Get Locks and Security Guide for Ford Fusion 4 Door First Generation (2006-2012)

Locks and Security

KEYS

Your vehicle is equipped with two

Integrated Keyhead Transmitters

(IKTs). The key blade functions as a

programmed key which starts the

vehicle and unlocks/locks all the

doors. The transmitter portion

functions as the remote entry

transmitter.

Your IKTs are programmed to your vehicle; using a non-programmed key

will not permit your vehicle to start. If you lose your authorized dealer

supplied IKTs, replacement IKTs are available through your authorized

dealer. Standard SecuriLock௡ keys without remote entry transmitter

functionality can also be purchased from your authorized dealer if

desired.

Always carry a spare key with you in case of an emergency.

For more information regarding programming replacement IKTs, refer to

the SecuriLock௡ passive anti-theft system section later in this chapter.

Note: Your vehicle’s IKTs were

issued with a security label that

provides important vehicle key cut

information. It is recommended that

you keep the label in a safe place

for future reference.

95

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

MYKEYா

The MyKey௡ feature allows you to program a restricted driving mode to

promote good driving habits. All but one of the keys programmed to the

vehicle can be activated as a MyKey௡. The key will remain restricted

until MyKey௡ is cleared. Any remaining keys are referred to as an

“administrator key” or admin key. The admin key can be used to create a

MyKey௡, program optional MyKey௡ settings, and clear the MyKey௡

feature. When the MyKey௡ feature is enabled the user can use system

check in the message center to see how many MyKeys௡ and admin keys

are programmed to the vehicle, and see the total distance the vehicle has

been driven with the MyKey௡ active.

MyKey௡ restricted features

Standard settings – these settings cannot be changed

• Belt-Minder cannot be disabled. The audio system will be muted

whenever Belt-Minder௡ is activated until the safety belts are buckled.

Refer to the Seating and Safety Restraints chapter for a detailed

description of Belt-Minder௡ operation.

• Low fuel warnings are displayed in the message center followed by a

chime when the distance to empty value reaches 75 miles (120 km).

• The following systems, if equipped, cannot be turned off: reverse

sensing system, blind spot information system (BLIS௡) with cross

traffic alert and collision warning system.

Optional settings – these settings can be changed

• Vehicle speed is limited to 80 mph (130 km/h). Visual warnings are

displayed followed by a chime when the vehicle speed has reached

80 mph (130 km/h).

• Visual warnings are displayed followed by a chime when a preselected

vehicle speed of 45, 55 or 65 mph (75, 90, or 105 km/h) is exceeded.

• The maximum volume of the audio system is limited to 45%. MYKEY

VOLUME LIMITED will be displayed in the audio system display when

attempting to exceed the limited volume.

• The AdvanceTrac௡ system cannot be turned off. When this optional

setting is on, the MyKey௡ user will not be able to deactivate the

system. Note: It may be beneficial to deactivate the AdvanceTrac௡

system if the vehicle is stuck in snow, mud or sand.

96

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Create a MyKey௡

To program MyKey௡ on one of the keys programmed to the vehicle,

insert the key that you want to make a MyKey௡ into the ignition. Turn

the ignition on. Use the message center buttons to do the following:

1. Press SETUP until PRESS RESET TO CREATE MYKEY is displayed.

2. Press and release the RESET button. HOLD RESET TO CONFIRM

MYKEY will be displayed.

3. Press and hold the RESET button for two seconds until MARK THIS

AS RESTRICTED is displayed.

4. Wait until KEY RESTRICTED AT NEXT START is displayed.

MyKey௡ is successfully programmed. Make sure you label it so you can

distinguish it from the admin keys. Note: To program the optional

settings go to Step 2 in the Programming MyKey௡ Optional Settings

section. If your vehicle is equipped with remote start, see the Using

MyKey௡ with Remote Start Systems section.

Note: The MyKey௡ can be cleared within the same key cycle that it was

created, otherwise a standard key (administrator key) is required to

clear the MyKey௡ programming. To clear all MyKeys௡ go to Step 2 in the

Clear MyKey௡ section.

Programming MyKey௡ Optional Settings

Turn the ignition on using an admin key. To program the optional

settings, use the message center buttons to do the following:

1. Press SETUP until RESET FOR MYKEY SETTINGS is displayed.

2. Press and release the RESET button to display MyKey setup menus.

The first menu shown is:

MYKEY MAX MPH <80 MPH> OFF

3. If you don’t want to change the maximum speed setting, press the

SETUP button to display the next menu. The remaining menus appear as

follows with the default settings shown:

MYKEY MPH TONES 45 55 65 <OFF>

MYKEY VOLUME LIMIT <ON> OFF

MYKEY ADVTRAC CTRL ON <OFF>.

4. On any of the menus press RESET to highlight your choice with the

<…>.

5. Press SETUP to enter your choice. The next optional setting will be

displayed.

6. Repeat Steps 4 and 5 until you are done changing the optional

settings.

97

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Clear MyKey௡

To reset all MyKeys௡ as admin keys, do the following:

1. Turn the vehicle on using the admin key.

2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed.

3. Press and release the RESET button. HOLD RESET TO CONFIRM

CLEAR is displayed.

4. Press and hold the RESET button for two seconds until ALL MYKEYS

CLEARED is displayed.

Check MyKey௡ system status

The vehicle system check will provide the status of the following MyKey௡

parameters:

• MYKEY MILES — This odometer only tracks mileage when a MyKey௡

is used. If mileage does not accumulate as expected, then the MyKey௡

is not being used by the intended user. The only way to reset this

odometer to zero is by clearing MyKey௡. If this odometer is lower than

the last time you checked, then the MyKey௡ system has been recently

cleared.

• # MYKEY(S) PROGRAMMED — Indicates how many MyKeys௡ are

programmed to the vehicle. Can be used to detect deletion of a

MyKey௡.

• # ADMIN KEYS PROGRAMMED — Indicates how many admin keys

are programmed to the vehicle. Can be used to detect if an additional

spare key has been programmed to the vehicle.

Refer to Message center in the Instrument Cluster chapter for MyKey௡

system warnings displays.

Using MyKey௡ with remote start systems

MyKey௡ is not compatible with non-Ford approved aftermarket remote

start systems. If you choose to install a remote start system please see

your authorized dealer for a Ford approved remote start system.

When using a Ford-approved remote start system, the default settings

will recognize the remote start system as an additional admin key with

its associated privileges. Program the remote start system as a MyKey௡

in addition to the key that they have already programmed as a MyKey௡.

To program the remote start system as MyKey௡, do the following:

1. Enter the vehicle and close all doors.

2. Remote start the vehicle using a remote start fob.

3. Follow Steps 1-4 in the Create a MyKey௡ section.

98

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED or

ADMIN KEYS PROGRAMMED that is displayed in the MyKey௡ system

status menus will include the remote start system as an additional key in

the total count. See the Check MyKey௡ system status section.

Note: For all vehicles with remote start installed, it is possible to

program all ’real’ keys as MyKeys௡, in which case, you will need to use

your remote start system to reset all MyKeys௡ as admin keys by doing

the following:

1. Enter the vehicle, close all doors.

2. Remote start the vehicle using your remote start fob.

3. Follow Steps 1-4 in the Clear MyKey௡ section.

Troubleshooting

Condition

Potential Causes

Can’t create a MyKey௡

• Key in the ignition is already a

MyKey௡.

• Key in the ignition is the last

remaining admin key (there always

has to be at least one admin key).

•SecuriLock௡ Passive Anti-Theft

System is disabled or in unlimited

mode

• Vehicle has been started using a

remote start system that is

programmed as MyKey௡. Refer to

Using MyKey௡ with remote start

systems section.

Cannot program the MyKey௡

optional settings

• Key in the ignition is a MyKey௡

• No MyKeys௡ are programmed to the

vehicle. Refer to Create a MyKey௡

section

• Vehicle has been started using a

remote start system that is

programmed as a MyKey௡. Refer to

Using MyKey௡ with remote start

systems section.

99

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Condition

Potential Causes

Cannot clear MyKey௡

• Key in the ignition is a MyKey௡

• No MyKeys௡ are programmed to the

vehicle. Refer to Create a MyKey௡

section

• Vehicle has been started using a

remote start system that is

programmed as a MyKey௡. Refer to

MyKey௡ with remote start systems

section.

