Get Locks and Security Guide for Ford Mustang 2 Door Fifth Generation (2005-2014)

KEYS

Your vehicle may be equipped with

two Integrated Keyhead

Transmitters (IKTs). The key blade

functions as a programmed key

which starts the vehicle and

unlocks/locks all the doors. The

transmitter portion functions as the

remote entry transmitter.

Your IKTs are programmed to your vehicle; using a non-programmed key

will not permit your vehicle to start. If you lose your authorized dealer

supplied IKTs, replacement IKTs are available through your authorized

dealer. Standard SecuriLock威 keys without remote entry transmitter

functionality can also be purchased from your authorized dealer if

desired.

Always carry a spare key with you in case of an emergency.

For more information regarding programming replacement IKTs, refer to

the SecuriLock威 passive anti-theft system section later in this chapter.

Note: Your vehicle’s IKTs were

issued with a security tag that

provides important vehicle key cut

information. It is recommended that

you keep the tag in a safe place for

future reference.

POWER DOOR LOCKS

The power door lock controls are located on the driver and front

passenger door panels.

Locks and Security

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

Press the control to unlock all

doors.

Press the

control to lock all

doors.

Locking and unlocking with keys

Your vehicle’s keys are designed to lock and unlock the driver’s door, as

well as open the trunk.

• The driver’s door is unlocked when the key is inserted in the driver

door key cylinder and turned to the unlock position. The driver’s door

is locked when the key is inserted in the driver door key cylinder and

turned to the lock position.

Note: If the vehicle is not equipped with active anti-theft system, locking

the driver door with the key does not lock the passenger door. Use the

power door lock control or manually lock the passenger door to ensure

the vehicle is properly secured.

Smart locks

This feature helps prevent you from locking yourself out of the vehicle if

your key is still in the ignition.

When you open the driver’s door and you lock the vehicle with the

power door lock control, all the doors will lock, then the driver’s door

will automatically unlock reminding you that your key is still in the

ignition.

The vehicle can still be locked, with the key in the ignition, using the

manual lock button on the door, locking the driver’s door with a key or

using the lock button on the remote entry transmitter.

Autolock (if equipped)

The autolock feature will automatically lock all vehicle doors when:

• all doors are closed,

• the ignition is in the on position,

• you shift into any gear putting the vehicle in motion, (for manual

transmission, the parking brake should not be engaged) and

• the vehicle attains a speed greater than 12 mph (20 km/h).

Locks and Security

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

The autolock feature repeats when:

• any door is opened then closed while the ignition is in the on position

and the vehicle speed is 9 mph (15 km/h) or lower, and

• the vehicle attains a speed greater than 12 mph (20 km/h).

Deactivating/activating autolock

Your vehicle comes with the autolock feature enabled. There are three

methods to enable/disable this feature:

• Through your authorized dealer, or

• performing the power door lock control procedure, or

• performing the message center procedure. Refer to Message center in

the Instrument Cluster chapter.

Note: The autolock feature can be activated/deactivated independently

of the autounlock feature.

Before following the activation or deactivation procedures, make sure

that the active anti-theft system is not armed, ignition is in the off

position, and all vehicle doors are closed.

Power door unlock/lock procedure

You must complete Steps 1-5 within 30 seconds or the procedure will

have to be repeated. If the procedure needs to be repeated, you must

wait 30 seconds.

Note: All doors must be closed and remain closed throughout the

configuration process.

1. The ignition must be off to begin

sequence.

2. Turn the ignition to the on

position.

3. Press the power door unlock

control three times.

4. Turn the ignition from the on to

the off position.

5. Press the power door unlock control three times.

6. Turn the ignition back to the on position. The horn will chirp.

7. Press the unlock control, then press the lock control. The horn will

chirp once if autolock was deactivated or twice (one short and one long

chirp) if autolock was activated.

Locks and Security

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

8. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

Autounlock (if equipped)

The autounlock feature will unlock all the doors when:

• the ignition is in the on position, all the doors are closed, and the

vehicle has been in motion at a speed greater than 12 mph (20 km/h);

• the vehicle has then come to a stop and the ignition is turned to the

off or accessory position; and

• the driver door is opened within 10 minutes of the ignition being

turned to the off or accessory position.

Note: The doors will not autounlock if the vehicle has been

electronically locked before the driver door is opened.

Deactivating/activating autounlock

Your vehicle comes with the autounlock feature activated. There are

three methods to enable/disable this feature:

• Through your authorized dealer, or

• by using the power door unlock/lock sequence,

• by using the instrument cluster message center. Refer to Message

center in the Instrument Cluster chapter.

Note: The autounlock feature can be activated/deactivated

independently of the autolock feature.

Power door lock switch autounlock enable/disable procedure

Before starting, ensure the ignition is in the off position and all vehicle

doors are closed. You must complete Steps 1–5 within 30 seconds or the

procedure will have to be repeated. If the procedure needs to be

repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and

turn the ignition to the on position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the on

position to the off position.

4. Press the power door unlock control on the door panel three times.

5. Turn the ignition back to the on position. The horn will chirp one time

to confirm programming mode has been entered and is active.

Locks and Security

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

6. To enable/disable the autounlock feature, press the lock control, then

press the unlock control. The horn will chirp once if autounlock was

deactivated or twice (one short and one long chirp) if autounlock was

activated.

7. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

INTERIOR LUGGAGE COMPARTMENT RELEASE

Your vehicle is equipped with a mechanical interior luggage compartment

release handle that provides a means of escape for children and adults in

the event they become locked inside the luggage compartment.

Adults are advised to familiarize themselves with the operation and

location of the release handle.

To open the luggage compartment

door (lid) from within the luggage

compartment, pull the illuminated

“T” shaped handle and push up on

the trunk lid. The handle is

composed of a material that will

glow for hours in darkness following

brief exposure to ambient light.

The “T” shaped handle will be

located either on the luggage

compartment door (lid) or inside

the luggage compartment near the

tail lamps.

WARNING: Keep vehicle

doors and luggage

compartment locked and keep

keys and remote transmitters out

of a child’s reach. Unsupervised

children could lock themselves in

the trunk and risk injury. Children

should be taught not to play in

vehicles.

Locks and Security

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

WARNING: Do not leave children, unreliable adults, or animals

unattended in the vehicle. On hot days, the temperature in the

trunk or vehicle interior can rise very quickly. Exposure of people or

animals to these high temperatures for even a short time can cause

death or serious heat-related injuries, including brain damage. Small

children are particularly at risk.

REMOTE ENTRY SYSTEM

The integrated keyhead transmitter (IKT) complies with part 15 of the

FCC rules and with RSS-210 of Industry Canada. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

The typical operating range for your IKT is approximately 33 feet

(10 meters). A decrease in operating range could be caused by:

• weather conditions,

• nearby radio towers,

• structures around the vehicle, or

• other vehicles parked next to your vehicle.

Locks and Security

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

The IKT allows you to:

• remotely unlock the vehicle

doors.

• remotely lock all the vehicle

doors.

• remotely open the trunk.

• activate the personal alarm.

• arm and disarm the active

anti-theft system.

• operate the illuminated entry

feature.

The remote entry lock/unlock feature operates in any ignition position

except while the key is held in the start position. The panic feature

operates with the key in the off position.

If there are problems with the remote entry system, make sure to take

ALL integrated keyhead transmitters with you to the authorized

dealer in order to aid in troubleshooting the problem.

Unlocking the doors/two-stage unlock

1. Press and release to unlock the driver’s door. Note: The interior

lamps will illuminate.

2. Press

and release again within five seconds to unlock the

passenger door.

The remote entry system activates the illuminated entry feature; this

feature turns on the lamps for 25 seconds or until the ignition is turned

to the on position.

The inside lights will not turn off if:

• they have been turned on using the dimmer control or

• any door is open.

The battery saver feature will turn off the interior lamps 30 minutes after

the ignition is turned to the off position.

Two-stage unlocking may be disabled or re-enabled by simultaneously

pressing the

and controls on the IKT for four seconds (disabling

Locks and Security

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

two stage unlock allows all vehicle doors to unlock simultaneously). The

turn lamps will flash twice to indicate that two-stage unlock was enabled

or disabled.

Locking the doors

1. Press and release to lock all the doors. The turn signal lamps will

illuminate. Note: The interior lamps will turn off (unless the dome lamp

control is in the full-up position), and the turn signal lamps will flash if

all doors, trunk and hood (if equipped with active anti-theft system) are

closed. If the vehicle is not equipped with the active anti-theft system,

the turn signal lamps will flash if all doors, trunk and hood are closed.

The parking lamps will illuminate.

2. Press

and release again within three seconds to confirm that all

the doors, trunk and hood are closed. Note: The doors will lock again,

the horn will chirp once and the turn signal lamps will flash once more.

If any of the doors, trunk or hood (if equipped with active anti-theft

system) are not properly closed the horn will make two quick chirps and

the turn signal lamps will not flash. If the vehicle is not equipped with

the active anti-theft system, the horn will make two quick chirps and the

turn signal lamps will not flash if either door or the trunk are not closed.

Car finder

Press

twice within three seconds. The horn will chirp and the turn

lamps will flash. It is recommended that this method be used to locate

your vehicle, rather than using the panic alarm.

Sounding a panic alarm

Press

to activate the alarm. The horn will sound and the turn signal

and interior lamps will flash for a maximum of approximately three

minutes. Press

again or turn the ignition to the accessory or on

position to deactivate, or wait for the alarm to time-out in approximately

three minutes.

Note: The panic alarm will only operate when the ignition is in the off

position.

Opening the trunk

Press

twice to open the trunk.

• Ensure that the trunk is closed and latched before driving your

vehicle. Failure to properly latch the trunk may cause objects to fall

out or block the driver’s rear view.

Locks and Security

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

The remote entry system allows you to open the trunk while the ignition

is in any position. However, if the ignition is in the on position and the

vehicle is in motion, the trunk will not open if the vehicle is moving

3 mph (5 km/h) or faster.

In the event of battery failure, you

can open the trunk on the

convertible by using your master

key in the key cylinder between

the seat cushion located in the

back seat on the driver’s side.

Replacing the battery

The integrated keyhead transmitter uses one coin type three-volt lithium

battery CR2032 or equivalent.

To replace the battery:

1. Twist a thin coin in the slot of the

IKT near the key ring in order to

remove the battery cover.

Note: Do not wipe off any grease on

the battery terminals on the back

surface of the circuit board.

2. Remove the old battery.

Note: Please refer to local

regulations when disposing of

transmitter batteries.

3. Insert the new battery. Refer to

the instructions inside the IKT for

the correct orientation of the

battery. Press the battery down to

ensure that the battery is fully

seated in the battery housing cavity.

4. Snap the battery cover back onto

the key.

Locks and Security

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

Note: Replacement of the battery will not cause the IKT to become

deprogrammed from your vehicle. The IKT should operate normally after

battery replacement.

Replacing lost integrated keyhead transmitters (IKTs)

If you would like to have your integrated keyhead transmitters

reprogrammed because you lost one, or would like to buy additional

IKTs, you can either reprogram them yourself, or take all IKTs to your

authorized dealer for reprogramming.

How to reprogram your integrated keyhead transmitters (IKTs)

To program a new integrated keyhead transmitter yourself, refer to

Programming spare keys in the SecuriLock威 passive anti-theft system

section of this chapter. Note: At least two IKTs are required to perform

this procedure yourself.

Illuminated entry

The interior lamps and turn signal lamps illuminate when the integrated

keyhead transmitter is used to unlock the door(s).

The illuminated entry system will turn off the interior lights if:

• the ignition switch is turned to the on position, or

• the integrated keyhead transmitter lock control is pressed, or

• after 25 seconds of illumination.

The inside lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

Illuminated exit

• When all vehicle doors are closed and the key is removed from the

ignition, the interior dome lamp and the turn signal lamps will

illuminate.

The lights will turn off if all the doors remain closed and:

• 25 seconds elapse, or

• the key is inserted in the ignition.

Locks and Security

100

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

Battery saver

The battery saver will shut off the interior lamps 10 minutes after the

ignition has been turned to the off position and a door is left open, and

in 30 minutes if the dome lamp control is left on and the ignition has

been turned to the off position. The battery saver will also shut off the

trunk lamps in 30 minutes if the trunk is left open.

SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEM

SecuriLock威 passive anti-theft system is an engine immobilization

system. This system is designed to help prevent the engine from being

started unless a coded integrated keyhead transmitter (IKT)

programmed to your vehicle is used. The use of the wrong type of

coded key may lead to a “no-start” condition.

Your vehicle comes with two coded integrated keyhead transmitters;

additional coded IKTs may be purchased from your authorized dealer.

Standard SecuriLock威 keys without remote entry transmitter

functionality can also be purchased from your authorized dealer if

desired. The authorized dealer can program your spare IKTs to your

vehicle or you can program the IKTs yourself. Refer to Programming

spare keys for instructions on how to program the coded key.

Note: The SecuriLock威 passive anti-theft system is not compatible with

non-Ford aftermarket remote start systems. Use of these systems may

result in vehicle starting problems and a loss of security protection.

Note: Large metallic objects, electronic devices that are used to

purchase gasoline or similar items, or a second coded key on the same

key chain may cause vehicle starting issues. You need to prevent these

objects from touching the coded IKT while starting the engine. These

objects will not cause damage to the coded IKT, but may cause a

momentary issue if they are too close to the IKT when starting the

engine. If a problem occurs, turn the ignition off, remove all objects on

the key chain away from the coded IKT and restart the engine.

Note: Do not leave a duplicate coded key in the vehicle. Always

take your keys and lock all doors when leaving the vehicle.

Locks and Security

101

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

Anti-theft indicator

The anti-theft indicator is located in the instrument cluster.

• When the ignition is in the off

position, the indicator will flash

once every two seconds to

indicate the SecuriLock威 system

is functioning as a theft

deterrent.

• When the ignition is in the on position, the indicator will glow for

three seconds, then turn off to indicate normal system functionality.

If a problem occurs with the SecuriLock威 system, the indicator will flash

rapidly or glow steadily when the ignition is in the on position. If this

occurs, turn the ignition off then back to on to make sure there was no

electronic interference with the programmed key. If the vehicle doesn’t

start, try to start it with the 2nd programmed key and if successful

contact your authorized dealership for key replacement. If the indicator

still flashes rapidly or glows steadily, the vehicle will not start, contact

your authorized dealer as soon as possible for service.

Automatic arming

The vehicle is armed immediately after switching the ignition to the off

position.

The theft indicator will flash every

two seconds to act as a theft

deterrent when the vehicle is

armed.

Automatic disarming

Switching the ignition to the on position with a coded key disarms the

vehicle.

• The theft indicator will illuminate for three seconds and then go out.

• If the theft indicator stays on for an extended period of time or

flashes rapidly, contact your authorized dealer as soon as possible.

Replacement integrated keyhead transmitters (IKT) and coded keys

Note: Your vehicle comes equipped with two integrated keyhead

transmitters (IKTs). The IKT functions as both a programmed ignition

key that operates all the locks and starts the vehicle, as well as a remote

keyless entry transmitter. A maximum of eight coded keys can be

Locks and Security

102

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

programmed to your vehicle; only four of these eight keys can be IKTs

with remote entry functionality.

If your IKTs or standard SecuriLock威 coded keys are lost or stolen and

you don’t have an extra coded key, you will need to have your vehicle

towed to an authorized dealer. The key codes need to be erased from

your vehicle and new coded keys will need to be programmed.

Replacing coded keys can be very costly. Store an extra programmed key

away from the vehicle in a safe place to help prevent any

inconveniences. Please visit an authorized dealer to purchase additional

spare or replacement keys.

Programming spare keys

You can program your own integrated keyhead transmitters or standard

SecuriLock威 coded keys to your vehicle. This procedure will program

both the engine immobilizer keycode and the remote entry transmitter

portion of the IKT to your vehicle. Note: A maximum of eight coded

keys can be programmed to your vehicle; only four of these eight can be

IKTs with remote entry functionality.

Tips:

• Only use integrated keyhead transmitters (IKTs) or standard

SecuriLock威 keys.

• You must have two previously programmed coded keys (keys that

already operate your vehicle’s engine) and the new unprogrammed

key(s) readily accessible.

• If two previously programmed coded keys are not available, you must

take your vehicle to your authorized dealer to have the spare key(s)

programmed.

Please read and understand the

entire procedure before you begin.

1. Insert the first previously

programmed coded key into the

ignition.

2. Turn the ignition from the 1 (off)

position to the 3 (on) position. Keep

the ignition in the 3 (on) position

for at least three seconds, but no

more than 10 seconds.

3. Turn the ignition to the 1 (off) position and remove the first coded

key from the ignition.

Locks and Security

103

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

4. After three seconds but within 10 seconds of turning the ignition to

the 1 (off) position, insert the second previously coded key into the

ignition.

5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep

the ignition in the 3 (on) position for at least three seconds, but no more

than 10 seconds.

6. Turn the ignition to the 1 (off) position and remove the second

previously programmed coded key from the ignition.

7. After three seconds but within 20 seconds of turning the ignition to

the 1 (off) position and removing the previously programmed coded

key, insert the new unprogrammed key (new key/valet key) into the

ignition.

8. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep

the ignition in the 3 (on) position for at least six seconds.

9. Remove the newly programmed coded key from the ignition.

If the key has been successfully programmed it will start the vehicle’s

engine and will operate the remote entry system (if the new key is an

integrated keyhead transmitter). The theft indicator light will illuminate

for three seconds and then go out to indicate successful programming.

If the key was not successfully programmed, it will not start your

vehicle’s engine and/or will not operate the remote entry features. The

theft indicator light may flash on and off. Wait 20 seconds and you may

repeat Steps 1 through 8. If failure repeats, bring your vehicle to your

authorized dealer to have the new key(s) programmed.

To program additional new unprogrammed key(s), wait 20 seconds and

then repeat this procedure from Step 1.

ACTIVE ANTI-THEFT SYSTEM (IF EQUIPPED)

The active anti-theft system is designed to warn you in the event of an

unauthorized entry to your vehicle and is also designed to help prevent

the unwanted towing of the vehicle.

When the vehicle is locked and armed, the active anti-theft system

monitors the following:

• Doors

• Hood

• Trunk

• Movement inside the vehicle

Locks and Security

104

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

• Change in vehicle inclination

Note: The active anti-theft system includes a motion detection system

which monitors the passenger cabin and a vehicle incline sensor which

detects changes in vehicle attitude.

The interior motion detection and vehicle incline sensing systems

will operate only when the vehicle is locked using the remote

keyless entry transmitter or when using the power door lock

control with the accompanying door open and all doors then

become closed. For convertible vehicles, the convertible top must

be in the fully closed and latched position for the interior motion

sensing system to arm. If you lock the vehicle using the key in the

driver door key cylinder, the system will monitor the doors,

trunk, and hood but the interior motion sensing and vehicle

incline sensing will not arm.

Do not arm the interior motion detection system if movement within the

vehicle is likely to occur. Additionally, do not arm the vehicle incline

sensing system when the vehicle is in transport.

For proper operation of the interior motion detection system, ensure all

windows are closed prior to arming the system. This will help prevent

accidental alarm activation due to external influences and ensure proper

interior motion detection. Additionally, the interior motion sensing

system will not arm if either door or the trunk is ajar.

If there is any potential perimeter anti-theft problem with your vehicle,

ensure ALL integrated keyhead transmitters are brought to the

authorized dealer to aid in troubleshooting.

Arming the system

When armed, the active anti-theft system is designed to notify you of an

unauthorized entry. When unauthorized entry or towing occurs, the

system will flash the turn signal lamps and interior lamps and will sound

the horn.

The system is ready to arm whenever the key is out of the ignition. Any

of the following actions will arm the alarm system:

• Press the

control on the remote entry transmitter portion of your

integrated keyhead transmitter.

• Lock all doors using the interior power lock switch while the driver or

passenger door is open and then becomes closed.

• Lock the driver door with the key in the key lock cylinder (this will

not however arm the interior motion or vehicle incline sensing

systems).

Locks and Security

105

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

There is a 20 second countdown when any of the above actions occur

before the vehicle becomes armed.

Each door, the hood or the trunk is armed individually, and if any are

open, they must be closed for the system to enter the 20 second

countdown.

The turn signal lamps will flash once when all doors, the hood and the

trunk are closed indicating the vehicle is locked and entering the

20 second countdown. If any closure is not properly closed the turn

signal lamps will not flash and that closure will not be armed.

Disarming the system

You can disarm the system by any of the following actions:

• Unlock the doors by using the remote entry transmitter portion of

your integrated keyhead transmitter.

• Turn ignition to the on position with a valid programmed SecuriLock威

key or integrated keyhead transmitter (IKT).

• Press the panic control on the remote entry transmitter portion of

your IKT. This will only shut off the horn and turn lamps when the

alarm is sounding. The alarm system will still be armed.

• Use a key in the driver’s door to unlock the vehicle.

Pressing the power door unlock control within the 20 second prearmed

mode will return the vehicle to a disarmed state.

Note: Unlocking the trunk inhibits the motion sensing system but the

system continues to monitor the doors, hood and vehicle incline. Once

the trunk becomes closed the motion sensing system will rearm.

Triggering the anti-theft system

The armed system will be triggered if:

• Any door, the hood or the trunk is opened without using the remote

entry transmitter portion of your IKT or key in driver door cylinder.

• The ignition is turned to the on position with an invalid

unprogrammed SecuriLock威 key or IKT.

• The vehicle is towed/inclined.

• Motion is detected in the interior passenger compartment.

Locks and Security

106

2010 05+ Mustang (197)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security for Your Ford Mustang 2 Door Fifth Generation (2005-2014)

Related Topics

Popular Owner Manuals

Latest Owner Manuals