Get QUICK START Guide for Ford Ka 2 Door Second Generation (2009-2016)

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 1

DASHBOARD (LEFT-HAND DRIVE)

The presence and position of controls, instruments and gauges may vary depending on the versions.

KA00177m

1. Side air vent – 2. Left steering column stalk: external lights – 3. Instrument panel and warning lights – 4. Right steering column

stalk: windscreen wiper, washer, trip computer controls – 5. Central air vents – 6. Oddment/Car radio compartment –

7. Passenger side air bag – 8. Oddment compartment – 9. Heating/ventilation/climate controls – 10. Power windows controls –

11. Gear lever – 12. Control plate – 13. Driver side air bag

1

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 2

DASHBOARD (RIGHT-HAND DRIVE)

The presence and position of controls, instruments and gauges may vary depending on the versions.

KA00178m

1. Side air vent – 2. Passenger side air bag – 3. Central air vents – 4. Oddment/Car radio compartment – 5. Left steering column

stalk: external lights – 6. Instrument panel and warning lights – 7. Right steering column stalk: windscreen wiper, washer, trip

computer controls – 8. Driver side air bag – 9. Control plate – 10. Power windows controls – 11. Gear lever –

12. Heating/ventilation/climate control – 13. Oddment compartment

2

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 3

ON BOARD PANEL AND INSTRUMENTS

Left-hand drive versions

A

B

C

D

A Speedometer (speed indicator).

B Fuel gauge with reserve warning

light.

C Engine coolant temperature gauge

with excess temperature warning

light.

D Rev. counter.

E Digital display.

Warning lights

and

E

are only

m

E

KA00161m

provided on Diesel versions.

Versions with digital display

KA00162m

Versions with multifunction display

3

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 4

Right-hand drive versions

A

B

C

D

A Rev. counter.

B Fuel gauge with reserve warning

light.

C Engine coolant temperature gauge

with excess temperature warning

light.

D Speedometer (speed indicator).

E Digital display.

Warning lights

and

E

are only

m

provided on Diesel versions.

E

KA00163m

Versions with digital display

KA00164m

Versions with multifunction display

4

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 5

DIGITAL DISPLAY

E

D

STANDARD SCREEN

The standard screen shows the

following information:

A Headlight aiming position

(only with dipped beam

headlights on)

KA00165m

KA00016m

B Time (always displayed, even with

key extracted and front doors

– To scroll the displayed menu

Management modes differ according to

the option selected.

closed)

and the related options downwards

or to decrease the displayed value.

C Gear Shift Indication

The menu includes the following

functions:

D Odometer (display of covered

km or miles)

SETUP MENU

– HOUR

– BUZZ

E Auto-Start-Stop function indication

The menu comprises a series of

functions arranged in a cycle which can

be selected through buttons + and –

to access the different select operations

and settings (setup) given in the

following paragraphs.

Note With key removed (when

opening one of the front doors)

the display will turn on and show for

a few seconds the km or mi covered.

– SPEED

– UNIT

– P BAG (*)

The setup menu can be activated by

pressing briefly button MENU ESC

CONTROL BUTTONS

.

+ To scroll the displayed menu and

the related options upwards or to

increase the displayed value.

(*) Function activated only by taking car

to dealership.

Single presses on the + and – buttons

will scroll the setup menu options.

MENUPress briefly to display

in the menu and/or go to next

screen or confirm the

required menu option.

ESC

Hold pressed to go back

to the standard screen.

5

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 6

MULTIFUNCTION

DISPLAY

(where provided)

E

The car can be equipped with the

multifunction display that, depending on

previous settings, shows useful

information when driving.

D

KA00166m

KA00016m

“STANDARD” SCREEN

The standard screen shows

the following information:

Single presses on buttons + or – will

MENU Press briefly to display

scroll the setup menu options.

Operating modes are different

according to the characteristics

of the option selected.

in the menu and/or go to

next screen or confirm

the required menu option.

Hold pressed to go back

to the standard screen.

ESC

A Outside temperature

B Time (always displayed, even with key

extracted and front doors closed)

C Auto-Start-Stop function indication

D Gear Shift Indication

The menu includes the following

functions:

– MENÙ

– SPEED BEEP

– TRIP B DATA

– SET TIME

– SET DATE

– SEE RADIO

– MEASUREMENT UNIT

– LANGUAGE

– WARNING VOLUME

– KEY VOL.

– PASSENGER AIR BAG (*)

– COURTESY LIGHTS

– EXIT MENU

(*) Function activated only by taking car

to dealership.

– To scroll the displayed menu and the

related options downwards or to

decrease the displayed value.

E Odometer (covered km or miles)

F Date

G Headlight aiming position (only with

dipped beam headlights on)

SETUP MENU

The menu comprises a series of

Note When one of the front doors is

opened, the display turns on and shows

the time and distance covered (in km or

mi) for a few seconds.

functions arranged in a cycle which can

be selected through buttons + and – to

access the different select operations

and settings (setup) given in the

following paragraphs. There is a

CONTROL BUTTONS

submenu for some items (clock

+ To scroll the displayed menu and

the related options upwards or to

increase the displayed value.

adjustment and units of measurement).

The setup menu can be activated by

pressing briefly button MENU ESC

.

6

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 7

C

IP

TR

KA00206m

KA00185m

KA00017m

LOCKING

STEERING WHEEL

TRIP COMPUTER

AND RELEASING WITH

REMOTE CONTROL

It can be adjusted vertically (where

provided).

General information

The Trip computer is used to display

information on car operation when the

key is turned to MAR-ON. This

function includes two separate trips,

namely “Trip A” and “Trip B”.

For adjustment, bring the lever

downward to position 2 then position

the wheel and lock it bringing lever to

position 1.

Press the release button A to open

the door.

Press the lock button B to activate

the central locking.

The “Trip A” displays:

Press the button C pressing twice

for a few seconds to open the tailgate.

❒

Range

Distance

Average consumption

Instantaneous consumption

Average speed

Trip time (driving time).

The “Trip B” displays:

❒

Distance B

Average consumption B

Average speed B

Trip time B (driving time)

Reset trip B

7

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 8

WINDOW WASHING

E

A

WINDSCREEN WASHER/WIPER

The stalk has five different positions

(four speed levels):

B

A windscreen wiper off.

B intermittent operation.

C continuous slow operation.

D continuous fast operation.

E fast temporary operation

(spring-return position).

C

D

KA00109m

KA00111m

FLASHING THE HEADLIGHTS

EXTERNAL LIGHTS

“Smart washing” function

You can flash the beams pulling the stalk

toward the steering wheel (unstable

position).

The left-hand stalk operates most of the

external lights. The external lights can

only be switched on when the ignition

key is on MAR-ON. The instrument

panel and the various dashboard

controls will come on with the external

lights.

Pull the stalk towards the steering

wheel (unstable position) to operate the

windscreen washer. The front window

wiper is automatically activated and

finishes three strokes after the control

has been released, m aking a further

stroke to remove the residual drops.

DIRECTION INDICATORS

Bring the lever to the (stable) position:

up (position a): activates the right

direction indicator;

down (position b): activates the left

direction indicator.

LIGHTS OFF

REAR WINDOW

WASHER/WIPER

Knurled ring turned to position O.

Turn the knurled ring to

to operate

'

SIDE LIGHTS

the rear window wiper. Pushing the

stalk towards the dashboard (unstable

position) will activate the rear window

washer. The rear window wiper is

automatically activated and finishes

three strokes after the control has been

released, making a further stroke to

remove the residual drops. With the

windscreen wiper in use, if reverse gear

is engaged, the rear window wiper is

automatically activated.

Turn the knurled ring to position

6

.

DIPPED BEAM HEADLIGHTS

Turn the knurled ring to position

2

.

MAIN BEAM HEADLIGHTS

With knurled ring in position 2, push

the stalk forward toward the dashboard

(steady position).

8

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 9

KA00203m

KA00209m

KA00204m

AIR VENTS

MANUAL CLIMATE CONTROL

Adjustment: move the vent, directing

A Air temperature knob (red-hot/blue-cold).

B Fan speed knob and climate control system activation/deactivation.

C Air recirculation knob.

it as required.

Opening: to open the vent, press in

the point shown by the arrow.

D Air distribution knob.

E Heated rear window activation/deactivation button.

F Heated windscreen activation/deactivation button.

9

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 10

A

KA00060m

USING THE MANUAL

GEARBOX

To engage the gears, press the clutch

pedal fully and shift the gear lever into

one of the required positions (the

diagram is shown on the lever knob).

KA00191m

Buttons +, –, F

Adjusting fan speed

AUTOMATIC CLIMATE

To engage reverse R from neutral, raise

ring A under the knob and at the same

time move the gearshift lever

CONTROL

Buttons y μ ∂ - G H I

Air distribution manual selection

Button - L

Button AUTO - A

Activation of the automatic function of

the climate control system

A/C button - B

compressor activation/deactivation

OFF button - C

Switching off the system

rightwards and then backward.

-

Front windows quick

demisting/defrosting.

Heated rear window

defrosting/demisting

Press button M to activate the function.

…

button - D

Air recirculation on/off

Heated windscreen

defrosting/demisting

Buttons +, –, E

Setting desired temperature

Press button N to activate the function.

10

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 11

OPERATING MODES

Engine stopping mode

With the vehicle stationary, the engine

stops with the gearbox in neutral and

the clutch pedal released.

AUTO-START-STOP

SYSTEM

INTRODUCTION

The Auto-Start-Stop device

automatically stops the engine each time

the vehicle is stationary and starts it

again when the driver wants to resume

driving.

This improves the efficiency of the

vehicle by reducing fuel consumption,

the emission of harmful gases and noise

pollution.

A

Note The Auto-Start-Stop function

is automatically turned off if the speed

of 10 km/h is not exceeded for about

2 seconds, to prevent the engine from

being repeatedly stopped when driving

at walking pace.

KA00205m

CONTROLS

The engine being stopped is signalled

by a symbol

on the display.

The system operates every time the car

is started.

FRONT FOG LIGHTS

AND REAR FOG LAMPS

(where provided)

Engine restarting mode

Note if climate comfort is to

Depress the clutch pedal to restart

the engine.

be favoured, the Start&Stop system can

be disabled, for a continuous operation

of the climate control system.

To turn on the front/rear fog lights,

use the button A as follows:

MANUAL ACTIVATION AND

DEACTIVATION

The device can be activated/deactivated

1° Pressing: front fog lights on

2° Pressing: rear fog lamps on

3° Pressing: lights/lamps off.

When the front fog lights are on,

by the button

in the dashboard

(see “Controls” paragraph).

the warning light

turns on in

5

the instrument panel; when the rear fog

lamps are on, the warning light 4 turns

on in the instrument panel.

The front fog lights are activated when

the dipped headlights are on.

11

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 12

ENGINE STOPPING FAILURE

CONDITIONS

With the device activated, for reasons

of comfort, limiting emissions and

safety, the engine does not stop in

certain conditions, including:

❒

driver’s door not shut;

SEATS

driver’s seat belt not fastened;

FRONT SEATS

reverse gear engaged (for example,

for parking manoeuvres);

Fore/aft adjustment

Lift lever A and push the seat forwards

and backwards.

❒

automatic climate control is on and

a comfortable temperature has not

yet been reached or MAX – DEF

function enabled;

❒

engine still cold;

fault in the components or sensor of

the Auto-Start-Stop system;

Heated seats

❒

during the first period of use,

to initialise the system.

Press the button E to switch the

function on/off.

❒particularly cold outside

temperatures, where the appropriate

indication is provided;

In the above cases, a message appears

in the display and, where provided,

the warning light blinks

Backrest angle adjustment

❒

reduced braking system vacuum,

e.g. following the brake pedal being

pressed repeatedly;

.

Turn knob B.

Height adjustment

❒

battery not sufficiently charged;

heated rear window activated;

heated windshield;

Operating lever C it is possible to lift

or lower the rear area of the cushion

to achieve the most comfortable driving

position.

windscreen wipers working at

maximum speed for a long time;

❒

particulate filter regeneration

in progress (diesel engines only);

12

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 13

2

6

C

1

E

5

D

A

3

4

KA00006m

KA00008m

KA00018m

Driver side, where equipped with

position memory

Driver side and passenger side

where not equipped with position

memory

To return the seat to its initial position,

slide the seat back and press on the

backrest to lock the seat (movement

d); operate lever D (movement e)

and raise the backrest (movement f)

until it clicks home.

To return the seat to its initial position,

slide the seat back and press on the

backrest to lock the seat (movement

d); operate lever D (movement e)

and raise the backrest (movement f)

until it clicks home. Adjust lengthwise

according to the instructions in

B

ATTENTION Using lever D before

locking the seat in its original position

causes the original seat position to be

lost. In this case, adjust the seat position

by means of the lengthwise adjustment

according to the instructions in

KA00007m

paragraph “Lengthwise adjustment”.

Backrest tilt

To tilt the seat, operate lever D

(movement a) and push the backrest

forward to lock (movement b); release

lever D and push the backrest to slide

the seat forward (movement c, applies

only to seats with easy entry).

ATTENTION

All adjustments must be

made with the car

paragraph “Lengthwise adjustment”.

stationary.

13

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 14

A

B

A

B

A

C

KA00019m

KA00035m

KA00043m

REAR SEATS

FRONT POWER

FUEL TANK CAP

The cap B is provided with a loss

prevention device C which secures it to

the lid A.

Using the ignition key, undo the cap B

turning it anticlockwise.

Backrest release

WINDOW CONTROLS

(where provided)

❒

For versions with joint seat,

lift handles A and B and guide

the backrest onto the cushion.

For versions with split seats,

lift handle A or B to release

The two buttons are located besides

the gearshift lever (one for each side);

they control:

respectively the left or right part of

the backrest and guide the backrest

onto the cushion.

A To open/close the left front

window.

B To open/close the right front

Taking the seat back in the standard use

position

window.

Proceed as follows:

❒

move the seat belts to the side,

making sure that they are correctly

extended and not twisted;

raise the seat backrests and push

them back until hearing the locking

click of both retainers.

14

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 15

❒

On your mobile phone, search for

❒

Ford Audio asks you if you want to

copy the mobile phone phonebook

just registered on the Ford Audio

system. You are advised to copy the

phonebook.

To proceed with copying, say “Yes”;

if you do not want to copy the

phonebook, say “No”.

FORD AUDIO

devices equipped with Bluetooth^®

technology (the setting on your

mobile phone might be called

Search or New Device). Find “Ford

Audio” in this list (the name that

identifies the Ford Audio system

in your vehicle) and select it.

GENERAL FUNCTIONS

Turning

the system on: ON/OFF button pressed

Off:

ON/OFF button long

pressed

When the mobile phone requests it,

enter the PIN displayed on the

instrument panel display with your

mobile phone keypad. If pairing

is successful, the system will say

“Connecting” and at the end the

display will show, as confirmation,

the ID of the paired mobile phone.

On some compatible mobile phones

the names in the directory are not

copied automatically, but have to be

transferred by the user using the

mobile phone keypad.

HOW TO PAIR YOUR MOBILE

PHONE

IMPORTANT This operation should

only be carried out with the car

stationary.

To pair your mobile phone, proceed as

follows:

If Ford Audio asks you to do this,

perform this procedure following

the instructions specific to your

mobile phone and press /MAIN

ß

It is essential to wait until you see this

confirmation message on the display.

Pressing /MAIN or /ESC before

when you have finished.

❒

Press

and say “Settings” then,

}

&

ß

Ford Audio

at the end of the

the message is displayed may cancel

the pairing process.

message say “Pairing”.

The system will show the phone

pairing PIN number on the

multifunction display. For the next

two steps, consult your mobile

phone manual regarding Bluetooth^®

pairing.

If the registration fails, an error

message will appear; in this case, you

will need to repeat the procedure.

❒

After registering the mobile

phone, when you first connect,

Ford Audio will say “Welcome”.

In the subsequent registration

procedures or connection of the

same phone, this message will not be

said anymore.

15

603.95.157 PP KA EN 1ed trip 15-10-2010 13:49 Pagina 16

Print no. 603.95.157 - 11/2010 - 1st Edition

QUICK START for Your Ford Ka 2 Door Second Generation (2009-2016)

Related Topics

Popular Owner Manuals

Latest Owner Manuals