Lost the only admin key

Lost any key

• Purchase a new key from your

authorized dealer

• For programming spare keys, refer

to the Programming spare keys

section in this chapter.

I accidentally programmed all

keys as MyKeys௡

• Vehicle has a remote start system

that is recognized as an admin key.

Refer to the Using MyKey௡ with

remote start systems section to reset

all MyKeys௡ as admin keys.

MyKey௡ programmed total

includes one additional key

• Unknown key has been programmed

to the vehicle as a MyKey௡.

• Vehicle is equipped with a remote

start system. Refer to Using MyKey௡

with remote start systems section.

Admin keys programmed total • Unknown key has been programmed

includes one additional key

to the vehicle as admin key.

• Vehicle is equipped with a remote

start system. Refer to Using MyKey௡

with remote start systems section.

• MyKey௡ is not being used by the

intended user.

MyKey௡ miles do not

accumulate

• MyKey௡ system has been recently

cleared.

100

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

POWER DOOR LOCKS

• Press the

control to unlock all

doors.

• Press the

control to lock all

doors.

Smart locks

This feature attempts to help prevent you from locking yourself out of

the vehicle if your key is still in the ignition.

When you open one of the front doors and you lock the vehicle with the

power door lock control (on the driver or passenger door trim panel), all

the doors will lock, then all doors will automatically unlock reminding

you that your key is still in the ignition.

The vehicle can still be locked, with the key in the ignition, using the

manual lock control on the door, locking the driver’s door with a key, or

using the lock control on the remote entry transmitter portion of your

Integrated Keyhead Transmitter.

If both front doors are closed, the vehicle can be locked from any

method, regardless of whether the key is in the ignition or not.

Autolock feature

The autolock feature will lock all the doors when:

• all the doors are closed,

• the ignition is in the on position,

• you shift into any gear putting the vehicle in motion, and

• the vehicle attains a speed greater than 12 mph (20 km/h).

The autolock feature repeats when:

• any door is opened then closed while the ignition is in the on position

and the vehicle speed is 9 mph (15 km/h) or lower, and

• the vehicle then attains a speed greater than 12 mph (20 km/h).

101

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Deactivating/activating autolock feature

Your vehicle comes with the autolock features activated; there are four

methods to enable/disable this feature:

• Through your authorized dealer,

• by using a power door unlock/lock sequence, or

• by using the keyless entry pad (if equipped).

• by using the instrument cluster message center. Refer to Message

center in the Instrument Cluster chapter.

Note: The autolock feature can be activated/deactivated independently

of the autounlock feature.

Before starting, ensure the ignition is in the off position and all vehicle

doors are closed. You must complete Steps 1–5 within 30 seconds or the

procedure will have to be repeated. If the procedure needs to be

repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and

turn the ignition to the on position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the on

position to the off position.

4. Press the power door unlock control on the door panel three times.

5. Turn the ignition back to the on position. The horn will chirp one time

to confirm programming mode has been entered and is active.

6. To enable/disable the autolock feature, press the unlock control, then

press the lock control. The horn will chirp once if autolock was

deactivated or twice (one short and one long chirp) if autolock was

activated.

7. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

Keyless entry keypad procedure

1. Turn the ignition to the 1 off

position.

2. Close all the doors.

3. Enter factory–set 5–digit entry

code.

102

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8.

5. Release the 7 • 8.

6. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been

enabled.

Autounlock feature

The autounlock feature will unlock all the doors when:

• the ignition is in the on position, all the doors are closed, and the

vehicle has been in motion at a speed greater than 12 mph (20 km/h);

• the vehicle has then come to a stop and the ignition is turned to the

off or accessory position; and

• the driver door is opened within 10 minutes of the ignition being

transitioned to the off or accessory position.

Note: The doors will not autounlock if the vehicle has been

electronically locked before the driver door is opened.

Deactivating/activating autounlock feature

Your vehicle comes with the autounlock features activated; there are four

methods to enable/disable this feature:

• Through your authorized dealer,

• by using a power door unlock/lock sequence, or

• by using the keyless entry keypad (if equipped) or

• by using the instrument cluster message center. Refer to Message

center in the Instrument Cluster chapter.

