sounds twice, indicating that a  
key is inside.  
At the Liftgate or Luggage  
Compartment  
When you open one of the front doors and  
lock your vehicle using the power door lock  
control, all doors will lock then unlock if  
the ignition is on.  
E190028  
Disabled Intelligent Access Keys  
Press the release button above the license  
plate to unlatch the liftgate or luggage  
compartment.  
Intelligent access keys left inside your  
vehicle when locked are disabled.  
You cannot use a disabled intelligent  
access key to switch the ignition on.  
You will reactivate disabled intelligent  
access keys when you switch the ignition  
on using a valid key.  
Smart Unlocks for Integrated  
Keyhead Transmitter(If Equipped)  
This helps to prevent you from locking  
yourself out of your vehicle if the key is still  
in the ignition.  
When you open one of the front doors and  
lock your vehicle with the power door lock  
control, all the doors will lock then unlock  
and the horn will sound twice if the key is  
still in the ignition.  
You can still lock your vehicle with the key  
in the ignition. To do this, use the keyless  
entry keypad with the driver door closed,  
or press the lock button on the transmitter  
even if the doors are not closed.  
Autolock  
Autolock locks all the doors when all of the  
following occur:  
All doors are closed.  
The ignition is on.  
You shift into any gear putting your  
vehicle in motion.  
Your vehicle reaches a speed greater  
than 4 mph (7 km/h).  
61  
Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing  
Doors and Locks  
The lamps turn off if:  
Autounlock  
The ignition is on.  
Autounlock unlocks all the doors when all  
You press the remote control lock  
of the following occur:  
button.  
The ignition is on, all the doors are  
closed and your vehicle has been in  
motion at a speed greater than 4 mph  
(7 km/h).  
25 seconds have elapsed.  
The lamps will not turn off if:  
You switch them on with the lighting  
Your vehicle comes to a stop and you  
control.  
switch the ignition off or to accessory.  
Any door is open.  
You open the driver door within 10  
minutes of switching the ignition off or  
to accessory.  
Illuminated Exit  
For vehicles with an integrated keyhead  
transmitter, the interior lamps and select  
exterior lamps illuminate when you close  
all the doors, you switch the ignition off  
and you remove the key from the ignition.  
Note: If you electronically lock your vehicle  
after you switch the ignition off with the  
driver door closed, the doors will not  
autounlock.  
To enable or disable autounlock, do the  
The lamps turn off if all the doors remain  
following:  
closed and:  
1. Switch the ignition on.  
25 seconds have elapsed.  
2. Press the power door unlock control  
You insert the key in the ignition  
three times.  
(integrated keyhead transmitter only).  
3. Switch the ignition off.  
You press the START/STOP button  
(intelligent access key only).  
4. Press the power door unlock control  
three times.  
Battery Saver  
5. Switch the ignition on. The horn sounds  
indicating your vehicle is in  
If you leave the courtesy lamps, dome  
lamps or headlamps on, the battery saver  
will turn them off 10 minutes after you  
switch the ignition off.  
programming mode.  
6. Press the power door lock control and  
within five seconds, press the power  
door unlock control. The horn sounds  
once if disabled or twice if enabled.  
Accessory Mode Battery Saver for  
Intelligent Access Keys (If Equipped)  
7. Switch the ignition off. The horn sounds  
If you leave the ignition switched on and  
the engine is not running, the battery saver  
will turn the ignition off when it detects a  
certain amount of battery drain, or after  
45 minutes have elapsed.  
indicating programming is complete.  
Illuminated Entry  
The interior lamps and select exterior  
lamps illuminate when you unlock the  
doors with the remote entry system.  
62  
Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing  
Doors and Locks  
Opening the Liftgate or Luggage  
WARNINGS  
Compartment  
Make sure to close and latch the  
liftgate to prevent drawing exhaust  
fumes into your vehicle. This will also  
prevent passengers and cargo from falling  
out. If you must drive with the liftgate open,  
keep the vents or windows open so outside  
air comes into your vehicle. Failure to  
follow this warning could result in serious  
personal injury.  
With the Remote Control  
Press twice within three seconds  
to unlatch the liftgate or luggage  
compartment.  
From Inside Your Vehicle  
Press the button on the lighting  
control panel.  
Note: Be careful when opening or closing  
the liftgate in a garage or other enclosed  
area to avoid damaging the liftgate.  
Note: Do not hang anything, for example a  
bike rack, from the glass or liftgate. This  
could damage the liftgate and its  
components.  
From Outside Your Vehicle  
Note: Do not leave the liftgate open while  
driving. This could damage the liftgate and  
its components.  
Opening the Liftgate  
Manually  
E190028  
Press the release button above the license  
plate to unlatch the liftgate or luggage  
compartment. Your vehicle must be  
unlocked or have an intelligent access  
transmitter within 5 ft (1.5 m) of the liftgate  
or luggage compartment.  
