Get Locks and Security -> Locks Guide for Ford Fusion 4 Door First Generation (2006-2012)

Locks and Security

POWER DOOR LOCKS

• Press the

control to unlock all

doors.

• Press the

control to lock all

doors.

Smart locks

This feature attempts to help prevent you from locking yourself out of

the vehicle if your key is still in the ignition.

When you open one of the front doors and you lock the vehicle with the

power door lock control (on the driver or passenger door trim panel), all

the doors will lock, then all doors will automatically unlock reminding

you that your key is still in the ignition.

The vehicle can still be locked, with the key in the ignition, using the

manual lock control on the door, locking the driver’s door with a key, or

using the lock control on the remote entry transmitter portion of your

Integrated Keyhead Transmitter.

If both front doors are closed, the vehicle can be locked from any

method, regardless of whether the key is in the ignition or not.

Autolock feature

The autolock feature will lock all the doors when:

• all the doors are closed,

• the ignition is in the on position,

• you shift into any gear putting the vehicle in motion, and

• the vehicle attains a speed greater than 12 mph (20 km/h).

The autolock feature repeats when:

• any door is opened then closed while the ignition is in the on position

and the vehicle speed is 9 mph (15 km/h) or lower, and

• the vehicle then attains a speed greater than 12 mph (20 km/h).

101

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Deactivating/activating autolock feature

Your vehicle comes with the autolock features activated; there are four

methods to enable/disable this feature:

• Through your authorized dealer,

• by using a power door unlock/lock sequence, or

• by using the keyless entry pad (if equipped).

• by using the instrument cluster message center. Refer to Message

center in the Instrument Cluster chapter.

Note: The autolock feature can be activated/deactivated independently

of the autounlock feature.

Before starting, ensure the ignition is in the off position and all vehicle

doors are closed. You must complete Steps 1–5 within 30 seconds or the

procedure will have to be repeated. If the procedure needs to be

repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and

turn the ignition to the on position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the on

position to the off position.

4. Press the power door unlock control on the door panel three times.

5. Turn the ignition back to the on position. The horn will chirp one time

to confirm programming mode has been entered and is active.

6. To enable/disable the autolock feature, press the unlock control, then

press the lock control. The horn will chirp once if autolock was

deactivated or twice (one short and one long chirp) if autolock was

activated.

7. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

Keyless entry keypad procedure

1. Turn the ignition to the 1 off

position.

2. Close all the doors.

3. Enter factory–set 5–digit entry

code.

102

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8.

5. Release the 7 • 8.

6. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been

enabled.

Autounlock feature

The autounlock feature will unlock all the doors when:

• the ignition is in the on position, all the doors are closed, and the

vehicle has been in motion at a speed greater than 12 mph (20 km/h);

• the vehicle has then come to a stop and the ignition is turned to the

off or accessory position; and

• the driver door is opened within 10 minutes of the ignition being

transitioned to the off or accessory position.

Note: The doors will not autounlock if the vehicle has been

electronically locked before the driver door is opened.

Deactivating/activating autounlock feature

Your vehicle comes with the autounlock features activated; there are four

methods to enable/disable this feature:

• Through your authorized dealer,

• by using a power door unlock/lock sequence, or

• by using the keyless entry keypad (if equipped) or

• by using the instrument cluster message center. Refer to Message

center in the Instrument Cluster chapter.

Note: The autounlock feature can be activated/deactivated

independently of the autolock feature.

Before starting, ensure the ignition is in the off position and all vehicle

doors are closed. You must complete Steps 1–5 within 30 seconds or the

procedure will have to be repeated. If the procedure needs to be

repeated, wait a minimum of 30 seconds before beginning again.

103

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

1. Place the key in the ignition and

turn the ignition to the on position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the on

position to the off position.

4. Press the power door unlock control on the door panel three times.

5. Turn the ignition back to the on position. The horn will chirp one time

to confirm programming mode has been entered and is active.

6. To enable/disable the autounlock feature, press the lock control, then

press the unlock control. The horn will chirp once if autounlock was

deactivated or twice (one short and one long chirp) if autounlock was

activated.

7. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

Keyless entry keypad procedure

1. Turn the ignition to the 1 off

position.

2. Close all the doors.

3. Enter factory–set 5–digit entry

code.

4. Press and hold the 3 • 4. While holding the 3 • 4, press and release

the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8 a

second time.

5. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been

enabled.

104

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

CHILDPROOF DOOR LOCKS

• When these locks are set, the

rear doors cannot be opened from

the inside.

• The rear doors can be opened

from the outside when the

childproof door locks are set, but

the doors are unlocked.

The childproof locks are located on

the rear edge of each rear door and

must be set separately for each

door. Setting the lock for one door will not automatically set the lock for

both doors.

• Insert the key and turn to the lock position (key at an angle) to

engage the childproof lock.

• Insert the key and turn to the unlock position (key horizontal) to

disengage the childproof lock.

INTERIOR LUGGAGE COMPARTMENT RELEASE

Your vehicle is equipped with a mechanical interior luggage compartment

release handle that provides a means of escape for children and adults in

the event they become locked inside the luggage compartment.

Adults are advised to familiarize themselves with the operation and

location of the release handle.

105

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

To open the luggage compartment

door (lid) from within the luggage

compartment, pull the illuminated

“T” shaped handle and push up on

the trunk lid. The handle is

composed of a material that will

glow for hours in darkness following

brief exposure to ambient light.

The “T” shaped handle will be

located either on the luggage

compartment door (lid) or inside

the luggage compartment near the

tail lamps.

WARNING: Keep vehicle

doors and luggage

compartment locked and keep

keys and remote transmitters out

of a child’s reach. Unsupervised

children could lock themselves in

the trunk and risk injury. Children

should be taught not to play in

vehicles.

WARNING: Do not leave children, unreliable adults, or animals

unattended in the vehicle. On hot days, the temperature in the

trunk or vehicle interior can rise very quickly. Exposure of people or

animals to these high temperatures for even a short time can cause

death or serious heat-related injuries, including brain damage. Small

children are particularly at risk.

106

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

REMOTE ENTRY SYSTEM

The Integrated Keyhead Transmitter (IKT) complies with part 15 of the

FCC rules and with RSS-210 of Industry Canada. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

The typical operating range for your IKT is approximately 33 feet

(10 meters). A decrease in operating range could be caused by:

• weather conditions,

• nearby radio towers,

• structures around the vehicle, or

• other vehicles parked next to your vehicle.

The IKT allows you to:

• remotely unlock the vehicle

doors.

• remotely lock all the vehicle

doors.

• remotely open the trunk.

• activate the personal alarm.

• arm and disarm the perimeter

anti-theft system.

• operate the illuminated entry

feature.

The remote entry lock/unlock feature operates in any ignition position

except while the key is held in the start position. The panic feature

operates with the key in the off position.

If there are problems with the remote entry system, make sure to take

ALL Integrated Keyhead Transmitters with you to the authorized

dealer in order to aid in troubleshooting the problem.

Unlocking the doors/two-stage unlock

1. Press

and release to unlock the driver’s door. Note: The interior

lamps will illuminate.

107

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

2. Press

and release again within five seconds to unlock all the doors.

The remote entry system activates the illuminated entry feature; this

feature turns on the lamps for 25 seconds or until the ignition is turned

to the on position.

The battery saver feature will turn off the lamps 30 minutes after the

ignition is turned to the off position.

Two-stage unlocking may be disabled or re-enabled by simultaneously

pressing the

and

controls on the IKT for four seconds (disabling

two-stage unlock allows all vehicle doors to unlock simultaneously). The

turn lamps will illuminate twice to indicate that two-stage unlock was

enabled or disabled.

Opening front windows and moon roof (if equipped)

You can open the vehicle’s windows, and (if equipped) vent the moon

roof by using the

control on the transmitter. Refer to Power

windows in the Driver Controls chapter for more information.

Locking the doors

1. Press

and release to lock all the doors. The turn lamps will flash.

2. Press

and release again within three seconds to confirm that all

the doors are closed. Note: The doors will lock again, the horn will chirp

and the turn lamps will illuminate once if all the doors and trunk are

closed.

Note: If any door or the trunk is not closed, or if the hood is not closed

in vehicles equipped with the perimeter alarm feature, the horn will

chirp twice and the lamps will not illuminate.

Car finder

Press

twice within three seconds. The horn will chirp and the turn

lamps will flash. It is recommended that this method be used to locate

your vehicle, rather than using the panic alarm.

Sounding a panic alarm

Press

to activate the alarm. The horn will sound and the turn lamps

will flash for a maximum of three minutes. Press again or turn the

ignition to the on position to deactivate, or wait for the alarm to time out

in three minutes.

Note: The panic alarm will only operate when the ignition is in the off

position.

108

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

Opening the trunk

Press twice within three seconds to open the trunk.

• Ensure that the trunk is closed and latched before driving your

vehicle. Failure to properly latch the trunk may cause objects to fall

out or block the driver’s rear view.

Replacing the battery

The integrated keyhead transmitter uses one coin type three-volt lithium

battery CR2032 or equivalent.

To replace the battery:

1. Twist a thin coin in the slot of the

IKT near the key ring in order to

remove the battery cover.

Note: Do not wipe off any grease on

the battery terminals on the back

surface of the circuit board.

2. Remove the old battery.

Note: Please refer to local

regulations when disposing of

transmitter batteries.

3. Insert the new battery. Refer to

the instructions inside the IKT for

the correct orientation of the

battery. Press the battery down to

ensure that the battery is fully

seated in the battery housing cavity.

4. Snap the battery cover back onto

the key.

Note: Replacement of the battery will not cause the IKT to become

deprogrammed from your vehicle. The IKT should operate normally after

battery replacement.

Replacing lost integrated keyhead transmitters (IKTs)

If you would like to have your integrated keyhead transmitters

reprogrammed because you lost one, or would like to buy additional

IKTs, you can either reprogram them yourself, or take all IKTs to your

authorized dealer for reprogramming.

109

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

How to reprogram your integrated keyhead transmitters (IKTs)

To program a new integrated keyhead transmitter yourself, refer to

Programming spare keys in the SecuriLock௡ passive anti-theft system

section of this chapter. Note: At least two IKTs are required to perform

this procedure yourself.

Illuminated entry

The interior lamps and puddle lamps (if equipped) illuminate when the

Integrated Keyhead Transmitter is used to unlock the door(s).

The illuminated entry system will turn off the lights if:

• the ignition is turned to the on position,

• the Integrated Keyhead Transmitter lock control is pressed,

• The vehicle is locked using the keyless entry keypad (if equipped), or

• after 25 seconds of illumination.

The lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

Perimeter lamps illuminated entry

With the Integrated Keyhead Transmitter system, the following items will

illuminate when the

• Parking lamps

• Tail lamps

control on the transmitter is pressed:

• Headlamps

The lamps will automatically turn off:

• if the ignition switch is turned to the 3 (on) position,

• The vehicle is locked using the keyless entry keypad (if equipped), or

• after 25 seconds of illumination.

Note: On some vehicles, the perimeter lamps illuminated entry feature

will not activate in daylight conditions.

Deactivating/activating perimeter lamps illuminated entry

You may enable/disable this feature by having your vehicle serviced by

your authorized dealer.

You may also perform the following power door lock sequence to

enable/disable the perimeter lamps feature. Note: Before starting, ensure

110

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

the ignition is in the 1 (off) position and all vehicle doors are closed. You

must complete Steps 1–5 within 30 seconds or the procedure will have

to be repeated. If the procedure needs to be repeated, wait a minimum

of 30 seconds before beginning again.

1. Place the key in the ignition and

turn the ignition to the 3 (on)

position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the 3 (on)

position to the 1 (off) position.

4. Press the power door unlock control on the door panel three times.

5. Turn the ignition back to the 3 (on) position. The horn will chirp one

time to confirm programming mode has been entered and is active.

6. Press the power door unlock control twice within five seconds.

Note: The horn will chirp once to indicate the perimeter lighting feature

has been deactivated. The horn will chirp once and honk once (one short

and one long) to indicate the perimeter lighting feature has been

activated.

7. Turn the ignition to the 1 (off) position to exit the procedure.

Note: The horn will chirp once to confirm the procedure is complete.

Illuminated exit

• When all vehicle doors are closed and the key is removed from the

ignition, the interior lamps and the puddle lamps (if equipped) will

illuminate.

The lamps will turn off if all the doors remain closed and

• 25 seconds elapse, or

• the key is inserted in the ignition.

Battery saver

The battery saver will shut off the lamps 30 minutes after the ignition

has been turned to the 1 (off) position.

• If the dome lamps were turned on using the panel dimmer control, the

battery saver will shut them off 30 minutes after the ignition has been

turned to the off position.

• If the courtesy lamps were turned on because one of the vehicle doors

or the trunk was opened, the battery saver will shut off them off

10 minutes after the ignition has been turned to the off position.

111

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security

• The battery saver will shut off the headlamps 10 minutes after the

ignition has been turned to the off position.

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)

You can use the keyless entry

keypad to:

• lock or unlock the doors without

using a key.

• open the trunk.

The keypad can be operated with the factory set 5–digit entry code; this

code is located on the owner’s wallet card in the glove box and is

available from your authorized dealer. You can also create up to three of

your own 5–digit personal entry codes.

When pressing the controls on the keypad, press the middle of the

controls to ensure a good activation.

Programming a personal entry code

To create your own personal entry code:

1. Enter the factory set code.

2. Within five seconds press the 1 • 2 on the keypad.

3. Enter your personal 5-digit code. Each number must be entered

within five seconds of each other.

4. The doors will lock then unlock to confirm that your personal keycode

has been programmed to the module.

Tips:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

• The factory set code will work even if you have set your own personal

code.

Erasing personal code

1. Enter the factory set 5–digit code.

2. Within five seconds, press the 1 • 2 on the keypad and release.

3. Press and hold the 1 • 2 for two seconds. This must be done within

five seconds of completing Step 2.

All personal codes are now erased and only the factory set 5–digit code

will work.

112

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security -> Locks for Your Ford Fusion 4 Door First Generation (2006-2012)

Related Topics

Locks and Security

Popular Owner Manuals

Latest Owner Manuals