Note: The autounlock feature can be activated/deactivated

independently of the autolock feature.

Before starting, ensure the ignition is in the off position and all vehicle

doors are closed. You must complete Steps 1–5 within 30 seconds or the

procedure will have to be repeated. If the procedure needs to be

repeated, wait a minimum of 30 seconds before beginning again.

103

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

1. Place the key in the ignition and

turn the ignition to the on position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the on

position to the off position.

4. Press the power door unlock control on the door panel three times.

5. Turn the ignition back to the on position. The horn will chirp one time

to confirm programming mode has been entered and is active.

6. To enable/disable the autounlock feature, press the lock control, then

press the unlock control. The horn will chirp once if autounlock was

deactivated or twice (one short and one long chirp) if autounlock was

activated.

7. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

Keyless entry keypad procedure

1. Turn the ignition to the 1 off

position.

2. Close all the doors.

3. Enter factory–set 5–digit entry

code.

4. Press and hold the 3 • 4. While holding the 3 • 4, press and release

the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8 a

second time.

5. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been

enabled.

104

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

CHILDPROOF DOOR LOCKS

• When these locks are set, the

rear doors cannot be opened from

the inside.

• The rear doors can be opened

from the outside when the

childproof door locks are set, but

the doors are unlocked.

The childproof locks are located on

the rear edge of each rear door and

must be set separately for each

door. Setting the lock for one door will not automatically set the lock for

both doors.

• Insert the key and turn to the lock position (key at an angle) to

engage the childproof lock.

• Insert the key and turn to the unlock position (key horizontal) to

disengage the childproof lock.

INTERIOR LUGGAGE COMPARTMENT RELEASE

Your vehicle is equipped with a mechanical interior luggage compartment

release handle that provides a means of escape for children and adults in

the event they become locked inside the luggage compartment.

Adults are advised to familiarize themselves with the operation and

location of the release handle.

105

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

To open the luggage compartment

door (lid) from within the luggage

compartment, pull the illuminated

“T” shaped handle and push up on

the trunk lid. The handle is

composed of a material that will

glow for hours in darkness following

brief exposure to ambient light.

The “T” shaped handle will be

located either on the luggage

compartment door (lid) or inside

the luggage compartment near the

tail lamps.

WARNING: Keep vehicle

doors and luggage

compartment locked and keep

keys and remote transmitters out

of a child’s reach. Unsupervised

children could lock themselves in

the trunk and risk injury. Children

should be taught not to play in

vehicles.

WARNING: Do not leave children, unreliable adults, or animals

unattended in the vehicle. On hot days, the temperature in the

trunk or vehicle interior can rise very quickly. Exposure of people or

animals to these high temperatures for even a short time can cause

death or serious heat-related injuries, including brain damage. Small

children are particularly at risk.

106

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

REMOTE ENTRY SYSTEM

The Integrated Keyhead Transmitter (IKT) complies with part 15 of the

FCC rules and with RSS-210 of Industry Canada. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

The typical operating range for your IKT is approximately 33 feet

(10 meters). A decrease in operating range could be caused by:

• weather conditions,

• nearby radio towers,

• structures around the vehicle, or

• other vehicles parked next to your vehicle.

The IKT allows you to:

• remotely unlock the vehicle

doors.

• remotely lock all the vehicle

doors.

• remotely open the trunk.

• activate the personal alarm.

• arm and disarm the perimeter

anti-theft system.

• operate the illuminated entry

feature.

The remote entry lock/unlock feature operates in any ignition position

except while the key is held in the start position. The panic feature

operates with the key in the off position.

If there are problems with the remote entry system, make sure to take

ALL Integrated Keyhead Transmitters with you to the authorized

dealer in order to aid in troubleshooting the problem.

Unlocking the doors/two-stage unlock

1. Press

and release to unlock the driver’s door. Note: The interior

lamps will illuminate.

107

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

2. Press

and release again within five seconds to unlock all the doors.

The remote entry system activates the illuminated entry feature; this

feature turns on the lamps for 25 seconds or until the ignition is turned

to the on position.

The battery saver feature will turn off the lamps 30 minutes after the

ignition is turned to the off position.

Two-stage unlocking may be disabled or re-enabled by simultaneously

pressing the

and

controls on the IKT for four seconds (disabling

two-stage unlock allows all vehicle doors to unlock simultaneously). The

turn lamps will illuminate twice to indicate that two-stage unlock was

enabled or disabled.

Opening front windows and moon roof (if equipped)

You can open the vehicle’s windows, and (if equipped) vent the moon

roof by using the

control on the transmitter. Refer to Power

windows in the Driver Controls chapter for more information.

Locking the doors

1. Press

and release to lock all the doors. The turn lamps will flash.

2. Press

and release again within three seconds to confirm that all

the doors are closed. Note: The doors will lock again, the horn will chirp

and the turn lamps will illuminate once if all the doors and trunk are

closed.

Note: If any door or the trunk is not closed, or if the hood is not closed

in vehicles equipped with the perimeter alarm feature, the horn will

chirp twice and the lamps will not illuminate.

Car finder

Press

twice within three seconds. The horn will chirp and the turn

lamps will flash. It is recommended that this method be used to locate

your vehicle, rather than using the panic alarm.

Sounding a panic alarm

Press

to activate the alarm. The horn will sound and the turn lamps

will flash for a maximum of three minutes. Press again or turn the

ignition to the on position to deactivate, or wait for the alarm to time out

in three minutes.

Note: The panic alarm will only operate when the ignition is in the off

position.

108

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Opening the trunk

Press twice within three seconds to open the trunk.

• Ensure that the trunk is closed and latched before driving your

vehicle. Failure to properly latch the trunk may cause objects to fall

out or block the driver’s rear view.

Replacing the battery

The integrated keyhead transmitter uses one coin type three-volt lithium

battery CR2032 or equivalent.

To replace the battery:

1. Twist a thin coin in the slot of the

IKT near the key ring in order to

remove the battery cover.

Note: Do not wipe off any grease on

the battery terminals on the back

surface of the circuit board.

2. Remove the old battery.

Note: Please refer to local

regulations when disposing of

transmitter batteries.

3. Insert the new battery. Refer to

the instructions inside the IKT for

the correct orientation of the

battery. Press the battery down to

ensure that the battery is fully

seated in the battery housing cavity.

4. Snap the battery cover back onto

the key.

Note: Replacement of the battery will not cause the IKT to become

deprogrammed from your vehicle. The IKT should operate normally after

battery replacement.

Replacing lost integrated keyhead transmitters (IKTs)

If you would like to have your integrated keyhead transmitters

reprogrammed because you lost one, or would like to buy additional

IKTs, you can either reprogram them yourself, or take all IKTs to your

authorized dealer for reprogramming.

109

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

How to reprogram your integrated keyhead transmitters (IKTs)

To program a new integrated keyhead transmitter yourself, refer to

Programming spare keys in the SecuriLock௡ passive anti-theft system

section of this chapter. Note: At least two IKTs are required to perform

this procedure yourself.

Illuminated entry

The interior lamps and puddle lamps (if equipped) illuminate when the

Integrated Keyhead Transmitter is used to unlock the door(s).

The illuminated entry system will turn off the lights if:

• the ignition is turned to the on position,

• the Integrated Keyhead Transmitter lock control is pressed,

• The vehicle is locked using the keyless entry keypad (if equipped), or

• after 25 seconds of illumination.

The lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

Perimeter lamps illuminated entry

With the Integrated Keyhead Transmitter system, the following items will

illuminate when the

• Parking lamps

• Tail lamps

control on the transmitter is pressed:

• Headlamps

The lamps will automatically turn off:

• if the ignition switch is turned to the 3 (on) position,

• The vehicle is locked using the keyless entry keypad (if equipped), or

• after 25 seconds of illumination.

Note: On some vehicles, the perimeter lamps illuminated entry feature

will not activate in daylight conditions.

Deactivating/activating perimeter lamps illuminated entry

You may enable/disable this feature by having your vehicle serviced by

your authorized dealer.

You may also perform the following power door lock sequence to

enable/disable the perimeter lamps feature. Note: Before starting, ensure

110

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

the ignition is in the 1 (off) position and all vehicle doors are closed. You

must complete Steps 1–5 within 30 seconds or the procedure will have

to be repeated. If the procedure needs to be repeated, wait a minimum

of 30 seconds before beginning again.

1. Place the key in the ignition and

turn the ignition to the 3 (on)

position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the 3 (on)

position to the 1 (off) position.

4. Press the power door unlock control on the door panel three times.

5. Turn the ignition back to the 3 (on) position. The horn will chirp one

time to confirm programming mode has been entered and is active.

6. Press the power door unlock control twice within five seconds.

Note: The horn will chirp once to indicate the perimeter lighting feature

has been deactivated. The horn will chirp once and honk once (one short

and one long) to indicate the perimeter lighting feature has been

activated.

7. Turn the ignition to the 1 (off) position to exit the procedure.

Note: The horn will chirp once to confirm the procedure is complete.

Illuminated exit

• When all vehicle doors are closed and the key is removed from the

ignition, the interior lamps and the puddle lamps (if equipped) will

illuminate.

The lamps will turn off if all the doors remain closed and

• 25 seconds elapse, or

• the key is inserted in the ignition.

Battery saver

The battery saver will shut off the lamps 30 minutes after the ignition

has been turned to the 1 (off) position.

• If the dome lamps were turned on using the panel dimmer control, the

battery saver will shut them off 30 minutes after the ignition has been

turned to the off position.

• If the courtesy lamps were turned on because one of the vehicle doors

or the trunk was opened, the battery saver will shut off them off

10 minutes after the ignition has been turned to the off position.

111

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

• The battery saver will shut off the headlamps 10 minutes after the

ignition has been turned to the off position.

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)

You can use the keyless entry

keypad to:

• lock or unlock the doors without

using a key.

• open the trunk.

The keypad can be operated with the factory set 5–digit entry code; this

code is located on the owner’s wallet card in the glove box and is

available from your authorized dealer. You can also create up to three of

your own 5–digit personal entry codes.

When pressing the controls on the keypad, press the middle of the

controls to ensure a good activation.

Programming a personal entry code

To create your own personal entry code:

1. Enter the factory set code.

2. Within five seconds press the 1 • 2 on the keypad.

3. Enter your personal 5-digit code. Each number must be entered

within five seconds of each other.

4. The doors will lock then unlock to confirm that your personal keycode

has been programmed to the module.

Tips:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

• The factory set code will work even if you have set your own personal

code.

Erasing personal code

1. Enter the factory set 5–digit code.

2. Within five seconds, press the 1 • 2 on the keypad and release.

3. Press and hold the 1 • 2 for two seconds. This must be done within

five seconds of completing Step 2.

All personal codes are now erased and only the factory set 5–digit code

will work.

112

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Anti-scan feature

If the wrong code has been entered seven times (35 consecutive button

presses), the keypad will go into an anti-scan mode. This mode disables

the keypad for one minute and the keypad lamp will flash.

The anti-scan feature will turn off after:

• one minute of keypad inactivity.

• pressing the

control on the remote entry transmitter portion of

your integrated keyhead transmitter.

• the ignition is turned on.

Unlocking and locking the doors using keyless entry

To unlock the driver’s door, enter the factory set 5-digit code or your

personal code. Each number must be pressed within five seconds of each

other. The interior lamps will illuminate. Note: If the two-stage unlocking

feature is disabled, all doors will unlock; for more information regarding

two-stage unlocking, refer to the Unlocking the doors/Two stage unlock

section earlier in this chapter.

To unlock all doors, enter the factory set code or your personal code,

then press the 3 • 4 control within five seconds.

To open the trunk, enter the factory set code or your personal code,

then press the 5 • 6 control within five seconds.

To lock all doors, press and hold the 7 • 8 and the 9 • 0 at the same

time (with the driver’s door closed). You do not need to enter the

keypad code first.

SECURILOCKா PASSIVE ANTI-THEFT SYSTEM

SecuriLock௡ passive anti-theft system is an engine immobilization

system. This system is designed to help prevent the engine from being

started unless a coded integrated keyhead transmitter (IKT)

programmed to your vehicle is used. The use of the wrong type of

coded key may lead to a “no-start” condition.

Your vehicle comes with two coded integrated keyhead transmitters;

additional coded IKTs may be purchased from your authorized dealer.

Standard SecuriLock௡ keys without remote entry transmitter

functionality can also be purchased from your authorized dealer if

desired. The authorized dealer can program your spare IKTs to your

vehicle or you can program the IKTs yourself. Refer to Programming

spare keys for instructions on how to program the coded key.

Note: The SecuriLock௡ passive anti-theft system is not compatible with

non-Ford aftermarket remote start systems. Use of these systems may

result in vehicle starting problems and a loss of security protection.

113

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Note: Large metallic objects, electronic devices that are used to

purchase gasoline or similar items, or a second coded key on the same

key chain may cause vehicle starting issues. You need to prevent these

objects from touching the coded IKT while starting the engine. These

objects will not cause damage to the coded IKT, but may cause a

momentary issue if they are too close to the IKT when starting the

engine. If a problem occurs, turn the ignition off, remove all objects on

the key chain away from the coded IKT and restart the engine.

Note: Do not leave a duplicate coded key in the vehicle. Always

take your keys and lock all doors when leaving the vehicle.

Anti-theft indicator

The anti-theft indicator is located in the instrument panel cluster.

• When the ignition is in the off

position, the indicator will flash

once every two seconds to

indicate the SecuriLock௡ system

is functioning as a theft

deterrent.

• When the ignition is in the on position, the indicator will glow for

three seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock௡ system, the indicator will flash

rapidly or glow steadily when the ignition is in the on position. If this

occurs, turn the ignition off then back to on to make sure there was no

electronic interference with the programmed key. If the vehicle doesn’t

start, try to start it with the 2nd programmed key and if successful

contact your authorized dealership for key replacement. If the indicator

still flashes rapidly or glows steadily, the vehicle will not start, contact

your authorized dealer as soon as possible for service.

Automatic arming

The vehicle is armed immediately after switching the ignition to the off

position.

The theft indicator will flash every

two seconds to act as a theft

deterrent when the vehicle is

armed.

Automatic disarming

The vehicle is disarmed immediately after the ignition is turned to the on

position.

114

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

The theft indicator will illuminate for three seconds and then go out. If

the theft indicator stays on for an extended period of time or flashes

rapidly, contact your authorized dealer as soon as possible.

Replacement of integrated keyhead transmitters (IKT) and coded

keys

Note: Your vehicle comes equipped with two integrated keyhead

transmitters (IKTs). The IKT functions as both a programmed ignition

key that operates all the locks and starts the vehicle, as well as a remote

keyless entry transmitter. A maximum of eight coded keys can be

programmed to your vehicle; only four of these eight keys can be IKTs

with remote entry functionality.

If your IKTs or standard SecuriLock௡ coded keys are lost or stolen and

you don’t have an extra coded key, you will need to have your vehicle

towed to an authorized dealer. The key codes need to be erased from

your vehicle and new coded keys will need to be programmed.

Replacing coded keys can be very costly. Store an extra programmed key

away from the vehicle in a safe place to help prevent any

inconveniences. Please visit an authorized dealer to purchase additional

spare or replacement keys.

Programming spare keys

You can program your own integrated keyhead transmitters or standard

SecuriLock௡ coded keys to your vehicle. This procedure will program

both the engine immobilizer key code and the remote entry transmitter

portion of the IKT to your vehicle. Note: A maximum of eight coded

keys can be programmed to your vehicle; only four of these eight can be

IKTs with remote entry functionality.

Tips:

• Only use integrated keyhead transmitters (IKTs) or standard

SecuriLock௡ keys.

• You must have two previously programmed coded keys (keys that

already operate your vehicle’s engine) and the new unprogrammed

key(s) readily accessible.

• If two previously programmed coded keys are not available, you must

take your vehicle to your authorized dealer to have the spare key(s)

programmed.

115

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Please read and understand the

entire procedure before you begin.

1. Insert the first previously

programmed coded key into the

ignition.

2. Turn the ignition from the 1 (off)

position to the 3 (on) position. Keep

the ignition in the 3 (on) position

for at least three seconds, but no more than 10 seconds.

3. Turn the ignition to the 1 (off) position and remove the first coded

key from the ignition.

4. After three seconds but within 10 seconds of turning the ignition to

the 1 (off) position, insert the second previously coded key into the

ignition.

5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep

the ignition in the 3 (on) position for at least three seconds, but no more

than 10 seconds.

6. Turn the ignition to the 1 (off) position and remove the second

previously programmed coded key from the ignition.

7. After three seconds but within 20 seconds of turning the ignition to

the 1 (off) position and removing the previously programmed coded

key, insert the new unprogrammed key (new key/valet key) into the

ignition.

8. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep

the ignition in the 3 (on) position for at least six seconds.

9. Remove the newly programmed coded key from the ignition.

If the key has been successfully programmed it will start the vehicle’s

engine and will operate the remote entry system (if the new key is an

integrated keyhead transmitter). The theft indicator light will illuminate

for three seconds and then go out to indicate successful programming.

If the key was not successfully programmed, it will not start your

vehicle’s engine and/or will not operate the remote entry features. The

theft indicator light may flash on and off. Wait 20 seconds and you may

repeat Steps 1 through 8. If failure repeats, bring your vehicle to your

authorized dealer to have the new key(s) programmed.

To program additional new unprogrammed key(s), wait 20 seconds and

then repeat this procedure from Step 1.

116

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

PERIMETER ALARM SYSTEM

The perimeter anti-theft system will help protect your vehicle from

unauthorized entry.

If there is any potential perimeter anti-theft problem with your vehicle,

ensure ALL integrated keyhead transmitters are brought to the

authorized dealer to aid in troubleshooting.

Arming the system

When armed, this system will respond if unauthorized entry is

attempted. When unauthorized entry occurs, the system will flash the

turn signal lamps and will sound the horn.

The system is ready to arm whenever the key is in the 1 (off) position,

or is removed from the ignition. Either of the following actions will

prearm the alarm system:

• Press the

control on the remote entry transmitter portion of your

Integrated Keyhead Transmitter.

When you press the lock control twice within three seconds on the

remote entry transmitter portion of your IKT, the horn will chirp once to

let you know that all doors, the hood and the trunk are closed. If any of

these are not closed, the horn will chirp twice to warn you that a door,

the hood or the trunk is still open.

• Press the driver or passenger

interior door lock control while

the door is open, then close the

door.

• Press the 7 • 8 and the 9 • 0

controls on the keyless entry

keypad (if equipped) at the same

time to lock the doors (driver’s

door must be closed).

There is a 20 second countdown when any of the above actions occur

before the vehicle becomes armed.

Each door, the hood or the trunk is armed individually, and if any are

open, they must be closed for the system to enter the 20 second

countdown.

The turn signal lamps will flash once when all doors, the hood and the

trunk are closed indicating the vehicle is locked and entering the

20 second countdown.

117

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Disarming the system

You can disarm the system by any of the following actions:

• Unlock the doors by using the remote entry transmitter portion of

your Integrated Keyhead Transmitter.

• Unlocking the doors using the keyless entry keypad (if equipped).

• Turn ignition to the on position with a valid SecuriLock™ key.

• Press the panic control on the remote entry transmitter portion of

your IKT. This will only shut off the horn and turn lamps when the

alarm is sounding. The alarm system will still be armed.

If using a key in the driver’s door to unlock the vehicle, a chime will

sound and the message center will display TO STOP ALARM START

VEHICLE when you open the door and you will have 12 seconds to

disarm the alarm system using any of the actions above, otherwise the

alarm will trigger.

Pressing the power door unlock control within the 20 second prearmed

mode will return the vehicle to a disarmed state.

Triggering the anti-theft system

The armed system will be triggered if:

• Any door, the hood or the trunk is opened without using the door key

or the remote entry transmitter portion of your IKT.

• The ignition is turned to the 3 (on) position with an invalid

SecuriLock௡ key.

118

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security for Your Ford Fusion 4 Door First Generation (2006-2012)

Related Topics

Popular Owner Manuals

Latest Owner Manuals