MANUAL LIFTGATE  
E190028  
WARNINGS  
It is extremely dangerous to ride in a  
cargo area, inside or outside of a  
Press the release button above the license  
plate to unlatch the liftgate.  
vehicle. In a crash, people riding in  
these areas are more likely to be seriously  
injured or killed. Do not allow people to ride  
in any area of your vehicle that is not  
equipped with seats and seatbelts. Make  
sure everyone in your vehicle is in a seat  
and properly using a seatbelt. Failure to  
follow this warning could result in serious  
personal injury or death.  
With the Remote Control  
Press the button twice within  
three seconds.  
63  
Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing  
Doors and Locks  
Closing the Liftgate  
E155976  
A handle is located inside the liftgate to  
help with closing.  
E138637  
You can use the keypad to do the  
following:  
KEYLESS ENTRY(If Equipped)  
Lock or unlock the doors.  
Program and erase user codes.  
Arm and disarm the anti-theft alarm.  
SECURICODEKEYLESS ENTRY  
KEYPAD  
The keypad is located near the driver  
window. It is invisible until touched and  
then it lights up so you can see and touch  
the appropriate buttons.  
Note: If you enter your entry code too fast  
on the keypad, the unlock function may not  
work. Enter your entry code again more  
slowly.  
You can operate the keypad with the  
factory-set five-digit entry code. The code  
is on the owners wallet card in the glove  
box and is available from an authorized  
dealer. You can also program up to five of  
your own five-digit personal entry codes.  
Programming a Personal Entry Code  
1. Enter the factory-set five-digit code.  
2. Press 1·2 on the keypad within five  
seconds.  
3. Enter your personal five-digit code. You  
must enter each number within five  
seconds of each other.  
4. Press 1·2 on the keypad to save  
personal code 1.  
The doors lock then unlock to confirm that  
programming was successful.  
64  
Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing  
Doors and Locks  
To program additional personal entry  
codes, repeat Steps 1-3, then for Step 4:  
Locking and Unlocking the Doors  
Locking All Doors  
Press and hold 7·8 and 9·0 on the keypad  
simultaneously with the driver door closed.  
You do not need to enter a code first.  
Press 3·4 to save personal code 2.  
Press 5·6 to save personal code 3.  
Press 7·8 to save personal code 4.  
Press 9·0 to save personal code 5.  
Unlocking All Doors  
Enter the factory-set code or your personal  
code, then press 3·4 on the keypad within  
five seconds.  
Hints:  
Do not set a code that uses five of the  
same number.  
Do not use five numbers in sequential  
order.  
Unlocking Only the Driver Door  
The factory-set code works even if you  
have set your own personal code.  
Enter the factory-set or your personal  
five-digit code. You must press each  
number within five seconds of each other.  
The interior lamps illuminate.  
Note: All doors unlock if the two-stage  
unlocking feature is turned off. See Locking  
and Unlocking (page 59).  
Erasing a Personal Code  
1. Enter the factory-set five-digit code.  
2. Press and release 1·2 on the keypad  
within five seconds.  
3. Press and hold 1·2 for two seconds.  
You must do this within five seconds  
of completing step 2.  
DOOR  
All personal codes erase and only the  
factory-set five-digit code works.  
WARNINGS  
Anti-Scan Feature  
Keep vehicle doors and luggage  
compartment locked and keep keys  
and remote transmitters out of a  
childs reach. Unsupervised children could  
lock themselves in the trunk and risk injury.  
Children should be taught not to play in  
vehicles.  
The keypad goes into an anti-scan mode  
if you enter the wrong code seven times.  
This mode turns off the keypad for one  
minute and the keypad lamp flashes.  
The anti-scan feature turns off after any  
of the following occur:  
One minute of keypad inactivity.  
Do not leave children or animals  
unattended in the vehicle. On hot  
You press the unlock button on the  
days, the temperature in the trunk or  
vehicle interior can rise very quickly.  
Exposure of people or animals to these  
high temperatures for even a short time  
can cause death or serious heat-related  
injuries, including brain damage. Small  
children are particularly at risk.  
remote control.  
You switch your vehicle on.  
You unlock the vehicle using intelligent  
access.  
65  
Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing  
Doors and Locks  
Your vehicle is equipped with a release  
handle that provides a means of escape  
for children and adults if they become  
locked inside the luggage compartment.  
Adults should familiarize themselves with  
the operation and location of the release  
handle.  
E144403  
The handle is located inside the luggage  
compartment either on the luggage  
compartment door (lid) or near the tail  
lamps. It is composed of a material that  
will glow for hours in darkness following  
brief exposure to ambient light.  
Pull the handle and push up on the luggage  
compartment door (lid) to open from  
within the luggage compartment.  
66  
Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing