2014-2022 Ford Mondeo 4 Door Lighting User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Lighting for Your Ford Mondeo 4 Door Fifth Generation (2014-2022)

Lighting  
One side  
LIGHTING CONTROL  
Lighting control positions  
A
B
Right-hand side  
Left-hand side  
High and low beam  
A
B
C
Off  
Side and tail lamps  
Headlamps  
Parking lamps  
Pull the lever fully towards the steering  
wheel to switch between high and low  
beam.  
CAUTION  
Prolonged use of the parking lamps  
will discharge the battery.  
Headlamp flasher  
Pull the lever slightly towards the steering  
Switch off the ignition.  
wheel.  
Both sides  
Set the lighting control to position B.  
Home safe lighting  
Switch the ignition off and pull the  
direction indicator lever towards the  
steering wheel to switch the headlamps  
on. You will hear a short tone. The  
headlamps will go off automatically after  
three minutes with any door open, or 30  
seconds after the last door has been  
closed.  
45  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
With all doors closed, but within the 30  
WARNINGS  
second delay, opening any door will result  
in the three minute timer starting again.  
A manual override may be required  
when approaching other road users  
such as cyclists.  
The home safe lights can be cancelled by  
either pulling the direction indicator lever  
towards the steering wheel again or by  
turning the ignition switch on.  
Do not use the system in fog.  
CAUTIONS  
AUTOLAMPS  
In cold and severe weather conditions  
the system may not function. A  
manual override may be necessary in  
these cases.  
Reflective road signs may be detected  
as oncoming traffic and the  
headlamps may be switched to low  
beam.  
If the lights of oncoming vehicles are  
hidden by obstacles (for example  
guard rails) the system may not  
deactivate the high beam.  
Always fit Ford Original Parts when  
replacing headlamp bulbs. Other  
bulbs may reduce system  
performance.  
Note: If you have switched autolamps on,  
you can only switch the high beam on when  
autolamps has switched the headlamps on.  
The headlamps will come on and go off  
automatically depending on the ambient  
light.  
Check and replace wiper blades  
regularly to ensure the camera sensor  
has a clear view through the  
DAYTIME RUNNING LAMPS  
windscreen. Replacement wiper blades  
must be the correct length.  
The lamps will illuminate when the ignition  
is on.  
Note: Keep the windscreen free from  
obstructions such as bird droppings, insects  
and snow or ice.  
AUTOMATIC HIGH BEAM  
CONTROL  
The system will automatically switch on  
main beam if it is dark enough and no other  
traffic is present. If it detects an  
WARNINGS  
approaching vehicle’s headlamps or tail  
lamps, or street lighting ahead the system  
will switch off main beam before it can  
distract other road users. Dipped beams  
will remain on.  
The system does not relieve you of  
your responsibility to drive with due  
care and attention. A manual  
override may be necessary if the system  
fails to switch the main beam on or off.  
46  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
A camera sensor is centrally mounted  
Note: The system may take a short time to  
initialize after first switching the ignition on,  
especially in very dark conditions. The high  
beam will not automatically switch on  
during this period.  
behind the windshield of the vehicle, and  
monitors conditions continuously to decide  
when to switch the high beam off and on.  
Once the system is active the high beam  
will switch on if:  
Setting the system sensitivity  
•
•
•
It is dark enough to require the use of  
high beams and  
The system has three sensitivity levels  
which can be accessed via the information  
display. See InformationDisplays (page  
75).  
The sensitivity determines the speed at  
which the high beam will be restored after  
detected traffic leaves the field of view.  
there is no traffic or street lighting  
ahead and  
vehicle speed is greater than 40 km/h  
(25 mph).  
The high beam will switch off if:  
•
The ambient light is high enough that  
Manually overriding the system  
high beam is not required.  
•
An approaching vehicle's headlamps  
or tail lamps are detected.  
•
•
Street lighting is detected.  
Vehicle speed falls below 25 km/h (16  
mph).  
•
The camera sensor is too hot or  
becomes blocked.  
Activating the system  
Use the high beam lever to switch between  
high beam and low beam.  
Note: This is a temporary override and the  
system will return to automatic operation  
after a short period.  
Switch on the system using the information  
display and autolamps. See Information  
Displays (page 75). See Autolamps  
(page 46).  
To permanently deactivate the system use  
the information display menu or turn the  
lighting control switch from autolamps to  
headlamps.  
Turn the switch to the autolamps position.  
47  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
Note: Only use the rear fog lamps when  
FRONT FOG LAMPS  
visibility is restricted to less than 50 meters  
(164 feet).  
Note: Do not use the rear fog lamps when  
it is raining or snowing and visibility is more  
than 50 meters (164 feet).  
HEADLAMP LEVELING  
Note: Vehicles with Xenon headlamps are  
equipped with automatic headlamp  
leveling.  
WARNING  
Only use the front fog lamps when  
visibility is considerably restricted by  
fog, snow or rain.  
REAR FOG LAMPS  
A
B
Raised headlamp beams  
Lowered headlamp beams  
You can adjust the level of the headlamp  
beams according to the vehicle load.  
Recommended headlamp leveling switch positions  
Load  
Load in luggage  
compartment  
Switch position  
Front seats  
Second row seats  
1-2  
1-2  
-
-
-
-
0
0 (0.52)  
1 (0.52)  
1-2  
3
-
48  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
Load  
Load in luggage  
Switch position  
compartment  
Front seats  
Second row seats  
Max1  
Max1  
3 (0.52)  
4 (1.52)  
1-2  
3
1
-
1
See Vehicle identification (page 250).  
2 Vehicles with active suspension.  
ADAPTIVE HEADLAMPS  
A
B
without AFS  
with AFS  
The system will not operate when the  
vehicle is stationary, when you have  
switched on the daytime running lamps or  
when you have selected reverse gear.  
The AFS adjusts the headlamp low beam  
depending on vehicle direction and speed.  
It improves visibility when you are driving  
at night and helps to reduce headlamp  
glare for oncoming drivers.  
49  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
A message will appear in the information  
headlamps will move to a fixed central or  
low beam position. Have the system  
checked as soon as possible.  
display if the system malfunctions. See  
Information Messages (page 88). The  
Cornering lamps  
A
B
Headlamp beam  
Cornering lamp beam  
The cornering lamps illuminate the inside  
of a corner when you are turning.  
DIRECTION INDICATORS  
50  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
Note: Tap the lever up or down to make the  
Reading lamps  
direction indicators flash only three times.  
INTERIOR LAMPS  
Courtesy lamp  
If you switch off the ignition, the reading  
lamps will go off automatically after some  
time to prevent the vehicle battery from  
discharging. To switch them back on,  
switch on the ignition for a short time.  
LED Interior lighting  
Note: Individual lamps may be switched on  
independently, but not off if all lamps have  
been switched on by the driver.  
Note: All other lamps will be either  
non-switchable or with individual reading  
or dome lamp functionality only.  
A
B
C
Off  
Door contact  
On  
If you set the switch to position B, the  
courtesy lamp will come on when you  
unlock or open a door or the luggage  
compartment lid. If you leave a door open  
with the ignition switch off, the courtesy  
lamp will go off automatically after some  
time to prevent the vehicle battery from  
discharging. To switch it back on, switch  
on the ignition for a short time.  
The lamps will come on when you unlock  
or open a door or the luggage  
compartment lid. If you leave a door open  
with the ignition switch off, all lamps will  
go off automatically after some time to  
prevent the vehicle battery from  
discharging. To switch them back on,  
switch on the ignition for a short time.  
The courtesy lamp will also come on when  
you switch off the ignition. It will go off  
automatically after a short time or when  
you start or restart the engine.  
If you set the switch to position C with the  
ignition switch off, the courtesy lamp will  
come on. It will go off automatically after  
a short time to prevent the vehicle battery  
from discharging. To switch it back on,  
switch on the ignition for a short time.  
51  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
Side mounted lamp  
Center mounted lamp  
A
B
Right-hand side reading lamp on  
and off switch  
A
B
C
Reading lamp on and off switch  
Door function switch  
All lamps on and off switch  
Left-hand side reading lamp on  
and off switch  
C
D
Door function switch  
All lamps on and off switch  
If you press switch B all lamps remain off  
when the door is opened. Press the switch  
again to reverse.  
You can control all lamps using switch C.  
If you press switch C all lamps remain off  
when the door is opened. Press the switch  
again to reverse.  
You can control all lamps using switch D.  
52  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
1. Open the hood. See Opening and  
Closing the Hood (page 169).  
Vanity mirror lamps  
A
B
Off  
On  
2. Remove the screws.  
If you switch off the ignition, the vanity  
mirror lamps will go off automatically after  
a short time to prevent the vehicle battery  
from discharging. To switch them back on,  
switch on the ignition for a short time.  
ADJUSTING THE HEADLAMPS  
To adjust the headlamps for driving on the  
left or right hand side of the road, see your  
dealer.  
HAZARDWARNINGFLASHERS  
3. Remove the plastic screw and retainer.  
For item location: See At a Glance (page  
9).  
REMOVING A HEADLAMP  
WARNING  
Have Xenon bulbs changed by a  
trained technician. There is a risk of  
electric shock.  
53  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
Note: When fitting the headlamp, make  
sure that you fully engage the headlamp in  
the lower outer fixing point.  
Note: When fitting the headlamp, tighten  
the front screw first and then the rear screw.  
CHANGING A BULB  
WARNINGS  
Switch the lights and the ignition off.  
Let the bulb cool down before  
removing it.  
4. Carefully pull the corner of the grille  
and bumper towards the front of the  
vehicle.  
Have Xenon bulbs changed by a  
trained technician. There is a risk of  
electric shock.  
5. Carefully lift the corner of the  
headlamp and push it as far as possible  
towards the back of the vehicle.  
CAUTIONS  
Do not touch the glass of the bulb.  
Only fit bulbs of the correct  
specification. See Bulb  
Specification Chart (page 60).  
Note: The following instructions describe  
how to remove the bulbs. Fit replacements  
in the reverse order unless otherwise stated.  
Headlamp  
Note: Remove the covers to gain access to  
the bulbs.  
Direction indicator  
6. Carefully pull the headlamp towards  
the center of the vehicle, behind the  
grille and bumper, to disengage it from  
the lower outer fixing point.  
1. Remove the headlamp. See  
Removing a Headlamp (page 53).  
7. Remove the headlamp.  
CAUTION  
When fitting the headlamp, take care  
not to damage the locating points.  
54  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
2. Turn the bulb holder counterclockwise  
and remove it.  
3. Remove the bulb.  
2. Turn the bulb holder counterclockwise  
and remove it.  
3. Gently press the bulb into the bulb  
holder, turn it counterclockwise and  
remove it.  
Cornering lamp  
1. Remove the headlamp. See  
Removing a Headlamp (page 53).  
Headlamp main beam  
1. Remove the headlamp. See  
Removing a Headlamp (page 53).  
2. Disconnect the electrical connector.  
3. Release the clip and remove the bulb.  
Daytime running lamps  
2. Disconnect the electrical connector.  
3. Release the clip and remove the bulb.  
Note: These are not serviceable items,  
please consult your dealer if they fail.  
Headlamp dipped beam  
1. Remove the headlamp. See  
Removing a Headlamp (page 53).  
55  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
3. Remove the bulb.  
Approach lamp  
Note: Position the mirror glass as far  
inwards as possible.  
Side repeater  
1. Insert a screwdriver into the gap  
between the mirror housing and the  
mirror glass and release the metal  
retaining clip.  
1. Carefully remove the side repeater.  
2. Remove the lamp.  
3. Remove the bulb.  
2. Remove the bulb holder.  
56  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
Front fog lamps  
Rear lamps  
Direction indicator  
1. Remove the trim panel.  
Note: You cannot separate the fog lamp  
bulb from the bulb holder.  
Note: Do not remove the screws.  
1. Loosen the screws.  
2. Remove the lamp.  
3. Disconnect the electrical connector.  
4. Turn the bulb holder counterclockwise  
and remove it.  
2. Turn the bulb holder counterclockwise  
and remove it.  
3. Gently press the bulb into the bulb  
holder, turn it counterclockwise and  
remove it.  
Rear and brake lamp  
Note: These are not serviceable items,  
please consult your dealer if they fail.  
57  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
Reversing lamp and fog lamp  
License plate lamp  
1. Carefully release the spring clip.  
2. Remove the lamp.  
3. Remove the bulb.  
1. Remove the trim panel.  
Interior lamps  
Vehicles with LED lamps  
Note: These are not serviceable items,  
please consult your dealer if they fail.  
2. Turn the bulb holder counterclockwise  
and remove it.  
3. Gently press the bulb into the bulb  
holder, turn it counterclockwise and  
remove it.  
Central high mounted brake lamp  
Note: These are not serviceable items,  
please consult your dealer if they fail.  
58  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
Vehicles without interior sensors  
Reading lamps  
Vehicles without interior sensors  
1. Carefully prise out the lens.  
2. Remove the lens.  
3. Remove the bulb.  
1. Carefully prise out the lens.  
2. Remove the lens.  
3. Remove the bulb.  
Vehicles with interior sensors  
Vehicles with interior sensors  
1. Carefully prise out the lens.  
2. Remove the lens.  
3. Remove the bulb.  
1. Carefully prise out the lamp.  
2. Turn the bulb holder counterclockwise  
and remove it.  
59  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
1. Carefully prise out the lamp.  
2. Remove the bulb.  
Luggage compartment lamp  
3. Remove the bulb.  
Vanity mirror lamp  
1. Carefully prise out the lamp.  
2. Remove the bulb.  
BULB SPECIFICATION CHART  
Lamp  
Front direction indicator  
Headlamp main beam  
Headlamp dipped beam  
Cornering lamp  
Specification  
PY21W  
H1  
Power (watt)  
21  
55  
55  
55  
5
H7  
H1  
Side repeater  
W5W  
W5W  
H8  
Approach lamp  
5
Front fog lamp  
35  
5
Side lamp  
W5W  
60  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  
Lighting  
Lamp  
Rear direction indicator  
Rear fog lamp  
Specification  
Power (watt)  
PY21W  
H21W  
P21W  
21  
21  
21  
5
Reversing lamp  
License plate lamp  
Interior lamp  
W5W  
Festoon  
BA9s  
10  
5
Reading lamp  
Vanity mirror lamp  
Luggage compartment lamp  
W5W  
W6W  
5
6
61  
Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013  

Related Topics

Lighting Control Autolamps Daytime Running Lamps Automatic High Beam Control Front Fog Lamps Rear Fog Lamps Headlamp Leveling Adaptive Headlamps Direction Indicators Interior Lamps Adjusting the Headlamps Hazard Warning Flashers Removing a Headlamp Changing a Bulb Bulb Specification Chart

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot